All Available Parts - 1973 Ford Mustang
Products (Click sub-categories above to ONLY display results for that Sub-Category) 101-200 of 2235
Sorted By:
Availability:
Display Options:
Availability: Used / Wrecking Yard Item
Item #: 32916 -
Used metal dash support brace for all 1971-73 Mercury Cougar and Ford Mustangs. Fastens to the lower flange of the metal dash panel and attaches to the inner cowl, 10 inches long. Replaces Ford part numbers D1ZB-6504672-A.
Availability: In-Stock Item
Item #: 15840 -
Replacement throttle pedal spring for your 71 - 73 Cougar or Mustang. Easy to replace, keeps correct tension on your gas pedal.
Availability: Used / Wrecking Yard Item
Item #: 25382 -
Don't be fooled by knobs with similar part numbers, they have longer shafts and will not work as well on your Mercury Cougar or Ford Mustang application.Ford part # D1ZZ-18830-A, and Ford casting # D1ZA-18A932-AA.*TRIVIA* Did you know that Ford called the inner (balance / tone) radio knobs "discs?"
Availability: In-Stock Item
Item #: 15703 -
Finally, a reproduction radio knob set for your 1971-73 Mercury Cougar or Ford Mustang! These little units are very hard to find in NOS form or good used condition with flawless chrome. Most knobs are peeling bad enough to cut you if you are not being cautious. It's often little detail pieces like these that separate first and second place at car shows.Replaces Ford part #'s D1ZZ-18817-A for the outer (tuner / volume) knob, Ford casting # D1ZA-18822-AA for the outer (tuner / volume) knob....
Availability: Out of Stock
Item #: 26213 -
This kit is similar to the original type mounted in every drivers side door. These OEM style Riv-Nuts will be a challenge to install unless you have the special tool. Almost every body shop will have this rivet gun type of tool but here are a couple of ways to tackle the installation without the correct tool. Hole size is 1/4". Replaces Ford Part #: C7AZ-17696. Check out our video below for more info on mirror installation: Still have riv-nut questions? Here are riv-nut answers! ...
Availability: In-Stock Item
Item #: 10244 -
New mirror glass, for the passenger side on practically any 1969-73 Ford with painted sport mirrors. This is the convex style of mirror, think "Objects in mirror are closer than they appear". Nice fit, exact shape of originals. Dimensions: 4 3/8 x 2 7/8 Do you have questions about installing a passenger side mirror or using Riv-Nuts? Have more questions about installing a passenger side mirror or using Riv-Nuts? Got a mirror lens that flops around in your Sport Mirror every time you hit a tiny...
Availability: In-Stock Item
Item #: 12029 -
Pair of reproduction brackets and rods for the sun visors in the Mercury Cougar or Ford Mustang. *NOTE* These units will also work for the 1971-73 Ford Mustang fastback (sport roof).
Availability: In-Stock Item
Item #: 11822 -
12-point bolt for attaching the steering column coupler to the steering box. Works for all 1967-73 Mercury Cougars and most other Fords, Mercury, and Lincolns. One bolt used for fixed columns, two bolts used on tilt steering columns. Sold individually.
Availability: In-Stock Item
Item #: 27601 -
Reproduction insulator for the lower portion of the steering column found on all 1969-73 Mercury Cougar or Ford Mustangs. Unique slide in plastic bushing or insulator, which slides into the bottom tube of both fixed and tilt columns. Most originals are broken or missing. Two sizes of insulators, please verify year and diameter.1968 tube measures 1 3/8"1969 - 1973 tube measures 1 5/8"*NOTE* WCCC services all FoMoCo tilt and tilt-tilt away steering columns 1967-1979. Our shop rate for this...
Availability: Used / Wrecking Yard Item
Item #: 15-0146 -
Used Release Spring for the 1967 - 1973 Mercury Cougar / 1967 - 1973 Ford Mustang
Availability: Used / Wrecking Yard Item
Item #: 15-0145 -
Used Spring Sleeve Cap for the 1967 - 1973 Mercury Cougar / 1967 - 1973 Ford Mustang
Availability: Used / Wrecking Yard Item
Item #: 15-0181 -
This is a complete shaft. Lower, upper and knuckle. This shaft may have plastic pins broken due to age and handling. It is functional. May have light rust and knuckle will have been tightened if needed.
Availability: Used / Wrecking Yard Item
Item #: 15-0190 -
Used lower steering column shaft for 70 - 73 Cougars and Mustangs with a fixed column. Identified by length, and the round style lower flange. 1968-69 lower flange is slightly smaller with flat sides. Overall length is 16-3/8 inches.
Availability: In-Stock Item
Item #: 32897 -
Used sleeve for fixed steering wheel. Special molded rubber sleeve that holds the bearing in place. Ford part # D1AZ-3518 or E2AZ-3518
Availability: Used / Wrecking Yard Item
Item #: 33445 -
Used lateral or side bracket for mounting the steering column to the instrument panel on any 1972-73 Mercury Cougar or Ford Mustang. Hooped support bracket only, there is also a large main bracket that is also needed. Tilt and fixed steering columns. Bracket also used on 1971 full sized Ford and Mercury cars. Ford part number D1AZ-3B139-A.
Availability: Used / Wrecking Yard Item
Item #: 33446 -
Used bracket for mounting the steering column to the instrument panel on any 1972-73 Mercury Cougar or Ford Mustang. Main bracket only, there is also a hooped support bracket that is also needed. Tilt and fixed steering columns. Bracket also used on 1971 full sized Ford and Mercury cars. Ford part number D1AZ-3676-A.
Availability: Used / Wrecking Yard Item
Item #: 33447 -
Used wiring harness retainer bracket for mounting the steering column bracket, on any 1973 Mercury Cougar or Ford Mustang. Retainer only, many of these are missing. Probably not missed, limited to stock on hand. Basic Ford part number 14A163.
Availability: Used / Wrecking Yard Item
Item #: 33450 -
Used flat headed stove bolt and nut, for attaching the two steering column mounting brackets together. Brackets for mounting the steering column to the instrument panel on any 1972-73 Mercury Cougar or Ford Mustang. Two needed per installation, sold individually. This is a 3/8-16 square neck bolt and nut. Ford part number 384527-S2.
Availability: Used / Wrecking Yard Item
Item #: 33452 -
Used lower steering column mounting bracket at firewall, for any 1971-73 Mercury Cougar or Ford Mustang. Rubber seal will need to be replaced, see related items for rubber seal. Ford part number D1ZZ-65017A50-A.
Availability: Used / Wrecking Yard Item
Item #: 15-0028 -
Correct nut that is designed not to come undone.
Availability: In-Stock Item
Item #: 15-0173 -
Used return spring for any 1970 - 1978 Cougar or Mustang Tilt Column. This spring provides return tension on tilt steering wheels.*NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year.
Availability: In-Stock Item
Item #: 15-0203 -
This extension holds the inner spring tube in place on the 70 - 73 column.Ford part number: D0AA-3790-CW
Availability: In-Stock Item
Item #: 15-0178 -
Used snap ring that is used to hold the bearing on you the steering shaft. This ring was used on 67 - 78 fixed columns and 70 - 78 tilt columns. Not for use on 67 - 69 tilt columns.*NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year. ...
Availability: In-Stock Item
Item #: 15-0179 -
Used retainer / friction clip that replaces broken injected plastic shaft retainers on fixed or tilt steering collapsible columns on most FoMoCo products starting in 1968 and through the 70's. Ford part number C9AZ-3E629-B. *NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year. ...
Availability: In-Stock Item
Item #: 31804 -
This clip goes on the upper end of your column and keeps your steering shaft from moving around when you pull up on your steering wheel.
Spotlight!
Featured!
Availability: In-Stock Item
Item #: 32067 -
Reproduction 3D printed retainer / friction clip that replaces broken injected plastic shaft retainers on fixed or tilt steering collapsible columns on most FoMoCo products starting in 1968 and through the 70's. These installs on the upper piece of what Ford called the Steering Column Shaft Assembly, also known as the inner steering column collapsible shaft. The Steering Column Shaft Assembly is the 2 piece shaft that connects the steering wheel to the rag joint. The upper...
Availability: In-Stock Item
Item #: 30663 -
Availability: Ships Direct from Supplier (Except International)
Item #: 11992 -
Reproduction reinforcement plate designed to weld onto the lower control arms. Sold individually, we are not sure that you would want to even buy one of these. They don't fit very well, and are not contoured to any lower control arm on the market. You will be bending these to fit, prior to welding. *Note - This is a non-returnable item.
Availability: Used / Wrecking Yard Item
Item #: 25508 -
D2OZ-7976-A Aluminum bell housing, sometimes called a converter housing in the Ford shop manual. 1972 - 1973 Mercury Cougar and Ford Mustang with 351 engine and automatic FMX transmission, code X on your door data plate tag. Ford master part number D2OZ-7976-A.
Availability: Used / Wrecking Yard Item
Item #: 16-0017 -
Used FMX transmission tail shaft or housing extension as Ford called them in the Master Parts Catalog. Fits all 1969-73 Mercury Cougar and Ford Mustang cars with transmission code X on the door tag. Cast aluminum construction. D2ZP-7A040-A version also available, we have a good supply of the updated 1972 version. The overall length of this housing is 12 7/8", which was also used on 1969 Fairlanes and Torinos. This housing will not fit full sized Ford Mercury cars that have an FMX,...
Availability: In-Stock Item
Item #: 41349 -
1967-68 XR7 over head console pad clip. Two needed per car. Sold individually # C3AB-63519A16
Featured!
Availability: In-Stock Item
Item #: 12140 -
NOTE: Some modification required to fit Cougars! These are actually 69-70 Mustang wheel lip mouldings, which have a different shape / contour. However, with a bit of massaging they can be made to fit the 71 - 73 Cougar. They are the closest alternative we have found that fits and looks reasonably good for much less than restored originals. Check out our video below, showing how easy it is to install these mouldings on a Cougar ...
Availability: In-Stock Item
Item #: 11517 -
Restored four piece aluminum rear window moulding / trim set correctly restored with an anodized and a bright dip finish and polished to a very high luster.Ford part #s D1ZZ-6542405-A, D1ZZ-6542404-A, D1ZZ-6542430-A, D1ZZ-6542431-A.
Availability: Used / Wrecking Yard Item
Item #: 11518 -
Good used four piece aluminum rear window moulding / trim set with some dings and or minor scratches. Ready to install on your Cougar as is, or polish them to be installed on a daily driver. These original FoMoCo mouldings are far superior to the off shore reproductions that do not fit well and have an incorrect color to them. Ford part #s D1ZZ-6542405-A driver side (left hand) lower, D1ZZ-6542404-A passenger side (right hand) lower, D1ZZ-6542430-A passenger side upper, and D1ZZ-6542431-A...
Availability: Used / Wrecking Yard Item
Item #: 11519 -
Our used passenger (right hand) side upper rear aluminum window mouldings / trim will have light scratches and minor dings. These are suitable for restoration or for a lower quality daily driver. We will not send you kinked or gouged trim as it is not feasible to restore heavily damaged trim. Ford part # D1ZZ-6542430-A.
Availability: Used / Wrecking Yard Item
Item #: 11520 -
Our used passenger (right hand) side lower rear aluminum window mouldings / trim will have light scratches and minor dings. These are suitable for restoration or for a lower quality daily driver. We will not send you kinked or gouged trim as it is not feasible to restore heavily damaged trim. Ford part # D1ZZ-6542404-A.
Availability: Used / Wrecking Yard Item
Item #: 11521 -
Our used driver (left hand) upper rear aluminum window mouldings / trim will have light scratches and minor dings. These are suitable for restoration or for a lower quality daily driver. We will not send you kinked or gouged trim as it is not feasible to restore heavily damaged trim. Ford part # D1ZZ-6542430-A. ...
Availability: Used / Wrecking Yard Item
Item #: 11522 -
Our used driver (left hand) lower rear aluminum window mouldings / trim will have light scratches and minor dings. These are suitable for restoration or for a lower quality daily driver. We will not send you kinked or gouged trim as it is not feasible to restore heavily damaged trim. Ford part # D1ZZ-6542430-A.
Availability: Used / Wrecking Yard Item
Item #: 15730 -
Our core passenger (right hand) upper rear aluminum window mouldings / trim will have some scratches and dings and are suitable for restoration. We will not send you kinked or gouged trim as it is not feasible to restore heavily damaged trim.Ford part # D1ZZ-6542430-A.
Availability: Used / Wrecking Yard Item
Item #: 15793 -
Our core driver (left hand) upper rear aluminum window mouldings / trim will have some scratches and dings and are suitable for restoration. We will not send you kinked or gouged trim as it is not feasible to restore heavily damaged trim.Ford part # D1ZZ-6542431-A.
Availability: Used / Wrecking Yard Item
Item #: 15794 -
Our core passenger (right hand) lower rear aluminum window mouldings / trim will have some scratches and dings and are suitable for restoration. We will not send you kinked or gouged trim as it is not feasible to restore heavily damaged trim.Ford part # D1ZZ-6542404-A.
Availability: Used / Wrecking Yard Item
Item #: 15795 -
Our core driver (left hand) lower rear aluminum window mouldings / trim will have some scratches and dings and are suitable for restoration. We will not send you kinked or gouged trim as it is not feasible to restore heavily damaged trim.Ford part # D1ZZ-6542405-A.
Availability: Used / Wrecking Yard Item
Item #: 15796 -
Our core aluminum rear window mouldings / trim will have scratches and dings and are suitable for restoration. This kit consists of one driver side (left hand) upper, one passenger side (right hand) upper, one driver side lower, and one passenger side lower core window moulding / trim. These original FoMoCo mouldings are far superior to the off shore reproductions that do not fit well and have an incorrect color to them. We will not send you kinked or gouged trim as it is not feasible to...
Availability: Out of Stock
Item #: 13095 -
Restored pair of windshield mouldings / trim for the Mercury Cougar or Ford Mustang coupe. These units have been restored using the correct bright dip anodize and will look better than NOS. Ford part # driver side D1ZZ-6503145-A, passenger side D1ZZ-6503144-A.
Availability: Used / Wrecking Yard Item
Item #: 13096 -
Used pair of windshield mouldings / trim for the Mercury Cougar or Ford Mustang coupe. The bright dip anodize has worn off of these and they may have some very fine scratches, but they will not be dented or have any heavy scratching. Suitable for your daily driver or for restoration.Ford part # driver side D1ZZ-6503145-A, passenger side D1ZZ-6503144-A.
Availability: Used / Wrecking Yard Item
Item #: 13101 -
Core pair of windshield mouldings / trim for the Mercury Cougar or Ford Mustang coupe. These units may have some dings, scratches and will be dull. A cheap and easy fix for your cat or pony that may have missing windshield trim. Ford part # driver side D1ZZ-6503145-A, passenger side D1ZZ-6503144-A.
Availability: In-Stock Item
Item #: 13094 -
Restored passenger side (right hand) windshield moulding / trim for the Mercury Cougar or Ford Mustang coupe. This unit has been restored using the correct bright dip anodize and will look better than NOS. Ford part # D1ZZ-6503144-A.
Availability: Used / Wrecking Yard Item
Item #: 13097 -
Used passenger side (right hand) windshield moulding / trim for the Mercury Cougar or Ford Mustang coupe. The bright dip anodize has worn off of this unit and it may have some very fine scratches, but will not be dented or have any heavy scratching. Suitable for your daily driver or for restoration. Ford part # D1ZZ-6503144-A.
Availability: Used / Wrecking Yard Item
Item #: 13100 -
Core passenger side (right hand) windshield moulding / trim for the Mercury Cougar or Ford Mustang coupe. This unit may have some dings, scratches and will be dull. A cheap and easy fix for your cat or pony that may have missing windshield trim. Ford part # D1ZZ-6503144-A.
Availability: Used / Wrecking Yard Item
Item #: 13099 -
Core driver side (left hand) windshield moulding / trim for the Mercury Cougar or Ford Mustang coupe. This unit may have some dings, scratches and will be dull. A cheap and easy fix for your cat or pony that may have missing windshield trim. Ford part # D1ZZ-6503145-A.
Availability: Used / Wrecking Yard Item
Item #: 13098 -
Used driver side (left hand) windshield moulding / trim for the Mercury Cougar or Ford Mustang coupe. The bright dip anodize has worn off of this unit and it may have some very fine scratches, but will not be dented or have any heavy scratching. Suitable for your daily driver or for restoration. Ford part # D1ZZ-6503145-A.
Availability: Ships Direct from Supplier (Except International)
Item #: 15567 -
This direct replacement is the 2-1/4 inch H pipe only and is for any 1971-73 Mercury Cougar or Ford Mustang with stock cast iron exhaust manifolds. These units are manufactured right here in the good old USA from 2-1/4 inch aluminized pipes and made from an original 1971 Cougar and Mustang with either the H, M, or Q code 351C engine. We also sell OEM style dual exhaust systems that include the H pipe, mufflers, and tail pipes.*NOTE* Will not fit 351 Windsor, 1970 351 Cleveland engines. Please...
Availability: Ships Direct from Supplier (Except International)
Item #: 15571 -
This direct replacement is the 2 inch Y pipe only with 2-1/4 intermediate pipe outlets and is for any 1971-73 Mercury Cougar or Ford Mustang with stock cast iron exhaust manifolds. These units are manufactured right here in the good old USA from 2 inch aluminized pipes and made from an original 1971 Cougar and Mustang with the 351C 2V engine. We also sell OEM style dual exhaust systems that include the H pipe, mufflers, and tail pipes.*NOTE* Will not fit 1970 351 Cleveland engines. Please...
Availability: Used / Wrecking Yard Item
Item #: 25430 -
Housing overall width - 55-3/4 inches flange to flange. Spring perches are 43 inches apart on center. Bare housing with proper axle pad spacing for all 1971-1973 Cougars. Over-sized shipping length.Axles needed: Passenger side - 32 inches long, Driver side 28 inches long.
Availability: Used / Wrecking Yard Item
Item #: 25080 -
Right side axle, 28 spline 31-7/8 inch length. Ships with used bearing, bearing retainer plate, and 5 pressed in wheel studs. *Note 429 CJ equipped Cougars came with heavy duty 31 splined axles.
Availability: Used / Wrecking Yard Item
Item #: 25081 -
Left side axle, 28 spline 27-13/16 inch length. Ships with used bearing, bearing retainer plate, and 5 pressed in wheel studs. *Note 429 CJ equipped Cougars came with heavy duty 31 splined axles.
Availability: Used / Wrecking Yard Item
Item #: 20542 -
Since we always claim to have parts nobody else does... This welds to the bottom side of the car just above the differential. When the rear suspension bottoms out, this is the plate the rubber snubber / bumper (mounted on the front on top of the dif.) makes contact with.
Availability: Used / Wrecking Yard Item
Item #: 25078 -
Also called a pumpkin, 2.75:1 open ratio. Check your door tag under "Axle".
1968 code 1 1969-73 code 2
Availability: Used / Wrecking Yard Item
Item #: 23913 -
Mounts over rear axle ends into the body/frame, two required per car, this is the more pointed Christmas tree shaped version.Ford part # C6AZ-4730
Availability: Used / Wrecking Yard Item
Item #: 25079 -
D0OZ-4204-9A300 1968-1973 9 Inch Third Member - Used
Also called a pumpkin, 3.00:1 open ratio. These 3rd members will have the fill plug.
Check your door tag under "Axle".
Availability: Used / Wrecking Yard Item
Item #: 25429 -
NOTE! When we ship a rear end, we will remove the third member and ship it in a separate box. Some assembly will be required. Housing overall width - 55-3/4 inches flange to flange. Spring perches are 43 inches apart on center. Overall width measured from faces of axles, not the tips. All 1971-73 have the same overall width of 61 inches. Rear axle assembly - Housing, Axles, brake backing plates, and third member. As removed from a 1971-73 West Coast Cougar organ donor car. We...
Availability: Used / Wrecking Yard Item
Item #: 25431 -
D3ZZ-4730-A Rubber bumper that mounts to the metal axle snubber on Ford nine inch rear ends on 1973 Mercury Cougar and Ford Mustangs. Good used part with solidly mounted metal threaded stud. Pinion bumper.
Availability: In-Stock Item
Item #: 41343 -
#373820-S Copper washer for attaching the 8 inch or 9 inch third members to the axle housings. Steel washers will leak, made from copper which is a soft metal and seals under the attaching nuts. Copper washers like the OEM Ford installed washers. Takes 10 washers total for both 8 and 9 inch rear ends. *Tip - It is a good idea to inspect or replace your old washers, many times they have tool marks from the housing or nuts that cause small troublesome leaks.
Availability: Used / Wrecking Yard Item
Item #: 25438 -
This 2 degree wedge properly sets the pinion angle for the drive shaft.The Mercury Parts Catalog states that this part is installed "As Required".Orientation: Narrow end towards the front of the car.
Availability: Out of Stock
Item #: 25437 -
This 1.5 degree wedge properly sets the pinion angle for the drive shaft.The Mercury Parts Catalog states that this part is installed "As Required".Sold individually, two required per vehicle.Orientation: Narrow end towards the front of the car.
Availability: Used / Wrecking Yard Item
Item #: 25436 -
This 1 degree wedge properly sets the pinion angle for the drive shaft.The Mercury Parts Catalog states that this part is installed "As Required".Orientation: Narrow end towards the front of the car.
Availability: Ships Direct from Supplier (Except International)
Item #: 20509 -
Limited slip 8 inch Ford third member rebuilt with all new parts. Factory new 4 pinion Trac-Loc unit, new Motive ring and pinion gears, new Timkin bearings, new crush sleeve, new bolts, and new seal. Rebuilt using 1967 and newer two rib style case, with oil fill plug, and standard 1310 yoke. There are various ring and pinion (gear) ratios and axle splines available, if you are unsure of what you need it is best to call (503) 463-1130 for your order. This is a drop ship item. *Note - New...
Availability: Ships Direct from Supplier (Except International)
Item #: 20510 -
Limited slip 8 inch Ford third member rebuilt with all new parts. Factory new Eaton True-Trac 8 pinion clutchless traction locking unit, Richmond ring and pinion gear, Timkin bearings, crush sleeve, bolts, and seal. Rebuilt using 1967 and newer two rib style case, with oil fill plug, and standard 1310 yoke. Ships with direction sheet and bottle of Ford Motorcraft friction modifier additive for the rear end gear oil. For use with 28 splined axles, but can be custom...
Availability: Ships Direct from Supplier (Except International)
Item #: 19802 -
Limited slip 9 inch Ford third member rebuilt with all new or reconditioned parts. Rebuilt 4 pinion Trac-Loc unit, with new clutches, steels, Richmond ring and pinion gears, Timkin bearings, crush sleeve, bolts, and seal. Rebuilt using standard 9 inch cases with oil fill plug. Ships with direction sheet and bottle of Ford Motorcraft friction modifier additive for the rear end gear oil. For 28 or 31 splined axles. This unit was used in Cougars and Mustangs, but also any other Fords...
Availability: Ships Direct from Supplier (Except International)
Item #: 19801 -
Limited slip 9 inch Ford third member rebuilt with all new parts. New 4 pinion Trac-Loc unit, Richmond ring and pinion gears, Timkin bearings, crush sleeve, bolts, and new a seal. Rebuilt using the standard 9 inch case, with oil fill plug. Ships with direction sheet and bottle of Ford Motorcraft friction modifier additive for the rear end gear oil. For 28 or 31 splined axles. This unit is for 1967-73 Cougars and Mustangs, but it works for any other Mercurys or Fords with a 9 inch...
Availability: Ships Direct from Supplier (Except International)
Item #: 19803 -
Limited slip 9 inch Ford third member rebuilt with all new parts. New Eaton True-Trac 8 pinion clutchless traction locking unit, Richmond ring and pinion gear, Timkin bearings, crush sleeve, bolts, and seal. Rebuilt using 1967-1973 standard 9 inch case with oil fill plug. For 28 or 31 splined axles. This unit is for 1967-73 Cougars and Mustangs, but can be used on any other Ford or Mercury with a 9 inch drop out center section. Because of all the various ring and pinion...
Availability: Ships Direct from Supplier (Except International)
Item #: 19798 -
Limited slip nodular 9 inch Ford third member rebuilt with all new parts. New 4 pinion Trac-Loc unit, Richmond ring and pinion gears, Timkin bearings, selective size sleeve, bolts, and seal. Rebuilt using a nodular 9 inch case with oil fill plug. Ships with direction sheet and bottle of Ford Motorcraft friction modifier additive for the rear end gear oil. For 28 or 31 splined axles. This unit is for 1967-73 Cougars and Mustangs, but it can also be used for any other Ford or...
Availability: Ships Direct from Supplier (Except International)
Item #: 19800 -
Limited slip nodular 9 inch Ford third member rebuilt with all new parts. New Eaton True-Trac 8 pinion clutchless traction locking unit, Richmond ring and pinion gear, Timkin bearings, selective size sleeve, bolts, and seal. Rebuilt using a 1967-1973 nodular 9 inch case with oil fill plug. For 28 or 31 splined axles. This unit is for 1967-73 Cougars and Mustangs, but can be used in any other Ford or Mercury with a 9 inch drop out center section. Because of all the...
Availability: Ships Direct from Supplier (Except International)
Item #: 19797 -
Limited slip, nodular 9 inch Ford third member rebuilt with all new or reconditioned parts. Used modern design Detroit Locker unit, new Richmond ring and pinion gear, new Timkin bearings, new selective size sleeve, new bolts, and new seal. Rebuilt using 1967-1973 nodular 9 inch cases with oil fill plug, for 28 or 31 splined axles. This unit was used in 1967-73 Cougars and Mustangs, but it also came in any other Fords or Mercurys with a 9 inch drop out center section....
Availability: Used / Wrecking Yard Item
Item #: 16-0049 -
31 Spline transmission slip yoke for all 1969 351-2v/4v and 1970-1973 351-2v FMX cars. *Excludes 351C-4v and 351CJ engines.
Availability: In-Stock Item
Item #: 41624 -
Keep in mind these will work on the Cougar but are designed for the Mustang which has a lower maximum spring travel. If your Cougar is lowered in the rear by an inch or more these will be spot on.Sold individually
Availability: In-Stock Item
Item #: 10577 -
[No Description Provided]
Availability: In-Stock Item
Item #: 15-0157 -
Locking pawl catch pin and locking pawl pin for your 70-73 Lincoln - Mercury - Ford tilt steering columns. This is an improved reproduction with cir-clips to prevent movement, avoiding damage to you locking pawl. These shafts are notorious for working their way out of place with normal use. Once the pin works its way out the locking pawl will not be aligned with the teeth and the cast part will break under pressure. Upgrading to these parts can avoid several hundred dollars in damage. These...
Availability: Used / Wrecking Yard Item
Item #: 15-0159 -
This linkage fits between the gear at the bottom of the key lock and rod that goes to the ignition switch on the fixed column.*NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year. Ford part number D0AA-3E715-D
Availability: In-Stock Item
Item #: 15-0204 -
Locking pawl pin for your 70 - 79 tilt steering column for all Lincoln - Mercury - Ford products. This is an improved reproduction with cir-clips to prevent movement, avoiding damage to your locking pawl. These shafts are notorious for working their way out of place with normal use. Once the pin works its way out the locking pawl will not be aligned with the teeth and the cast part will break under pressure. Upgrading to this part can avoid several hundred dollars in damage. This precision...
Availability: In-Stock Item
Item #: 45631 -
Stainless trim that affixes to the leading edge of the quarter window on coupe or convertible. Does not come with weather strip.
Availability: In-Stock Item
Item #: 30405 -
Reproduction four piece aluminum rear window moulding / trim set for the 71 - 73 Cougar or Mustang. Customers have mentioned that these are very hard to install on the Cougar. Ford part #s D1ZZ-6542405-A, D1ZZ-6542404-A, D1ZZ-6542430-A, D1ZZ-6542431-A.
Availability: In-Stock Item
Item #: 31902 -
Reproduction pair of windshield mouldings / trim for the Mercury Cougar or Ford Mustang coupe. Replaces Ford part #'s driver side D1ZZ-6503145-A, passenger side D1ZZ-6503144-A.
Availability: In-Stock Item
Item #: 45613 -
Stainless trim that affixes to the leading edge of the quarter window on coupe or convertible.
Availability: Used / Wrecking Yard Item
Item #: 10173 -
Used in 1971-73 Mercury Cougars and Ford Mustang for the stop lamps, located under the dash on a panel next to the fuse block.15amp circuit breaker. It is 1.25" x 13/16" and has a single green dot. Box is marked FASCO, 15AMP 12V, and made in the U.S.A. Integrated mounting tab for this application. Ford part number D1MY-14526-A. *NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the...
Availability: Used / Wrecking Yard Item
Item #: 12970 -
Tested and working relay for the 'headlights - on' reminder. Relay with mounting tab for 1971-73 Mercury Cougar and Ford Mustang. This relay controls a buzzer as a reminder to turn off the headlights or remove the key, when the door is opened.Replaces Ford part number D1AB-10C838-A or D1AZ-10C838-A.
Availability: Out of Stock
Item #: 13000 -
New axle bearing for any 8 or 9 inch Ford rear end with 28 splined axles. Common on all Mercury Cougar and Ford Mustang with V-8 engines. Excludes 31 splined axles as found on Boss and Cobra Jet cars.These should be professionally installed with a bearing press.
Availability: Out of Stock
Item #: 13002 -
New outer axle gasket for any 8 or 9 inch Ford rear end with 28 splined axles. Common on all Mercury Cougar and Ford Mustang with V-8 engines. Excludes 31 splined axles as found on Boss and Cobra Jet cars. One required per side, two per car.
Availability: In-Stock Item
Item #: 13060 -
Rear axle vent bolt for the 67 - 73 Cougar or Mustang. This bolt serves a dual purpose, as it also holds the brake line bracket in place on the axle tube.
Availability: Used / Wrecking Yard Item
Item #: 30048 -
Used pinion yoke for an 8 inch rear end on any 1967-68 Mercury Cougar or 1967-73 Ford Mustang. 25 splines Ford says it is for a 1260 U-Joint. Part cleaned for pictures, used parts shipped the way they come off of the cars. Shipped bare, no hardware included.Ford part number C3OZ-4851-A.
Availability: In-Stock Item
Item #: 31555 -
Nuts and washers for attaching the rear differential carrier or pumpkin or third member to the rear axle housing. Correct for all 1969-73 Mercury Cougar and 1969-73 Ford Mustang. 8 inch or 9 inch third members, all the same.
Availability: In-Stock Item
Item #: 31656 -
New pinion seal for any 8 inch third member found in 1967-73 Ford and Mercury cars. 1967-68 Mercury Cougar and all years of Mustang with 8 inch drop out rears.
Availability: In-Stock Item
Item #: 41430 -
Reproduction anti-squeak pad for the leaf springs found on the Mercury Cougar or Ford Mustang. This little unit goes between each individual leaf spring and prevents metal to metal contact. These are sold individually and eight are required per car. Our reproduction leaf springs come with this pad pre-installed. Replaces Ford part # C0AA-5586.
Availability: In-Stock Item
Item #: 41270 -
This is the bushing that Ford lists as the REAR stabilizer end link bushing, but it works for both front and rear. Smaller image shows a comparison of the NOS(Left) and Repro (right). SOLD INDIVIDUALLY. Replaces Ford Part #: KC-55490-A.
Availability: In-Stock Item
Item #: 13929 -
This is the bushing that Ford lists as the REAR stabilizer end link bushing, but it works for both front and rear. Smaller image shows a comparison of the NOS(Left) and Repro (right). SOLD AS SET OF 8. Replaces Ford Part #: KC-55490-A.
Availability: In-Stock Item
Item #: 11324 -
These coarse thread nuts have an integrated lock washer with serations for the Mercury Cougar or Ford Mustang. They will ONLY work with the U-Bolts used in conjunction with the lowering kits. The thread size is 7/16"-14. *NOTE* Eight of these are required per car and are sold individually.
Availability: In-Stock Item
Item #: 16802 -
Reproduction leaf spring center bolt for your 67 - 73 Mercury Cougar.
Availability: Used / Wrecking Yard Item
Item #: 25560 -
All applications, attaches the drive shaft U-Joint to rear end pinion yoke. Sold in pairs, complete with nuts. Perfect used. Ford Part #: C1AZ-4529-A or D3AZ-4529-A.
Availability: Used / Wrecking Yard Item
Item #: 25543 -
Application all 1967-1968 289/302 engines with C4. 1967-1973 small block V-8 with 3 or 4 speed manual transmissions. Features 28 splines. Some have a casting number of C5AW-4888-A.Excludes Hi-performance V-8's such as Boss 302, 390, 428CJ, and C-6 / FMX transmissions.
Availability: In-Stock Item
Item #: 41124 -
Replaces Ford Part # C1AZ-4529-A Sold individually. All applications, attaches the drive shaft U-Joint to rear end pinion yoke. 5/16 Inch Diameter #24 thread for 1 1/8 inch Bearing Caps.