All Products

Application - 1967 Mercury Cougar and Ford Mustang with 390 engines.  Might be two versions, this one would be the mid or late version. There are references that this bracket was also used on 289 engines with air conditioning, but that may not be consistent through out the year, if it all. Maybe early 1967 cars with A/C. Ford part number stamped C7AE-9B453-A.

Used battery clamp to inner fender apron "L" bracket for 69 - 70 Cougars and Mustangs.This bracket secures the battery clamp to the inner fender apron. Ford Part # C9ZZ-10A705-A

Driver side convertible frame assembly mounting and pivot bracket for all 1971-73 Mercury Cougar and Ford Mustang. Does not include the hydraulic cylinder bracket, cylinder mounting bracket sold separately. Bushings, bolts, and specialty fasteners not included. Mounts behind the quarter interior panel.  Ford part number D1ZZ-7653119-A.

Passenger side convertible frame assembly mounting and pivot bracket for all 1971-73 Mercury Cougar and Ford Mustang. Does not include the hydraulic cylinder bracket, cylinder mounting bracket sold separately. Bushings, bolts, and specialty fasteners not included. Mounts behind the quarter interior panel.  Ford part number D1ZZ-7653118-A.

Detachable mounting plate for installing the passenger side convertible ram cylinder, to the convertible top frame assembly behind the quarter interior panel. Right and left are the different, fits all 1969-70 Mercury Cougar and 1965-70 Ford Mustang convertibles. Ford part number C5ZZ-76531A18-A.

Detachable mounting plate for installing the convertible ram cylinder to the convertible top frame assembly behind the quarter interior panel. Right and left are the same, fits all 1971-73 Mercury Cougar and Ford Mustang convertibles. Ford part number D1ZZ-76531A19-A.

Used front license plate bracket in Grade A condition. Grade A will, not have creases, cracks, or damage of any kind. The 1969 reproduction bracket, which mounts directly to the front valance, is what we recommend for a reasonable priced substitute. We also sell a B grade of this 1970 front license plate bracket.Replaces Ford part number D0WY-17A385-A.

These are our best used front license plate mounting bracket that attaches to the passenger side of the bumper of all 1971-72 Mercury Cougars. It may or may not have the rubber anti rattle bumpers present, but will have either original or reproduction plastic inserts for screwing on the license plate.Replaces Ford part number D1WY-17A385-A. This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store...

For restoration purposes, this bracket was factory painted satin black. May or may not have a stamped number of D1OA-3C511-AA. *This bracket can only be used in conjunction with an all steel pump mounting bracket. 71 72 73

Take a look at the smaller image to see the repro and used side by side. The repro is slightly taller and has extra holes in it so it fits other applications. Why deviate from 100% correct if you don't need to. Ford Part # C9ZZ-18842-A.

Used in conjunction with the front bracket, bolts onto stud protruding from the rear of your radio, rather hard to find once the original radio has been removed. One exception; 1972-73 Mercury Cougar and Ford Mustang AM/FM radios used a different bracket marked D2ZA-18888-AB. *Customer Feedback*"These guys have got to be the most professional I've dealt with in the 4 years I've been restoring my Mustang and Cougar. I have had nothing but pleasant conversations even though I tend to be long...

Used Bracket for mounting the Servo on any 1967-68 Mercury Cougar or Ford Mustang with speed control. The Servo is the rubber bellows. Ford part number C7ZZ-9C736-A.

Used Bracket for mounting the Servo and accelerator Shaft on any 1969 Mercury Cougar or Ford Mustang with speed control. The whole assembly mounts to the firewall inside the passenger cabin. The Servo is the rubber bellows. We think the the Ford part number was C9ZZ-9C787-A. Ford part number 9C787.

Weld in bracket for attaching the trunk lock striker on any 1971-73 Mercury Cougar, coupe or convertible. Majority of these have rust forming at the base where it meets the trunk floor. Removed from a rust free western Cougar. Ford part number D1WY-6543235-A.

The originals hang at a slightly different angle than the reproductions. Comes as shown with original rubber insulator. New rubber available upon request. Seldom in stock, we suggest the 1969 small block version. It is very close to this one. Please see related item. This is the bracket needed if you are routing the PS lines under the lower control arm instead of over as found on the 67 - 68 small block. Replaces Ford part # C7ZZ-3C510-A, and C7ZZ-3C510-C.

Reproduction power steering hose retaining bracket and retainer. This is the bracket needed if you are routing the PS lines under the lower control arm instead of over as found on the 67 - 68 small block. Bracket and retainer will work on 1967-70 Mercury Cougar and Ford Mustang with small block V8 cars with the correct  power steering hoses. Replaces Ford part # C7ZZ-3C510-A, and C7ZZ-3C510-C.

The originals hang at a slightly different angle than the reproductions. Comes as shown with original rubber insulator. New rubber available upon request. Replaces Ford part # C7ZZ-3C510-A, and C7ZZ-3C510-C.

This flexible vinyl cover attaches to the upright brackets that mount your center fold down arm rest. The number stamped on the back for the cover closest to the driver is C5ZB-6561693-BW. If yours is other than black in color the BW will be something else. Very rare part that is difficult to obtain.

This flexible vinyl cover attaches to the upright brackets that mount your center fold down arm rest. The number stamped on the back for the cover closest to the driver is C5ZB-6561692-BW. If yours is other than black in color the BW will be something else. Very rare part that is difficult to obtain.

Reproduction passenger side (right hand) front wheel cylinder for 10 inch x 2-1/2 inch drum brakes. This unit fits in a 1-3/32 inch hole on the brake backing plate. Replaces Ford Part # C6OZ-2061-B or C9TZ-2061-B.

C9OZ-2212-C Left hand rear brake backing plate for use with 1-3/4 inch wide brake shoes. Clean Western part with no heavy corrosion like you see on Eastern cars. Inspected for excessive wear. Also used on 6 cyl and 302 Mustangs in 69-71. Used on cars with 10" drums.Originally manufactured by Kelsey-Hayes, KH part number 70867. Originally manufactured by Bendix part number 319480.

C9OZ-2211-C Right hand rear brake backing plate for use with 1-3/4 inch wide brake shoes. Clean Western part with no heavy corrosion like you see on Eastern cars. Inspected for excessive wear. Also used on 6 cyl and 302 Mustangs in 69-71. Used on cars with 10" drums.Originally manufactured by Kelsey-Hayes, KH part number 70866. Originally manufactured by Bendix part number 319481.

C3OZ-1126-B Used brake drum with the vintage casting look. Guaranteed to successfully be turned and not exceed the manufacturers inside maximum of 10.060". When we say the "vintage casting look", we mean with the proper groove and contours. Reproductions are fine, but do not retain the casting design of the original casting company. When looking for used brake drums, the rule of thumb is to find ones with a brake surface area of 1/4 inch more than the brake shoe width.

Stainless steel version features extra corrosion protection with correct zinc chromate plated fittings and are exact copies of the originals with color coded fittings.

Steel tubing features tin/lead coating and plated zinc chromate fitting and are exact copies of the originals with color coded fittings. New copy of the 1968-69 Mercury Cougar and Ford Mustang manual drum brake master cylinder lines. 

Two piece pre-bent OE steel brake line kit that runs down the rear axle on the 8 inch rear end of a 1967, 1968 or 1969 Mercury Cougar or Ford Mustang.The Rear Axle Brake Lines are mounted on the axle going to the left and right rear wheels. These will either connect to a caliper hose or thread directly into a wheel cylinder. All lines come Pre-Bent and flared with the correct threaded fittings which reduces your install time tremendously. These mild steel lines are Galphan coated for...

Used brake pedal for the Mercury Cougar or Ford Mustang equipped with an automatic transmission and drum brakes. This is a short style pedal is for cars with four wheel manual drum brakes and is shipped bare.Ford part # D1ZZ-2455-C.

Used brake pedal for the Mercury Cougar or Ford Mustang equipped with a manual transmission and drum brakes. This unique pedal that works with the wider collapsible 1968 steering column and with a clutch pedal. Shorter arm than power brake pedals. The picture may show hardware and pedal pad with trim, but the pedal is shipped bare.Ford part # C8ZZ-2455-E.

Used brake pedal for the Mercury Cougar or Ford Mustang equipped with a manual transmission and drum brakes. This unit is for use with a clutch pedal and has a shorter arm than power brake pedals. The brake pedal is shipped bare. Fits any 1969-70 Mercury Cougar or Ford Mustang.Ford part # C9ZZ-2455-B.

Grade A used driver side bucket seat textured plastic trim panel. Available in black, blue, red, ginger, avocado, green, and white. Please specify in the notes your desired color, ginger seems to be the most prolific color, the others may or may not be available. Grade A will not be chalky or have major scuffs or scratches. Various Ford part numbers associated with this panel, here are a few: D12B-6260763, D3ZB-6561633, D1FZ-6260763, D2ZZ-6260763, and D3ZZ-6560763. We also have B...

Grade A used passenger side bucket seat textured plastic trim panel. Available in black, blue, red, ginger, avocado, green, and white. Please specify in the notes your desired color, ginger seems to be the most prolific color, the others may or may not be available. Grade A will not be chalky or have major scuffs or scratches. Various Ford part numbers associated with this panel, here are a few: D12B-6260762, D3ZB-6561632, D1FZ-6260762, D2ZZ-6260762, and D3ZZ-6560762. We also...

Female buckle end seat belt for the 73 Cougar or Mustang. The face plate and spring assembly have been replaced on this belt, and has an aftermarket starburst button decal. The originals had the olive branch decal.  This is the actual belt you will receive. Measures 11-1/2" This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of 50% of our web price for parts delivered in hand or by...

This is a complete kit for front and rear. If you own a 71 - 73 and then you will need two more bolts. mercurycougar.net: I was in Salem on business Monday when I decided to give West Coast Classic Cougar a call. Don was gone but Lin was there, talk about a nice guy I looked around the shop and Lin got me the parts I needed for my 68 Coupe. I am sure Lin was busy but he took the time to answer any questions I had, swapped a few stories and gave me a real good deal. I recommend anyone needing...

C9WY-17755-A Front bumper mounting bracket, 1969-70 Mercury Cougar driver side.

Rear bumper filler for any 1971-72 Mercury Cougar. No chips or cracks. Does not come with fasteners or clips. See related items for new aftermarket style clips for attaching, 8 total are needed. Replaces Ford part number D1WY-17808-A . * Note - Will not fit 1973 Mercury Cougar.

Rear bumper filler for any 1973 Mercury Cougar.No chips or cracks. Does not come with fasteners or clips.See related items for new aftermarket style clips for attaching, 8 total are needed.Replaces Ford part number D3WY-17808-A .* Note - Will not fit 1971-72 Mercury Cougar.

Used driver side (left hand) bumper guard for the Mercury Cougar. The chrome plating was pretty low quality back in the day and this unit will show some scratches and pitting as it is an almost 50 year old original part.Ford part # C7WY-17997-A for the driver side.

Used passenger side (right hand) bumper guard for the Mercury Cougar. The chrome plating was pretty low quality back in the day and this unit will show some scratches and pitting in the chrome as this is an almost 50 year old original part.Ford part # C7WY-17996-A for the passenger side. ...

Rare find, NOS rubber rub strip for the front bumper guard on 1971-72 Mercury Cougar. These hard rubber bump strips attach to the front bumper guards with 2 studs from the back side. Sold individually, right is the same as left, Ford Casting number as found on the back is D1WB-17A812-AB

D3AZ-17A812-A Front bumper guard rubber pad used prior to September 5, 1972, on a 1973 Mercury Cougar. The early front bumper guards had a narrow rubber pad early on. The rear flat surface measures 3/4 inches wide. Same rubber strip either right or left side. Hard to find without some scaring on the rubber. This pad is not nearly as common as the wider one which measures about 1-1/8 inches wide.Replaces Ford part number D3AB-17A812-A.

D3AZ-17A812-B Front bumper guard rubber pad used after September 5, 1972, on a 1973 Mercury Cougar. These later front bumper guards have a rubber pad that measures 1-1/8 inches wide on the flat rear surface. Same rubber strip either right or left side. Hard to find without some scaring on the rubber. This pad is more common than the thinner 3/4 inches wide pad.Replaces Ford part number D3AB-17A812-B.

New old stock rubber fender to hood bumpers. Set of 4 NOS Ford. Replaces Ford part #: C6OZ-16758-A.

New Old Stock lower distributor bushing for most V-8 engines 1965 through 1968-69. Ford deemed this bushing as not needed during 1968. That is why all 351W distributors do not have one installed. All 289 distributors 1965-67 should have one installed, starting in 1968 some did, some did not. Many 1968-69 302-2V's and all Boss 302 distributors had them installed. Same with FE distributors all had them starting in 1965, by 1968-69, they were disappearing. Limited to stock on hand. If Ford deemed...

Used plastic bushing for the lock pawl rod guide for the tilt / tilt away steering column in the Mercury Cougar or Ford Mustang. These delicate little bushings are needed to keep the lock pawl rod in alignment with the vacuum motor shaft. *NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year. ...

Although this premium reproduction strut rod bushing kit appears very similar to the economy kit, they are in fact superior. The main difference being that the bushings are made from a higher quality rubber compound.Replaces Ford Part #: C6OZ-3A187-AR.

Reproduction ram cylinder bracket bushings for the 68 - 70 Cougar or Mustang. If you're having trouble with the bushings on your car ripping or tearing through the hole in your power steering ram cylinder bracket (more so with our reproduction drop down bracket), you can purchase this pair of polyurethane bushings to replace your existing ones. The boot kit we sell also comes with similar bushings, but are a lower quality item, so this set should solve your problem. Sold as a pair. ...

C60Z-6222454-B door handle hardware kit for 69-70 Cougar as well as select Torino / Fairlane / Cobra / Falcon

C9ZZ-2853-A Front emergency brake cable for all 1969-70 Mercury Cougar and Ford Mustang. Front cable attaches to the emergency foot brake. New Old Stock, measures 43-5/8 inches long.