Engine & Under Hood

Grade A exhaust manifold heat shield for any 1970 Mercury Cougar or Ford Mustang with 351C engine, 2V or 4V, it doesn't matter. Uses a separate, small diameter metal tube (part number D0OZ-9652-A) that attaches to the 1970 Cleveland air cleaner snorkel. Grade A used will only have minor pitting, it will have no holes or rough rusted edges. We also stock B grade versions for less than half the money.Replaces Ford part number D0OZ-9A603-F.

Used grade "A" heat shield for the Mercury Cougar or Ford Mustang equipped with either the H code 2V or M code 4V 351 Windsor engine. This metal shroud and tube assembly attaches to the factory air cleaner assembly and really finishes off the engine bay. Ford part # C9OZ-9A603-A.*NOTE* For 1970, this shield was used after the build date of 2/2/1970, but it can also be used on prior dates. We suspect that the early 2 piece shroud was discontinued because of rattling noises or some...

C8OZ-9A603-B metal shroud that attaches to the passenger side stock cast iron exhaust manifold. Works in conjunction with a metal 'S' tube sold separately (C8AZ-9652-A). R code and Q code Cobra Jet engines only.

Ford part number C9ZZ-9A603-C for the upper section and C9ZZ-9A603-D for the lower for this two piece metal shroud unique to G code Boss 302 Cougar Eliminators. *Note - Very early 1970 Boss 302 cars build prior to 9-2-1969 used this lower section also. metal shroud unique to G code Boss 302 Cougar Eliminators. *Note - Very early 1970 Boss 302 cars build prior to 9-2-1969 used this upper section also.

Ford part number D0ZZ-9A603-C for the upper section and Ford part number D0ZZ-9A603-D for the lower section of this two piece metal shroud unique to G code Boss 302 Cougar Eliminators. *Note - 1970 Boss 302 cars build after 9-2-1969 used this lower section. of a two piece metal shroud unique to G code Boss 302 Cougar Eliminators.

This is for you folks out there who want the correct part number on your hinge. Good used OEM original hood hinges that are available individually or as a set. We now offer a PREMIUM quality reproduction that is superior to any other reproduction. We carefully inspect these hinges before sending them as used hinges are prone to wear in more than one area. Here is a helpful youtube video that shows you how to adjust your hood. Shipped without the spring. These will also work on 1967-70 as well....

This item has been discontinued until further notice.Basically correct looking except for screws in place of the rivets. The High or Low tone is indicated in raised letters located on the perimeter of the horn. Replaces Ford Part #: C9ZZ-13832 / C9ZZ-13833 or C9ZF-13801-B / C9ZF-13802-C.

Tested and working used Lo tone horn. The Lo tone is indicated in raised letters located on the perimeter of the horn. 1969-70 Mercury Cougar and Ford Mustangs used part number C9ZF-13802-C Lo tone. Every horn is bench tested and inspected for cosmetic defects, if they do not function properly, and pass a visual inspection, they get recycled. The used horns at WCCC can be used as-is or you can clean and detail them for you show car.

D0AZ-6A664-C Original used hose that connects the valve cover mounted PCV valve and the carburetor spacer plate on 1970 Mercury Cougar and Ford Mustang 351 Cleveland engines both 2 and 4 barrel versions."L" shaped hose, 1/2" in diameter, approximately 15-1/4 inches long. Used hoses will have faded striping (if present), and clamp impressions. Very often the rubber will be hard and showing some degree of stress cracks. *Note - Excludes 1969-70 351W or Windsor engines. *Note - These molded and...

C9OZ-6A664-A Original used hose that connects the original PCV valve to the carburetor spacer plate. All 1969-70 351 Windsor 2V and 1969 351Windsor 4V engines. Used hoses will have faded striping (if present), and clamp impressions. Very often the rubber will be hard and showing some degree of stress cracks. This hose is a bit longer than the 289/302 version due to the taller deck height of the 351 Windsor engines. *Note - These molded and contoured hoses were designed to work with the...

D0ZZ-6A664-A Original used hose that connects the original threaded PCV valve combination with C7OZ-6A706-A elbow and the carburetor spacer plate. Molded hose with 5/8" valve end and 3/8" spacer plate end. 1970 428CJ and 428SCJ engines, includes Cougar and Mustang only. Used hoses will have faded striping (if present), and clamp impressions. Very often the rubber will be hard and showing some degree of stress cracks. *Note - Excludes 1967-69 S code 390-4V and 1968-69 428CJ engines. See part...

C8OZ-3C511-B Rear power steering pump support bracket. Also called the high pressure hose indexing bracket. For any 1968 - 1970 Cougar or Mustang with any of the 390 / 427 / 428CJ engines. OEM used part designed to maintain the position of the high pressure power steering hose from coming in contact with with moving or high heat parts. *Note - May or may not work with non-original or replacement high pressure hoses.

D0ZE-9425-E Cast aluminum intake manifold used on all 1970 G code Boss 302 engines in a Mercury Cougar or Ford Mustang. Stock 4 barrel intake manifold. Take off manifold with correct casting number of D0ZE-9425-E . Intake shipped bare, less carburetor studs, heater tube, vacuum fittings, and water neck where applicable. Ford master part number C9ZZ-9424-D or -E.

Rechromed GT air cleaner lid for the Mercury Cougar and Ford Mustang equipped with either the Boss 302, GT 390, or 428 CJ engine without the shaker option. It was possible to order a 390 GT motor for your Cougar without ordering the 390 GT package. Cougars equipped with the S code 390 6.5 Litre engine, that did not come with the GT package, would have used the painted air cleaner lid. Replaces Ford part # C7OZ-9661-A.*NOTE* The outside dimension of the lid is 16.75 inches and will not fit the...

This is a 1969 lid. The 1968 lid had several differences, most notable was the stamping wrinkles. This is  Flapper mid plate for use on non-shaker cars. 1969-70 Mercury Cougar with R or Q code engine with ram air. 1969 Mercury mid sized cars such as Montego, and Cyclone all with R code 428CJ or SCJ engines. Ford part number C9ZA-9600-C. This version is said to have been used starting in May of 1968, so there would have been some cars equipped with this mid plate.There are many...

This engine compartment lamp assembly includes lamp socket, bracket, mercury switch, and length of wire. Replaces part # D0WY-15702-A

NOTE: WE SUGGEST LOCAL PICK UP ONLY FOR CORE ENGINE BLOCKS BECAUSE WE CANNOT GUARANTEE BLOCKS WILL NOT HAVE CRACKS INTERNALLY. Long block, factory H code 351-2V V-8 engine. 351 Cleveland engine rated at 250 Hp with 9.5:1 compression ratio in 1970. Likely 0.030" bored motor that may or may not have been in running condition when pulled. Guaranteed to be rebuildable. Complete engine less carburetor, distributor, exhaust manifolds, fan, accessories, pulleys, and flex plate. Intake manifold and...

D0ZZ-9A820-B Distributor modulator lower speedometer cable for 1970 Mercury Cougar and Ford Mustang with the M code 351C-4V engine and FMX or automatic transmission. Used on cars manufactured before 12-15-1969. Long cable that connects the speed sensor and the FMX transmission of the modulation system. Shown to be 45.25 inches long. Please see D0ZZ-9A820-H for the upper cable section. Please see D0ZZ-9A820-G for cars manufactured after 12-15-1969.

D0ZZ-9A820-G Distributor modulator lower speedometer cable for 1970 Mercury Cougar and Ford Mustang with the M code 351C-4V engine and FMX or automatic transmission. Used on cars manufactured after 12-15-1969. Long cable that connects the speed sensor and the FMX transmission of the modulation system. Shown to be 49.24 inches long. Please see D0ZZ-9A820-H for the upper cable section. Please see D0ZZ-9A820-B for cars manufactured before 12-15-1969.

Cast iron pedestal mount for the air conditioning compressor on all 1970 Mercury Cougars and Ford Mustangs with the 351W H code 2V engine. Ford also used this bracket on other 1970-71 Ford passenger cars with 351W engines only.Ford casting number D0AA-2882-E.

Cast iron construction similar to the 1969 bracket but with a design change for 1970. We suspect that the change was made for the new pulley and bracket arrangement starting in 1970. Ford part number D0ZZ-9B450-B.

Special rear mounting bracket for 1970 Boss 302 Cougar Eliminators and Ford Mustang. Triangular shaped bracket as shown. Ford part number D0ZE-10A336-A.

D0ZZ-9D664-A Bracket for mounting the charcoal canister to the body. Application - all 1970 California sold Mercury Cougar and Ford Mustangs. Some Ford illustrations show a casting number of D0ZF-9D664-A

Application is for the FE engines 390, 427 428. This assembly is needed for the installation of the cylinder head air supply tubes. Sold as one nut / one ferrule. 8 total needed for smog tube attaching. Originally these were installed in conjunction with a lower tube.

New rubber "O" ring for Ford V-8 distributors from 289/302/351W/351C/429 engines.

Used 1970-72 black AUTOLITE marked oil fill cap with black plastic elbow. Several variations noted from our collection, AUTOLITE and MOTORCRAFT versions. Will need detailing or fresh black paint applied. Would also suggest replacing the rubber grommet. These 50 year old rubber grommets are rock hard and likely leak air. Gasket to valve cover will also need replacement. Even though this cap has a 1971 parts number, we see these on the 1970 351C engines quite often. Replaces Ford part...

Precision machined to the factory specifications. Light gold anodize finish just like the original.

Factory oil cooler as used on 1969-70 R and Q code Super Cobra Jet 428 engines. Nice used condition, comes as shown with one fitting. Will also work for installing an external oil cooler on the other FE motor applications.Ford part number C9OE-6884-B. 

Nicely chromed dipstick tube and dipstick for the Mercury Cougar or Ford Mustang equipped with the 351 Windsor. Replaces Ford part # C9OZ-6750-A or D0AZ-6750-C.

Chromed engine oil dipstick as found on all 1970 Mercury Cougar and Ford Mustang with 428CJ engines (Q or R Code). Top of shield to dip stick is 20 inches. The handles were chromed originally. Ford part # D0OZ-6750-C, Ford casting # D0OE-6750-C.*NOTE* This is an improved dipstick that better reflects the actual full mark, from previous 428CJ dipsticks.

Chromed engine oil dipstick as found on all 1970 Mercury Cougar Eliminator and Ford Mustang with Boss 302 engines (G Code). The handles were chromed originally. Ford part # D0ZZ-6750-B, Ford casting # D0ZE-6750-C.

Reproduction blue dipstick tube for the Mercury Cougar or Ford Mustang equipped with the 351 Windsor.

This oil filter is absolutely concours correct. A must for Show. All are silk-screened with multiple colors.

The oil filter made by the original Ford supplier.

New Old Stock oil filter adapter from any 1968-70 Ford with 390 or 428CJ (non SCJ). Fits Cougar, Mustang, Torino, Fairlane, Cyclone, Ranchero, etc. Nice cast aluminum bracket for installing the spin on oil filter and oil pressure sending unit. Ford casting number C8AE-6881-A. Will fit 1967 FE engine blocks too. Those technically used an adapter with a casting number of C0AE-6881-A.

A nice reproduction oil pan in Chrome finish for the 351C. Replaces Ford Part #: D0ZZ-6675.

Famous 'Cal Custom' aluminum finned oil pan that was so popular throughout the 60's, 70's and 80's. It has not been available for years, but it is back again. Pan is made from all new pressure die cast tooling and then fully machined to offer a precise fit and leak free installation. These look great in combination with the Finned Air Cleaner and Valve Covers. Replaces Ford Part #: C5ZZ-6675.

Includes drain plug.

Used oil screen pick up tube assembly from a 1970-74 small block 335 series, or 351C or Cleveland Ford car. This is for front sump oil pans. Used item, should be degreased and cleaned inside and out prior to installation. Tube assemblies with damaged screens, damaged tubes or bends are thrown away or scrapped. We only save undamaged, used oil pick up tubes. Melling sells a quality reproduction of this item. Replaces Ford Part #: D1AZ-6622-A

Used oil screen pick up tube assembly from a FE or big  block 1966-70 Ford car, such as 352, 390, 410, 428, or 428CJ engine. This is for most front sump oil pans. Used item, should be degreased and cleaned inside and out prior to installation. Tube assemblies with damaged screens, damaged tubes or bends are thrown away or scrapped. We only save undamaged, used oil pick up tubes. Melling sells a quality reproduction of this item. Replaces Ford Part #: C6OZ-6622-A ...

New pair of white and yellow paint sticks for the Mercury or Ford. These units were used by FORD at the assembly plants to mark fender aprons

New old stock brass intake manifold fitting that screws into the rear of the 428 CJ intake manifold on all 1969 428 Cobra Jet engines. Similar to the 1967-68 version, but this one has an additional smaller nipple coming out of it.  Ford part number C8OZ-9A474-A.

Used threaded PCV valve for use on 390-4V, 428CJ, 427-4V cars from 1967-70. Unknown functioning condition, these have the correct threaded tops and work with either of the 90° elbows available, reproduction or OEM Ford.

New air cleaner breather element for all 1970-73 Mercury Cougar and most all Fords with V-8 engines. This filter fits inside your air cleaner base, a hose connects to the fitting and goes to the PCV valve in the valve cover. Sold as shown, includes cartridge holder, retainer clip and filter.

Pertronix brand 7mm spark plug wires. These are performance oriented wires compared to the concours spark plug wires. For any 1967-73 Mercury Cougar and Ford with 289 or 302 engines. Black wires and boots, quality spark plug wires taylor made for the small block Ford engines. Recommended by Pertronix for use with the Flame Thrower coils.

Good used single sheave pulley for the alternator on the Boss 302. Ford Part #: C5AF-10A352-H.

C9AF-10A352-A or -B Alternator pulley for use with only one drive belt. Just under 2-3/4" inches in diameter. This later version would have a casting number of C9AF-10A352-A or possibly C9AF-10A352-B stamped on it. Ford master part number is C5AZ-10344-K like the above pulley.

D0OE-6312-C For both Cleveland and Windsor 351 engines. This is also the "with air conditioning" pulley, but with power steering option. Triple sheave 8.00", 7-55/64", 6-9/16" diameters. A four bolt hole crank shaft pulley for use with 1970 and upward crank dampeners. Ford Master Part number D0OZ-6A312-B. This is a Service Replacement pulley for D0AE-6312-C. *Excludes 1972 Q code 351 Cobra Jet engines. This means all 1972 351C-4V engines.