Fasteners

Fits Standard and XR7

Used Strap - Large Wire Loop for the 1968 Mercury Cougar or 1968 Ford Mustang

Universal wire loom plastic clip for any application on Cougars or Mustangs, as well as many other models.5" x .26"

This nut fits onto the strut brace at the front of the car, and not the control arm end. It is the lock nut that goes on after the the bigger strut rod bushing nut.Replaces Ford part # 340460-S

This nut fits onto the strut brace at the front of the car, and not the control arm end.Replaces Ford part # 380517-S

Reproduction 8-32 x 1/2" stud used to attach the convertible boot mouldings on any 69-73 Cougar or 65-73 Mustang. A number of these studs were installed on the mouldings, going through the body of the car and attached underneath the sheet metal using the boot nuts.

Stud for attaching heat shield to passenger side exhaust manifold. Fits all 1968 Mercury Cougar or Ford Mustang and other Ford too. Sold individually. Phosphate & Oil (gray-black)

Reproduction Tail Light / Trunk Light / Courtesy Light Loom Clip for the 1967 - 1968 Mercury Cougar or Ford Mustang 

New blue removable strength thread locker for your project. This is a must have item if you are reassembling your pride and joy after restoration or just changing out parts. Often times, the vibrations from these antiques can vibrate loose the fasteners used to hold it together. If you use this, you can rest assured that your Merc or Ford will not fall apart from fasteners that have vibrated loose.

New red permanent strength thread locker for your project. This is a must have item if you are reassembling your pride and joy after restoration or just changing out parts. Often times, the vibrations from these antiques can vibrate loose the fasteners used to hold it together. If you use this, you can rest assured that your Merc or Ford will not fall apart from fasteners that have vibrated loose.

Sold individually Zinc (dark silver)

1967-68 XR7 over head console pad clip. Two needed per car. Sold individually # C3AB-63519A16

Seven (7) of these acorn nuts are used to hold the trunk trim moulding on to the trunk. Replaces Ford Part # 377767 For more insight on this tricky trunk trim, check out our video below: ...

Sold individually, two per side, four per car required. These often get destroyed when you go to replace your door window regulator slides. Two of these are used to install the C7ZZ-6523288-A track. Check out our handy diagram below to find other '67-'68 door parts you may need. All the item numbers shown can be typed in to the search bar on our site. (Click image to view full size)Not sure where to begin when it comes to replacing your window regulator? Check out our how-to video...

Almost identical to the original, tab is a bit longer. *NOTE*1969 Cougar owners do not need this part as it is built in the the chromed plastic, rectangular bezel on the door panel.

This is the rubber spacer / washer that goes between the bolt head and the metal washer of your seat belt hardware. The purpose of the rubber washer is to dampen any vibrations caused by the movement of the seat belt.Sold individually# 354959-S

Reproduction steering gear or seat belt washer for the Mercury Cougar or Ford Mustang. These units are sold individually.Replaces Ford part # 378580-S.

Used on the retractors.

These spacer / washers were used on the rear belts of 1968 - 1973 Cougars. 1968 used two per bolt for a total of eight, 69-71 used one per rear belt for a total of four and 72-73 used one per belt on the inner only as the outer belts had a re-tractor in the rear 72-73. They were red to guide the line workers on placement.

These spacer / washers were used on the rear belts of 1968 - 1973 Cougars. 1968 used two per bolt for a total of eight, 69-71 used one per rear belt for a total of four and 72-73 used one per belt on the inner only as the outer belts had a re-tractor in the rear 72-73. They were red to guide the line workers on placement. Sized like the originals, but do not have the dimples all over. 0.53" ID x 0.88" OD.

Same as 69-73 but with no markings.

Wave locking washers for the door hinges on the 67 - 70 Cougar or Mustang. These washers have teeth that will dig in and hold tight, making sure your door hinges never come loose.

Sold individually, phosphate & Oil (gray-black).

A nice reproduction of the standard air cleaner wing nut. This version was used on most Ford products through the 1980's.

Reproduction Wire Loom Mounting Kit for the 1968 Mercury Cougar / Ford Mustang

Master clip kit which includes following fasteners: Driver side apronEngine feedFirewallFront crossmemberGas tank senderHorns and regulatorPassenger side apron below relayRadio cable to dashKeep in mind that there are many other fasteners on 1968 Cougars / Mustangs that are not in this kit.

Replaces Ford Part # C8AZ-2B164-A Sold individually

Four per car unless you have a 1968 decor or standard model that has the unique three hole armrest and then you will need six. Replaces Ford part # C7AZ-6224146. Check out our handy diagram below to find other '67-'68 door parts you may need. All the item numbers shown can be typed in to the search bar on our site. (Click image to view full size) ...

Reproduction disc brake hose bolt for any 1968-73 Mercury Cougar and generally all other Ford cars with factory disc brakes. Special hollow bolt with cross drilled hole. Attaches the high pressure hose to the caliper.

These Spark Plug Wire Separators are made of high-quality ABS plastic. Constructed to hold both standard 7mm and 8mm high-performance spark plug wires. Fits directly on valve cover clip. Available in blue, red and OE black.

Inner front bolt, long length to clear sound deadener. Used in conjunction with a thick, gold spacer washer.

Rear seat belt bolt, four per car used in conjunction with two red washer / spacers. 13/16" hex head, 1-1/4 inch bolt with a 3/16 inch shoulder. Can be either smooth headed or have a Heavy or Light "A". There is another version of this same bolt with a smooth head and no markings.

Used Vent Frame Bolt Kit 1967 and 1968 Mercury Cougar and Ford Mustang.Consists of: 1 bolt - 379384-S2 1 bolt - 378694-S 2 lock nuts - 33797-S2 set screws -  375694-S2

This is the Water Pump Bolt Kit for 1967-68 Mercury Cougar and 1965-68 Ford Mustang with the 289 or 302 engines without air conditioning. This kit includes the 11 bolts needed to mount the water pump to the motor.  This kit comes with an instruction sheet, and shows the correct placement of the bolts.

Reproduction set of four 2 3/4" black phosphate bolts for the 2 1/4" fan spacer on the 67 - 73 Cougar or Mustang.

These reproduction hood latch catch bolts fit both the Standard and XR7.

Stamped steel construction with black vinyl coating like the original to prevent corrosion. Please note that vinyl coating will almost always crack along edges shortly after installation, just like the originals did... This is the same exact hold down you will see listed elsewhere its just that we feel you should know what you are getting up front so you will not be surprised. Replaces Ford part #: C5AZ-10718-A.

Two of these clips per side are required to hold the interior padded pillar pads the the "A" pillars on your 1968 Cougar.Replaces Ford part number 381896-S2.

Delicate clip that attaches to a nail-head stud attached to the firewall. Very functional and visible, rather hard to find in unbroken condition.

Used plastic clip for the Mercury Cougar or Ford Mustang.

Reproduction of the plastic square hood insulation clips. 11 used on most vehicles. Sold individually.

New replacement J-nut or they are sometimes called U-nuts. These clip into those square holes in the fender aprons for fastening the fenders on 1967-70 Mercury Cougar and Ford Mustangs. These clips are 5/8 inches from the hole center to folded edge. We also see the same clips with 27/32 inch spacing for fender mounting. Numerous other uses, we find this clip on the hidden headlight buckets on 1967-68 Cougar and XR7's.

This kit is the same Scott Drake "Shelby Style" DELUXE hood pin kit offered by many other vendors.Kit includes 2 Hood Pins, 2 dowel pins, 4 Nuts to hold the dowel pins on, plates for the top of the hood, 8 screws to hold the hood plates on and 2 tie down cables. The difference between the standard version and this deluxe version, is that the standard is chrome plated and the deluxe is stainless steel. Common consensus is that the holes for the pins were hand drilled at the factory, so the...

Used set of four nuts and two locking washers used on the knob shafts of all radios 1967 - 1973 used on Cougars, Mustangs, Galaxie, Torino etc.

This clip secures the clutch pedal rod end as it comes through the clutch pedal hanger.C8AZ-2B277-A

This fits behind the door panel and is needed to install your remote mirror correctly.*NOTE*1969 Cougar owners do not need this part as it is built in the the chromed plastic, rectangular bezel on the door panel.

Reproduction hold down clamp rivet for the 67 - 73 Cougar or Mustang. This rivet holds the clip / clamp onto the distributor. Sold individually, 2 per car.

Concours? almost, these are stainless steel screws with the wax tipped coating like the originals, for installing the door sill plates. The wax was deemed necessary by the Ford Motor Co. as a seal. These can be used on all years 1967-73 Mercury Cougar, Ford Mustang and most all other Ford, Mercury, Lincoln cars of the era. Works well with any of the reproduction sill plates, these were really made to be used with the premium reproduction sill plates in stainless steel. 1967-68 Cougar and...