All Available Parts - 1971 Ford Mustang

These are the screws that secure the door latch mechanism to the door shell. These screws come with the attached crown headed lock washer, just like the originals, so be sure to tighten them down snugly to ensure that the screw head sits flush into the screw holes. Sold individually. Three required per door, six per car.

Door lock latch lever, for driver or passenger side locks. Attach with an "E" clip on the rear side of the lock mechanism. Used "E" clip is included. We are going to say that these fit all Ford door locks 1965 through 1973 and beyond. *Note you will need to purchase or reuse your retainer clip for attaching the lock rod. Retainer clip not included, we have good used or reproduction clips, see related items.Ford number stamped C5AB-6221970-A or D2AB-6221970-AA  ...

Latch rod that links the door latch and the inside door handle, passenger side door. Fits any 1971-73 Mercury Cougar and Ford Mustang. Normally this rod was fabric covered. Used rod only, no retaining end clips.Replaces Ford part number D1ZZ-6521940-A.

Latch rod that links the door latch and the inside door handle, driver side door. Fits any 1971-73 Mercury Cougar and Ford Mustang. Normally this rod was fabric covered. Used rod only, no retaining end clips.Replaces Ford part number D1ZZ-6521941-A.

When ordering this item, you do not need to order a key blank, the key is included. If you need more than one key, you don't need to pay for multiple key cutting services, just buy extra blanks and mention it in the comment section of your order. This listing is for the ECONOMY version of the trunk / glove box key. We now have the ability and equipment from an old Lincoln Mercury dealership to cut keys for Fords "by the numbers". Instead of copying a worn key to make yet another key that...

Good used drivers side door latch for inside the door. Fits any 1971-73 Mercury Cougar and Ford Mustang. Comes as shown, we also have latch rods, fasteners, etc in the related items. Replaces Ford Part #: D1ZZ-6221813-A

Good used drivers side door latch for inside the door. Fits any 1971-73 Mercury Cougar and Ford Mustang. Comes as shown, we also have latch rods, fasteners, etc in the related items. Replaces Ford Part #: D1ZZ-6221813-A

Refurbished pair of door lock cylinders and ignition cylinder for all double cut key Fords 1970-73. These are coded to the original key code, which was stamped onto one of the door lock cylinders. Sometime after 1973, Ford changed the ignition lock cylinder end. We know it works through 1973, not sure of the change. It must fit the brass lock gear at the bottom of the cylinder hole in the side of the steering column. Refer to your shop manual for removal and installation. Includes two...

When ordering this item, you do not need to order a key blank, the key is included. If you need more than one key, you don't need to pay for multiple key cutting services, just buy extra blanks and mention it in the comment section of your order. We now have the ability and equipment from an old Lincoln Mercury dealership to cut keys for Fords "by the numbers". Instead of copying a worn key to make yet another key that doesn't fit properly, we can cut keys as they would have come from the...

One size fits all.  Set of 4.  Good replacement if not worried about show quality. 1967 – 1968 Coupe 6 Required per car 1969 – 1973 Coupe 4 required per car 1969 – 1973 Convertible 2 required per car Will also work on the 69 - 73 shifter bezels. 4 required. Not recommended for our Mass Backed Carpeting. Please see related items for the longer screws. Replaces Ford Part #: 381571-S

Nice reproduction of the outer door handles for the 1971, 1972 or 1973 Mercury Cougar. Replaces Ford Part #: D1ZZ-6222404-A or D1ZZ-6222405-A.

8-32 x 1 inch long screws for attaching automatic shift bezels on 1969-73 Mercury Cougar or Ford Mustang with added Mass Backed Carpeting. Shiny zinc screws as shown, set of 4. Replaces Ford Part #: 381571-S

This is the round metal threaded disc that attaches the D0ZZ-6523258-A bushing to the door glass brackets. About 1-3/4" in diameter, two each per door glass on a 1970. 1971-73 Mercury Cougar and Ford Mustang use 3 of these for retaining the door channel bracket. Ford part number 384289-S.Click on images to enlarge. Do you have questions about Glue-In vs Bolt-In glass? How about how to properly install Glue-In glass in your 1969 Cougar or Mustang? Check out our video below for some great glassy...

57084-S Attaching bolt with 7/16" hex head and captured washer. Among other things, it is used to attach the door run, window stops (all 3), both window stabilizers, and the window regulator. Same bolts for manual and power window regulators. Bolt sold individually, there are a good handful in each door. This bolt is used for bolting in the bolt-in glass on 1970, lower "L" bracket for rear quarter windows on 1971-73 Cougar and Mustangs.

Almost identical to the original, tab is a bit longer. *NOTE*1969 Cougar owners do not need this part as it is built in the the chromed plastic, rectangular bezel on the door panel.

Great reproduction of a rather hard to find part.

Good quality but not as good as original in that it is too shiny. Fits Coupe or convertible, left or right. Sold individually. Ford emblem sold separate. Replaces Ford part # D1ZZ-6513298-A

Good deal for the guy missing a sill plate on a driver. Sold individually.

Reproduction stainless steel scuff / sill plate. Fits Coupe or convertible, left or right. Sold as a pair. Ford emblem sold separate, find it here. Replaces Ford part # D1ZZ-6513298-A

*NOTE* EARLY 69's USED THE 2112 MIRROR FOR BOTH PASSENGER AND DRIVER SIDES. LATE 69's USED TWO DIFFERENT SIZES FOR EACH SIDE (2124 for driver side, and 2112 for passenger side). BEFORE ORDERING, PLEASE CHECK YOUR DIMENSIONS AND COMPARE TO OUR LISTINGS. Precision cut replacement lens for any Ford product with sport mirror on the passenger side. This fits any FoMoCo Sport mirror 69 and up, left hand only. Comes with two round pieces of double sided tape. Keep in mind if your lens is bad and it...

Reproduction side view mirror screw. These screws are sold individually. Do you have riv-nut questions? Here are riv-nut answers!

Reproduction passenger side (right hand) sport mirror lens for the Mercury Cougar or Ford Mustang and Torino.The mounting screw, that holds the mirror assembly in, is not included by default but is an optional addon. Replaces Ford part # C9AZ-17698-B. Dimensions: 4 7/16" x 2 15/16" This version does NOT include the wording "objects in mirror are closer than they appear". We also sell the version with the wording. Do you have questions about installing a passenger side mirror or using...

Empty shell / head / housing only for a passenger side manual adjust mirror. Found on all FoMoCo products utilizing a manual mirror 1969 - 1973. The remote mirror heads found on many 1970's Ford products do not interchange with the manual "Bullet Style" mirrors. Most customers find our reproduction unit to be a better value as it comes with the mirror and mounting hardware. Do you have questions about installing a passenger side mirror or using Riv-Nuts? Have more questions about installing a...

Lens with mounting hardware only for a passenger side manual adjust mirror. Found on all FoMoCo products utilizing a manual mirror 1969 - 1973. The remote mirror lens assemblies found on many 1970's Ford products do not interchange with the manual "Bullet Style" mirrors. Count on the glass being scratched. The value here is in adjustment / mounting hardware. This unit will be guaranteed to keep its adjustment and not be loose like many have become over the years. Keep in mind this item is...

Pan head screw for attaching the sport mirror glass assembly into the passenger side painted sport mirror head. Found on all FoMoCo products utilizing a manual mirror 1969 - 1973. 8-32 pan head screw with Phillips screw head. Do you have questions about installing a passenger side mirror or using Riv-Nuts? ...

Set of 20 replacement staples for the beltline kit. These are used to attach the beltline pieces to the door panel. Will work for any beltline kit on a number of different makes and models.

This cut to fit 4" pin will fit any 67 - 73 Cougar hinge upper or lower. Sold individually, four required per car. Check out our hinge rebuild video below for more info.

Most times when your door sags you do not need new hinges but rather pins and bushings. If your holes are reemed or "hogged out" you will need to buy new hinges or our good used hinges that come with new pins and bushings. Sold individually, eight required per car. I.D. 11/32"O.D 7/16" These bushings are not the same as those offered by some of the "Discount Mustang Shops".  Several of the reproductions of this bushing are too large diameter and require you to drill out your hinges...

These original hinges have been rebuilt with steel sleeves to retain the over-sized oil impregnated bushings. They feature hollow hinge pins which allows grease to fill the steel tube, lubricating the bushings under pressure from the inside-out. The threaded Zerk fittings are easily accessible from inside the car when the door is opened and are guaranteed to NEVER wear out or we will rebuild them for FREE! This offer has been in place for 20+ years by our rebuilder and they have never been...

Includes 4 cut to length hinge pins and 8 hinge bushings. Replaces Ford Part #: C9ZZ-6522800

We highly recommend restoring our rust free Western hinges over using reproduction hinges. The main reason the originals are better than the Taiwan made reproductions is fit. If there is anywhere in which you want a precision fit it is in the hinges. These hinges have not been worn to the point of being "hogged out" and have been carefully inspected for cracks. You will want to purchase a new hinge pin and 2 bushings though. Check out our hinge rebuild video below for more info. ...

We highly recommend restoring our rust free Western hinges over using reproduction hinges. The main reason the originals are better than the Taiwan made reproductions is fit. If there is anywhere in which you want a precision fit it is in the hinges. These hinges have not been worn to the point of being "hogged out" and have been carefully inspected for cracks. You will want to purchase a new hinge pin and 2 bushings though. Check out our hinge rebuild video below for more info. ...

We highly recommend restoring our rust free Western hinges over using reproduction hinges. The main reason the originals are better than the Taiwan made reproductions is fit. If there is anywhere in which you want a precision fit it is in the hinges. These hinges have not been worn to the point of being "hogged out" and have been carefully inspected for cracks. You will want to purchase a new hinge pin and 2 bushings though. Check out our hinge rebuild video below for more info. ...

We highly recommend restoring our rust free Western hinges over using reproduction hinges. The main reason the originals are better than the Taiwan made reproductions is fit. If there is anywhere in which you want a precision fit it is in the hinges. These hinges have not been worn to the point of being "hogged out" and have been carefully inspected for cracks. You will want to purchase a new hinge pin and 2 bushings though. Check out our hinge rebuild video below for more info. ...

These overseas hinges are not known for fitting well, we cannot recommend them and we do not accept returns or exchanges on them. Replaces Ford Part #: D1OZ-6522811-A

These overseas hinges are not known for fitting well, we cannot recommend them and we do not accept returns or exchanges on them. Replaces Ford Part #: D1OZ-6522810-A.

These overseas hinges are not known for fitting well, we cannot recommend them and we do not accept returns or exchanges on them. Replaces Ford Part #: D1OZ-6522800-A.

These overseas hinges are not known for fitting well, we cannot recommend them and we do not accept returns or exchanges on them. Replaces Ford Part #: D1OZ-6522801-A.

We have created all of the components needed to economically install the steel nutsert or Riv-nut for the exterior mirrors that mount to the car doors. Our steel Riv-nut uses a 1/4 inch hole. You will need a 5/32 Allen or hex key, 3/8 inch wrench, and a 7/16 inch wrench. The Riv-nut needs to be assembled on the kit as shown prior to installation. The assembly is installed flush, in the pre-drilled hole. The Allen wrench and the 7/16 are held stationary, while the 3/8 wrench is used to tighten...

*NOTE* EARLY 69's USED THE 2112 MIRROR FOR BOTH PASSENGER AND DRIVER SIDES. LATE 69's USED TWO DIFFERENT SIZES FOR EACH SIDE (2124 for driver side, and 2112 for passenger side). BEFORE ORDERING, PLEASE CHECK YOUR DIMENSIONS AND COMPARE TO OUR LISTINGS. Precision cut replacement lens for any Ford product with sport mirror. This fits any FoMoCo Sport mirror 69 and up. Comes with two round pieces of double sided tape.  Lens measures 4 3/8 X 2 7/8. Do you have questions about installing the...

Reproduction convex lens for a passenger side manual adjust mirror. Found on all FoMoCo products utilizing a manual mirror 1969 - 1973. The remote mirror lens assemblies found on many 1970's Ford products do not interchange with the manual "Bullet Style" mirrors. The screw that holds the mirror assembly in, is not included by default but is an optional addon. Replaces Ford part # C9AZ-17698-B This version included the words "objects in mirror are closer than they appear". We also sell the...

Inside door handle release mechanism for the passenger side on early 1971 Cougar and Mustang. Early because this latch mechanism went through a couple of revisions by the end of 1973. Ford calls this part a 'control and link assembly', this particular one only works with the deluxe door handles as shown in the photo. The Ford MPC describes those door handles as fitting the door panels with molded armrests, instead of the smaller detachable armrests on the base interiors. This early style was...

Plastic insert with metal locking retainer. The plastic came in various colors, white, red, and black are common. Replaces Ford part # C5AZ-6221952-A.Check out our handy diagram below to find other '67-'68 door parts you may need. All the item numbers shown can be typed in to the search bar on our site. (Click image to view full size) ...

Retainer or keeper for door hinge pins on all 1968-73 Mercury Cougar and Ford Mustang, plus most all other Ford products with a typical door hinge pin. The factory installed the hinges with the pins driven in from the bottom as viewed with the doors installed. Most restorations install the pins from the top so that gravity holds them in. These retainers allow the pins to be mounted concours correctly. You must use a socket or other tool to install. These fit the door hinge pins with 5/16 inch...

Due to the small amount of clearance between the back of your speaker and the door glass when lowered, these and the 60 Watt Kenwood version of this speaker are the only speakers on the market that will replace your worn out originals and fit like OEM without modifications. Rated at 30 watts peak power and 4 ohms.  Nice upgrade over the low wattage originals. Sold as a pair only. Replaces Ford part # C9ZZ-18808-A.   These pictures show what every 69-70 door panel looks like on the...

Due to the small amount of clearance between the back of your speaker and the door glass when lowered, these and their 30 watt little brother are the only speakers on the market that will replace your worn out originals and fit like OEM without modifications. Features Kenwood 60 watt peak power speakers, nice upgrade over the low wattage originals. Sold as a pair.   These pictures show what every 69-70 door panel looks like on the backside.  They are all perforated from from the...

These are identical on the driver and passenger sides.  Two required per car, sold individually. Dimensions: 9" x 3 1/2" Replaces part #: D2ZZ-18978.

Used original driver side (left hand) key lock to latch door lock rod for anu 1971-73 Mercury Cougar or Ford Mustang.Ford part # D1ZZ-6522135-A.

Ford calls this Rod - Door Latch Push Button. This is the driver side manual door locking rod. Side specific to the driver side on any 1971-73  Mercury Cougar and Ford Mustang. Your chromed plastic lock knob threads onto the threaded end, the lower end hooks onto the door latch. Ford part number D1ZZ-6521853-A.

Ford calls this Rod - Door Latch Push Button. This is the passenger side manual door locking rod. Side specific to the driver side on any 1971-73  Mercury Cougar and Ford Mustang. Your chromed plastic lock knob threads onto the threaded end, the lower end hooks onto the door latch. Ford part number D1ZZ-6521852-A.

Good original passenger side door latch rod set. Includes rod for inside lock, outside key lock, and outside door release actuating rod. These are good used parts and are a better quality and value compared to the reproductions. Only fits passenger side doors of 1971-73 Mercury Cougar and Ford Mustang.

Good original driver side door latch rod set. Includes rod for inside lock, outside key lock, and outside door release actuating rod. These are good used parts and are a better quality and value compared to the reproductions. Only fits driver side doors of 1971-73 Mercury Cougar and Ford Mustang.

Protects door panels from the abrasive action of rotating handles. Made from a very hard nylon type material featuring the correct milky white color. Replaces Ford Part Number #C8AZ-6223370-ADiameter 1-1/2"

This handle is a good replacement for the window cranks found on the 1971 - 1972 Cougar both front and back. The originals were 4 1/4" total length and this replacement handle is 4 7/8" long. The important detail on these is the fact that the female portion that attaches to the splined window regulator protrudes from the back 5/16". If you are using our chrome backing plates on your 69 -70, then this is the crank you will need to provide the correct clearance.Used before 10/71,...

Used on both the front and rear of the 1971-1972 Mercury Cougar produced before 10/1/71. The picture above shows the difference between the early version (right) and the later version (left). Plan on purchasing new knobs to go with the bare crank, we have 7 different colors to choose from. See related items. Inquire about a B grade knob if you are looking for something just so that you have a window crank. Ford Part # D0AZ-7630322-A, casting # as seen on the back D1AB-7630322-AWA. ...

Easy to install quality reproduction. Sorry, aqua is not available at this time. Includes crescent spring and correct aluminum pin that features shoulder and locking knurls. Fits 1968-71 cars and about 1 month into 1972. Please see the window crank handles to see the difference between 1968-71 handles and 1972-73 window crank handles. Replaces Ford Part # C8AZ-6223352 *TIP* To install remove your window crank and place knob and crank in the jaws. To protect the knob you will want to place a...

These four speed gears have the teeth reversed from the direction of the automatic gears. Made from Nylon. These gears only fit the 4 speed Toploaders. Click here to use our Speedometer Gear Calculator.   Replaces Ford Part # : C2DZ-17271-C 20 Tooth Gear Pictured

These four speed gears have the teeth reversed from the direction of the automatic gears. Made from Nylon. These gears only fit the 4 speed Toploaders. Click here to use our Speedometer Gear Calculator.   Replaces Ford Part # : C2DZ-17271-G 20 Tooth Gear Pictured

These four speed gears have the teeth reversed from the direction of the automatic gears. Made from Nylon. These gears only fit the 4 speed Toploaders. Click here to use our Speedometer Gear Calculator.   Replaces Ford Part # : C2DZ-17271-A 20 Tooth Gear Pictured

These four speed gears have the teeth reversed from the direction of the automatic gears. Made from Nylon. These gears only fit the 4 speed Toploaders. Click here to use our Speedometer Gear Calculator.   Replaces Ford Part # : C2DZ-17271-B 20 Tooth Gear Pictured

These four speed gears have the teeth reversed from the direction of the automatic gears. Made from Nylon. These gears only fit the 4 speed Toploaders. Click here to use our Speedometer Gear Calculator.   Replaces Ford Part # : C2DZ-17271-D 20 Tooth Gear Pictured

These clutch pedals feature an improved design (removable pin) for easier installation. Compatible with existing hanger assembly even in automatics. Replaces Ford Part # D1ZZ-7519-B.

D1ZZ-7519-B Good used pedal but these pedals will no doubt show some wear around the clutch rod holes. Three and four speed pedals are all the same. Mustang is the same too.

New internal speedometer gear fits 4 speed toploader transmissions. Replaces Ford Part #: C5ZZ-17285-A.

Very good quality replacement speedometer cables. 76 inches Replaces Ford Part # : C9ZZ-17260-B

Clutch Fork Pivot for Cougars manufactured after 2/16/1968. Replaces Ford Part #: C8AZ-7522-A.

C8AZ-7515-B Manual transmission clutch fork - 3 and 4 speed, stick shift transmissions. Fork measures 12-5/16 inches long. Alternate number C8AA-7515-B or C8AA-7541-B. Couple of variations of this fork. Most versions will not be stamped. Spring and side holes not needed for Mustang and Cougar applications. Originally for 1968 full sized cars with 289 or 302 engines and manual transmissions. Maybe 6 cylinders, not sure, but vert likely. Cougar 1971 - 1973, 351 Engines. Mustang 1971 - 1973,...

Backup light switch retainer for Hurst shifters as installed on 1970-73 Mercury Cougar, Ford Mustang, and most vintage Ford cars with factory installed Hurst shifters.

Backup light switch for factory installed Hurst competition shifters from 1970-73. This is a Daniel Carpenter reproduction, these are still being made by Hurst in small quantities (see our premium version). It does not include the bracket for holding the switch.Listed in the Motorcraft catalog as SW-943Also fits:CometFairlaneMontegoTorino Check out our video on rebuilding your shifter below: ...

These four speed gears have the teeth reversed from the direction of the automatic gears. Made from Nylon. These gears only fit the 4 speed Toploaders. Click here to use our Speedometer Gear Calculator.   Replaces Ford Part # : C2DZ-17271-G 20 Tooth Gear Pictured

Fits 3 speed or 4 speed manual floor shifts. Sold individually. Check out our video on rebuilding your shifter below:

Get a grip with this reproduction Hurst T handle, or shifter handle. This 1971 model is without the set-screw as found on the 1970 shifter handle. Ford part # D1OZ-7213-A. Check out our video on rebuilding your shifter below: ...

You will not need to make any modifications to run this leather unit in place of your original rubber boot used on three and four speed manual transmissions.

Chrome center cap with Red background and chrome Ford logo. Better than original! Original look wheel emblem is made from original dies. This plastic cap is painted and detailed in the original colors. This was never used on any year of Cougar but they do look good!  When using center caps on Legendary wheels, you will need these adapter plates. *Note - Certain late model disc brake rotors and aftermarket rotors have a slight clearance issue with the dust cap and these center...

Reproduction spinner cap for the Magnum 500 Legendary series wheel. Also works with the Magstar II wheel. Each spinner is die-cast with precision and finished in a show quality chrome plating. The exclusive anti-theft retainer plate keeps them in place and secure. A stamped aluminum Magnum 500 emblem and a "Bullseye" emblem are included so owners can choose which one to personalize their car with.Sold individually ...

This plastic center cap comes with each Legendary Wheel we sell at no cost. We list them for those that may lose or break one. The overall width is 2 1/2" and they are designed for a opening that is 2 3/8 " wide. Sold individually.Check out our video on Legendary Wheels below: ...

Reproduction set of 4 short valve stem assemblies for the Mercury Cougar or Ford Mustang. These new stems will look great on your Magnum, Styled Steel, Shelby, Eliminator or even stamped steel wheel.

Reproduction 15x7" Eliminator wheel with a black center and chrome rim for the Mercury Cougar or Ford Mustang / Torino. The only version of this wheel Mercury ever used on a factory order for a Mercury Cougar was a painted 14x6 with a trim ring used on the 1969 Eliminator. This black 15x7 is a really great custom made wheel that adds flash without deviating too far from the original look. As always, the cap is sold separate. Click here for the hubcap we recommend for this wheel. If you need a...

Reproduction 15x7" Eliminator wheel with a charcoal center and chrome rim for the Mercury Cougar or Ford Mustang / Torino. The only version of this wheel Mercury ever used on a factory order for a Mercury Cougar was a painted 14x6 with a trim ring used on the 1969 Eliminator. This charcoal 15x7 is a really great custom made wheel that adds flash without deviating too far from the original look. As always, the cap is sold separate. Click here for the hubcap we recommend for this wheel. If you...

Reproduction 15x7" Eliminator wheel with a silver center and chrome rim for the Mercury Cougar or Ford Mustang / Torino. The only version of this wheel Mercury ever used on a factory order for a Mercury Cougar was a painted 14x6 with a trim ring used on the 1969 Eliminator. This silver 15x7 is a really great custom made wheel that adds flash without deviating too far from the original look. As always, the cap is sold separate. Click here for the hubcap we recommend for this wheel. If you need...

These off-shore Magnum wheels are supplied to us by Scott Drake. We no longer carry the US made version as the quality was VERY inconsistent. This wheel has a 4 1/4" backspace. We now have Magnum 500 caps that feature the Mercury Logo and the walking cat caps as well. Center caps and lugs are sold separate.   NOTE! These wheels are intended to be balanced with a lugcentric adapter. They will not balance with a traditional cone spacer on the tire spin balancer. Many tire shops do not deal...

These off-shore Magnum wheels are supplied to us by Scott Drake. We no longer carry the US made version as the quality was VERY inconsistent. This wheel has a 4 1/4" backspace. We now have Magnum 500 caps that feature the Mercury Logo and the walking cat caps as well. Center caps and lugs are sold separate.  These are best suited for 1971-73 Cougars. To run a tire larger than a 225/60/15 you may have to modify your fenders and quarters.  NOTE! These wheels are intended to be...

New aluminum 15x8" Magnum 500 wheel for your Mercury Cougar or Ford Mustang. A great way to reduce the un-sprung weight on your Cat or Pony and look great while doing it! This item also includes a center cap, but they are a cheap plastic chromed cap with a blacked out center. We recommend using the adapter plates and Magnum 500 center caps we sell from Scott Drake. Lug nuts sold separately, get them here. ...

New aluminum 17x7" Magnum 500 wheel for your Mercury Cougar or Ford Mustang. A great way to reduce the un-sprung weight on your Cat or Pony and look great while doing it!  This item also includes a center cap, but they are a cheap plastic chromed cap with a blacked out center.  We recommend using the adapter plates and Magnum 500 center caps we sell from Scott Drake. Lug nuts sold separately, get them here. ...

New Legendary Series 15x7" Glossy Finish Magnum 500 wheel for your Mercury Cougar or Ford Mustang. While they look almost identical to the original chromed steel version, these are actually a lighter, better-balanced aluminum alloy with a protective coating. These wheels come with free chromed plastic center caps. The caps have a red Legendary logo but we can include at no cost, a set of black and chrome walking cat decals (click here). Just add it to your cart if you'd like these decals. If...

New Legendary Series 15x7" Satin Finish Magnum 500 wheel for your Mercury Cougar or Ford Mustang. While they look almost identical to the original chromed steel version, these are actually a lighter, better-balanced aluminum alloy with a protective coating. These wheels come with free chromed plastic center caps. The caps have a red Legendary logo but we can include at no cost, a set of black and chrome walking cat decals (click here). Just add it to your cart if you'd like these decals. If...

ETA FOR THIS ITEM IS 12/14/23Reproduction Scott Drake 16x8" Satin Black Magnum 500 wheel for your Mercury Cougar or Ford Mustang. These are the best quality of the three different Magnum 500 wheels you will find on the market today. The chrome is not only brilliant but it holds up great year after year. You may save a few dollars buying the other brands out there but why? We sell these wheels with a 4 1/2" backspace unless you specify otherwise. We now have Magnum 500 caps that feature the...

New Legendary Series 15x8" Glossy Finish Magnum 500 wheel for your Mercury Cougar or Ford Mustang. While they look almost identical to the original chromed steel version, these are actually a lighter, better-balanced aluminum alloy with a protective coating. These wheels come with free chromed plastic center caps. The caps have a red Legendary logo but we can include at no cost, a set of black and chrome walking cat decals (click here). Just add it to your cart if you'd like these decals. If...

New Legendary Series 17x7" Glossy Finish Magnum 500 wheel for your Mercury Cougar or Ford Mustang. While they look almost identical to the original chromed steel version, these are actually a lighter, better-balanced aluminum alloy with a protective coating. These wheels come with free chromed plastic center caps. The caps have a red Legendary logo but we can include at no cost, a set of black and chrome walking cat decals (click here). Just add it to your cart if you'd like these decals. If...

New Legendary Series 17x8" Glossy Finish Magnum 500 wheel for your Mercury Cougar or Ford Mustang. While they look almost identical to the original chromed steel version, these are actually a lighter, better-balanced aluminum alloy with a protective coating. These wheels come with free chromed plastic center caps. The caps have a red Legendary logo but we can include at no cost, a set of black and chrome walking cat decals (click here). Just add it to your cart if you'd like these decals. If...

New Legendary Series 15x7" Charcoal Finish Magnum 500 wheel for your Mercury Cougar or Ford Mustang. While they look almost identical to the original chromed steel version, these are actually a lighter, better-balanced aluminum alloy with a protective coating. We also have center caps for these wheels that feature the Mercury man or the walking cat logo. Center caps and lug nuts sold separately. These wheels come with free chromed plastic center caps. The caps have a red Legendary logo but we...

New Legendary Series 15x7" Stealth Black Finish Magnum 500 wheel for your Mercury Cougar or Ford Mustang. While they look almost identical to the original chromed steel version, these are actually a lighter, better-balanced aluminum alloy with a protective coating. These wheels come with free chromed plastic center caps. The caps have a red Legendary logo but we can include at no cost, a set of black and chrome walking cat decals (click here). Just add it to your cart if you'd like these...

Used steel lateral support brace for Cougars and Mustangs with the 429CJ engine. Also used on 1970 - 1971 Torinos, Rancheros, and Cyclones equipped with the 429CJ engine. Replaces part #  D0AZ-2888-A.

Used steel lateral support brace for Cougars and Mustangs with the 351-2V or 351-4V engines after 4/27/1971. Replaces part # D1AZ-2888-A.

New sealed bearing for installing on your 1968-73 Mercury Cougar or Ford Mustang idler / tensioner pulley. This bearing also came in all of the "service replacement" idler pulley assemblies and is physically larger than the idler bearing for the 1968-69 only idler pulley (68-69 bearing sku: 10827). The center portion of the pulley, where this bearing would press into, has an inside diameter measurement of 1 9/16". On the smaller bearing pulley, this measurement is 1 3/8". Both versions of this...

Reproduction stud and nut assembly that the factory line workers used for locating the air conditioning pedestal bracket. Then backed up with a nut. Used on 289 / 302 / 351W / 390 / 428CJ pedestals from 1967 - 1973. Stud is threaded into the cylinder head for easy installation of the cast iron pedestal bracket.*Note - Excludes 351C and 429CJ.

Air conditioning bearing replacement service. Send your flat bearing style, fixed or adjustable A/C pulley and we will exchange it or rebuild your exact pulley with a new flat bearing. Either large or small flat bearings, same price.  Dust caps hand fitted, for seamless installation. No extra tool marks, other than the factory peening. Check photos.Ford casting #'s D0AA-8A617-B, D0AZ-8678-D, C8AZ-8678-B, C8AZ-8678-C, C8AZ-8678-A, D8OH-19W653-A, D0AZ-8678-D.*Note* All new bearings will...

Air conditioning belt tensioning pulley with new bearing. This adjustable bracket and pulley was used on all 1970-73 351 engines that came with A/C, as well as 1970 428CJ & 1971 429CJ. This part often has a casting number of D0AA-8A617-C1 but not always. This adjustable idler pulley is identified by having the large bearing pulley. Same as the C8AZ-8678-A adjustable idler pulley only with a small bearing pulley. We also offer a bearing replacement service to rebuild your adjustable idler...

Stud that the factory line workers used for locating the air conditioning pedestal bracket. Then backed up with a nut. Used on 351C / 429CJ pedestals from 1970 - 1973.*Note - Excludes 289 / 302 / 351W / 390 / 428CJ engines.

These heater control knobs are sold in a set of three and fit good and tight. It is often little details like this that separate 1st and 2nd place when judged at car shows. Replaces Ford Part #: C9ZZ-18519-A.