All Available Parts - 1967 Ford Mustang
Products (Click sub-categories above to ONLY display results for that Sub-Category) 3001-3100 of 3115
Sorted By:
Availability:
Display Options:
Availability: Out of Stock, On Order
Item #: 26131 -
This threaded replacement wand will require you to cut 8/32" fine threads in your original controller. Your OEM mirror controller is made of a very soft metal so one can often install these as "self tapping".1967 and 1968 are different, see comparison picture. The 1968 version was rounded off due to new safety standards. The mirror nut tool will fit over the 1967 wand, but not the 1968.
Availability: Out of Stock
Item #: 22621 -
Reproduction rubber bumper for your 67 - 73 Cougar or Mustang door latch mechanism. The bumper sits on the inside of your door latch mechanism, and is there to dampen the blow from the striker when you close your door.
Availability: Out of Stock, On Order
Item #: 14351 -
Convenient matched sets save costly locksmith work. Kits includes a pair of door lock cylinders. Comes with two keys. Includes door cylinder gaskets. Replaces Ford Part # : D2AZ-6521984-A
Availability: Out of Stock
Item #: 31711 -
Concours? almost, these are stainless steel screws with the wax tipped coating like the originals, for installing the door sill plates. The wax was deemed necessary by the Ford Motor Co. as a seal. These can be used on all years 1967-73 Mercury Cougar, Ford Mustang and most all other Ford, Mercury, Lincoln cars of the era. Works well with any of the reproduction sill plates, these were really made to be used with the premium reproduction sill plates in stainless steel. 1967-68 Cougar and...
Availability: Out of Stock
Item #: 33132 -
New Old Stock set of brushes only fits the Eaton brand of air compressor clutch. Pitts compressor clutch is the most common one starting in 1969. These are exact reproductions made from the original tooling.Ford part #: C8SZ-2979-A
Availability: Out of Stock, On Order
Item #: 26324 -
Concours? almost, these are stainless steel screws with the wax tipped coating like the originals, for installing the door sill plates. The wax was deemed necessary by the Ford Motor Co. as a seal. These can be used on all years 1967-73 Mercury Cougar, Ford Mustang and most all other Ford, Mercury, Lincoln cars of the era. Works well with any of the reproduction sill plates, these were really made to be used with the premium reproduction sill plates in stainless steel. 1967-68 Cougar and...
Availability: Out of Stock, On Order
Item #: 14974 -
These interchange left to right, they are a mirror image of one another. We recently did a side by side comparison of these so called "concours" sill plates and found very little difference when comparing them to the "economy" version... They both weigh .52 pounds, just like our NOS sill plates. They both have a high of luster, unlike the originals which featured very little "shine". We found the screw holes to be just a tad larger on the economy version but once the screw is inserted you...
Availability: Out of Stock
Item #: 24081 -
C7SZ-3D600-A Power steering pump adjusting spacer for use without air conditioning. For most 1967 - 1969 Mercury Cougar or Ford Mustang with 289, 302, 390, 428CJ engines, excludes 1969 351W and 1969 Boss 302 engines. Spacer dimensions: 7/16" I.D. x 1" O.D. and 1/2" thick. Same thickness as the pedestal bracket for air conditioning.
Availability: Out of Stock, On Order
Item #: 11336 -
New replacement J-nut or they are sometimes called U-nuts. These clip into those square holes in the fender aprons for fastening the fenders on 1967-70 Mercury Cougar and Ford Mustangs. These clips are 5/8 inches from the hole center to folded edge. We also see the same clips with 27/32 inch spacing for fender mounting. Numerous other uses, we find this clip on the hidden headlight buckets on 1967-68 Cougar and XR7's.
Availability: Out of Stock
Item #: 23988 -
For 1967-68 Mercury Cougars and Ford Mustangs with the 289 or 302 engine. This is an Eaton manufactured pulley and clutch assembly with a pulley diameter of 6-5/16", a clutch diameter of 6", and an overall thickness of 2-1/16 inches. Ford part # C7AA-2981-F.
Availability: Out of Stock
Item #: 23990 -
Used pulley and clutch assembly for Mercury Cougars and Ford Mustangs with the 390 engine. This is an Eaton manufactured pulley and clutch assembly with a pulley diameter of 6-3/4", a clutch diameter of 6", and an overall thickness of 2 inches. Whew, say that 5 times fast!Ford part # C7AA-2981-H.
Availability: Out of Stock
Item #: 23991 -
For 1967 - 1969 Mercury Cougars and Ford Mustangs with the 390 or 428CJ engine. This is a Pitts manufactured pulley and clutch assembly with a pulley diameter of 6-11/16", a clutch diameter of 6", and an overall thickness of 1-5/8 inches. Whew, say that 5 times fast!Ford part # C7AA-2981-J.
Availability: Out of Stock
Item #: 24072 -
For 1967-69 Mercury Cougars and Ford Mustangs with the 390 engine. This is an Eaton manufactured pulley and clutch assembly with a pulley diameter of 6-3/4", a clutch diameter of 6", and an overall thickness of 2 inches. Whew, say that 5 times fast!Ford part # C7SA-2981-A.
Availability: Out of Stock
Item #: 27466 -
Clevis type attaching clip for attaching the accelerator throttle rod to the carburetor on all 1967 and 1968 Cougars. The correct installation is with the clip pushed on from the top, barbs down. This is the right handed style.Original Ford part number C2VY-9826-A
Availability: Out of Stock
Item #: 11066 -
Metal rod that hooks to the carburetor linkage and the accelerator pedal bellcrank, or shaft. Rod measures 12-31/32 inches long. 1967 Mercury Cougar and Ford Mustang with S code 390-4V engines. Hooked end goes into the carburetor linkage, threaded end to the rear. Ford part number C7ZZ-9A702-A. A rod end clevis clip is needed for attachment to the carburetor – see part B7A-9826-A. *Note – not for use with factory cruise control.
Availability: Out of Stock
Item #: 11072 -
Metal rod that hooks to the carburetor linkage and the accelerator pedal bellcrank, or shaft. Rod measures 12-31/32 inches long. Application 1967 Mercury Cougar and Ford Mustang with 390-4V and cruise or speed control. Ford part number C7ZZ-9A702-D. Hooked end goes into the carburetor linkage, threaded end to the rear. A rod end clevis clip is needed for attachment to the carburetor – see part B7A-9826-A. *Note – for use with factory cruise control.
Availability: Out of Stock
Item #: 14250 -
Reproduction of the plastic square hood insulation clips. 11 used on most vehicles. Sold individually.
Availability: Out of Stock
Item #: 20192 -
This fits behind the door panel and is needed to install your remote mirror correctly.*NOTE*1969 Cougar owners do not need this part as it is built in the the chromed plastic, rectangular bezel on the door panel.
Availability: Out of Stock, On Order
Item #: 41150 -
AMK engine fastener kit for 1967 Mercury Cougar and 1966-67 Ford Mustang all with C or A code 289 engines without air conditioning. This kit claims to have 122 pieces.Kit typically includes: fasteners to attach air cleaner, carburetor, crank pulley, distributor / points / condenser / vacuum advance, drain plugs, engine tag, exhaust manifolds, fan / fan clutch, fuel pump, shroud, ignition coil and strap, intake manifold, oil filter adapter, oil pan, starter, timing cover, valve covers, water...
Availability: Out of Stock
Item #: 30642 -
Sold individually, original glove box cable screw with shoulder. For any 1967-70 Mercury Cougar or Ford Mustang. Probably many other Ford and Mercury cars also.Ford part number 379202-S2.
Availability: Out of Stock
Item #: 11-0428 -
Used Vent Frame Bolt Kit 1967 and 1968 Mercury Cougar and Ford Mustang.Consists of: 1 bolt - 379384-S2 1 bolt - 378694-S 2 lock nuts - 33797-S2 set screws - 375694-S2
Availability: Out of Stock
Item #: 23780 -
Used on front re-tractors, two per side on either side of the re-tractor mounting hole. Used to prevent rattles.
Availability: Out of Stock
Item #: 26132 -
Used seat belt bolt washer for the Mercury or Ford.
Availability: Out of Stock
Item #: 23964 -
C6ZZ-6582-H Smooth chromed valve cover without "Powered by Ford" embossed in the metal. Correct on 1967 DGS Mercury Cougar and optional on 1965-67 Ford Mustang with 289 engines. Ford master parts catalog shows a right and left version of this cover those numbers are C6ZZ-6582-H & C6ZZ-6582-J. *Note - This is a used chrome valve cover. The plating was pretty low quality back in 1966-67 and these will show rust pitting. For best results we recommend the painted version of this valve cover...
Availability: Out of Stock
Item #: 16204 -
Used oil fill cap for 1967 Mercury Cougar or Ford Mustang with 289 and California emissions. This chromed push on oil cap was used on the DGS package or engine dress up kit which included chrome valve covers and air cleaner lid. Identified by the vertical pointing elbow, for attaching a hose to the air cleaner base. Marked FoMoCo on the top inside a rectangle box.*Note - a Black painted version was also available on most 289 engines sold in California. This icon means that we're looking to buy...
Availability: Out of Stock
Item #: 16205 -
Used oil fill cap for 1967 Mercury Cougar or Ford Mustang with 289 and California emissions. This black painted push on oil cap was on California sold cars with closed emissions systems. Identified by the vertical pointing elbow, for attaching a hose to the air cleaner base. Marked FoMoCo on the top inside a rectangle box.*Note - a chromed version was also available with engine dress up kits.
Availability: Out of Stock, On Order
Item #: 31378 -
Concours correct dipsticks for 1967 - 1969 big block engines. These are exact reproductions of the originals with the proper length and oil level for these big block FE's. They have all of the correct markings including the Ford part number and recommended oil weight. Each dipstick is finished with a show quality chrome handle capped with the correct plastic plug. Ford part # C7OZ-6750-A, Ford casting # C7OE-6750-A.
Availability: Out of Stock, On Order
Item #: 15037 -
Kit includes two brackets and grommets for routing battery cable between starter and solenoid on inner fender. Replaces Ford Part # : C5ZZ-14302-K
Availability: Out of Stock
Item #: 23776 -
Front retractor bolt, used in conjunction with two rubber spacer / washers and one washer. The two rubber washers go on either side of the re-tractor mounting hole and the metal washer is against the inner rocker.
Availability: Out of Stock
Item #: 11270 -
Nice reproduction oil dipstick made from all steel, painted Ford engine blue. Only fits 289 or 302 Ford engines from 1967-73. These dipstick tubes have the 'full' and 'add' markings in the correct place, however they do not have any Ford part numbers stamped on them. Black steel as shown, not plain shiny steel like originals. Replaces Ford part # C7OE-6750-B or C8OE-6750-B.
Availability: Out of Stock
Item #: 11360 -
Availability: Out of Stock
Item #: 33552 -
Used oil screen pick up tube assembly from a FE or big block 1966-70 Ford car, such as 352, 390, 410, 428, or 428CJ engine. This is for most front sump oil pans. Used item, should be degreased and cleaned inside and out prior to installation. Tube assemblies with damaged screens, damaged tubes or bends are thrown away or scrapped. We only save undamaged, used oil pick up tubes. Melling sells a quality reproduction of this item. Replaces Ford Part #: C6OZ-6622-A ...
Availability: Out of Stock, On Order
Item #: 11794 -
This reproduction universal joint fits the differential end of the drive axle and is used on all Mercury Cougars or Ford Mustangs equipped with the 289, 302, 351 Windsor as well as most 351 Clevelands (see chart). Includes a grease fitting for extended life. 3.25" span cups are 1.12" and 1.00" diam. Replaces Ford part # C3AZ-4635-F.
Availability: Out of Stock
Item #: 16-0047 -
Application; 390, 427, 351CJ, 428CJ, and 429CJ all with C6 transmission. 428CJ and 429CJ 4 speed transmissions. 1970 351C-4v with FMX.U-joint size 1330, overall length 8-3/4 inches.
Availability: Out of Stock
Item #: 31582 -
Leaf spring front bolts for any 1967 Mercury Cougar or Ford Mustang. For some reason the 1967 bolts are a bit longer than later years. AMK F-1065, About 6-1/2 inches long. 6 total pieces, 2 bolts, 2 heavy washers, 2 nuts.
Availability: Out of Stock
Item #: 41364 -
Sold individually. Has correct flattened area at top. Competition handling size, measures 7" from inner radius to end of threads. Thread size 7/16-20". Does not include the OEM style nuts, those are an optional addon. Replaces Ford Part #: C6OA-5705-C
Availability: Out of Stock
Item #: 32931 -
NOTE! When we ship a rear end, we will remove the third member and ship it in a separate box. Some assembly will be required. Housing overall width - 54-1/4 inches flange to flange. Overall width measured from faces of axles, not the tips. All 1967-70 have the same overall width of 59-1/2 inches. This economy version of our 8 inch rear end assembly is perfect for those intending to add rear disc brakes to their car. Spring perches are 43 inches apart on center. Axle...
Availability: Out of Stock
Item #: 31253 -
Good used axle vent nipple or tube. This vent tube screws into the top of the rear axle and is a breather / vent to equalize the pressure inside the axle tube. Fits both 8 inch and 9 inch rear axles. Fits Mercury Cougar and Ford Mustang 1967-73. A (5/16" inside diameter) rubber hose about 18-1/4 inches long attaches to the nipple. Has a very tiny diameter hole inside, about 0.062". Needs to be kept clear to work properly. Also see the reproduction version from AMK. Concours hose kit with...
Availability: Out of Stock
Item #: 30532 -
Used pinion yoke for an 9 inch rear end on any 1967-73 Mercury Cougar or 1967-73 Ford Mustang. 1310 U-Joint. Part cleaned for pictures, used parts shipped the way they come off of the cars. Shipped bare, no hardware included.Ford part number C3AZ-4851-L.
Availability: Out of Stock
Item #: 30653 -
Also called a pumpkin, 3.00:1 locking ratio.Check your door tag under "Axle".Please note, that this is a vintage, two pin equa lock third member. Most of us should be looking at a modern design traction lock for spirited driving. The 1960's Equa-Lock, is pretty weak.1967 code A 1968 code E
Availability: Out of Stock
Item #: 27513 -
NOTE! When we ship a rear end, we will remove the third member and ship it in a separate box. Some assembly will be required. Housing overall width - 54-1/4 inches flange to flange. Spring perches are 43 inches apart on center. Overall width measured from faces of axles, not the tips. All 1967-70 have the same overall width of 59-1/2 inches. Rear axle assembly - Housing, Axles, brake backing plates, and third member. 1967 late 9 inch rear end housings without fill plug in the steel...
Availability: Out of Stock
Item #: 26525 -
Mounts on floor pan above the center of the rear axle over 3rd member on small block cars with 8 inch rear ends. Mustang only, will not fit a Cougar.Replaces Ford part #: C5ZZ-4730-B orC3AZ-4730-B. Customer Comment:Thank You Don and WCCC,Copy Cat's almost done!Yesterday was such a nice day I took Copy Cat out to Show Don and Lin the final (almost) product.Without their patience and understanding along with a great selection of parts I wouldn't have her in such great shape.Thanks guys, along...
Availability: Out of Stock
Item #: 24268 -
NOTE! When we ship a rear end, we will remove the third member and ship it in a separate box. Some assembly will be required. Rear axle assembly - Housing, Axles, brake backing plates, and third member. Housing overall width - 54-1/4 inches flange to flange. Spring perches are 43 inches apart on center. 1967 early 9 inch rear end housings had the carry over fill plug in the steel housing as seen from the back of the car. As removed from West Coast Cougar organ donor car. We recommend a bearing...
Availability: Out of Stock
Item #: 23809 -
C3AZ-4730-B Rubber bumper that mounts to the metal axle snubber on Ford nine inch rear ends on 1967 - 1970 Mercury Cougar and Ford Mustangs. Good used part with solidly mounted metal threaded stud. Pinion bumper. The casting number seen on the 67-68 is C3AA-4906-C, this version has fine threads. The version most often seen on the 69-70 is C9OA-4906-A. It will have a coarse threaded mounting stud. Two of these were used on certain 1967 Shelby Mustangs with traction bars.
Availability: Out of Stock, On Order
Item #: 14624 -
Kit comes complete with accelerator linkage rod, bushings and clip kit and return spring. Replaces Ford Part #: c5zz-9a702
Availability: Out of Stock
Item #: 24313 -
"L" shaped bracket that mounts to the rear carburetor mounting hole for attaching the return spring. Bracket faces forward when installed. *Note - This bracket is a bit longer than the 2V version.
Availability: Out of Stock
Item #: 24070 -
"L" shaped bracket that mounts to the rear of the Holley carburetor mounting hole for attaching the return spring. Bracket faces forward when installed.
Availability: Out of Stock
Item #: 25076 -
Also called a pumpkin, 2.79:1 open ratio. Check your door tag under "Axle".
1967 code 0 (zero) 1968 code 2
Availability: Out of Stock
Item #: 13154 -
NOS seat belt warning light relay for most Ford Lincoln and Mercury cars starting in 1967 until sometime in 1972 when a Motorcraft version of this exact relay was produced. This is a timed relay that allows several seconds of illumination to your seat belt warning light. Ford Part number C7AB-10B924-B1, Ford Service part number D1AZ-10B924-A or D2AB-10B924-AA.
Availability: Out of Stock
Item #: 13953 -
Neat detail item, stamped steel with zinc plating. Mounts on intake manifold and holds one end of the accelerator linkage spring for the 289 / 302.
Availability: Out of Stock
Item #: 12667 -
This is a core five piece set of front windshield mouldings for a 1967 - 1968 Mercury Cougar. These mouldings need restoration as they are dull, scratched and dinged. They would suffice to make a car complete if you were wanting to drive it but in our opinion they are a step below "good" driver quality. This set will not have any kinks, flattened out areas or holes, we discard mouldings of that description. We do not recommend the reproduction, "offshore" mouldings that are available as they...
Availability: Out of Stock
Item #: 12644 -
Driver side vertical windshield moulding. Suitable for restoration or could fit right in on your lower quality daily driver. Ford part number C5ZZ-6503137-B.
Availability: Out of Stock
Item #: 12668 -
Driver side upper windshield mouldinig. Suitable for restoration or could fit right in on or your lower quality daily driver. Ford part number C5ZZ-6503145-B.
Availability: Out of Stock
Item #: 12810 -
Core lower windshield moulding / trim for your Mercury Cougar or Ford Mustang. Suitable for restoration or could fit right in on your lower quality daily driver. Ford part # C5ZZ-6503148-B.
Availability: Out of Stock
Item #: 12651 -
Core passenger side (right hand) vertical windshield moulding / trim for your Mercury Cougar or Ford Mustang. Suitable for restoration or could fit right in on your lower quality daily driver. Ford part # C5ZZ-6503136-B.
Availability: Out of Stock
Item #: 12654 -
Core passenger side (right hand) upper windshield moulding / trim for your Mercury Cougar or Ford Mustang. Suitable for restoration or could fit right in on your lower quality daily driver. Ford part # C5ZZ-6503144-B.
Availability: Out of Stock
Item #: 32251 -
NOS upper moulding at the top of the windshield on the left hand side. Ford part number C5ZZ-6503145-B
Availability: Out of Stock
Item #: 32252 -
NOS passenger side (right hand) vertical windshield moulding / trim for your Mercury Cougar or Ford Mustang. Ford part # C5ZZ-6503136-B.
Availability: Out of Stock
Item #: 30260 -
Inner rectangular clip to hold on the rocker panel moulding on a 1967 or 1968 Ford Mustang or Mercury Cougar. Sold Individually. You can find the reproductions here.Ford Part number C7ZZ-6510182-A
Availability: Out of Stock
Item #: 15828 -
Reproduction turn signal switch connector for your 67 Cougar or Mustang. Work with either tilt or fixed columns. This is the connector that attaches the turn signal switch to the main dashboard wiring harness.
Availability: Out of Stock
Item #: 15-0059 -
Used in the latter part of 1967 and all of 1968 and 1969 to fasten the upper column cover to the column. Early 1967 used a chrome version of this screw.
Availability: Out of Stock
Item #: 15-0062 -
1967 Cougar Owners: To view our exploded view interactive diagram of the tilt steering column parts, click here. This is the part of the tilt switch that the turn signal wand screws into. This part is always included when you purchase a new turn signal switch. 1967-69 mechanism has two springs on either side, the 1970-73 mechanism uses just one spring. There is an active thread on the Classic Cougar Community Forum discussing tilt columns and trouble shooting. *NOTE* For tilt column service,...
Availability: Out of Stock
Item #: 15-0065 -
Emergency flasher bezel for the side of the tilt steering column. Another hard to find, fragile, plastic part. Subject to availability. Paint to match your interior.
Availability: Out of Stock
Item #: 15-0066 -
Steering column to steering box coupler, also known as a 'rag' joint. Used on 1967 1968 1969 1970 Cougar tilt columns, differs greatly from the fixed column version in that is has a "D" shaped fitting on the column side. Good used condition, supplied with one, 12 point attaching bolt. You will need to reuse your existing 12 point bolt for the other end or purchase a second one. *NOTE* WCCC services all FoMoCo tilt and tilt-tilt away steering columns 1967-1979. Our shop rate for this service is...
Availability: Out of Stock
Item #: 15-0057 -
Used upper steering column bearing for your 67 - 73 Cougar or Mustang. One required per car. Fixed Columns only use the upper bearing, while the tilt columns used an upper and lower. The used lower bearing can be found here. Outside diameter: 1 3/16 " * - may not fit some 67 Mustang applications with a fixed column as these used Ford part # C4OZ-3517-A, which is the same part used in the Fairlanes/Comets with a fixed column. To our knowledge this bearing is not currently reproduced. *NOTE* For...
Availability: Out of Stock
Item #: 15-0054 -
Rubber isolator used in tilt away steering column near the lower bearing. Two required per car. There is an active thread on the Classic Cougar Community Forum discussing tilt columns and trouble shooting. *NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year. ...
Availability: Out of Stock
Item #: 33107 -
Identified with the straight bracket compared to the 1968 relay which has a bend. Keep in mind we have a reproduction substitution for this part. Ford part # C7ZA-3E553-A. Ford packaging reads C7ZZ-10B926-A *NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year. Helpful tip: For those having trouble getting their tilt away mechanism to...
Availability: Out of Stock
Item #: 15-0022 -
Used pivot pin for the Mercury Cougar or Ford Mustang / Thunderbird equipped with a tilt / tilt away column. This is a pressed pin with a flange and five are required per car. This pin is internally threaded with a # 6-32 thread. Ford part # C7SZ-3D739-A. *NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year. ...
Availability: Out of Stock
Item #: 15-0046 -
One required per car, includes Phillips screw.*NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is the designer of all of our solid state sequential systems. There is no question he cannot answer! Here is a link to a great source of information on the subject. ...
Availability: Out of Stock
Item #: 15-0047 -
Used steering wheel tension spring used in the tilt / tilt away steering column found in the Mercury Cougar or Ford Mustang. One required per car. Keeps tension on the steering wheel shaft so as to keep the steering wheel from contacting the upper column cover. There is an active thread on the Classic Cougar Community Forum discussing tilt columns and trouble shooting. *NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC...
Availability: Out of Stock
Item #: 15-0040 -
1967 Cougar Owners: To view our exploded view interactive diagram of the tilt steering column parts, click here. Used vacuum reservoir for the tilt / tilt away steering column equipped Mercury Cougar or Ford Mustang. This is a 1967 only design that is very hard to find in rust free condition with a working vacuum check valve. Beware of substitutes as there are close facsimiles with different sized nipples, different brackets or plastic built in check valves. These versions off later model cars...
Availability: Out of Stock, On Order
Item #: 11330 -
Reproduction support brace to be used with 1967-70 Mercury Cougar and Ford Mustang export braces. Can be used with OEM, NOS or reproduction export braces. Contoured to match the curvature of the cowl.*Note - Will not fit early Shelby Mustangs.This part never came from the factory, but the idea was taken from the fact that Shelby cars had plates like these, though these are not interchangeable with Shelby export braces or export brace plates because of hole placement. The original Shelby part...
Availability: Out of Stock
Item #: 12868 -
Very clean rust free support with no rust or collision damage. It will come with the lower support but we cannot always provide a perfect one. If this is critical please call so we can check inventory before you order.
Availability: In-Stock Item
Item #: 31766 -
We think that this jumper or adapter wiring lead, was used in 1967 when the Neutral safety switch changed from two separate plugs to a single square 4 combination plug. There could have been an overlap where the plug from the firewall to the 14401 main under dash harness changed to the single square 4 combination plug. We have also observed the two separate neutral safety switch plugs plugged directly into the updated square 4 plug.
Availability: Out of Stock
Item #: 42027 -
If your are missing your factory Riv-Nuts, or you are installing a passenger side mirror, these are a very easy to use alternative to the metal riv-nuts we offer. Another good application for these is when your existing mirror mounting holes are "hogged out" these slightly over sized inserts are just the ticket. Keep in mind our kit is not only less money than others you may find but the screws are stainless steel. Hole size for these rubber inserts is 3/8". Keep in mind the upper lip stands a...
Availability: Out of Stock
Item #: 32336 -
Front steel vacuum fitting for 390, 427, 428CJ engines. New Old Stock. Replaces Ford part number C7AZ-9A474-A.
Availability: Out of Stock
Item #: 19991 -
This white plastic spacer fits into the back of the right hand inner knob on cars without factory fader or balance. If your inner knob is loose and will not align, you will want to see if this part is in place. The pictures show an example of how it looks once installed. 1968-70 AM-FM radios would not utilize this part because they have a balance feature. Also found on various 1976-70 Ford and Mercury cars such as Galaxie, Fairlane, Torino, Ranchero, Falcon, Montego, and Thunderbird. The knobs...
Availability: Out of Stock, On Order
Item #: 14916 -
Sold as a pair, these are a perfect fit, correct texture and are less prone to cracking than originals. They do not have the perforated speaker holes for those utilizing kick panel speakers. Check out our custom made kick panels that accommodate modern speakers.
Availability: Out of Stock, On Order
Item #: 14918 -
Reproduction interior kick panels in parchment / off-white for the Mercury Cougar or Ford Mustang. Sold as a pair, these are a perfect fit, correct texture and are less prone to cracking than originals. They do not have the perforated speaker holes for those utilizing kick panel speakers. Check out our custom made kick panels that accommodate modern speakers.
Availability: Out of Stock, On Order
Item #: 14920 -
Sold as a pair, these are a perfect fit, correct texture and are less prone to cracking than originals. They do not have the perforated speaker holes for those utilizing kick panel speakers. Check out our custom made kick panels that accommodate modern speakers.
Availability: Out of Stock
Item #: 11320 -
Used threaded PCV valve for use on 390-4V, 428CJ, 427-4V cars from 1967-70. Unknown functioning condition, these have the correct threaded tops and work with either of the 90° elbows available, reproduction or OEM Ford.
Availability: Out of Stock
Item #: 25677 -
This adapter is threaded on bottom for PCV valve and 6 degree angled 5/8" nipple on side. Was gold Cadmium plated, not painted. Original Ford part number C7OZ-6A706-A.
Availability: Out of Stock
Item #: 24301 -
C7ZZ-6A664-B Original used hose that connects the original threaded PCV valve combination with C7OZ-6A706-A elbow and the 390 PCV transfer tube on the intake manifold. Molded hose with 5/8" valve end and 1/2" tube end. All 1967-68 S code 390GT or 390-4V engines and 1968-69 428CJ and 428SCJ engines, includes Cougar, Mustang, Fairlane, Torino, Ranchero, Cyclone, and Comet. Used hoses will have faded striping (if present), and clamp impressions. Very often the rubber will be hard and showing some...
Availability: Out of Stock, On Order
Item #: 14061 -
Precision machined to the factory specifications. Light gold anodize finish just like the original.
Availability: Out of Stock
Item #: 33116 -
New old stock driver side door handle the 1967-68 Mercury Cougar and 1965-70 Ford Mustang. This handle is NOS, NOS doesn't always mean high quality plating. Includes mounting hardware and pads. Round button not included. Replaces Ford Part #: C4DZ-6222405-A
Availability: Out of Stock
Item #: 33117 -
New old stock passenger side door handle the 1967-68 Mercury Cougar and 1965-70 Ford Mustang. This handle is NOS, NOS doesn't always mean high quality plating. Includes mounting hardware and pads. Round button not included. Replaces Ford Part #: C4DZ-6222404-A
Availability: Out of Stock
Item #: 27403 -
Tested and working emergency / parking or parking brake indicator switch and bracket. Standard switch found on 1967-68 Mercury Cougar XR7 models. Optional on Cougar standard model 65A and 65C, also optional on Ford Mustang. Clamps to the hand parking brake assembly. Ford part number C7ZZ-15A851-A This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of 50% of our web price for parts...
Availability: Out of Stock
Item #: 33110 -
NOS switch and bracket for the emergency / parking brake. Standard switch found on 1967-68 Mercury Cougar XR7 models. Optional on Cougar standard model 65A and 65C, also optional on Ford Mustang. Clamps to the hand parking brake assembly. Ford part number C7ZZ-15A851-A
Availability: Out of Stock, On Order
Item #: 41883 -
Premium concours quality door handle set for the Mercury Cougar. These handles are beautiful triple-plated nickel chrome. Includes mounting hardware and pads. Replaces Ford Part #: C7ZZ-6522404-A and C7ZZ-6522405-A
Availability: Out of Stock
Item #: 33235 -
New Old Stock passenger side (right hand) vent / wing window handle for the 1967 Mercury Cougar or Ford Mustang. Also fits 1966 Ford and Mercury mid sized cars. Ford part number C6OZ-6222916-A.
Availability: Out of Stock
Item #: 23993 -
Driver quality used right side or passenger side folding door handle. This type of handle was used on the 1967 XR7 models and 1968 Cougars. This is also the deluxe handle found in Mustang and other Ford / Mercury cars. Some pitting, will have a good spring and rubber bumper. Sorry mounting screw not included.
Availability: Out of Stock
Item #: 23994 -
Driver quality used left side or driver side folding door handle. This type of handle was used on the 1967 XR7 models and 1968 Cougars. This is also the deluxe handle found in Mustang and other Ford / Mercury cars. Some pitting, will have a good spring and rubber bumper. Sorry mounting screw not included.
Availability: Out of Stock
Item #: 11-0452 -
Good used original handle with no obvious pitting or blemishes. This handle was not used on the XR7. Found on 1967 standard model Cougar and 1967 base model Mustang. Ford casting number C7OB-6222614-A.*Note - 1967 Mustang with deluxe interior, i.e. brushed door panels, used a similar handle, but with Ford part number C7ZB....
Availability: Out of Stock
Item #: 32507 -
Used, with scratches and pits, suitable for every day driver or restoring.
Availability: Out of Stock
Item #: 11-0504 -
Used passenger side (right hand) spring from a door latch assembly fits many Ford and Mercury cars. This will fit all years 1967-70.
Availability: Out of Stock
Item #: 11-0505 -
Used driver side (right hand) spring from a door latch assembly fits many Ford and Mercury cars. This will fit all years 1967-70.
Availability: Out of Stock, On Order
Item #: 33181 -
Tall style filter for C4 transmissions. Fits all Ford C4 transmissions for any 1966-73 Mercury Cougar or Ford Mustang with that W code C-4 transmission. This is designated as the 'tall' filter, introduced in 1965. I guess that Ford installed a deeper pan in 1965? Solid metal construction with filter inside.
Availability: Out of Stock
Item #: 31333 -
C5OP-7976-A Aluminum bell housing, sometimes called a converter housing in the Ford shop manual. 1967 - 1968 Mercury Cougar with any 289 or 302 engine and automatic C4 transmission, code W on your door tag. 1967 - 1972 Ford Mustang with 250, 289, or 302 engine and automatic C4 transmission, code W on your door data plate. Fits the 157 tooth flex plates. There was a 164 tooth flex plate that came later. NOTE * Grade B bell housing will have a chip or heavy scarring on the bottom, see photo...
Availability: Out of Stock, On Order
Item #: 33160 -
Replacement seal with boot for all 1969-73 FMX and 1967-73 C6 transmissions. Tail shaft and slip yoke seal.
Availability: Out of Stock
Item #: 33173 -
Basic FMX transmission rebuild kit. Kit includes gaskets, seals, bands, filter, modulator, everything as shown. Fits all Ford FMX transmissions for any 1969-73 Mercury Cougar or Ford Mustang with that X code FMX transmission. Quality kit, same as supplied to professional shops.