Body

Rust free with no prior damage. Cut with a plasma cutter well above the style line from a solid Western fender. Generally we cut these about 14" up but you can have it cut anywhere you wish and the price remains the same, only the shipping increases.

Rust free with no prior damage. Cut with a plasma cutter well above the style line from a solid Western fender. Generally we cut these about 14" up but you can have it cut anywhere you wish and the price remains the same, only the shipping increases.

Rust free with no prior damage. Cut with a plasma cutter well above the style line from a solid Western fender. Generally we cut these about 14" up but you can have it cut anywhere you wish and the price remains the same, only the shipping increases.

Used driver side upper front fender nose section. Rust free with no prior damage. Cut with a plasma cutter behind the leading edge of the wheel well. There are minor differences between the 71, 72 and 73 Fenders, but this fender nose section is the same for all three.

Used passenger side upper front fender nose section. Rust free with no prior damage. Cut with a plasma cutter behind the leading edge of the wheel well. There are minor differences between the 71, 72 and 73 Fenders, but this fender nose section is the same for all three. ...

Here is our used 1971-73 lower rear window channel which we will cut to suit your needs. Quite often vinyl tops will cause rust in this area and this part is cut from a rust free Western parts car. Tough to find rust free, Ford installed the trunk lid gasket to the surface of the trunk opening. There may be a bit of erosion or pitting, we have very few remaining on our relatively rust free cars due the to layout of the trunk gasket. If you need the package tray attached there is no extra...

Rear license plate and fuel door hinge pin for 1967-68 and 1971-73 Cougars and 1968-71 Ford Fairlane and Torino models, excluding station wagon and Ranchero. One pin for each side of the hinge, sold individually. Replaces Ford part # C6OZ-13432-A.

Used door hinge anchor plate for attaching the door hinge to the body pillar. Driver side lower only, marked with an "L". Fits any 1971-73 Mercury Cougar and Ford Mustang.Ford part number C6OZ-6202639-A.

Used door hinge anchor plate for attaching the door hinge to the body pillar. Driver side upper only, marked with an "L". Fits any 1971-73 Mercury Cougar and Ford Mustang.Ford part number D1ZZ-6502667-A.

Used door hinge anchor plate for attaching the door hinge to the body pillar. Passenger side lower only, marked with an "R". Fits any 1971-73 Mercury Cougar and Ford Mustang.Ford part number C6OZ-6202638-A.

Used door hinge anchor plate for attaching the door hinge to the body pillar. Passenger side upper only, marked with an "R". Fits any 1971-73 Mercury Cougar and Ford Mustang.Ford part number D1ZZ-6502666-A.

Floor tunnel body reinforcing plate for the floor shifter on any 1971-73 Mercury Cougar or Ford Mustang. Used plate spot welded to the underside of the floor. Has threaded inserts installed. Contoured differently than previous years. We cut, you remove spot welds. Take your measurements for location, before removing your old floor and or tunnel.  Ford part number D1ZZ-6512118-A.

This reproduction radiator / core support assembly includes the lower crossmember and is the very best one made! The outer width on the frame rails for the hardtops is 35-1/2 inches, a convertible has a width of 35-1/4 inches. A good body man should be able to make a hardtop core support fit a convertible, but know that it is different. We generally have 4-6 convertibles on the ground in the wrecking yard at any given time, so please call 503-463-1130 for your convertible needs.Replaces Ford #...

These are bolted to the rear frame rails and were used to tie the car down to the transporter for the journey from the factory to the dealer. The dealer was supposed to remove them and return them for a credit as instructed by the dealer. Notice the sticker on the rear license plate frame (decal is available in the decal section)? Many sets slipped through as the dealers often forgot or did not deem the small credit back worth their effort to remove. These are great for transporting your car...

Late 1971 (4-1-1971) through mid late 1972 Mercury Cougar, approximate cutoff is 3-1-1972. Look for two different things to differentiate the trunk lids. First is the spacing on the bolts to the hinges. This style has a 4-1/4 inch spacing, early 1971 deck or trunk lids have a 3 inch spacing on those hinge bolts. The seconde is the style of deck / trunk lock cylinder attachment. D1WY-40110-B style has the internal style of keeper for the trunk lock cylinder. These deck / trunk lids do not have...

1971 until about 4-1-1971 Mercury Cougar. Look for the spacing on the bolts to the hinges. This style has a 3 inch spacing, late 1971-72 deck or trunk lids have a 4-1/4 inch spacing on those hinge bolts. D1WY-40110-A style has the internal style of keeper for the trunk lock cylinder. For deck / trunk lids it is all about rust under the inner rear lip... We still check it over good for excessive filler, correct contour on all the lines and hidden rust under the weather strip. Keep in mind we...

Most often the problem with our Grade "B" deck / trunk lids is rust under the lip. We have some "B" rated deck / trunk lids with dents on the top side and no rust, so call 503-463-1130 if you have a preference. We do not sell "rotted out" deck / trunk lids. Like the deck / trunk lid shown here you will be able to sand blast it and treat the rust so as to prevent it from spreading. We almost guarantee that at least "some" pin holes will appear after you have blasted the underside. Make sure to...

Most often the problem with our Grade "B" deck / trunk lids is rust under the lip. We have some "B" rated deck / trunk lids with dents on the top side and no rust, so call 503-463-1130 if you have a preference. We do not sell "rotted out" deck / trunk lids. Like the deck / trunk lid shown here you will be able to sand blast it and treat the rust so as to prevent it from spreading. We almost guarantee that at least "some" pin holes will appear after you have blasted the underside. Make sure to...

Used trunk or luggage compartment latch, fits all 1967-73 Mercury Cougar and many other Ford and Mercury cars. Comes with 3 bolts for mounting.Replaces Ford part number C5AZ-6243200-A.

Good for all 71-73 Cougars and Mustangs. This extension extends from the driver side rear fender apron to the top of the cowl.This rear fender apron extension is a great choice for your damaged, rusted or missing panel. Made from stamped steel, just like the original. The extension fits in place between the passenger side rear fender apron and the top of the cowl. It provides for a sturdy, stable mounting area for the far rear top fender bolt and the rear hood hinge bolts. ...

Good for all 71-73 Cougars and Mustangs. This extension extends from the passenger side rear fender apron to the top of the cowl.This rear fender apron extension is a great choice for your damaged, rusted or missing panel. Made from stamped steel, just like the original. The extension fits in place between the passenger side rear fender apron and the top of the cowl. It provides for a sturdy, stable mounting area for the far rear top fender bolt and the rear hood hinge bolts. ...

Driver side, rear frame rail, from a 1971, 1972, and 1973 Mercury Cougar hard top. The Ford MPC shows a couple of different numbers and exceptions for this item. It may be the presence or absence of the nutserts for the rear sway bar option. If the sway bar nutserts are needed, please contact WCCC for availability. Full length, we cut so that there is some remaining metal on the edges. Ford part number D2WY-6510125-A.* Note - this item has dimensions in excess of 75 inches, and will ship as...

Passenger side, rear frame rail, from a 1971, 1972, and 1973 Mercury Cougar hard top. The Ford MPC shows a couple of different numbers and exceptions for this item. It may be the presence or absence of the nutserts for the rear sway bar option. If the sway bar nutserts are needed, please contact WCCC for availability. Full length, we cut so that there is some remaining metal on the edges. Ford part number D2WY-6510124-A.* Note - this item has dimensions in excess of 75 inches, and will...

Reproduction stamped steel driver side (left hand) rear inner apron for Mercury Cougar or Ford Mustang.

Reproduction passenger side (right hand) rear inner apron for Mercury Cougar and Ford Mustang.

These reproduction convertible panels only come in black and are sold as a pair. They DO NOT have the holes cut in them for the retracting seat belts, so 72 and 73 Cougar owners will need to cut these holes. In addition, you will have to cut the holes for the ashtray and power window switch or manual window crank as well as install the snaps for the top boot. This will of course require that you have your old panels to use as a guide. These panels are not as thick as the originals and if you...

Our grade "A" rear quarter panel extensions have no obvious dings, scrapes, bumper contact damage or warping due to over tightening of studs. Ford part # D1WB-6528519, Mercury MPC # D1WY-6528011-A. Do you have questions about your Cat's factory pinstriping? This link may help.

Our grade "A" rear quarter panel extensions have no obvious dings, scrapes, bumper contact damage or warping due to over tightening of studs. Ford part # D1WB-6528518, Mercury MPC # D1WY-6528010-A. Do you have questions about your Cat's factory pinstriping? This link may help.

New old stock Ford accessory cable trunk popper. Fits late 1967 - 1973 Mercury Cougar and other Ford products. Lever release, cable and hardware, NOS Ford. Detailed instructions included. Latch not included with this kit. Sorry, the way it came. This kit was a dealer sold kit or over the counter kit. Fits a large range of Ford cars. Ford part number C4AZ-62432A00-A. *Note - All 1967, and most 1968 trunk lids will not have a large enough access opening in the under side structure to...

This is the round metal threaded disc that attaches the D0ZZ-6523258-A bushing to the door glass brackets. About 1-3/4" in diameter, two each per door glass on a 1970. 1971-73 Mercury Cougar and Ford Mustang use 3 of these for retaining the door channel bracket. Ford part number 384289-S.Click on images to enlarge. Do you have questions about Glue-In vs Bolt-In glass? How about how to properly install Glue-In glass in your 1969 Cougar or Mustang? Check out our video below for some great glassy...

Retainer or keeper for door hinge pins on all 1968-73 Mercury Cougar and Ford Mustang, plus most all other Ford products with a typical door hinge pin. The factory installed the hinges with the pins driven in from the bottom as viewed with the doors installed. Most restorations install the pins from the top so that gravity holds them in. These retainers allow the pins to be mounted concours correctly. You must use a socket or other tool to install. These fit the door hinge pins with 5/16 inch...

Plastic insert with metal locking retainer. Replaces Ford part # C5AZ-6221952-A. NOTE* This clip will need to be squeezed on the clip side in order to obtain a good grip. Check out our handy diagram below to find other '67-'68 door parts you may need. All the item numbers shown can be typed in to the search bar on our site. (Click image to view full size) ...

Plastic insert with metal locking retainer. The plastic came in various colors, white, red, and black are common. Replaces Ford part # C5AZ-6221952-A.Check out our handy diagram below to find other '67-'68 door parts you may need. All the item numbers shown can be typed in to the search bar on our site. (Click image to view full size) ...

Used door lock and trunk lock cylinder retainer clip. Not exactly the same as the door lock clips. Trunk clips have the small hole, a hooked tool would be used for removal. Not used on 1967 - 1968 Cougar trunk lock cylinders. *Note - For use on Cougar trunk locks built prior to 3-1-1972. Please see Ford part number D2WY-6243629-A for your Cougar needs on cars built after 3-1-1972 (used only).

Spring steel clip located under the drive cable housing as seen on page 16, figure 19 of our free download of the sunroof panel service procedure manual.

This strip has a series of seven retaining clips that hold the headlining panel to the roof panels as seen on page 14 of the sun roof manual.

This strip has a series of five retaining clips that hold the headlining panel to the roof panels as seen on page 14 of the sun roof manual.This is for the 1971-73 Mercury Cougar with factory sunroof. Sunroof measurements are roughly 19-1/2 x 39 inches. This panel is 32-1/4 inches long with 5 clips as shown.

Great reproduction of a rather hard to find part.

We have created all of the components needed to economically install the steel nutsert or Riv-nut for the exterior mirrors that mount to the car doors. Our steel Riv-nut uses a 1/4 inch hole. You will need a 5/32 Allen or hex key, 3/8 inch wrench, and a 7/16 inch wrench. The Riv-nut needs to be assembled on the kit as shown prior to installation. The assembly is installed flush, in the pre-drilled hole. The Allen wrench and the 7/16 are held stationary, while the 3/8 wrench is used to tighten...

These vinyl coated clips hold the weatherstrip and guide the window when rolling up. Used clips usually are rusted and the vinyl portion is peeling. Two required per car.Replaces Ford part # D1ZZ-6522244. Sold individually

Reproduction roofrail weatherstrip seal clip and quarter window guide clip for the 1971

New rust treatment in aerosol form for the Mercury or Ford. Provides one-step treatment that destroys old rust and prevents new rust. Just spray it on. Within minutes, rust is replaced by a durable black polymer coating that may be painted. Excellent protective primer. Follow directions for use, wear gloves it does not wash off readily.*NOTE* This item can only be shipped via UPS ground. No Foreign orders please. ...

One size fits all.  Set of 4.  Good replacement if not worried about show quality. 1967 – 1968 Coupe 6 Required per car 1969 – 1973 Coupe 4 required per car 1969 – 1973 Convertible 2 required per car Will also work on the 69 - 73 shifter bezels. 4 required. Not recommended for our Mass Backed Carpeting. Please see related items for the longer screws. Replaces Ford Part #: 381571-S

8-32 x 1 inch long screws for attaching automatic shift bezels on 1969-73 Mercury Cougar or Ford Mustang with added Mass Backed Carpeting. Shiny zinc screws as shown, set of 4. Replaces Ford Part #: 381571-S

When it's time to replace your old decaying foam seal, go with our reproduction weatherstrip retainer foam roll with peel off adhesive. Goes between the roof and door / window channel.  These are not technically manufactured to fit the Cougar / Mustang, however these are very close to the originals and come from the manufacturer in a roll that is 4' X 1" X 1/8".  One roll is more than enough to do one side, but you will need 2 rolls to do both sides. ...

These are good reproductions of the originals for your American Sunroof Corporation Golde Sun Roof. The roof opening seal is 89 1/4" x 3/4" and the seal that affixes to the rear edge of the roof panel measures 42 1/2" x 3/4". These have the correct aluminum inner core with rubber bead, wrapped in the correct felt textured, black material. They're are made by the original manufacturer in Germany and will fit all Cougars equipped with the ASC sunroof. Very hard to find seals at a reasonable...

Premium reproduction rubber seal with the proper thickness of the 1967-68 seal as found on Mercury Cougar and Ford Mustang except these are not molded to the extension contours. Starting in 1969 this channel seal was manufactured slightly smaller which tightened up the gap on the fender and quarter extension seals. This seal maintains the slightly larger gaps. Sold as a pair, two pairs needed per car.  Each package has 2 strips of 25 1/2" lengths. *NOTE* Do not over tighten the...

Used seat belt anchor plate that has been cut out from a car in our salvage yard. Must be welded to floor pan. 6 total per car, 2 inboard in the transmission tunnel, and 4 on the rear seat pans. The front outboard anchors are part of the rocker rails. Rectangular shaped like the 1967-73 cars. We have noticed that the last generation 1971-73 Cougars had 4 round shaped plates in the rear floors. Same threads, all work the same. These were pretty much used on all Ford cars starting in...