All Products

Used grade "A" driver side (left hand) taillight lens with no heavy scratches, stress cracks or chips. You will want to put a 1969 lens on your 1969 Cougar and a 1970 lens on your 1970 as 69 and 70 have different vertical rib spacing on the chrome bezels which creates different wear patterns.   Ford part # C9WY-13451-A. *NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's...

Grade "B" 1971-72 driver side tail light lens. Grade B lens will have 1 or 2 blemishes which may include a small crack, chip, discoloration, or other defect. Replaces Ford part # D1WY-13450-B. Thinking about adding some LED taillight bulbs to your car? Here is great little video that shows the performance of LEDs and traditional bulbs side by side so that you can make an informed decision. ...

Good used taillight lens with no cracks or heavy scratches. With a little effort you can make a lens like this look new. For the best results use a three step polish like NOVUS. For decent results use a one step polish like Meguires. Sold individually right is the same as left on this application. Ford Part #: C7WY-13450. *NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's...

Used grade "A" passenger side (right hand) taillight lens with no heavy scratches, stress cracks or chips. You will want to put a 1969 lens on your 1969 Cougar and a 1970 lens on your 1970 as 69 and 70 have different vertical rib spacing on the chrome bezels which creates different wear patterns.  Ford part # C9WY-13450-A. *NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the...

Used grade "A" passenger side (right hand) taillight lens with no heavy scratches, stress cracks or chips. You will want to put a 1969 lens on your 1969 Cougar and a 1970 lens on your 1970 as 69 and 70 have different vertical rib spacing on the chrome bezels which creates different wear patterns. Ford part # C9WY-13450-A. This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of 50% of our...

Grade "B" 1971-72 passenger side tail light lens. Grade B lens will have 1 or 2 blemishes which may include a small crack, chip, discoloration, or other defect.  Replaces Ford part number D1WY-13450-A. *NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is the designer of all of our solid state sequential systems. There is no question he cannot answer! Here is a...

NOS passenger side (right hand) taillight lens for any 1969-70 Mercury Cougar. Ford part # C9WY-13450-A. *NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is the designer of all of our solid state sequential systems. There is no question he cannot answer! Here is a link to a great source of information on the subject. Thinking about adding some LED taillight bulbs to your...

Driver side front turn signal and combination side marker lens. Clear color, fits 1971-72 Mercury Cougar all models. Grade A used. These are used and they will have some scratches or scuffs in the plastic.  Using a product like Novus Plastic Polish really improves the appearance and helps make these shine. Replaces Ford part number D1WY-13209-A. This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give...

Driver side front turn signal and combination side marker lens. Clear color, fits 1973 Mercury Cougar all models. These are New Old Stock or NOS, but they will have shelf wear. Meaning light scratches or scuffs in the plastic. Using a product like Novus Plastic Polish really make these shine.Replaces Ford part number D3WY-13209-A. This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of...

Passenger side front turn signal and combination side marker lens. Clear color, fits 1971-72 Mercury Cougar all models. Grade A used. These are used and they will have some scratches or scuffs in the plastic.  Using a product like Novus Plastic Polish really improves the appearance and helps make these shine. Replaces Ford part number D1WY-13208-A. This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we...

Passenger side front turn signal and combination side marker lens. Amber color, fits 1971-72 Mercury Cougar all models. These are New Old Stock or NOS, but they will have shelf wear. Meaning light scratches or scuffs in the plastic. Using a product like Novus Plastic Polish really make these shine.Replaces Ford part number D1WY-13208-A. This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit...

These plates were really clean before they were sent out for restoration, you can get  your Oregon plates restored at http://oregonplates.com/NOTE: The plates and plate numbers pictured are exactly what you'll receive.

Restored rear license lamp assembly for all 1969-70 Mercury Cougars. Plated and restored lamp housing with original glass lens, new gasket, bulb, and wiring pigtail with integral rubber body plug.

This lid is about 17-1/2 inch in diameter. Identified by the wagon wheel like spokes in the stamping. 1967 Mercury Cougar and Ford Mustang with 289 engines. Additionally this lid was used for the Canadian export Cougars and Mustangs in 1968, they continued to use the open emissions system.

Chromed air cleaner lid for all 1973 H code 351-2V engines. About 14.75 inches in diameter. Ford part number for the air cleaner assembly is D3ZZ-9600-A. The air cleaner lid by itself doesn't have a number. This air cleaner lid was never chromed from the factory.

This Ford engine blue painted lid, is about 16-3/4 inch in diameter. Identified by the spokes in the stamping. We get these lids with and without a center ring underneath. The ring can be removed with a bit of effort if you desire. There is a chromed version of this air cleaner lid that was found on 1967 and 1969 Mercury Cougar and Ford Mustang with S code 390-4V engines. Additionally this lid was used on 1969-70 Q code 428CJ or non-ram air Cougars and Mustangs. We believe that this lid was...

This lid was also used on the Hi-Po small block Mustang. The painted version is what you will find for the inner lid on the 68-71 Cougars equipped with Ram Air.

This rechromed lid is found on many years and cars 1968 - 1971. The diameter of the lid is just over 17 3/4", fits on 17.84" air cleaner bases. Application Mercury Cougar Ford Mustang 302 and 351 engines without ram air. Ford / Mercury have had various part numbers listed for this basic lid over the years. The primary difference was the original lids included an engine size sticker. That is why there are so many listings, the basic part number is 9661. This lid was chromed in several...

This was the inner air cleaner lid used on the Mercury Cougars equipped with a 428 Ram Air Cleaner or 429 Cobra Jet Ram Air Cleaner assembly. Although you will often find chrome under the blue engine paint on these lids they are in fact supposed to be painted from the factory. This lid is 14-1/8 inches in diameter. The reason you will often see chrome underneath the paint is that this is the same lid used on the 1967 427 GTE, 289 HiPo equipped early Mustangs and 390 GT / GTA Fairlanes and...

This Grade A quality ashtray lid was located at the rear of the console and was used on all 1967 - 1968 Mercury Cougars except the 1967 standard model and the 1968 XR7G. This ashtray differs from other ashtrays you will see on various Ford products in that it has a brushed finish and a slightly taller lower section. The removable ash receptacle is sold separately.Ford part # C7AZ-6330714-A.

This engine compartment lamp assembly includes lamp socket, bracket, mercury switch, and length of wire. A bit of investigation shows us that an inline fuse was used on the single wire and it has an amp rating of 7.5 amps.Replaces part # C9WY-15702-A

Good used light bar for the convenience control indicator lights on the 1967 Cougar dash face pad. Indicators lights are for belts, door, fuel and park.

Manual control shift linkage assembly for a floor shift C-4 transmission in any 1967-68 Mercury Cougar or Ford Mustang.  Check out our video on rebuilding your shifter below: ...

This is a correct reproduction C6 arm for a 1966 - 1969 FoMoCo pony car and midsize with a floor shift C-6 transmission. This also works on the 1970 as long as the lockout rod is removed. Midsize would be Fairlane Cyclone and the individual models associated with them like Ranchero, etc. Replaces Ford Part #: C6OZ-7A256-B Check out our video on rebuilding your shifter below: ...

Used C6 arm for a 1966 - 1969 FoMoCo pony car and midsize with a floor shift C-6 transmission. This also works on the 1970 as long as the lockout rod is removed. Midsize would be Fairlane Cyclone and the individual models associated with them like Ranchero, etc. Replaces Ford Part #: C6OZ-7A256-B Check out our video on rebuilding your shifter below: ...

Manual control shift linkage assembly for a floor shift FMX transmission in any 1969 Mercury Cougar or Ford Mustang. Comes as shown.  1969 linkage is different than 1970, 1970 included a provision for the steering column lock out rod. Check out our video on rebuilding your shifter below: ...

Manual control shift linkage assembly for a floor shift FMX transmission in any 1971-73 Mercury Cougar or Ford Mustang. Comes as shown. *Note - this will not work with a C6 transmission.

A perfectly working, matched set of trunk and glove box locks with key is getting rather hard to come by these days. These two matching locks are guaranteed to work perfectly. Includes 1967 style glove box lock, 1967-68 Cougar trunk lock cylinder with one "Ford" cut key to the coded to the number imprinted on the glove box lock. This is a matching set with new key. 1967 glove box locks has square edges on the front of the lock. Starting in 1968 the lock had a rounded edge on the front. We also...

This deck lock housing has been carefully stripped, polished and triple plated. You can send yours in in advance as an exchange or pay the core charge and return your old one later. Do know once a multi-faceted part like this has been stripped, polished and replated, some of the crisp, sharp detail will be muted and it will never again look just like factory. If you have extra cores we are buyers, especially if your lock assembly is complete. Be sure and watch our video below to see how to...

Used locking pawl for the 1970 - 1979 Mercury Cougar or Ford Mustang that is equipped with a factory tilt steering column. This unit works in conjunction with a pin and is responsible for locking the tilt column in place. In many cases, the pin tends to move out of place and break or chip the teeth of the locking pawl. We have found that 3 of 4 tilt columns that we have disassembled have locking pawls with broken or chipped teeth. These units will be mint with no broken or chipped teeth....

This is a rebuild service in which we will replace the locking pawl and cable. We provide this service for Cougars, Mustangs and T Birds.Ford part number C9ZZ-3E520-A THIS SERVICE REQUIRES THAT YOU SEND IN YOUR CABLE IN ADVANCE.

Locking pawl cable assembly for 67 - 69 TILT column T-Birds.

Rod used for locking the C-6 transmission in "Park". Connects to the lower tab of the steering column and the C-6 transmission shift arm. Prevents the transmission from shifting out of park when the ignition key is removed. Rod is about 13 inches long and was originally marked with a red paint mark or daub. Casting number stamped on the rod - D1ZA-7E330-BA. The C-6, automatic transmission, could be ordered with any engine from 1971 - 1973. Transmission code "U" on your door data tag.

Finally a quality reproduction lower control arm for the one year only 1967 lower control arm! Deigned to work with your existing articulated strut rod arms found only on the 1967 Mercury Cougar. *NOTE – Can only be used with 1967 Cougar lower control arms C7WY-3468-C (ITEM # 15393). Replaces Ford Part # C7WY-3078-A Having issues with wobbly or loose steering? Check out our video on sloppy steering below. ...

Used chrome moulding that attaches horizontally to the bottom of the headlight bucket. Driver side for any 1971-73 Mercury Cougar. 1973 used a different casting number but the parts are exactly the same. A grade will have nice chrome, and maybe one minor blemish. We consider these 'show quality' rather than 'driver quality'. We do offer a B Grade version of this part, and always have them in stock.Replaces Ford part number D1WB-13B167-AB and D3WB-13B167-AA.

Restored driver (left hand) side lower headlight housing moulding for any 1971-1973 Mercury Cougar. We also have grade A and B used mouldings. Refundable core charge additional.Mercury casting # D1WB-13B167-AB or D3WB-13B167-AA.

Used chrome moulding that attaches horizontally to the bottom of the headlight bucket. Passenger side for any 1971-73 Mercury Cougar. 1973 used a different casting number but the parts are exactly the same. A grade will have nice chrome, and maybe one minor blemish. We consider these 'show quality' rather than 'driver quality'. We do offer a B Grade version of this part, and always have them in stock.Replaces Ford part number D1WB-13B166-AB and D3WB-13B166-AA.

Restored passenger (right hand) side lower headlight housing moulding for any 1971-1973 Mercury Cougar. We also have grade A and B used mouldings. Refundable core charge additional.Mercury casting # D1WB-13B166-AB or D3WB-13B166-AA.

Used grade A lower center console pad for the 1967 Standard Automatic Transmission. We rarely have these in stock so the chances of getting the color you desire is slim. We have several Grade B's with cigarette burns, cracks and the like for substantially less money.

Used grade B lower center console pad for the 1967 Standard Automatic Transmission. We rarely have these in stock so the chances of getting the color you desire is slim. 

Used only in 1968 on non xr7 models and Mustang. Very hard to come by with no splits, burns or cracks. We often can supply the color you desire, please let us know your desired color and we will try. Grade B will need to be repainted and will not be as soft and straight as grade A. The simulated stitching embossed in the vinyl may show areas of slight separation.

This pad is in poor condition. You can actually modify a automatic pad to work with your manual transmission chrome bezel. *NOTE* If you have a clean example of this pad for sale we would like to hear from you!

Good lower pad with no cracks or burns. We have several of these in stock but cannot guarantee we can give you the color you select. Mention in the notes of your order what color you would like and plan on repainting this item even if we can provide your color as there is always some discoloration from age and use.

Good lower Grade B pad with no cracks or burns. We have several of these in stock but cannot guarantee we can give you the color you select. Plan on repainting this item even if we can provide your color as there is always some discoloration from age and use. Grade B will be pulling away from the base and will need glued.

Reproduction CHARCOAL lug nut cover deigned to fit the Cobra / Eleanor style Legendary LW90 wheel.  Sold as a set of 4 and includes 20 Legendary low profile lug nuts.

Reproduction GOLD HAZE lug nut cover deigned to fit the Cobra / Eleanor style Legendary LW90 wheel.  Sold as a set of 4 and includes 20 Legendary low profile lug nuts.

This version with a cast head was only found in the earliest 1967 Mercury Cougars. 13/16 inch socket. Much better quality than the later stamped steel version.

Nice reproduction of the original Rotunda, over the counter dealer accessory. Stainless steel construction, weighs just under 8 pounds. The supplier unfortunately does not include the hardware and we have yet to source any. Actual dimensions are 20 1/2 inches wide, 48 1/2 inches long, and the back lip is 3 inches tall. Installation hole spacing is as follows. Rear spacing 47-11/16" on center, front spacing (nearest the rear window) is 47-9/16". The spacing on short sides are 18-3/4" on...