All Products

This reproduction rear emergency / parking brake cable kit fits from equalizer to rear brakes. 2 required per vehicle. Equal length emergency brake cables for 1967 on both the Mercury Cougar and Ford Mustangs. Upgrading to the 1968 unequal length cables can easily be done. Equal length cables is correct for 1967 Mercury Cougar and Ford Mustangs. Fits L.H. or R.H., the Cougar uses a longer keeper than the Mustang to compensate for the added wheel base length. Replaces Ford part # C7ZZ-2A635-A,...

This is our heater cable for use with Mercury Cougars and Ford Mustangs with factory equipped A/C. The best part, its NOS, so you know it will fit right the first time! Ford part # C9ZZ-19988-A.

New Old Stock cable for any 1971-73 Mercury Cougar. Cable only, handle needs to be replaced from your unit. Drift pin hold it onto the cable. Reuse your bezel too. Ford Part Number: D1WY-2760-A or D1WY-2A760-A This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of 50% of our web price for parts delivered in hand or by carrier to our Brooks, Oregon location. If you're not...

NOS heater cable for 1969 - 1973 Cougars or Mustangs that are not equipped with factory air conditioning.Ford Part #: D1ZZ-18518-A

This used emergency / parking brake cable connector is for the Mercury Cougar only. That is because it is longer than the Mustang version due to the Cougar's longer wheelbase. This connector connects the two ball ends of the long and short emergency brake cables. Ford part # C7WY-2A790-A.

Used passenger side (right hand) disc brake caliper mounting bracket that is a unique and one year only bracket for mounting the Kelsey Hayes twin piston caliper to the 1967 Cougar brake spindle. Tough parts to find in rebuildable condition. We won't always have them in inventory as singles unless we have multiples of these extra brackets for one side or the other. Ford part # C7OZ-2B134-A.Check out our restoration tips video: ...

1967 289-2V autolite 2100 carburetor, automatic C4 transmission - 49 states. C7DF-F stamped on the carburetor base, 1.02" venturi size and 240 cfm. Core carburetor with proper numbers, we don't always have the factory Ford Autolite tag that was affixed to the top. PCV spacer plates also available and required for stock air cleaner clearance on top of engine. C code 289-2V engines and automatic transmissions. *Note - Not for DSO 52 and DSO 53 California destined cars. ...

1967 289-2V Autolite 2100 carburetor, automatic C4 transmission - California DSO 52 and 53. C7DF-H stamped on the carburetor base, 1.02" venturi size 240 cfm. Core, rebuildable carburetor with proper numbers. We don't always have the factory Ford Autolite tag that was affixed to the top. PCV spacer plates also available and required for stock air cleaner clearance on top of engine. C code 289-2V engines and automatic transmissions. *Note-for use with California Thermactor smog equipped...

1967 289-2V Autolite 2100 carburetor, automatic C4 transmission - California DSO 52 and 53. C7DF-N stamped on the carburetor base, 1.02" venturi size 240 cfm. Core, rebuildable carburetor with proper numbers. We don't always have the factory Ford Autolite tag that was affixed to the top. PCV spacer plates also available and required for stock air cleaner clearance on top of engine. C code 289-2V engines and automatic transmissions. *Note-for use with California Thermactor smog equipped...

1967 289-2V carburetor, automatic C4 transmission - 49 states. C7DF-F stamped on the carburetor base 1.14" venturi size 300 cfm. Core carburetor with proper numbers, we don't always have the factory Ford Autolite tag that was affixed to the top. PCV spacer plates also available and required for stock air cleaner clearance on top of engine. C code 289-2V engines and automatic transmissions. *Note not for DSO 52 and DSO 53 California destined cars. *NOTE - Take a kid for a ride in a classic...

1967 289-2V Autolite 2100 carburetor, manual transmission - 49 states. C7DF-S stamped on the carburetor base, 1.02" venturi size 240 cfm. Application for 3 and 4 speed manual transmissions. Rebuildable core carburetor with proper numbers, we don't always have the factory Ford Autolite tag that was affixed to the top. PCV spacer plates also available and required for stock air cleaner clearance on top of engine. *Note - Not for DSO 52 or DSO 53 cars destined for California. *NOTE* Take a...

1967 289-2V Autolite 2100 carburetor, automatic C4 transmission - California DSO 52 and 53. C7DF-V stamped on the carburetor base, 1.14" venturi size 300 cfm. Core, rebuildable carburetor with proper numbers. We don't always have the factory Ford Autolite tag that was affixed to the top. PCV spacer plates also available and required for stock air cleaner clearance on top of engine. C code 289-2V engines and automatic transmissions. *Note-for use with California Thermactor smog equipped...

Basic kit for rebuilding your Ford Autolite or Motorcraft spread bore 4300D or 4 barrel carburetor with large secondary venturis. Covers all factory 4 barrel carburetors for all 1972-73 Mercury Cougar and Ford Mustang with Autolite or Motorcraft 4300 carburetors. Excludes earlier square bore 4300 carburetors.

CARBURETOR SPACER PLATE, 0.28" thick, has correct tab marked "FRONT". Replaces Ford Part Number C8AZ-9A589-G

Factory two barrel carburetor spacer plate. Positions carburetor above intake manifold for proper linkage operation. With PCV fitting at rear. Unique to the X code 390-2V premium fuel engines.

Grade B used A/C center vent for any 1967-68 Ford Mustang. Grade B will have a defect or two in the chrome plating.Replaces Ford number C7ZA-19623.

New Old Stock center cap emblem for the Mercury Cougar with XR7 hubcaps / wheel covers. On the XR7 package, this concave aluminum applique was applied to the center of the hubcap / wheel cover. Called an applique. Used only in 1968 on the one style XR7 hubcap. Not sure why it has a 1969 part number, error? Ford part number C9WY-1137-A.

Used chrome / black center cap for the 67 - 68 Mercury Cougar equipped with the wire spoke hubcaps / wheel covers.Fits:1967 Mercury Cougar1968 Mercury Cougar

Reproduction chrome center cap with a black background and chrome Mercury Man logo for the Mercury equipped with the Magnum 500 wheel. The screw on mounting system on this reproduction cap is far superior to the original clip-on center caps. There are other reproduction center caps out there, but they are not nearly as nice. When using center caps on Legendary wheels, you will need these adapter plates. *NOTE* *NOTE* When installing these die cast center caps, keep in mind over tightening...

Chrome center cap with Red background and chrome Walking Cat logo for the Mercury Cougar. These are held on by a sturdy plate and two screws from the backside which is much better than the original clip-on type. There are other reproductions out there, but none are of this quality. When using center caps on Legendary wheels, you will need these adapter plates. *NOTE* When installing these die cast center caps, keep in mind over tightening will separate the backing from the chrome outer...

Reproduction chrome spinner cap for the Mercury or Ford that is equipped with Magnum 500 wheels. This cap will also work with any Ford, GM or Mopar Magnum 500 wheel. With a mounting system that is far superior to the original, this unit will definitely give your ride a more aggressive look. *NOTE* When installing these die cast center caps, keep in mind over tightening will separate the backing from the chrome outer portion. Instead of over torquing, we recommend a good threadlocker which...

Used chrome / red center cap for the 1967 and 1968 Mercury Cougar and Ford Mustang Equipped with the Wire Spoke Hubcaps / Wheel Covers. Fits:1967 Mercury Cougar1968 Mercury Cougar

The only reason you would buy an original used unit is that you would want to match your existing original caps. The reproductions we carry are actually much better quality than the originals, as they will never fall off. Chrome center cap with black background and chrome Mercury man logo. Came from the factory on 1967 and 1968 Mercury Cougars with Styled Steel Wheels, but will work on any 67-70 with Styled Steel Wheels. Fits the following models with style steel wheels: 1967 Mercury...

These original clip on center caps are an inferior design compared to our reproductions that screw on from the back. The originals had varying shades of blue, whereas the repro has a solid blue. The only reason you would purchase this fragile expensive used cap is to match what you currently have on a very original car. When using center caps on Legendary wheels, you will need these adapter plates. Ford part # C9WY-1130-BCheck out our center cap installation tips video below: ...

This XR7-G center cap adapter cone was used in conjunction with the RADER wheel and is needed to mount the center cap to the aluminum centered wheel. This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of 50% of our web price for parts delivered in hand or by carrier to our Brooks, Oregon location. If you're not interested in store credit, just shoot us an email and we will let you know...

1970 Mustang with deluxe woodgrain console insert. Fits all 1969-70 consoles, but the 1969 console insert had the seat belt storage cups. NOTE: These inserts came with enough studs to fit multiple cars. When installing this insert, simply clip off the extra studs you don't need.

New old stock check valve for Bendix brake boosters. This is a white plastic check valve. Ford part number D0AZ-2365-A.Check the related items, for a reproduction rubber grommet.

Screws onto the cylinder head smog tubes. Sold individually, two needed per application. Ford part number C8AZ-9A487-A.

This is the 100% correct Ford original battery hold down clamp. Stamped with D0OB10755A. Ford Part #: D0OZ-10718-B. Note: The battery hold down clamp offered by many Mustang / Cougar vendors as "Concours Correct" is actually for the 1974 - 1978 Cougar /  Mustang.

Yoke style factory exhaust pipe clamp. For 2 inch outside diameter exhaust pipes. Two piece clamp see picture Ford part number D1AZ-5A231-C.

Band or ring style factory exhaust pipe clamp. For 2-1/4 inch outside diameter exhaust pipes. Comes with a course sheet metal type hex head bolt. Ford part number C6AA-5A272-A. *Not all 1969 & 1970 Cougars had 2-1/4 inch tailpipes from the factory. Check the outside diameter of your current tailpipe for fitment. Part number C5DA-5A272-B is the factory style 2" tailpipe clamp.

Yoke style factory exhaust pipe clamp. For 2-1/4 inch outside diameter exhaust pipes. Two piece clamp see picture Ford part number D1AZ-5A231-A.

NOS rocker moulding end clip. Fits all 1968 Mercury Cougars. This clip is plastic and metal, it has a stud which goes through the body of the car. Sold individually, 4 total needed per car. Our all metal version of this clip is reproduced and is a better value. Find it here.Ford part number C7OZ-6221094-A.

Used grade A rocker panel clip for the 71 - 73 Mercury Cougar 

Ford part number C9WY-6510198-A. This is the metal rocker moulding clip that attaches the front and rear of the mouldings to the car in 1969 (except the Sport Special which only has them on the rear). In 1970 a Phillips screw held the rear end of the rocker moulding to the quarter panel on each side so just the fronts of the mouldings used these clips in 1970. Keep in mind that this same basic clip can be found on 1977-1979 Mercury Cougars and Ford Thunderbirds that were equipped with optional...

C7WY-15000-A 1967 - 1968 Standard Cougar body code 65A or 65C, found optionally in the small center pod of the instrument cluster. Used clocks generally do not work after 40 years. These are considered cores. We also offer clocks with modern quartz movements or NOS movements in restored clocks. Check out the videos below on our new gauge tester and the "Cougar Dash Surgery Clock and Speaker Install by Andrew Chenovick: ...

Reproduction premium adjusting rod which includes: 2 Lock Nuts 1 Spacer 1 Retaining Clip Fits the 1968, 1969, and 1970 Mercury Cougar with the 390GT, 428CJ or the 428SCJ. Replaces Ford Part #: C8ZZ-7521-BR. Can be used on 1967 3 or 4 speed cars with 390 engine, but must use the 1968 clutch fork, see item 13882.

New Old Stock set of brushes only fits the Eaton brand of air compressor clutch. Pitts compressor clutch is the most common one starting in 1969. These are exact reproductions made from the original tooling.Ford part #: C8SZ-2979-A

C9ZZ-7528-A Equalizer bar or "Z" bar for 351 cubic inch Windsor engines and Boss 302 Eliminators with manual transmissions. Both 3 and 4 speed manual transmissions. This is a used part and it will most likely show some wear form previous use.

Used clutch spring bracket that attaches to the brake / clutch hanging bracket. All 1967-68 Mercury Cougar and Ford Mustang with manual transmissions. Replaces Ford Part #: C7ZZ-7535-B.

Made of heavy gauge steel with a satin black painted finish. Replaces Ford Part #: C9ZZ-7535-A.

Powerful oil filled coil that generates 40,000 volts, designed to work with the either of our Pertronix Ignitors. Sold in black or chrome. *Note - This coil is not necessarily needed with the Pertronix Ignitors, the stock Ford coil works fine for most applications.

Tall version 1" thick and can be used with performance springs to bring the car to a stock ride height. Sold as a Pair. Replaces Ford Part #: C4DZ-5415-A.

Used steering column shroud or collar for any 1970 Mercury Cougar or Ford Mustang. These come in various colors, and have a rough texture. These will have some scratches in the surface, specify your desired color in the notes or comments section, but do know that black is in short supply. Ginger anyone?*Note does not include the retainer or clip, we cannot keep them in stock.Replaces Ford part numbers D0ZZ-3530-A.

Developed on a 3D printer, good fit but notice the texture is not the same. Four speed and Automatic transmission use the same bezel.

Used grade B condition mini console assembly, comes with ash tray receptacle. Good for automatic or manual transmissions. We will select and ship what is available, these are easy to detail with the various vinyl paints available. These are used, and often the ashtrays will need bead blasting. Grade B does not come with wiring harness for the light. They will have minor damage, examples include cigarette burns or small holes or other imperfections.  These came color...

Reproduction transmission cooling lines made of OE steel for the Mercury Cougar or Ford Mustang equipped with the FMX automatic transmission and 351C engine. These lines are sold in pairs.

These were never offered originally but are a popular accessory and more cost efficient than buying a replacement for that unsightly old wheel and tire you took from a Granada in the bone yard!