All Available Parts - 1973 Mercury Cougar

Reproduction Firewall Insulation Pad Clip Kit for the 1967 - 1973 Mercury Cougar / Ford Mustang

Reproduction thin firewall insulation pad with clips for the Mercury Cougar or Ford Mustang. This unit will fit both the A/C and non A/C Cougar or Mustang.

Grade "B" part that will have only one of the four mounting tabs broken or cracked. Select a color and we will attempt to accommodate you.

Grade 'A' part that will have none of the four mounting tabs broken or cracked. Enter your preferred color in the order notes at checkout and we will attempt to accommodate you.

Replacement throttle pedal spring for your 71 - 73 Cougar or Mustang. Easy to replace, keeps correct tension on your gas pedal.

Screw for attaching steering column plate to floor board. Usually 4 are needed and go through the carpet and into the toe board. Correct finish and style of AMK bolt. Length 1 3/16"#14 Threads

Used driver side interior kick panel for any 1971-73 Mercury Cougar. Ford calls this item a "Panel - Cowl Trim". These came in a variety of different colors, please indicate a desired color in the notes. Plan on painting the panel with a quality vinyl paint such as those made by SEM for a quality installation. These are used, and will likely show some scuffing from hard shoes.  Ford part number D1WB-6502344, D2WB-6502344, D3WB-6502344. ...

Used driver side interior kick panel for any 1971-73 Mercury Cougar. Ford calls this item a "Panel - Cowl Trim". These came in a variety of different colors, please indicate a desired color in the notes. Plan on painting the panel with a quality vinyl paint such as those made by SEM for a quality installation. These are used, and will likely show some scuffing from hard shoes.  Ford part numbers D1WB-6502345, D2WB-6502345, D3WB-6502345.

Used Oil pressure gauge, Amp meter gauge, housing assembly for all 1971-73 Mercury Cougar XR7. This is the two gauge pod found in the center of the dash panels. We only sell these as assemblies, lens sold separately. Ford part numbers found on this part are D1WF-10848 & D1WF-10894. Check out the video below on our new gauge tester: ...

Good used console clock surround bezel with no cracks, or peeling chrome. Engineering number on the backside reads D1ZB-15017-AA

Used metal dash support brace for all 1971-73 Mercury Cougar and Ford Mustangs. Fastens to the lower flange of the metal dash panel and attaches to the inner cowl, 10 inches long. Replaces Ford part numbers D1ZB-6504672-A.

Don't be fooled by knobs with similar part numbers, they have longer shafts and will not work as well on your Mercury Cougar or Ford Mustang application.Ford part # D1ZZ-18830-A, and Ford casting # D1ZA-18A932-AA.*TRIVIA* Did you know that Ford called the inner (balance / tone) radio knobs "discs?"

Finally, a reproduction radio knob set for your 1971-73 Mercury Cougar or Ford Mustang! These little units are very hard to find in NOS form or good used condition with flawless chrome. Most knobs are peeling bad enough to cut you if you are not being cautious. It's often little detail pieces like these that separate first and second place at car shows.Replaces Ford part #'s D1ZZ-18817-A for the outer (tuner / volume) knob, Ford casting # D1ZA-18822-AA for the outer (tuner / volume) knob....

This kit is similar to the original type mounted in every drivers side door. These OEM style Riv-Nuts will be a challenge to install unless you have the special tool. Almost every body shop will have this rivet gun type of tool but here are a couple of ways to tackle the installation without the correct tool. Hole size is 1/4". Replaces Ford Part #: C7AZ-17696. Check out our video below for more info on mirror installation: Still have riv-nut questions? Here are riv-nut answers! ...

New mirror glass, for the passenger side on practically any 1969-73 Ford with painted sport mirrors. This is the convex style of mirror, think "Objects in mirror are closer than they appear". Nice fit, exact shape of originals. Dimensions: 4 3/8 x 2 7/8 Do you have questions about installing a passenger side mirror or using Riv-Nuts? Have more questions about installing a passenger side mirror or using Riv-Nuts? Got a mirror lens that flops around in your Sport Mirror every time you hit a tiny...

Pair of reproduction brackets and rods for the sun visors in the Mercury Cougar or Ford Mustang. *NOTE* These units will also work for the 1971-73 Ford Mustang fastback (sport roof).

This knurled nut is located under the front slides in each corner (1 per side, 2 per car) and is used to adjust the height of the sun roof panel.

Curved aluminum cable guide as seen on page 13 of the sun roof manual. Golde part number 100 413 682

Curved aluminum cable guide as seen on page 13 of the sun roof manual. Golde part number 100 413 681

Front guide that measures 10 5/8" long held in place by four screws. The driver side has no markings but the passenger side is stamped with an R and the inner 2 screw holes are in a different place than the driver.

Front guide that measures 10 5/8" long held in place by four screws. The driver side has no markings but the passenger side is stamped with an R and the inner 2 screw holes are in a different place than the passenger.

Guide that measures 10 5/8" long held in place by the outer trim that has four screws. Driver and Passenger are interchangeable.

This part mates to and is held down by Golde #100 413 682. The Golde part number for the smaller, lower elbow guide is 100 413 663

This part mates to and is held down by Golde #100 413 681. The Golde part number for the smaller, lower elbow guide is 100 413 664

This strip has a series of five retaining clips that hold the headlining panel to the roof panels as seen on page 14 of the sun roof manual.This is for the 1971-73 Mercury Cougar with factory sunroof. Sunroof measurements are roughly 19-1/2 x 39 inches. This panel is 32-1/4 inches long with 5 clips as shown.

Reproduction wrench or crank, for manually closing the factory installed sunroof installed on any 1967-73 Mercury Cougar. Sunroofs, technically moonroofs, were originally installed by ASC or American Sunroof Corporation. Hertz 1968 XR7-G cars all came with factory sunroofs, as did the Hertz rental 1969-70 Cougar Eliminators. ASC also installed sunroofs in Ford Thunderbird, Lincoln MK III.ASC used Golde mechanical parts from Germany. Golde was a manufacturer of sliding canvas and metal roofs on...

This strip has a series of seven retaining clips that hold the headlining panel to the roof panels as seen on page 14 of the sun roof manual.

This part is located in the right front corner of the panel and has to be rotated inward to remove it from the guide rail so the panel cannot be removed. Imprinted on the plastic portion of the part is a Golde part number 100 414 645. Ford part number C8WY-65502L08-A

12-point bolt for attaching the steering column coupler to the steering box. Works for all 1967-73 Mercury Cougars and most other Fords, Mercury, and Lincolns. One bolt used for fixed columns, two bolts used on tilt steering columns. Sold individually.

Reproduction insulator for the lower portion of the steering column found on all 1969-73 Mercury Cougar or Ford Mustangs. Unique slide in plastic bushing or insulator, which slides into the bottom tube of both fixed and tilt columns. Most originals are broken or missing. Two sizes of insulators, please verify year and diameter.1968 tube measures 1 3/8"1969 - 1973 tube measures 1 5/8"*NOTE* WCCC services all FoMoCo tilt and tilt-tilt away steering columns 1967-1979. Our shop rate for this...

Used Release Spring for the 1967 - 1973 Mercury Cougar / 1967 - 1973 Ford Mustang 

Used Spring Sleeve Cap for the 1967 - 1973 Mercury Cougar / 1967 - 1973 Ford Mustang 

Power window door harness from a 1973 Mercury Cougar. This passenger side door harness has the power window plug, door ajar plug, and stereo speaker plug. Factory harness, the extra plugs were not used if you had a standard model or AM radio. Tested and inspected and ready to install. Does not include any of the other power window harness segments, i.e. driver side door, rear windows, or under hood segments. Switches also not included. Does not fit 1972 or earlier cars, 1973 was a change over...

When your lights are sequencing too rapidly, causing the outer light to not fully illuminate, your original unit is most likely the culprit. This solid state unit replaces the small red (69-70) or green (71-73) flasher found under the dash, next to the radio. Replaces Ford part # D0WY-13350-A. *NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is the designer of all of our...

Used sequential unit (found in trunk) relay for all 1970-73 Mercury Cougar, 4 total per car. Additionally this relay was used as a horn relay for 1965 Ford Mustang with generators; 1966 Lincoln Continental relay for moveable steering columns; 1969 and later Ford and Mercury full sized with speed control relay and power back window relay (on station wagons). Ford Engineering # C4AZ-13853-A. *NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most...

New emergency flasher can for all 1969-73 Mercury Cougars. Not to be confused with the turn signal flasher canister, those are rated differently. 

When your lights are sequencing too rapidly, causing the outer light to not fully illuminate, your original unit is most likely the culprit. This solid state unit replaces the small red (69-70) or green (71-73) flasher found under the dash, next to the radio. NOTE* Some vehicles have the wiring reversed, you can get though this problem by using spades and hooking up to the contacts of the flasher backwards.  This is the updated flasher unit for use with the updated sequential unit and...

These clever kits allow you to replace the broken cam without having to swap the whole assembly. Mounting hardware is included. Works on 67-72 fixed columns and 67-73 tilt columns. Replaces Ford Part # C7SZ-13318-B and D0AZ-13318-A. Watch Install Video

Our turn signal switches are made by the original supplier to Ford from the original tooling. If you have replaced your sequential unit in the trunk with one of our new solid state sequential units and are still having problems then the turn signal switch is most likely the culprit as the only other part to the system is the wiring harness itself. Often when your brake lights are not working the turn signal switch is the culprit as the brake lights feed through the turn signal switch. This...

Our turn signal switches are made by the original supplier to Ford from the original tooling. If you have replaced your sequential unit in the trunk with one of our new solid state sequential units and are still having problems then the turn signal switch is most likely the culprit as the only other part to the system is the wiring harness itself. Often when your brake lights are not working the turn signal switch is the culprit as the brake lights feed through the turn signal switch. This...

Unique shouldered screw that keeps your switch in perfect alignment, using incorrect screws will damage the switch.Fixed columns require 3 screws. Tilt columns require 2 screws.  *NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is the designer of all of our solid state sequential systems. There is no question he cannot answer! Here is a link to a great source of...

Reproduction master power window switch for 1973 Cougars and Mustangs. Five switch assembly - driver / passenger front and rear windows, and a master lock out switch. This reproduction is identical with the exception of the smoother edged switches. Fits 1973 Mercury Cougar and Ford Mustang.

This used power window relay mounts to the front inner apron on the passenger side just behind the starter solenoid.This relay also used for 1969-73 power convertible tops, and 1971-73 power seat.Replaces Ford part #: C8AB-14677-A.

Power lead from starter solenoid to circuit breaker for any of the following: power windows, convertible top, automatic seat back release, headed back light or rear defog (1971-73), or power seat.Replaces Ford Part #: C9WB-14678-B

This is a good used main power window wiring harness that passes through the firewall, travels along the passenger side engine compartment and mates the the rectangular power window relay. Fits 1971-73 Mercury Cougars with factory power windows. Also powers the convertible top switch only when power windows are included. This is a Grade A harness that has been tested and inspected. This harness will look and function correctly. We also sell a Grade B harness that will have at least one...

Reproduction drum brake pedal pad for the Mercury Cougar or Ford Mustang equipped with an automatic transmission. The 1967 version of this piece is narrower than this 1968-73 piece.Replaces Ford part # C6OZ-2457-A.

These reproduction brake and clutch pedal bushings are made from high strength plastic that is wear resistant. Two are required for automatic cars, four for manual transmission cars. Sold as a pair. Replaces Ford part # B7AZ-2471-A.

Features the proper cover and original logos. I A S F stamped on cover.Replaces Ford Part #: D3AF-10316-A. These new voltage regulators are improved and more reliable than the units we've sold previously.

These new voltage regulators are improved and more reliable than the units we've sold previously. Replaces Ford part number D3TF-10316-AA

Courtesy light door jamb switch with automatic seat back release option. Three pin switch not for use without seat back release. Additionally, this three prong switch was used on most 1970-76 Full and mid sized Ford, Mercury, and Lincoln. Some with or without the seat back release option.Replaces Ford Part #: D1AZ-13713-E and D0OZ-13713-A. This is a new reproduction part not Motorcraft.

OEM Motorcraft 2 prong door jamb switch 3/4 inch door jamb mounting holes. Passenger side switch courtesy light switch, for use on 1971-73 Mercury Cougar and Ford Mustang without automatic seat back release option. Replaces Ford Part #: C8OZ-13713-A.

This quality reproduction is made from the original tooling and should give you the same reliability of the original that lasted 30-40 years. Replaces Ford part number C0TZ-13A024-A

Reproduction headlight switch knob for the 71 - 73 Cougar.

This plastic plate / bracket is installed between dimmer switch and the floor of your 67 - 73 Cougar to provide a bit or protection for the wiring.

NOS new old stock headlight dimmer switch. This is a Motorcraft service replacement switch.  Replaces Ford part number C0TZ-13A024-A

Tested and inspected neutral safety switch for the FMX transmission installed after 1/5/1972 through 1973 Mercury Cougar and Ford Mustangs. Look for a transmission code of X on your door data plate. If your car has a code U, your original transmission was an C6 and uses a different neutral safety switch. This version is identified by having 2 plugs.Replaces Ford Part #: D2ZZ-7A247-B, SW 903-B.

Tested and inspected neutral safety switch for the C-6 transmission installed in mid 1972-73 Mercury Cougar and Ford Mustangs. Found on cars after build date 12/15/1971. This transmission neutral safety switch has two plugs.Look for a transmission code of U on your door data plate. If your car has a code X, your original transmission was an FMX and uses a different neutral safety switch.Replaces Ford Part #: D2ZP-7A247-AA, BA or D2ZZ-7A247-C, SW 1148.Fits:1972 Mercury Cougar1973 Mercury...

The correct switch with the correct Connectors and color coded wires. Replaces Ford Part #: D2ZZ-7A247-A, SW-906-A.

Consolette wiring harness, bridges the main under dash wiring harness and the ashtray light pigtail. Not for full length consoles. Ford part # D1WB-15A056-AB.

Wiring pigtail with bulb socket and shroud for 1971-73 Mercury Cougar with small consolette. Two different versions of this light, plastic and metal bulb socket. Inspected, tested and ready to install. Bulb not included. Ford part # D1WB-13A726-AB.

D3WB-13A769-BA Right side door wiring harness as found on 1973 Cougars with door courtesy lights and factory installed stereo. Wiring harness for courtesy door lights and factory door speakers only. Master part number D3WY-13A769-A. This is a grade "B" good used harness, expect minor splices, damaged rubber boots or other easily repairable minor damage. *Note - Excludes 1973 doors with power windows.

D3WB-13A769-AA Left side door wiring harness as found on 1973 Cougars with door courtesy lights and factory installed stereo. Wiring harness for courtesy door lights and factory door speakers only. Master part number D3WY-13A769-B. This is a grade "B" good used harness, expect minor splices, damaged rubber boots or other easily repairable minor damage. *Note - Excludes 1973 doors with power windows.

Passenger side door wiring harness as found on most late 1972 - 1973 Cougar XR7. Used on all XR7's unless it had the power window option. Harness for ajar and door stereo speakers, even if it was an AM radio car. This is a grade "A" premium grade harness that is not sun damaged, spliced or damaged in anyway. Identified by having a blue plug for the ajar wire. Ford part number D1WB-13A769-AE or D1WY-13A769-F.* Note - Not for cars with power windows.* Note - Not for 1971 or early 1972 cars,...

Small retaining ring that secures the engine gauge feed wiring harness to the driver side valve cover. Two were used per engine. We found this part in the 1971-72 Mustang Electrical Assembly Manual. To be used with original wiring harnesses, the reproduction engine gauge feed harness does not have the clips to attach to this retainer.Ford part number D2AB-14A163-MA.

D1AZ-14018-A Door ajar switch found on 1971-73 Mercury Cougar XR7's and part of the Convenience Group package found optionally on standard Cougars. The visual check panel or "convenience panel" option included the 'door ajar' light. Switch is the same for both doors. This switch was also used on 1972 Lincoln MK IV, and 1972 Ford Thunderbird.Fits 71 Cougar and XR7Fits 72 Cougar and XR7Fits 73 Cougar and XR7Fits 72 Lincoln MK IVFits 72 Ford Thunderbird ...

Used jumper wire for the door ajar switch as found on 1971-73 Mercury XR7's. One end has a spade connector for the ajar switch, the other end is a bullet connector to the main door harness. Fits both driver and passenger side, about 41 inches in length.Replaces Ford part number D1WB-10C865.

OEM Motorcraft 2 prong door jamb switch 3/4 inch door jamb mounting holes. Various applications, some for passenger side, some both sides. Replaces Ford Part #: C8OZ-13713-A.

This plastic socket is very brittle and almost always breaks when installing a new door jamb switches. Does not fit cars with Warning Group with door ajar option. Simply install by carefully breaking the old brittle plastic socket apart with pliers to free up the wire leads and plug wire leads into the new socket.

3/4" wide and 60' long. This tape resembles the tape you would find on bicycle handle bars or a hockey stick but is in fact different. The taillight harness uses this type of tape as well as portions of the under dash harness. Not used in modern applications and getting rather hard to find these days.NOTE: This is FRICTION tape not adhesive tape. It is coated with rubber and relies on friction with itself to wrap wires. It does not stick to the wires. This was one of the first types of...

Wiring pigtail for the low fuel sending units on 1973 Mercury Cougar XR7 and standard models with low fuel warning light, cut from a taillight wiring harness. The wiring is all integrated in 1973, unlike 1971-72 which has a separate harness for the fuel sending unit. The Safety Convenience Package included a low fuel warning light. This pigtail has three wires which attaches to the three prongs on the D1WF-9275-AC low fuel sending units. Ford part number is D3WB-14406-B or D3WY-14406-B. *Note...

Used Standard Grade A Taillight Wiring Harness for the 1973 Mercury Cougar 

Used Standard Grade B Taillight Wiring Harness for the 1973 Mercury Cougar 

Used XR7 Taillight Wiring Harness for the 1973 Mercury Cougar 

Used grade "A" under dash wiring harness and fuse panel / block for the Mercury Cougar standard and standard convertible. This very clean uncut harness is not corroded on the connections or brittle from heat and is tested and ready to install.*NOTE* If you send us your old used under dash harness, you will receive an in store credit of up to $100. Also keep in mind that we buy original under dash harnesses. We are interested in all under dash harnesses, but are primarily interested in the XR7...

Used under dash harness repair plug and pigtail for the light switch harness for the Mercury Cougar Standard and XR7. This is part of the 14401 main under dash wiring harness.*NOTE* The individual wires can be removed from the block and other wires can be inserted if your car has different options.

Alternator spacer bracket for all 351 engines. 1970-73 Mercury Cougar and Ford Mustang among others such as Torino, Cyclone, Galaxie, LTD, etc. Aluminum material, 2-1/4 inches long, with a 7/16" hole. Sometimes solid and sometimes open along the side. Ford part number D0OZ-10A370-A.

Used alternator mounting bracket for any 1970-73 Mercury Cougar, Ford or Ford Mustang with 302, 351W, or 351C engines. Replaces Ford part number D0OE-10156-A.

Used alternator adjusting arm for any 1970-73 Mercury Cougar, Ford Mustang, or generally Ford anything with 302, 351, or Boss 302 engines. This can be used on 1973 cars, Ford did switch to a different alternator bracket that tightened the alternator from the back sometime in 1973. Replaces Ford part number D0OE-10145-A, listed in the Motorcraft catalog as GY-938Also fits:Comet Montego

Ford started using this alternator adjusting bracket sometime in 1973. It mounts to the rear of the alternator. Fits any 1973 Mercury Cougar and Ford Mustang and likely many other Ford cars with 351 engines. It works with the 1970-73 front mounting bracket. Replaces Ford part number D3AE-10145-C.

Original engine frame mount brackets for all 1971 to 1973 Cougar *convertibles regardless of engine and all 1971 Cougar 429 Cobra Jets. Includes one each: D1ZZ-6028-A & D1ZZ-6029-A engine frame brackets. Visually, there are also a version where there is a double set of holes on top. *Excludes non-convertibles with 351 cubic inch engines.

Factory original part for all 1971 - 1973 Cougar *convertibles. Also correct for 1971 429CJ all body styles. Right hand bracket. Ford part number D1ZZ-6028-A.Does not come with hardware. May have a single or pair of holes on the flat surface. We see them both ways.*Excludes non-convertible models.

Factory original part for all 1971 - 1973 Cougar *convertibles. Also correct for 1971 429CJ all body styles. Left hand bracket. Ford part number D1ZZ-6029-A. May have a single or pair of holes on the flat surface. We see them both ways.*Excludes non-convertible models.

Sold individually # 56354-S

Used standard grade "B" main under hood wiring harness located in the engine compartment. This harness has plugs for the head lights, voltage regulator, starter solenoid, windshield washer pump, and horns. All electrical harnesses are inspected, professionally repaired, tested, and ready to install. Grade "B" harnesses may have one or two repairs as where grade "A" harnesses will be rare uncut beauties. 1973 Mercury Cougar Standard models only with AMP warning light. Not compatible with XR7...

Used grade "B" under dash wiring harness and fuse panel / block for the Mercury Cougar standard and standard convertible. This harness may have one or two professional repairs, it is tested and ready to install.*NOTE* If you send us your old used under dash harness, you will receive an in store credit of up to $100. Also keep in mind that we buy original under dash harnesses. We are interested in all under dash harnesses, but are primarily interested in the XR7 harness.Ford part # D3WY-14401. ...

Engine mount for all 1973 V-8 engines in 1973 Mercury Cougar and Ford Mustang coupe body styles only. 1973 only, and these only work with hardtop or coupe engine frame stands. We occasionally have these in good used condition, normally only one side is broken or worn.  In the long run we recommend converting to 1971-72 coupe engine stands and mounts. This requires replacing BOTH the 1973 coupe engine frame stands as well as the engine mounts with the 1971 - 1972 coupe version.Sold...

Engine mount bolt kit for installing engine or motor mounts to the frame stands. 1971-73 Mercury Cougar or Ford Mustang V-8. Two bolts and two nuts. Quality AMK part F-467.

D0AZ-3A732-C Stamped steel bracket for mounting the power steering pump. Ford called this bracket the 'power steering pump adjusting bracket'. For any factory air conditioned or non-air conditioned 1971 - 1973 Cougar or Mustang with 351 engines, additionally used on Mustangs with the F code 302 V8 engines.

Used power steering oil cooler for many 1971-73 Ford, Lincoln and Mercury cars with air conditioning. Specifically these came from 1971-73 Mercury Cougar or Ford Mustangs with factory installed air conditioning and power steering. This unit mounts to the top of the A/C compressor. This installs inline with the low pressure return hose.  Manufactured by the Blissfield Company and has a Ford stamped number of D1AA-3D746-AB. The Ford engineering number is D1AZ-3D746-D. 

Sold as a pair. One long and one short bracket. Fits 1971-73 Mercury Cougar and Ford Mustangs that have original style radiators.  Mounting bolts not included. Replaces Ford part number D0OB-8B359 RH, and D0AB-8K007 LH. Check out our video on Radiator and Fan upgrades below: ...

C6AE-E Multiple applications over the years. 1. Later 1967 production cooling fan, generally used after 11/14/1966 on most 289 engine applications. 2. 1968 302 without air conditioning. 3. Mid year (after 11/6/1968) 1969 351 without air conditioning. 4. 1969 Early Boss 302 before 4/14/1969. 5. 1971 Cougar with 351 engine, without air conditioning. 6. **1973 Cougar 351-2V without air conditioning prior to 2/19/1973. Fan description - 4 blades and 17-1/2 inches in diameter. Ford master part...

D2OE-AB Applications: 1. 1972 Cougar with H code 351-2V engines - without air conditioning. 2. 1973 Cougar with H code 351-2V engine after 2/19/1973 - without air conditioning. May also be marked D2OE-AA. Fan description - 4 blades and 18-1/2 inches in diameter. Ford master part number D2OZ-8600-A. Check out this interesting video where they test the efficiency of factory style and aftermarket fans. Spoiler alert: the clutch fans are the most efficient! ...

D2OE-AA Applications: 1. 1972 Cougar with H code 351-2V engines - without air conditioning. 2. 1973 Cougar with H code 351-2V engine after 2/19/1973 - without air conditioning. May also be marked D2OE-AB. Fan description - 4 blades and 18-1/2 inches in diameter. Ford master part number D2OZ-8600-A. Check out this interesting video where they test the efficiency of factory style and aftermarket fans. Spoiler alert: the clutch fans are the most efficient! ...

D3ZE-8146-AB Original used fan shroud with a 1973 casting number. Should be for all V-8 engines with air conditioning. Good used, this exact 1973 shroud is not reproduced. For some helpful tips on upgrading your Cougar (or Mustang) cooling system, check out our video:

This is an excellent reproduction made from the original Ford tooling and features the original Ford logo. This is correct for all the cross flow radiators used in 1971 - 1973 except the 1971 429CJ. Opening measures about 20-1/8" in diameter. Replaces Ford part # D1ZZ-8146. For some helpful tips on upgrading your Cougar (or Mustang) cooling system, check out our video: ...

Fan shroud hardware kit for the 302 or 351 on the 1971, 1972 or 1973 Cougar and Mustang.

These concours quality Zinc caps are made in America and bear all the original markings. O.E.M. details include original letter style, "S.M.C.O." and "Autolite". Pound rating is stamped on cap.

These concours quality Chrome caps are made in America and bear all the original markings. O.E.M. details include original letter style, "S.M.C.O." and "Autolite". Pound rating is stamped on cap.

These are O.E.M. replacements and will not fit most after market radiators.

Keeps the corrosive agent in your coolant from destroying vital engine components