All Available Parts - 1971 Ford Mustang
Products (Click sub-categories above to ONLY display results for that Sub-Category) 101-200 of 2463
Sorted By:
Availability:
Display Options:
Availability: In-Stock Item
Item #: 26181 -
For fixed steering wheel. Special molded rubber sleeve that holds the bearing in place. Exact reproduction. Replaces Ford part # D1AZ-3518 or E2AZ-3518
Availability: Out of Stock
Item #: 15-0083 -
Used plunger spring used in the bale of the tilt / tilt away steering column found in the Mercury Cougar or Ford Mustang. Small plunger spring for 1967-69 tilt columns. Maintains pressure on the heavy wire tilt release bale. This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of 50% of our web price for parts delivered in hand or by carrier to our Brooks, Oregon location. If you're not...
Availability: In-Stock Item
Item #: 15-0115 -
New foam insulation for the lower tube of the steering columns. Can be used on fixed and tilt columns, from 1968-73, on all Mercury Cougars, Ford Mustangs, and most all other Ford steering columns with a lower tube with inside diameter of 1-5/8 inches. The originals have almost always disintegrated. Adhesive probably isn't needed, but we recommend just a little drop of something to hold it in place. This is a dense foam insulation ring. DIY guys, this material can be found in bulk at home...
Availability: In-Stock Item
Item #: 11822 -
12-point bolt for attaching the steering column coupler to the steering box. Works for all 1967-73 Mercury Cougars and most other Fords, Mercury, and Lincolns. One bolt used for fixed columns, two bolts used on tilt steering columns. Sold individually.
Availability: In-Stock Item
Item #: 27601 -
Reproduction insulator for the lower portion of the steering column found on all 1969-73 Mercury Cougar or Ford Mustangs. Unique slide in plastic bushing or insulator, which slides into the bottom tube of both fixed and tilt columns. Most originals are broken or missing. Two sizes of insulators, please verify year and diameter.1968 tube measures 1 3/8"1969 - 1973 tube measures 1 5/8"*NOTE* WCCC services all FoMoCo tilt and tilt-tilt away steering columns 1967-1979. Our shop rate for this...
Availability: Used / Wrecking Yard Item
Item #: 15-0146 -
Used Release Spring for the 1967 - 1973 Mercury Cougar / 1967 - 1973 Ford Mustang
Availability: Used / Wrecking Yard Item
Item #: 15-0145 -
Used Spring Sleeve Cap for the 1967 - 1973 Mercury Cougar / 1967 - 1973 Ford Mustang
Availability: Used / Wrecking Yard Item
Item #: 15-0190 -
Used lower steering column shaft for 70 - 73 Cougars and Mustangs with a fixed column. Identified by length, and the round style lower flange. 1968-69 lower flange is slightly smaller with flat sides. Overall length is 16-3/8 inches.
Availability: In-Stock Item
Item #: 15-0173 -
Used return spring for any 1970 - 1978 Cougar or Mustang Tilt Column. This spring provides return tension on tilt steering wheels.*NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year.
Availability: In-Stock Item
Item #: 15-0203 -
This extension holds the inner spring tube in place on the 70 - 73 column.Ford part number: D0AA-3790-CW
Availability: In-Stock Item
Item #: 15-0178 -
Used snap ring that is used to hold the bearing on you the steering shaft. This ring was used on 67 - 78 fixed columns and 70 - 78 tilt columns. Not for use on 67 - 69 tilt columns.*NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year. ...
Availability: In-Stock Item
Item #: 15-0179 -
Used retainer / friction clip that replaces broken injected plastic shaft retainers on fixed or tilt steering collapsible columns on most FoMoCo products starting in 1968 and through the 70's. Ford part number C9AZ-3E629-B. *NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year. ...
Availability: In-Stock Item
Item #: 31804 -
This clip goes on the upper end of your column and keeps your steering shaft from moving around when you pull up on your steering wheel.
Spotlight!
Featured!
Availability: In-Stock Item
Item #: 32067 -
Reproduction 3D printed retainer / friction clip that replaces broken injected plastic shaft retainers on fixed or tilt steering collapsible columns on most FoMoCo products starting in 1968 and through the 70's. These installs on the upper piece of what Ford called the Steering Column Shaft Assembly, also known as the inner steering column collapsible shaft. The Steering Column Shaft Assembly is the 2 piece shaft that connects the steering wheel to the rag joint. The upper...
Availability: Used / Wrecking Yard Item
Item #: 32204 -
Used lower steering column shaft for 71 - 72 Cougars and Mustangs with a tilt column. *NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year.
Availability: In-Stock Item
Item #: 32897 -
Used sleeve for fixed steering wheel. Special molded rubber sleeve that holds the bearing in place. Ford part # D1AZ-3518 or E2AZ-3518
Availability: Used / Wrecking Yard Item
Item #: 33443 -
Used bracket for mounting a steering column to the instrument panel on any 1970-71 Mercury Cougar or Ford Mustang. Main bracket only, there is also a side support bracket that is also needed. Bracket also used on 1970 full sized Ford and Mercury cars, and 1970-71 Ford Maverick. Tilt and fixed steering columns.Ford part number D0AZ-3676-A.
Availability: Used / Wrecking Yard Item
Item #: 33444 -
Used lateral or side bracket for mounting the steering column to the instrument panel on any 1970-71 Mercury Cougar or Ford Mustang. Support bracket only, there is also a large support bracket that is also needed. Tilt and fixed steering columns.Bracket also used on 1970 full sized Ford and Mercury cars, and 1970-71 Ford Maverick. Ford part number D0ZZ-3B139-A.
Availability: Used / Wrecking Yard Item
Item #: 33452 -
Used lower steering column mounting bracket at firewall, for any 1971-73 Mercury Cougar or Ford Mustang. Rubber seal will need to be replaced, see related items for rubber seal. Ford part number D1ZZ-65017A50-A.
Availability: Used / Wrecking Yard Item
Item #: 15-0028 -
Correct nut that is designed not to come undone.
Availability: In-Stock Item
Item #: 30663 -
Availability: Ships Direct from Supplier (Except International)
Item #: 11992 -
Reproduction reinforcement plate designed to weld onto the lower control arms. Sold individually, we are not sure that you would want to even buy one of these. They don't fit very well, and are not contoured to any lower control arm on the market. You will be bending these to fit, prior to welding. *Note - This is a non-returnable item.
Availability: Used / Wrecking Yard Item
Item #: 16-0017 -
Used FMX transmission tail shaft or housing extension as Ford called them in the Master Parts Catalog. Fits all 1969-73 Mercury Cougar and Ford Mustang cars with transmission code X on the door tag. Cast aluminum construction. D2ZP-7A040-A version also available, we have a good supply of the updated 1972 version. The overall length of this housing is 12 7/8", which was also used on 1969 Fairlanes and Torinos. This housing will not fit full sized Ford Mercury cars that have an FMX,...
Availability: Used / Wrecking Yard Item
Item #: 30787 -
Good used OEM flex plate for all 69 - 73 Mercury Cougar and Ford Mustang with 302 / 351W engines, and C4 or FMX transmissions. Not for use on a 1968 with 302. The starter ring will show wear and some will choose to replace, others have removed the starter ring and just turned it around so the unused portion of the ring will now contact the starter drive gear. ...
Availability: In-Stock Item
Item #: 31243 -
New torque converter nuts for connecting torque converters to flex plates on 1967-73 Mercury Cougar or 1967-73 Ford Mustang or other Ford Lincoln Mercury that is not metric. 3/8-24 threads, Grade 8 nut with a 9/16 inch hex. 0.79" OD and 0.39" thick. Torque converters use 4 nuts for attachment.Ford number 377704-S
Availability: In-Stock Item
Item #: 32179 -
Brand new flex plate for all 1970-71 Mercury and Ford with 429CJ engines, and C6 transmissions. Comes complete with new starter ring gear installed as shown.
Availability: Used / Wrecking Yard Item
Item #: 16-0087 -
Used FMX transmission tail shaft or housing extension as Ford called them in the Master Parts Catalog. Fits all 1969-73 Mercury Cougar and Ford Mustang cars with transmission code X on the door tag. Cast aluminum construction. C9ZP-7A040-A version also available for slightly more money. Exact same part, just got updated for some engineering or manufacturing reason. The overall length of this housing is 12 7/8", which was also used on 1969 Fairlanes and Torinos. This housing will not...
Availability: In-Stock Item
Item #: 33159 -
Replacement seal with boot for all 1965-73 C4 Ford transmissions. Tail shaft and slip yoke seal.
Availability: In-Stock Item
Item #: 33162 -
Replacement tail shaft bushing, for all 1969-73 FMX and 1967-73 C6 transmissions.
Availability: In-Stock Item
Item #: 33188 -
Shift kit for the C6 transmission valve body for all 1967-73 and 1967-73 Mercury and Ford. This is a standard shift rebuilding kit for your stock valve body.
Availability: In-Stock Item
Item #: 33190 -
Shift kit for the FMX transmission valve body for all 1969-72 and 1969-72 Mercury and Ford. This is a standard shift rebuilding kit for your stock valve body.* Note - 1973 has a different shift kit, see related items.
Availability: In-Stock Item
Item #: 33182 -
Filter / screen for the C6 transmissions, for all 1967-73 and 1967-73 Mercury and Ford.
Availability: In-Stock Item
Item #: 33179 -
Replacement cork pan gasket for all 1965-73 C4 Ford transmissions.
Availability: In-Stock Item
Item #: 41135 -
These brackets are intended to make sure that the brake pads and the caliper stay in the correct alignment, as well as for anti-rattle. Replaces Ford Part # C8OZ-2B295-A. Sold individuallyCheck out our caliper tips and tricks video below: ...
Availability: In-Stock Item
Item #: 41136 -
Replaces Ford Part # 382713-S Sold individuallyCheck out our caliper tips and tricks video below: ...
Availability: In-Stock Item
Item #: 41130 -
Replaces Ford Part # C8AZ-2066-A
Sold individually
Availability: In-Stock Item
Item #: 41133 -
Reproduction disc brake caliper insulators for a large array of FoMoCo products starting in 1968. 2 are required per caliper, 4 total per vehicle. Sold as a pair. Replaces Ford part # C8AZ-2B299-A.Check out our caliper tips and tricks video below: ...
Availability: In-Stock Item
Item #: 41129 -
Replaces Ford Part # C8AZ-2069-A
Sold individually
Availability: In-Stock Item
Item #: 41131 -
Replaces Ford Part # 43260-S
Sold individually
Availability: In-Stock Item
Item #: 41040 -
This nut fits onto the strut brace at the front of the car, and not the control arm end. It is the lock nut that goes on after the the bigger strut rod bushing nut.Replaces Ford part # 340460-S
Availability: Used / Wrecking Yard Item
Item #: 26513 -
This clip is the same as a door panel clip with the exception that it does not have the foam spacer. This clip was used on the 1968 XR7 overhead console, 1967 - 1968 xr7 and standard model upper and lower console pads, seat back access panels and several other applications. This original clip holds tighter than the reproduction. We recommend using this used clip over our reproduction for applications like the seat back because the reproductions often do not cut it. Ford part number...
Availability: Used / Wrecking Yard Item
Item #: 11-0354 -
Two or three of these clips were needed per door to mount the padded armrest. Three were used per armrest for a total of six, on 1969-70 Cougar and Mustangs. Two used in 1971-73 on standard Cougars. Sold individually.Replaces Ford part # C6AZ-6224146-B.
Availability: Used / Wrecking Yard Item
Item #: 14-1002 -
Used in multiple applications front and rear lap belts. Inner and outer, marked with a letter "B" in at least three known fonts. 1-3/4 inches long, 1/2 inch shoulder, Torx 50 tool for installation and removal.
Availability: Used / Wrecking Yard Item
Item #: 14-1038 -
Two per car, identified with the letter "D" in three known fonts. This bolt was used in conjunction with a chrome spacer / washer that is also marked with the letter "D". 1-1/2 inches long, 1/4 inch shoulder, use a Torx 50 for installation and removal.
Availability: Used / Wrecking Yard Item
Item #: 14-1244 -
Used on inner and outer rear seat belt bolts, four per car in 1970 -1971 and used only on the inner rears in 72 - 73 due to the addition of rear retractors. Used in conjunction with two red washer / spacers, marked with three known font styles of the letter "A". 1-5/16 inches long, Torx 50 is the tool for installing and removing.
Availability: Used / Wrecking Yard Item
Item #: 23774 -
One per side, 1968 does not use the triangle markings. The letter "D" stamping was in place to aid line workers with correct placement on the car.
Availability: Used / Wrecking Yard Item
Item #: 23783 -
Often you will see minor irregularities in these washers. These would be considered "blems". Two required per car, used only on the re-tractors.
Availability: In-Stock Item
Item #: 41140 -
Replaces Ford Part # 382626-S
Sold individually
Availability: In-Stock Item
Item #: 13066 -
Two or three of these clips were needed per door to mount the padded armrest. Three were used per car for a total of six, on 1969-70 Cougar and Mustangs. Two used in 1971-73 on standard Cougars. Sold individually.Replaces Ford part # C6AZ-6224146-B.
Availability: In-Stock Item
Item #: 31193 -
Reproduction shoulder belt bolt spacer for the 69 - 73 Cougar or Mustang. Does not have markings like the originals. One per side, two per car.
Availability: Used / Wrecking Yard Item
Item #: 11-0459 -
Used single bolt for attaching door and quarter window regulators on any 1969-73 Mercury Cougar or Ford Mustang or Ford anything most likely. Sold individually
Availability: In-Stock Item
Item #: 31883 -
New single bolt for attaching door and quarter window regulators on any 1969-73 Mercury Cougar or Ford Mustang or Ford anything most likely. AMK part. Sold individually
Availability: In-Stock Item
Item #: 33532 -
Reproduction bolts and washers for the shoulder belts on any 1969-73 Mercury Cougar or Ford Mustang. Includes 2 each of the "D" bolts and chrome thick washers. Quality AMK kit F-3563.
Availability: In-Stock Item
Item #: 33533 -
AMK seat belt washer B-13023. 0.46" ID x 1.25" OD zinc flat washer. Sized so that it rides on the shoulder of the seat belt bolts. It allows the retractor to rotate freely between this washer and the head of the seat belt bolt on 1969-73 cars. Two required per car, used only on the re-tractors.
Availability: Rare / NOS Part
Item #: 15542 -
Phosphate & Oil finish. Sold individually. Replaces Ford part #: 378782-S
Availability: In-Stock Item
Item #: 41004 -
This is longer of the two with the + on the bolt head.
Availability: Rare / NOS Part
Item #: 41024 -
Availability: In-Stock Item
Item #: 41025 -
Ford manual transmission flywheel and automatic transmission flex plate mounting bolts. 6 bolts required, sold individually. Replaces Ford part # 378172-S
Availability: In-Stock Item
Item #: 41038 -
Replaces Ford part # 55806-S
Availability: In-Stock Item
Item #: 41008 -
Availability: In-Stock Item
Item #: 41046 -
Used on all small block engines to attach the timing pointer to the timing cover. 1967 - 1973 V-8 engines 289, 302, & 351.
Availability: In-Stock Item
Item #: 41014 -
Reproduction AC Compressor Clutch Bolt for the 1967 - 1973 Mercury Cougar - 1967 - 1973 Ford MustangSold individually
Availability: In-Stock Item
Item #: 41007 -
Reproduction 351W Intake Manifold Bolt for the 1969 - 1973 Mercury Cougar - 1969 - 1973 Ford MustangSold individually
Availability: In-Stock Item
Item #: 41032 -
Reproduction Alternator Pulley Nut for the 1967 - 1973 Mercury Cougar - 1967 - 1973 Ford MustangSold individually
Availability: In-Stock Item
Item #: 41029 -
Replaces Ford part # 351089-S
Zinc (dark silver) finish
Sold individually
Availability: Rare / NOS Part
Item #: 26817 -
Replaces Part # C9OB-3B284. We also have this bolt available in fine thread but only as a used bolt. Four required per car. Sold individually
Availability: In-Stock Item
Item #: 41010 -
part # 370608-S. Used in multiple places on mounting brackets.
Availability: In-Stock Item
Item #: 41031 -
This nut fits onto the strut brace at the front of the car, and not the control arm end.Replaces Ford part # 380517-S
Availability: Rare / NOS Part
Item #: 41012 -
part # 383722-S Pivot bolt for use with the all steel 1970-73 power steering pump mounting bracket. NOS new old stock!
Fits most all Ford 302/351 from 1970-73 with the above described bracket.
Availability: In-Stock Item
Item #: 15524 -
OEM style nut to hold the axle U-bolt to the axle. Fine threaded like originals 7/16-20 grade 5. Will not fit some reproduction U-bolts. Sometimes these are called shock plate bolts. Replaces Ford part # 379244-S
Availability: In-Stock Item
Item #: 26806 -
part# 384114-S100 Sold individually Check out our caliper tips and tricks video below: ...
Availability: In-Stock Item
Item #: 26821 -
Reproduction adjustment cam / bolt for the lower control arms of the Mercury Cougar or Ford Mustang. We also offer this used version as well. These units are sold individually.Ford part # C6OA-3B236-A.
Availability: In-Stock Item
Item #: 41015 -
1/2"-13 x 4 1/2" grade 8 flanged bolt with a phosphate and oil finish. Ford Part # 382486-S.
Availability: In-Stock Item
Item #: 41027 -
replaces Ford part # B-12764
Availability: In-Stock Item
Item #: 41028 -
Replaces Ford part #375381-S Phosphate & Oil Finish
Availability: In-Stock Item
Item #: 41036 -
Fine thread lock nut used in various places on old Fords, including the differential housing, 1967 disc brake assemblies, and more. Replaces Ford part # 34445-S
Availability: In-Stock Item
Item #: 41041 -
Reproduction nut that replaces Ford part # 34033-S. This is the nut that secures the pitman arm to the steering box. Has correct 7/8"-14 threads. Split washer also needed, not included, nut only.
Availability: In-Stock Item
Item #: 41337 -
replaces Ford part # 385161-S
Zinc - Dichromate (yellow - rainbow) finish
Availability: In-Stock Item
Item #: 41162 -
Complete engine mounting hardware kit for the 1970-71 351C 2-barrel engine. See list below to see what is included. Click on images to enlarge.
Availability: In-Stock Item
Item #: 41173 -
AMK engine fastener kit for 1971 Mercury Cougar and Ford Mustang with J or C code 429 Cobra Jet engines. This kit claims to have 136 pieces. This kit additionally fits 1970-71 Ford Torino and Mercury Cyclone and other variants with 429CJ engine.Kit typically includes: fasteners to attach air cleaner, carburetor, crank pulley, distributor / points / condenser / vacuum advance, drain plugs, engine tag, exhaust manifolds, fan / fan clutch, fuel pump, shroud, ignition coil and strap, intake...
Availability: In-Stock Item
Item #: 41163 -
Complete engine mounting hardware kit for the 1970-71 351C 4-barrel engine. See below for list of incuded items. Click on images to enlarge.
Availability: Used / Wrecking Yard Item
Item #: 20116 -
SBVALVCOVER Ford engine blue painted valve cover with "Powered by Ford" embossed in the metal. Correct on 1968-1971 Mercury Cougar and 1968-73 Ford Mustang with 289/302/351W engines. Ford master parts catalog shows a right and left version of this cover those Service Replacement numbers are D2OZ-6582-C & D2OZ-6582-D. *Note - This cover will not work on a 351 Cleveland engine.
Availability: In-Stock Item
Item #: 41331 -
Fits both 8 inch and 9 inch rear ends. Phosphate and oil coated with thread sealer. These are one time only nuts. They should not be reused per Ford. Replaces Ford part #: 371518-S
Availability: In-Stock Item
Item #: 41236 -
Sold indiviually
Phosphate & Oil (gay-black)
Availability: In-Stock Item
Item #: 25897 -
Sold as a pair. Replaces Ford Part # : D0OZ-8052 Check out our video on Radiator and Fan upgrades below:
Availability: In-Stock Item
Item #: 27494 -
New valve cover bolts for all Boss 302, 351C-2V, and 351C-4V Ford engines. These are the AMK bolts with original style Ford assembly line head markings. Correct 7/16 hex head and split tooth captured washer, sold in sets of 16.*Note - Excludes 289/302 and 351W engines (see part number 8316)1/4-20 X 5/8" Hex Head Bolt with Electrolytic Zinc & Wax finishReplaces Ford part number 373071-S.
Availability: In-Stock Item
Item #: 41059 -
Reproduction brake and fuel line clamp kit for Mercury Cougars and Ford mustangs equipped with disc brakes.
Availability: In-Stock Item
Item #: 41060 -
Reproduction brake and fuel line clamp kit for Mercury Cougars and Ford Mustangs equipped with drum brakes.
Availability: Used / Wrecking Yard Item
Item #: 25484 -
Cable length 22.50 inches long. Has clevis and pin on the end for attaching to the throttle pedal assembly. *Note - Used on Cougars prior to 7/10/1972 look at your throttle pedal end.
Availability: Used / Wrecking Yard Item
Item #: 25485 -
Bracket that mounts to firewall for accelerator shaft. 1971-73 Mercury Cougar and Ford Mustang.
Availability: Used / Wrecking Yard Item
Item #: 20530 -
York compressor for air conditioning systems for Mercury Cougar and Ford Mustang. These should be professionally inspected or rebuilt and our compressors have all been in storage for some time. Shipped without pulleys, clutches, or valves. The York compressor is constructed mostly of aluminum and is lighter than the Tecumseh brand compressor by 10 pounds. The York compressors are less common too, subject to availability. We often see part numbers on the York tag (which does not list a Ford...
Availability: Used / Wrecking Yard Item
Item #: 20529 -
Tecumseh compressor for air conditioning systems for Mercury Cougars and Ford Mustangs. These should be professionally inspected or rebuilt and our compressors have all been in storage for some time. These Tecumseh compressors came with a front oil fill plug up until 1967, thereafter, they have a top fill plug. Top fill is the most common, and likely what you will receive, unless you specify the 1967 style with front fill. These units are shipped without pulleys, clutches, or valves. The...
Availability: In-Stock Item
Item #: 20698 -
Brake line rubber grommets for any 1967-73 Mercury Cougar or Ford Mustang. These are the ones that go through the shock towers for the front brake lines. Drum or disc, all the same. Sold as a PAIR. Ford number 373624-S.
Availability: Used / Wrecking Yard Item
Item #: 14-0078 -
Used bolts, and usually new washers. Convertible kit comes with 4 - "A" bolts, 4 "B" bolts, 10 new washers. Kit fits all 1970-73 Mercury Cougar and Ford Mustang convertibles. Coupes or hard tops would include shoulder belt hardware. We will make sure these original seat belt bolts are damage free and rust free. The gold finish will be degraded. There were minor and major changes almost every year. We also have hundreds of used belts and belt sets that we cannot possibly list all of, so give us...
Availability: Used / Wrecking Yard Item
Item #: 23391 -
384543-S8 Power steering pump adjusting spacer for use without air conditioning. For most 1970 - 1973 Mercury Cougar or Ford Mustang with 351C engines. Spacer dimensions: 7/16" I.D. and 1/2" thick.*Note 1970 and later cars with 302 or 351W engines use a 3/4 inch spacer.
Availability: In-Stock Item
Item #: 31878 -
Reproduction throttle cable for the Cougar or Mustang equipped with the 351 engine.Cable length 22.50 inches long. *Note - Used on Cougars prior to 7/10/1972 look at your throttle pedal end.
Availability: In-Stock Item
Item #: 26069 -
This Super Cobra Jet emblem was never used on a Cougar, but is the Cobra Jet emblem used on the Hood Scoop for 1969-1970 Mustangs. It is also an attractive emblem for your custom application. Thanks for the plug Mark!: "My first deal with Don was clear back in the 1980s and I have sent a few people his way and all came away happy. While at his shop on Monday I watched Lin crawl under a convertible, phone in one hand and a tape measure in the other, and measure a cross...
Availability: In-Stock Item
Item #: 19706 -
Good quality but not as good as original in that it is too shiny. Fits Coupe or convertible, left or right. Sold individually. Ford emblem sold separate. Replaces Ford part # D1ZZ-6513298-A
Availability: Used / Wrecking Yard Item
Item #: 25446 -
Good deal for the guy missing a sill plate on a driver. Sold individually.
Availability: In-Stock Item
Item #: 30439 -
Reproduction stainless steel scuff / sill plate. Fits Coupe or convertible, left or right. Sold as a pair. Ford emblem sold separate, find it here. Replaces Ford part # D1ZZ-6513298-A