Home > 1969 Mercury Cougar
All Available Parts - 1969 Mercury Cougar
Products (Click sub-categories above to ONLY display results for that Sub-Category) 5201-5300 of 5302
Sorted By:
Availability:
Display Options:
Availability: Out of Stock
Item #: 31161 -
Reproduction door glass run. This is the metal tube that the windows go up and down on, sometimes called an elevator shaft. Right side door only. Application 1969-70 Mercury Cougar and Ford Mustang including Mach 1. Two per door. Front is same as rear. Check out our used door glass runs, original Ford and lower priced. NOTE: To get the orientation correct on these rods, lay the base of it flat on a table - the rod will lean toward the rear of the door. Ford part # C9ZZ-6521546-A. Do...
Availability: Out of Stock, On Order
Item #: 12177 -
Window stop bolt for 69-70 Cougars. Each stop needs 2 bolts
Availability: Out of Stock
Item #: 11-0194 -
Grade B, Rear stop bracket for passenger side door window. Stops the window in the up position. Application passenger side door glass 1969-70 Mercury Cougar and Ford Mustang including Mach 1. One per door. Plate and bolts, not included. Plan on replacing the felt, and most likely the rubber dipped section will be cracked. Please see related listing for plate only or complete stop bracket assembly. Ford part # C9ZZ-65222A54-A. Do you have questions about Glue-In vs Bolt-In glass? How...
Availability: Out of Stock, On Order
Item #: 15747 -
Used under dash wiring harness repair plug and pigtail to the windshield wiper switch for the Mercury Cougar XR7. It was also used on the Standard model after 3/3/1969. This is part of the 14401 main under dash wiring harness.
Availability: Out of Stock
Item #: 11-0171 -
Used drivers side or left door window regulator for all 1969-70 Mercury Cougar and Ford Mustangs with glued in door glass. Good used regulators that we inspect for operation. We suggest lubricating with suitable grease on all of the moving parts and the actual regulator mechanism during the installation. Comes complete with spring, white plastic rollers, and captured steel bushing with clip. The regulator used on the bolt in glass, which became standard soon after the 1970 model year began, is...
Availability: Out of Stock
Item #: 20617 -
Used passenger side (right hand) grade "A" clear door glass for the Mercury Cougar or Ford Mustang coupe or convertible. This item does not include any of the window trim so save yours for reuse. This unit will not have the faint green tint like the SUN-X factory tinted glass. Very good used door glass with no deep scratches (multiple faint scratches and water spots often will be present). Not perfect but the best you could expect to find from a 50 year old plus parts car and will of course be...
Availability: Out of Stock
Item #: 15741 -
Used under dash wiring harness repair plug and pigtail to the ignition switch for the Mercury Cougar XR7. This is part of the 14401 main under dash wiring harness.
Availability: Out of Stock
Item #: 24847 -
Factory 15/16" sway bar for all GT-E 427-4V, 428 Cobra Jets, 428Super Cobra Jets, and Boss 302 Eliminators. Factory identified with a single 'Green' and single 'Yellow' paint stripe. We also carry the spacer plates separately. *Trivia - 1970 was the first year that a rear sway bar was available on a Cougar. A 5/8 inch rear sway bar would have been included with the competition handling package in 1970. This factory used front sway bar, does not include any mounting brackets or end link...
Availability: Out of Stock
Item #: 24486 -
428CJ engines with C6 automatic transmissions. Shaft diameter 3-1/2 inches. Length 49-41/64 inches, measured on U-joint centers. Used and 'as balanced' from the factory. Ask about slip yokes. Shipping is oversized due to length.
Availability: Out of Stock
Item #: 24845 -
Used factory 3/4 inch sway bar for the FE 390 engine of 1969. This bar was factory identified with a single 'Yellow' and a single 'Blue' paint stripe. This bar is not to be confused with the Competition Handling Package sway bar which was optional on any 1969 Cougar. This factory used front sway bar does not include any mounting brackets or end link kits. Ford part # C9ZZ-5482-C.
Availability: Out of Stock, On Order
Item #: 26668 -
Tall version 1" thick and can be used with performance springs to bring the car to a stock ride height. Sold as a Pair. Replaces Ford Part #: C4DZ-5415-A.
Availability: Out of Stock, On Order
Item #: 31550 -
Made from polyurethane, a bit more rigid and stiffer than our rubber insulators. Sold individually. Two required per vehicle. These are the coil spring insulators available from most Mustang/Cougar suppliers. Replaces Ford Part #: C4DZ-5415-A.
Availability: Out of Stock, On Order
Item #: 11794 -
This reproduction universal joint fits the differential end of the drive axle and is used on all Mercury Cougars or Ford Mustangs equipped with the 289, 302, 351 Windsor as well as most 351 Clevelands (see chart). Includes a grease fitting for extended life. 3.25" span cups are 1.12" and 1.00" diam. Replaces Ford part # C3AZ-4635-F.
Availability: Out of Stock
Item #: 24842 -
NOTE! When we ship a rear end, we will remove the third member and ship it in a separate box. Some assembly will be required. Housing overall width - 54-1/4 inches flange to flange. Spring perches are 43 inches apart on center. Overall width measured from faces of axles, not the tips. All 1967-70 have the same overall width of 59-1/2 inches. Rear axle assembly - Housing, Axles, brake backing plates, and third member. As removed from a 1969 West Coast Cougar organ donor car. We recommend a...
Availability: Out of Stock
Item #: 24174 -
1967 - 1969 390-4V engines with 3 or 4 speed manual transmissions. 1969 - 1970 Boss 302 Eliminator 4 speeds. 1970 M-code with 3 or 4 speed manual transmissions. Shaft diameter 3 inches, length 53-1/32" measured on U-joint centers. Used and 'as balanced' from the factory. Ask about slip yokes. Shipping is oversized due to length.
Availability: Out of Stock
Item #: 24484 -
1968 - 1970 428CJ Drive shaft - Used All 428CJ's with 4 speed manual transmissions. Shaft diameter 3 inches, length 53 inches measured on U-joint centers. Used and 'as balanced' from the factory. Ask about slip yokes. Shipping is oversized due to length.Ford part # C8WY-4602-A.
Availability: Out of Stock
Item #: 16-0047 -
Application; 390, 427, 351CJ, 428CJ, and 429CJ all with C6 transmission. 428CJ and 429CJ 4 speed transmissions. 1970 351C-4v with FMX.U-joint size 1330, overall length 8-3/4 inches.
Availability: Out of Stock
Item #: 14475 -
Leaf Springs shipping time is 8-12 weeks.
All of our springs are intended to return the car to factory height. Because of that, installing new springs will almost always increase the height of the rear of the car, as the factory leafs sag over the years. The competition springs will sit slightly lower than standard springs, somewhere between 1/2" and 1" lower. The competition springs cause the car to have a slightly lower the center of gravity and the competition springs are a stiffer spring,...
Availability: Out of Stock
Item #: 16234 -
Used rear leaf spring retainer for 1967 -73 Mercury Cougar with competition handling or GT suspensions. Additionally it fits 1966-71 Mercury Comet / Montego / Cycolne, 1966-71 Ford Fairlane / Torino, all with HD or GT suspensions. Identified with a stamped number "2" on the top. The inside height is 1-29/32 or 1.91 inches. Sold individually, one for each side for a total of 2 per car. Bead blasted for pictures, most will ship 'as removed'. This suspension part never came painted, there will be...
Availability: Out of Stock
Item #: 41364 -
Sold individually. Has correct flattened area at top. Competition handling size, measures 7" from inner radius to end of threads. Thread size 7/16-20". Does not include the OEM style nuts, those are an optional addon. Replaces Ford Part #: C6OA-5705-C
Availability: Out of Stock
Item #: 24593 -
The 69-73 looks the same as the earlier version once installed but the casting number will read C3AA-4906-C on the early unit and C9OA-4906-A on the 1969-73 version. We have found a few rubber bumpers marked D3Z... very few. See other listing for that one..
Availability: Out of Stock
Item #: 31253 -
Good used axle vent nipple or tube. This vent tube screws into the top of the rear axle and is a breather / vent to equalize the pressure inside the axle tube. Fits both 8 inch and 9 inch rear axles. Fits Mercury Cougar and Ford Mustang 1967-73. A (5/16" inside diameter) rubber hose about 18-1/4 inches long attaches to the nipple. Has a very tiny diameter hole inside, about 0.062". Needs to be kept clear to work properly. Also see the reproduction version from AMK. Concours hose kit with...
Availability: Out of Stock
Item #: 25243 -
Bracket that holds the throttle cable for the G code Boss 302 Cougar Eliminators. This is a 1970 part number, it is possible that the 1969 bracket may be either different or had a C9ZZ-9741-? part number. Will update when we verify, comments welcome. 1970 Ford part number listed as D0ZZ-9741-A.
Availability: Out of Stock
Item #: 32702 -
Low fuel option electrical relay. Stamped C6AF-10A968-A, Ford engineering number C5AZ-10A968-C. This relay was used on 1965-70 Ford and Mercury full sized cars, 1968-70 Torino/Cyclone/Montego/Fairlane, along with 1967-70 Mercury Cougar and Ford Mustang with that low fuel option. New Old Stock relay. *Note - Generally this will not solve your low fuel indicator problems. The low fuel indicator failure is almost always due to a failed thermistor. The thermistor is located on the fuel sending...
Availability: Out of Stock
Item #: 31059 -
Clean cores are required for this service, cores that are turned in for this service that are kinked, heavily pitted or mouldings with several holes drilled into them are not worth restoring. That being said, often all of the gravel pitting usually found at the front cannot completely be removed as it would result in a product that will be too thin. Keep in mind that because these are restored mouldings, they will not have the black strips in place and will need to be painted on."...Don -...
Availability: Out of Stock
Item #: 13154 -
NOS seat belt warning light relay for most Ford Lincoln and Mercury cars starting in 1967 until sometime in 1972 when a Motorcraft version of this exact relay was produced. This is a timed relay that allows several seconds of illumination to your seat belt warning light. Ford Part number C7AB-10B924-B1, Ford Service part number D1AZ-10B924-A or D2AB-10B924-AA.
Availability: Out of Stock
Item #: 27302 -
*NOTE* Due to the difficulty in obtaining 69 aluminum trim we no longer sell these without first having you send us your cores. Keep in mind we pay well for quality 69 hood lip mouldings. Do not contact us with pretzel shaped parts, parts you have attempted to fix or flattened out parts. We need trim parts showing only minor dings / dents, scratches and dullness. Decent used trim part that would look good on a daily driver. This purchase requires that you...
Availability: Out of Stock
Item #: 15441 -
Kit comes with 4 metal clips, Ford part number C9WY-6510198-A and 10 plastic clips, Ford part number C9WY-6510182-A. Pictured is a complete set of 1969 rocker moulding clips. The 1969 Sports Special and the 1970 uses the same kit minus two metal end clips, if you have a 69 Sports Special or 1970 model please select that option so as to save $25.00. The 1970 aluminum rocker moulding is held by a Phillips screw on the back thus the need for front clips only. It is rare for us to get a set like...
Availability: Out of Stock
Item #: 19455 -
Ford part number C9WY-6510198-A. This is the metal rocker moulding clip that attaches the front and rear of the mouldings to the car in 1969 (except the Sport Special which only has them on the rear). In 1970 a Phillips screw held the rear end of the rocker moulding to the quarter panel on each side so just the fronts of the mouldings used these clips in 1970. Keep in mind that this same basic clip can be found on 1977-1979 Mercury Cougars and Ford Thunderbirds that were equipped with optional...
Availability: Out of Stock, On Order
Item #: 15440 -
Kit comes with 4 metal clips, Ford part number C9WY-6510198-A and 10 plastic clips, Ford part number C9WY-6510182-A. Pictured is a complete set of 1969 rocker moulding clips. The 1969 Sports Special and the 1970 uses the same kit minus two metal end clips, if you have a 69 Sports Special or 1970 model please select that option so as to save $25.00. The 1970 aluminum rocker moulding is held by a Phillips screw on the back thus the need for front clips only. It is rare for us to get a set like...
Availability: Out of Stock
Item #: 12790 -
Used passenger side (right hand) fender extension moulding / trim for the Mercury Cougar. This unit is sometimes called eyebrow moulding and is a decent part that will look great on a daily driver level car. If you need new attaching clips with nuts, you can get them here. Due to the difficulty in obtaining trim we no longer sell these without first having you send us your cores. Ford Part Number C9WY-16074-A ...
Availability: Out of Stock
Item #: 19456 -
Ford part number C9WY-6510198-A. This is the metal rocker moulding clip that attaches the front and rear of the mouldings to the car in 1969 (except the Sport Special which only has them on the rear). In 1970 a Phillips screw held the rear end of the rocker moulding to the quarter panel on each side so just the fronts of the mouldings used these clips in 1970. Keep in mind that this same basic clip can be found on 1977-1979 Mercury Cougars and Ford Thunderbirds that were equipped with optional...
Availability: Out of Stock
Item #: 20401 -
Excellent condition NOS rocker panel mouldings. These are original Ford parts made on original equipment back in the day. Sold as a pair, no hardware. Items sold will be better than the ones pictured.
The rounded edges on these mouldings go towards the rear, and the flat edge goes towards the front of the car. ...
Availability: Out of Stock
Item #: 25740 -
Correct plastic rocker moulding clips with Ford engineering # C9WB-6510182-A, Ford part #C9WY-6510182-A. There are five of these on each side for a total of ten per car.Fits: 1969 Mercury Cougar1970 Mercury Cougar
Availability: Out of Stock
Item #: 24681 -
Used driver side top moulding for both two tone paint Cougar hardtops and Cougars with a vinyl top. These mouldings will not have any broken studs, cracks, bends or chips. Ford casting # on backside reads C9WB-65423A19-A. *NOTE* Often people think these come off with a pry bar when in fact they are to be removed from the inside of the car. For some reason when people remove them they always start with the drivers side thus the premium price... This icon means that we're looking to buy this...
Availability: Out of Stock
Item #: 15506 -
Good set of four diecast original top mouldings for both two tone paint Cougar hardtops and 1970 Cougars with a factory installed Hounds-Tooth checkered vinyl top. No broken studs, cracks, bends or chips. Originally these came painted on most cars, but in rare cases like the 1970 Hounds-tooth edition or select two tone paint cars, they came chrome plated. These mouldings will need to be re-chromed to look their best.
Availability: Out of Stock
Item #: 15-0135 -
Used vacuum hose for the steering column release valve used in the Mercury Cougar or Ford Mustang equipped with the tilt / tilt away steering column. Regular vacuum hose can be used to replace this hose if you are missing the original. However, it will not be correct. This nice original FoMoCo hose has the correct ribbing, stripes and comes with the firewall grommet. If you are missing this piece and you want your car to be right, this is a must have.
Availability: Out of Stock
Item #: 15504 -
Good set of four die cast original top mouldings for both two tone paint Cougar hardtops and Cougars with a factory installed vinyl top. No broken studs, cracks, bends or chips. Originally these came painted and in rare cases like the 1970 Hounds-tooth edition or select two tone paint cars, those came chrome plated. These trim parts will need to be painted, Includes 15 new or used speed nuts for installation, just in case. This icon means that we're looking to buy this part!WCCC is a buyer of...
Availability: Out of Stock
Item #: 24682 -
Used passenger side rear top moulding for both two tone paint Cougar hardtops and Cougars with a vinyl top. These mouldings will not have any broken studs, cracks, bends or chips. Ford casting # on backside reads C9WB-65424A48.
Availability: Out of Stock
Item #: 24683 -
Used driver side rear top moulding for both two tone paint Cougar hardtops and Cougars with a vinyl top. These mouldings will not have any broken studs, cracks, bends or chips. Ford casting # on backside reads C9WB-65424A49.
Availability: In-Stock Item
Item #: 31323 -
This is for the person who does not want to modify the off-shore Mustang reproduction wheel lip mouldings we sell but do not have good cores for exchange for our premium set of restored wheel lips. Each one of these wheel lips will show some imperfections, mostly found on the inside where the wheel lip fastens to the wheel arch. The blems most commonly found on our less than perfect wheel lip mouldings may include multiple extra little holes drilled for mud flaps, "speckles" in the finish from...
Availability: Out of Stock
Item #: 32335 -
New old stock tilt / tilt away steering column lock relay for the Mercury Cougar or Ford Mustang. Keep in mind we have a reproduction substitution for this part. This unit can be identified with the bend in the bracket compared to the 1967 relay which is straight. Ford part # C8ZA-3E553-A. There is an active thread on the Classic Cougar Community Forum discussing tilt columns and trouble shooting. *NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.co...
Availability: Out of Stock
Item #: 15-0403 -
Used Transition cover for the 68 - 69 Cougar or Mustang tilt steering column. This cover bolts to the outer cover tube.*NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year.
Availability: Out of Stock
Item #: 27130 -
Due to the fact that these convertible mouldings are hard to come by, if your cores are missing clips or have broken studs, your core charge refund will be adjusted accordingly. This original FoMoCo, six piece windshield trim set for the Mercury Cougar convertible has been lovingly restored far beyond the original luster. Stunning brilliance, perfect match for that high end paint job. Because these pieces are restored original pieces, they will have far superior fit and finish when compared to...
Availability: Out of Stock
Item #: 12724 -
This is a core five piece set of front windshield mouldings for a 1969 - 1970 Mercury Cougar. These trim parts need restoration as they are dull, scratched and dinged. They would suffice to make a car complete if you were wanting to drive it but in our opinion they are a step below "good" driver quality. This set will not have any kinks, flattened out areas or holes, we discard trim parts of that description. We do not recommend the reproduction, offshore mouldings that are available as they...
Availability: Out of Stock
Item #: 42346 -
This set of NOS mouldings has been one by one taken out of the wrapper, cleaned and carefully inspected one by one for imperfections or blemishes. Even factory blemishes are not included in this show quality, pristine set. At this price you need to know you are getting the best of the best. We will allow credit for your used or core wheel lip mouldings. You can send your used or core wheel lips in prior or after your purchase and we will call and discuss what amount of credit we will allow on...
Availability: Out of Stock, On Order
Item #: 13629 -
Reproduction Tilt Steering hose for the 69 Cougar or Mustang. Correct in every way, this reproduction is made to be an exact fit for your original hoses.
Availability: Out of Stock
Item #: 15-0064 -
Used emergency flasher knob for the tilt / tilt away steering column equipped Mercury Cougar or Ford Mustang. This unit is a very fragile part which we never find in good used condition. What you will see when it has been broken off is an exposed Phillips screw head. *NOTE* WCCC services all FoMoCo tilt and tilt-tilt away steering columns 1967-1979. Our shop rate for this service is $90 per hour and most columns with serious problems do need complete tear down and build up which usually takes...
Availability: Out of Stock
Item #: 15-0065 -
Emergency flasher bezel for the side of the tilt steering column. Another hard to find, fragile, plastic part. Subject to availability. Paint to match your interior.
Availability: Out of Stock
Item #: 15-0066 -
Steering column to steering box coupler, also known as a 'rag' joint. Used on 1967 1968 1969 1970 Cougar tilt columns, differs greatly from the fixed column version in that is has a "D" shaped fitting on the column side. Good used condition, supplied with one, 12 point attaching bolt. You will need to reuse your existing 12 point bolt for the other end or purchase a second one. *NOTE* WCCC services all FoMoCo tilt and tilt-tilt away steering columns 1967-1979. Our shop rate for this service is...
Availability: Out of Stock
Item #: 15-0067 -
Used wiring cover for the tilt / tilt away steering column found in the Mercury Cougar or Ford Mustang. Unique to the 1968 and 1969 tilt column, fixed column version will not fit on a tilt without modification. Ford part number C8ZZ-13376-A or C8ZZ-13376-B.
Availability: Out of Stock
Item #: 15-0062 -
1967 Cougar Owners: To view our exploded view interactive diagram of the tilt steering column parts, click here. This is the part of the tilt switch that the turn signal wand screws into. This part is always included when you purchase a new turn signal switch. 1967-69 mechanism has two springs on either side, the 1970-73 mechanism uses just one spring. There is an active thread on the Classic Cougar Community Forum discussing tilt columns and trouble shooting. *NOTE* For tilt column service,...
Availability: Out of Stock
Item #: 15-0059 -
Used in the latter part of 1967 and all of 1968 and 1969 to fasten the upper column cover to the column. Early 1967 used a chrome version of this screw.
Availability: Out of Stock
Item #: 22560 -
Mounts horizontally at the base of your quarter window. This used part will show age on the chrome but will not be pitted. If you are wanting to match the patina of a low mileage unrestored car this part will save you money over our repro unit.Ford part number C9WY-6529034-A.
Availability: Out of Stock
Item #: 22561 -
Mounts horizontally at the base of your quarter window. This used part will show age on the chrome but will not be pitted. If you are wanting to match the patina of a low mileage unrestored car this part will save you money over our repro unit.Ford part number C9WY-6529035-A.
Availability: Out of Stock
Item #: 30265 -
This stainless steel passenger side top of the door moulding or upper horizontal door trim was used for 69 - 70 Mercury Cougar XR7 models, including convertible. This NOS or new old stock part, often times it will have minor shelf wear. Included and attached is an NOS belt line weather strip. These stainless steel pieces shine up nicely with 0000 steel wool. No core or core charge required. Ford part number C9WY-6520934-A. *NOTE* The use of this XR7 unique trim requires the use of different...
Availability: Out of Stock
Item #: 30266 -
This stainless steel driver side top of the door moulding or upper horizontal door trim was used for 69 - 70 Mercury Cougar XR7 models, including convertible, but is a nice upgrade for a standard Cougar. This NOS or new old stock part, often times it will have minor shelf wear. Included and attached is an NOS belt line weather strip. These stainless steel pieces shine up nicely with 0000 steel wool. No core or core charge required. Ford part number C9WY-6520935-A. *NOTE* The use of this XR7...
Availability: Out of Stock
Item #: 15-0133 -
1967 Cougar Owners: To view our exploded view interactive diagram of the tilt steering column parts, click here. Used upper knuckle for the tilt / tilt away steering column equipped Mercury Cougar or Ford Mustang. There is an active thread on the Classic Cougar Community Forum discussing tilt columns and trouble shooting. *NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way...
Availability: Out of Stock
Item #: 15-0057 -
Used upper steering column bearing for your 67 - 73 Cougar or Mustang. One required per car. Fixed Columns only use the upper bearing, while the tilt columns used an upper and lower. The used lower bearing can be found here. Outside diameter: 1 3/16 " * - may not fit some 67 Mustang applications with a fixed column as these used Ford part # C4OZ-3517-A, which is the same part used in the Fairlanes/Comets with a fixed column. To our knowledge this bearing is not currently reproduced. *NOTE* For...
Availability: Out of Stock
Item #: 15-0054 -
Rubber isolator used in tilt away steering column near the lower bearing. Two required per car. There is an active thread on the Classic Cougar Community Forum discussing tilt columns and trouble shooting. *NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year. ...
Availability: Out of Stock
Item #: 15-0022 -
Used pivot pin for the Mercury Cougar or Ford Mustang / Thunderbird equipped with a tilt / tilt away column. This is a pressed pin with a flange and five are required per car. This pin is internally threaded with a # 6-32 thread. Ford part # C7SZ-3D739-A. *NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year. ...
Availability: Out of Stock
Item #: 25813 -
Correct for any 1967-73 Ford product with a tilt or fixed column. The repros are fine, but the end knob is distinctly different. Extremely difficult part to find in NOS form and very sought after. Keep in mind we also have excellent used pieces at a fraction of the cost. Ford part # D0AZ-13305-A.*NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is the designer of all of...
Availability: Out of Stock
Item #: 15-0046 -
One required per car, includes Phillips screw.*NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is the designer of all of our solid state sequential systems. There is no question he cannot answer! Here is a link to a great source of information on the subject. ...
Availability: Out of Stock
Item #: 15-0047 -
Used steering wheel tension spring used in the tilt / tilt away steering column found in the Mercury Cougar or Ford Mustang. One required per car. Keeps tension on the steering wheel shaft so as to keep the steering wheel from contacting the upper column cover. There is an active thread on the Classic Cougar Community Forum discussing tilt columns and trouble shooting. *NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC...
Availability: Out of Stock
Item #: 26550 -
Two-piece Stainless Rear Axle Brake Line Set 67, 68 & 69 Mercury Cougar and Ford Mustang with 9"-28 Spline Rear Axle. The Rear Axle Brake Lines are mounted on the axle going to the left and right rear wheels. These will either connect to a caliper hose or thread directly into a wheel cylinder. All lines come Pre-Bent and flared with the correct threaded fittings which reduces your install time tremendously. These stainless-steel lines are T304 but are of a special softer blend to help with any...
Availability: Out of Stock, On Order
Item #: 11441 -
Scott Drake used the original Ford prints to makes these exactly as the originals with heavier gauge steel than the other reproductions we have seen. Unlike the reproductions of the past, these actually fit without the need for modification or the need to jump on the front of the car to install. They are the best braces on the market today by far... Greatly reduces twisting of the chassis. Also strengthens the front end and helps reduce shock tower fatigue and cracking. Also available in Black...
Availability: Out of Stock
Item #: 15-0025 -
This rubber plug is found on the bottom side of 68 and 69 Cougars without tilt column. It covers the access hole for the bolt that removes the column head / collar. We notice that most cars do not have them in place. This could be due to over site at the factory or them being lost over the years as the car has been serviced. We have also noted that Dearborn cars rarely if ever have them present and San Jose built cars often have them in place. If you have a Dearborn built car and have this...
Availability: Out of Stock
Item #: 10671 -
Used wrench or crank, for manually closing the factory installed sunroof installed on any 1967-73 Mercury Cougar. Sunroofs, technically moonroofs, were originally installed by ASC or American Sunroof Corporation. Hertz 1968 XR7-G cars all came with factory sunroofs, as did the Hertz rental 1969-70 Cougar Eliminators. ASC also installed sunroofs in Ford Thunderbird, Lincoln MK III.ASC used Golde mechanical parts from Germany. Golde was a manufacturer of sliding canvas and metal roofs on...
Availability: Out of Stock
Item #: 42027 -
If your are missing your factory Riv-Nuts, or you are installing a passenger side mirror, these are a very easy to use alternative to the metal riv-nuts we offer. Another good application for these is when your existing mirror mounting holes are "hogged out" these slightly over sized inserts are just the ticket. Keep in mind our kit is not only less money than others you may find but the screws are stainless steel. Hole size for these rubber inserts is 3/8". Keep in mind the upper lip stands a...
Availability: Out of Stock
Item #: 33138 -
New Old Stock turn signal flasher for all 1970 Mercury Cougars. For most applications, we highly suggest you upgrade to our solid state version of this unit. Ford part #D0WB-13350-A, D0WY-13350-A. *NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is the designer of all of our solid state sequential systems. There is no question he cannot answer! Here is a...
Availability: Out of Stock
Item #: 19408 -
Good chrome, better fit than the reproductions we sell.
Availability: Out of Stock
Item #: 19416 -
Very nice knob with no missing / lifting chrome. If you don't mind some damage on your knob we have plenty that are less than perfect, mention it and we will give you one for free with your order.
Availability: Out of Stock
Item #: 11-0113 -
Used steel lower dash panel for all 1969 Mercury Cougar and Ford Mustang with factory air conditioning. This is a bolt in dash section, ships bare, no brackets included. The easiest way to identify a 69 lower dash from a 70 is that the square cutout for the steering column measures 6 3/8" wide on the 69 and 7" wide on the 1970. Grade A used no pitting no extra holes. Replaces Ford part number C9ZZ-6504320-D.
Availability: Out of Stock
Item #: 19991 -
This white plastic spacer fits into the back of the right hand inner knob on cars without factory fader or balance. If your inner knob is loose and will not align, you will want to see if this part is in place. The pictures show an example of how it looks once installed. 1968-70 AM-FM radios would not utilize this part because they have a balance feature. Also found on various 1976-70 Ford and Mercury cars such as Galaxie, Fairlane, Torino, Ranchero, Falcon, Montego, and Thunderbird. The knobs...
Availability: Out of Stock
Item #: 21-0131 -
Very nice used Eliminator Only passenger side dash bezel with original 'Cougar' script.NOTE: We can include either the 1969 plastic emblem or the 1970 metal emblem for you when you order this bezel. Mention in the notes which one you prefer. This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of 50% of our web price for parts delivered in hand or by carrier to our...
Availability: Out of Stock
Item #: 25677 -
This adapter is threaded on bottom for PCV valve and 6 degree angled 5/8" nipple on side. Was gold Cadmium plated, not painted. Original Ford part number C7OZ-6A706-A.
Availability: Out of Stock
Item #: 21-0129 -
Very nice used set of 1969 Eliminator Only dash bezels. Set includes: 1969 Only - Driver side instrument cluster bezel, center bezel, and passenger side bezel with original 'Cougar' script. This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of 50% of our web price for parts delivered in hand or by carrier to our Brooks, Oregon location. If you're not interested in store...
Availability: Out of Stock
Item #: 24672 -
Damaged part with one broken tab on the bottom and cracked mounting areas at the top. Guaranteed to look as ugly as the one pictured or your money back. Does not include mounting screws or grommet that inserts in the U shaped cutout for the column.
Availability: Out of Stock
Item #: 10708 -
Plastic filler piece that goes over the steering column and bridges the instrument cluster portion of the dash pad. Ford calls this part a "PANEL" (Instrument Panel Cluster) in the Master Parts Catalog. "A" grade used is one without cracks or chips. Put a desired color in the comments section of the online order. We suggest planning on 'painting to match your interior'. Current color appears to be Aqua Blue. This icon means that we're looking to buy this part!WCCC is a buyer of used and...
Availability: Out of Stock
Item #: 10709 -
Plastic filler piece that goes over the steering column and bridges the instrument cluster portion of the dash pad. Ford calls this part a "PANEL" (Instrument Panel Cluster) in the Master Parts Catalog. "B" grade used is one with a crack and at least one other chip (see picture), you can put a desired color in the comments section of the online order. We suggest planning on 'painting to match your interior'.
Availability: Out of Stock
Item #: 32336 -
Front steel vacuum fitting for 390, 427, 428CJ engines. New Old Stock. Replaces Ford part number C7AZ-9A474-A.
Availability: Out of Stock
Item #: 32337 -
New old stock brass intake manifold fitting that screws into the rear of the 428 CJ intake manifold on all 1969 428 Cobra Jet engines. Similar to the 1967-68 version, but this one has an additional smaller nipple coming out of it. Ford part number C8OZ-9A474-A.
Availability: Out of Stock, On Order
Item #: 26217 -
C7TZ-6A664-A Used after 02-21-1969. Original used hose that connects the original PCV valve to the carburetor spacer plate. All later 1969 S code 390-4V engines. Used hoses will have faded striping (if present), and clamp impressions. Very often the rubber will be hard and showing some degree of stress cracks. *NOTE* These molded and contoured hoses were designed to work with original style PCV valve (modern 90° PCV valves won't work). Additionally anything other than period original intake...
Availability: Out of Stock
Item #: 11320 -
Used threaded PCV valve for use on 390-4V, 428CJ, 427-4V cars from 1967-70. Unknown functioning condition, these have the correct threaded tops and work with either of the 90° elbows available, reproduction or OEM Ford.
Availability: Out of Stock
Item #: 19821 -
Factory cast iron exhaust manifold set, both a correct right C9ZE-9428-A and left C9ZE-9431-A side matching exhaust manifolds. 1969 and 1970 Boss2 Eliminators
Availability: Out of Stock
Item #: 11-0504 -
Used passenger side (right hand) spring from a door latch assembly fits many Ford and Mercury cars. This will fit all years 1967-70.
Availability: Out of Stock
Item #: 11-0505 -
Used driver side (right hand) spring from a door latch assembly fits many Ford and Mercury cars. This will fit all years 1967-70.
Availability: Out of Stock
Item #: 53243 -
Brand new flex plate for all 1967-69 Mercury Cougar and Ford Mustang with any of the 390 engines. Also includes 1968 Cougar GT-E with 427-4V engines. Comes complete with new starter ring gear installed as shown. Neutral balance, meaning this has zero weights attached. *Note - Will not work on 428CJ engines.
Availability: Out of Stock
Item #: 30246 -
This reproduction steering wheel is a replica of the wood rimmed steering wheel originally equipped on 1967 Shelby GT350's and GT500's. It has a beautifully finished real solid wood rim with proper finger indents and a distinctive black band around the back surface just like the originals. The 3 spoke design is brushed stainless steel with 4 chamfered holes per spoke, and unique black rubber finger guards. The main hub is CNC machined aluminum with a satin finish. Each wheel is equipped with...
Spotlight!
Featured!
Availability: Out of Stock
Item #: 32366 -
NOS retainer / friction clips that replace broken injected plastic shaft retainers on fixed or tilt steering collapsible columns on most FoMoCo products starting in 1968 and through the 70's. These installs on the upper piece of what Ford called the Steering Column Shaft Assembly, also known as the inner steering column collapsible shaft. The Steering Column Shaft Assembly is the 2 piece shaft that connects the steering wheel to the rag joint. The upper piece of this shaft...
Availability: Out of Stock
Item #: 15-0169 -
This is a plastic cushion, washer and/or spring between the lower knuckle and inner tube on a 1968 - 1973 tilt-away steering column. These have a larger diameter than the 1967 plastic cushion.*NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year.
Availability: Out of Stock
Item #: 15-0197 -
This clip goes on the upper end of your column and keeps your steering shaft from moving around when you pull up on your steering wheel.See item 31804 for new clip.
Availability: Out of Stock
Item #: 30482 -
This part is located in the left front corner of the panel and has to be rotated inward to remove it from the guide rail so the panel cannot be removed. Imprinted on the plastic portion of the part is a Golde part number 100 414 645. Ford part number C8WY-65502L09-A
Availability: Out of Stock
Item #: 15-0144 -
Cancelling cam for the 67-69 Cougars and Mustangs with fixed columns. This cam is what returns your turn signal switch to the off position. This is not the same cam which comes inside tilt columns.
Availability: Out of Stock
Item #: 33173 -
Basic FMX transmission rebuild kit. Kit includes gaskets, seals, bands, filter, modulator, everything as shown. Fits all Ford FMX transmissions for any 1969-73 Mercury Cougar or Ford Mustang with that X code FMX transmission. Quality kit, same as supplied to professional shops.
Availability: Out of Stock
Item #: 33176 -
O Ring gasket for all automatic transmission dip stick tubes. Replacement gasket for C4, C6, and FMX trans dip stick tubes 1967-73 Mercury Cougar and Ford and Mustang.
Availability: Out of Stock, On Order
Item #: 33160 -
Replacement seal with boot for all 1969-73 FMX and 1967-73 C6 transmissions. Tail shaft and slip yoke seal.
Availability: Out of Stock, On Order
Item #: 16211 -
Brand new flex plate for all 1969 - 73 Mercury Cougar and Ford Mustang with 302 / 351W / 351C engines, and C4, C6, or FMX transmissions. Comes complete with new starter ring gear installed as shown.*Note - Fits common torque converter bolt pattern of 11.40 inches. In 1972 there was a unique C6 torque converter with a 9.50 inch bolt pattern.
Availability: Out of Stock
Item #: 31238 -
Set of 6 new correct bolts for attaching the FMX transmission to 351 engines. Fits all 1967-73 Mercury Cougar and 1967-73 Ford and Mustang with transmission code X, or FMX automatic transmissions. Quality fasteners from AMK.
Availability: Out of Stock, On Order
Item #: 26548 -
Two-piece Stainless Rear Axle Brake Line Set 69 Mercury Cougar and Ford Mustang with 9"-28 Spline Rear Axle. The Rear Axle Brake Lines are mounted on the axle going to the left and right rear wheels. These will either connect to a caliper hose or thread directly into a wheel cylinder. All lines come Pre-Bent and flared with the correct threaded fittings which reduces your install time tremendously. These stainless-steel lines are T304 but are of a special softer blend to help with any possible...