All Available Parts - 1969 Mercury Cougar

PCV tube for the Mercury Cougar, Ford Mustang GT500KR and Torino with the 428 CobraJet and Super CobraJet for 1968-69 and C8OZ-9424-C factory iron intake manifold. The main difference between the 390 tube and the 428 tube is the center fitting angle. The 428 tube has a less pronounced angle, this is due to the taller 428CJ intake manifold. A less pronounced angle fits more closely to the passenger side valve cover. Replaces Ford Part #: C8OZ-6758-B.

This fitting screws into intake manifold, has 1/2" nipple for PCV hose, 3/16" vacuum port nipple and threaded hole for smaller accessory fitting. Painted Ford Corporate blue from the factory.

This tachometer was only used on the 1969 BOSS 302 Eliminator but occasionally found its way into other models. This is a tested, working original part. 69 differs from 70 only in the indicator lights at the bottom.Check out the video below on our new gauge tester: ...

Used steel lower dash panel for all 1969 Mercury Cougar and Ford Mustang without factory air conditioning, this panel does not have the round holes in the outer section. This is not a reproduced part, only the 'with' A/C panel is reproduced. This is a bolt in dash section, ships bare, no brackets included. The easiest way to identify a 69 lower dash from a 70 is that the square cutout for the steering column measures 6 3/8" wide on the 69 and 7" wide on the 1970. Grade A used, no pitting, no...

Used steel lower dash panel for all 1969 Mercury Cougar and Ford Mustang without factory air conditioning, this panel does not have the round holes in the outer section. This is not a reproduced part, only the 'with' A/C panel is reproduced. This is a bolt in dash section, ships bare, no brackets included. The easiest way to identify a 69 lower dash from a 70 is that the square cutout for the steering column measures 6 3/8" wide on the 69 and 7" wide on the 1970. Grade B used, may have...

Used steel lower dash panel for all 1969 Mercury Cougar and Ford Mustang with factory air conditioning. This is a bolt in dash section, ships bare, no brackets included. The easiest way to identify a 69 lower dash from a 70 is that the square cutout for the steering column measures 6 3/8" wide on the 69 and 7" wide on the 1970. Grade B used some pitting and or  extra holes. Replaces Ford part number C9ZZ-6504320-D.

If you look close at our used set I do not think you could tell the difference, look at the back side in comparison to used and you will see a noticeable difference. *NOTE* The fifth part slips into the backside of the inner knob on the passenger side and acts as a spacer for Cougars or Mustangs without the rear fader option. The radios that would not utilize the white plastic spacer would be 1967 radios with factory rear speakers, 68-70 AM radios with rear speakers and 68-70 AM-FM radios. ...

These plastic vertical trim parts mount under the dash pad, to the right and left of the radio. Available in black only, sold as a pair and "almost" as nice as our originals but you will notice the grain (texture) is less defined on the reproductions. We have perfect used in an array of colors. *Customer Feedback* "I have checked out this website several times and it is a great source for information and these guys know what they are talking about. They are friendly and willing to help with...

Nice clean set of four used radio knobs for your 69-70 Mustang or Cougar. No peeling or cracks. The inset picture shows the used next to the new from the backside. The reproductions are shown on the right. Whereas the repros are nice, the originals are still superior. The radios that would not utilize the white plastic spacer would be 1967 radios with factory rear speakers, 68-70 AM radios with rear speakers and 68-70 AM-FM radios. White plastic reproduction spacers available here. The white...

New mirror glass, for the passenger side on practically any 1969-73 Ford with painted sport mirrors. This is the convex style of mirror, think "Objects in mirror are closer than they appear". Nice fit, exact shape of originals. Dimensions: 4 3/8 x 2 7/8 Do you have questions about installing a passenger side mirror or using Riv-Nuts? Have more questions about installing a passenger side mirror or using Riv-Nuts? Got a mirror lens that flops around in your Sport Mirror every time you hit a tiny...

1969 Driver side Sport mirror with rechromed Cougar base. Mirrors disassembled, and reassembled with our rechromed OEM Cougar mirror base. Obviously will need to be repainted, but will have a fresh chromed mirror base like on the 1969 XR7's. Comes as shown with used glass and working remote. Door panel bezels, door gasket, new glass, and nuts available separately. 

For those wanting to make their own "custom" package tray this will assist you in getting the correct dimensions the first time. This template is traced from a reproduction packege tray onto a piece of butcher paper.

If losing weight in your 1969 - 1970 Coupe is what you are after then this would be a good part for you as it weighs less than one pound and the original weighs approximately five pounds. The original is made of the same material as the sound deadener found under the carpet and we rarely get good examples in stock.

Unfortunately this is yet another incorrect reproduction made by someone who has never even sat in a Cougar. No embossment, no courtesy light holes if you have xr7 and no foil backing. These are sold as a pair. There are two different sources that will hand make these to show quality specs, you can locate them at www.mercurycougar.net   Sorry, we never get good used units in these days. *NOTE*  This would be a good time to purchase trunk filler boards and package tray if you need...

Wow! Almost nothing is 100% correct about these rear package trays... No, your monitor is not out of adjustment, these colors are truly wrong except for the black. A couple of the colors are "close" to original but most will have to be repainted if you are concerned about correctness. The mesh is much lighter weight than the original and the speaker holes are not exact but the fit is good and overall this is a durable attractive piece. NOTE: Package Tray has a perforation you have to bend on...

Wow! Almost nothing is 100% correct about these rear package trays... No, your monitor is not out of adjustment, these colors are truly wrong except for the black. A couple of the colors are "close" to original but most will have to be repainted if you are concerned about correctness. The mesh is much lighter weight than the original and the speaker holes are not exact but the fit is good and overall this is a durable attractive piece. If you buy the insulation pad that lies beneath this panel...

Wow! Almost nothing is 100% correct about these rear package trays... No, your monitor is not out of adjustment, these colors are truly wrong except for the black. A couple of the colors are "close" to original but most will have to be repainted if you are concerned about correctness. The mesh is much lighter weight than the original and the speaker holes are not exact but the fit is good and overall this is a durable attractive piece. NOTE: Package Tray has a perforation you have to bend on...

Wow! Almost nothing is 100% correct about these rear package trays... No, your monitor is not out of adjustment, these colors are truly wrong except for the black. A couple of the colors are "close" to original but most will have to be repainted if you are concerned about correctness. The mesh is much lighter weight than the original and the speaker holes are not exact but the fit is good and overall this is a durable attractive piece. If you buy the insulation pad that lies beneath this panel...

Wow! Almost nothing is 100% correct about these rear package trays... No, your monitor is not out of adjustment, these colors are truly wrong except for the black. A couple of the colors are "close" to original but most will have to be repainted if you are concerned about correctness. The mesh is much lighter weight than the original and the speaker holes are not exact but the fit is good and overall this is a durable attractive piece. NOTE: Package Tray has a perforation you have to bend on...

These fasteners were used to keep your package tray in place. In 1969 - 1970 the two clips were held in place with screws. Sold individually. We have seen various tech type screw with both large and small heads on them for fastening these clips. Same clip as was used in 1967-68, but without the push clip. We try to supply the screw, but you would likely want to get fresh ones, they are nothing special.Replaces Ford part number C4AB-6246698-A.

Wow! Almost nothing is 100% correct about these rear package trays... No, your monitor is not out of adjustment, these colors are truly wrong except for the black. A couple of the colors are "close" to original but most will have to be repainted if you are concerned about correctness. The mesh is much lighter weight than the original and the speaker holes are not exact but the fit is good and overall this is a durable attractive piece. NOTE: Package Tray has a perforation you have to bend on...

Wow! Almost nothing is 100% correct about these rear package trays... No, your monitor is not out of adjustment, these colors are truly wrong except for the black. A couple of the colors are "close" to original but most will have to be repainted if you are concerned about correctness. The mesh is much lighter weight than the original and the speaker holes are not exact but the fit is good and overall this is a durable attractive piece. NOTE: Package Tray has a perforation you have to bend on...

This white plastic spacer fits into the back of the right hand inner knob on cars without factory fader or balance. If your inner knob is loose and will not align, you will want to see if this part is in place. 1968-70 AM-FM radios would not utilize this part because they have a balance feature. 1967 AM-FM radios would use this part as they did not have a balance feature. Called a "Sleeve" 1969-70 Cougar and Mustang AM radios use this sleeve. Also found on various 1970-76 Ford and Mercury cars...

For most applications, we highly suggest you upgrade to our solid state version of this unit.  Ford part # C9WY-13350-A, Ford service replacement part # D0WY-13350-A. *NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is the designer of all of our solid state sequential systems. There is no question he cannot answer! Here is a link to a great source of information on...

This kit is similar to the original type mounted in every drivers side door. These OEM style Riv-Nuts will be a challenge to install unless you have the special tool. Almost every body shop will have this rivet gun type of tool but here are a couple of ways to tackle the installation without the correct tool. Hole size is 1/4". Replaces Ford Part #: C7AZ-17696. Check out our video below for more info on mirror installation: Still have riv-nut questions? Here are riv-nut answers! ...

Reproduction wrench or crank, for manually closing the factory installed sunroof installed on any 1967-73 Mercury Cougar. Sunroofs, technically moonroofs, were originally installed by ASC or American Sunroof Corporation. Hertz 1968 XR7-G cars all came with factory sunroofs, as did the Hertz rental 1969-70 Cougar Eliminators. ASC also installed sunroofs in Ford Thunderbird, Lincoln MK III.ASC used Golde mechanical parts from Germany. Golde was a manufacturer of sliding canvas and metal roofs on...

This strip has a series of seven retaining clips that hold the headlining panel to the roof panels as seen on page 14 of the sun roof manual.

This part is located in the right front corner of the panel and has to be rotated inward to remove it from the guide rail so the panel cannot be removed. Imprinted on the plastic portion of the part is a Golde part number 100 414 645. Ford part number C8WY-65502L08-A

This knurled nut is located under the front slides in each corner (1 per side, 2 per car) and is used to adjust the height of the sun roof panel.

Curved aluminum cable guide as seen on page 13 of the sun roof manual. Golde part number 100 413 682

Curved aluminum cable guide as seen on page 13 of the sun roof manual. Golde part number 100 413 681

Front guide that measures 10 5/8" long held in place by four screws. The driver side has no markings but the passenger side is stamped with an R and the inner 2 screw holes are in a different place than the driver.

Front guide that measures 10 5/8" long held in place by four screws. The driver side has no markings but the passenger side is stamped with an R and the inner 2 screw holes are in a different place than the passenger.

Guide that measures 10 5/8" long held in place by the outer trim that has four screws. Driver and Passenger are interchangeable.

This part mates to and is held down by Golde #100 413 682. The Golde part number for the smaller, lower elbow guide is 100 413 663

This part mates to and is held down by Golde #100 413 681. The Golde part number for the smaller, lower elbow guide is 100 413 664

This strip has a series of five retaining clips that hold the headlining panel to the roof panels as seen on page 14 of the sun roof manual.This is for the 1971-73 Mercury Cougar with factory sunroof. Sunroof measurements are roughly 19-1/2 x 39 inches. This panel is 32-1/4 inches long with 5 clips as shown.

Emergency flasher switch bezel for the side of fixed steering columns (non-tilt). For all years 1967 1968 1969. Paint to match your interior. Compared to the reproduction version of this bezel, there is a difference. "Emergency Flasher" lettering is much heavier on the originals, plus they came color matched to the steering columns. We can often times supply your desired color, please include color needs in the comments section. Ford part number C9OZ-15C580-A.

Used upper steering column cover for the Mercury Cougar or Ford Mustang equipped with the tilt/tilt away steering column. This unit comes naked with no attaching parts or fasteners.*NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year. WCCC no longer has an in-house service for tilt and tilt-tilt away steering columns 1967-1979. After 2...

Used upper knuckle assembly for the tilt / tilt away column for the Mercury Cougar or Ford Mustang equipped with a tilt / tilt away steering column. There is an active thread on the Classic Cougar Community Forum discussing tilt columns and trouble shooting. *NOTE* We'll give you UP TO $100 cash back for your old knuckle assembly. The amount you will get back will depend upon how many usable parts that can be salvaged from your old unit. *NOTE* For tilt column service, you can contact Tony...

This is my most favorite Cougar - Mustang - Shelby option of all time! In fact as a rather tall person, that is not as slim as I once was, I do not really enjoy driving a Pony car that does not have this option anymore. This column does not only manually adjust up and down with the depression of the turn signal wand, it also releases and swings up and towards the passenger side of the car each time the ignition is turned off and the door is opened. To start the car you must close the door and...

Used locking lever for the tilt / tilt away equipped Mercury Cougar or Ford Mustang. Two required per car. Here is an active thread on the Classic Cougar Community Forum discussing tilt columns and trouble shooting. *NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year. ...

1967 Cougar Owners: To view our exploded view interactive diagram of the tilt steering column parts, click here. Used to mount the vacuum actuator to the column in 1967 and the actuator to the bracket on 68-69. Also used to mount the steering column relay and vacuum release valve in 1968-69.*NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last...

Used cap for the index lever tension spring for the Mercury Cougar or Ford Mustang equipped with the tilt/tilt away steering column. Two required per car.*NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year.

Used retaining clip for the adjustment bar in the tilt / tilt away steering column in the Mercury Cougar or Ford Mustang. Two required per car, used to hold the tilt position adjustment bar in place.  * While not technically correct, this also will work for 1970 - 1974 Cougar/ Mustang tilt columns. SOLD INDIVIDUALLY*NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our...

1967 Cougar Owners: To view our exploded view interactive diagram of the tilt steering column parts, click here. Used pin for the locking lever in the tilt / tilt away steering column found in the Mercury Cougar or Ford Mustang. Two are required in 1967-69, but only one is required for 1970 and up. Recommend changing to a up dated version of this pin with one that has circlips or snap rings (15-0156 for 1967 -69 or 15-0157 for 1970-1973) *NOTE* For tilt column service, you can contact Tony...

Used lower steering column bearing for the 67-73 Cougar or Mustang. The tilt columns take an upper and lower bearing, while the fixed column only takes an upper. The upper bearing can be found here. Outside diameter: 1.500"Inside diameter: 1.060" *NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year. ...

Used clip for the adjustment tension spring for the tilt / tilt away steering column found in the Mercury Cougar or Ford Mustang. One required per car. *NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year.

Keep in mind we can repair these for half or less of the price we charge to sell one outright. We can also install parts and or refurbish these columns. Ford part number C9ZZ-3E520-A *NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year. ...

Used tilt / tilt away steering column lock relay for the Mercury Cougar or Ford Mustang. Keep in mind we have a reproduction substitution for this part. This unit can be identified with the bend in the bracket compared to the 1967 relay which is straight. These relays are tested by our electrical department. Ford part # C8ZA-3E553-A. There is an active thread on the Classic Cougar Community Forum discussing tilt columns and trouble shooting.*NOTE* For tilt column service, you can contact...

Used release lever for the tilt / tilt away steering column equipped Mercury Cougar or Ford Mustang. This unit is sometimes also called a bale. *NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year.

Vacuum / electric tilt away solenoid for the 1969 Mercury Cougar and Ford Mustang. Original Ford part number C9ZZ-3D536-A. These vacuum tilt solenoids are tested and guaranteed to work. Bench testing the 1967-69 tilt away release solenoid: Verify that there is continuity between the two electrical spade connectors. No continuity means the the windings in solenoid windings are bad. This is a bad solenoid. Next, put vacuum to the lower port (10-17 inches of vacuum) any handheld or car vacuum...

Used spring cap that is used in the tilt / tilt away steering column found in the Mercury Cougar or Ford Mustang. One required per car. *NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year.

Used pivot cover for the tilt / tilt away steering column found in the Mercury Cougar or Ford Mustang. *NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year.

Don't try to straighten your rod if it looks like this. The contour seen here is correct. *NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year.

Used jumper wire used in the tilt / tilt away steering column found in the Mercury Cougar or Ford Mustang. *NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year.

1 3/8" hose that connects the vacuum motor to vacuum release valve. Often the white C9ZA-3D539-A and double white stripe imprint on this hose will be visible but not always. This hose measures 1 3/8" long.*NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year. ...

One year only design.*NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year.

Used jumper wire that connects the tilt-a-way door jamb and to the underdash harness.*NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year.

WCCC no longer has an in-house service for tilt and tilt-tilt away steering columns 1967-1979. After 2 years of working exclusively with Tony Augustine in MO, we can highly recommend him as one of the top most knowledgeable builders of these unique columns in the world.We now exclusively send all of the columns we sell as rebuilt to Tony for service.He can be reached at 816-210-4779 or 6t8cougarguy@gmail.com Make sure you tell him WCCC sent you! Don Rush, owner of West Coast Classic Cougar....

Used lower shaft used in the tilt / tilt away steering column found in the 1968-69 Mercury Cougar or Ford Mustang. This is the portion that mates with the upper shaft that bolts to the steering coupler. Overall length of this shaft is 15-11/16 inches long.*NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year. ...

Used tube insulator for the lower portion of the steering column found in 1969-72 Mercury Cougar or Ford Mustang. Because of the very fragile nature of this unit, stock is limited. Reproduction version is normally available, see related items. Ford part # C9AZ-3E629-A. *NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year. ...

12 Point bolt for attaching the steering column coupler to the steering box. All 1967-73 Mercury Cougar and most all other Ford, Mercury, and Lincolns. One bolt used for fixed columns, two bolts used on tilt steering columns.*NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year. ...

Three required per car, held in place by Allen head bolt, fits in the three slots at the top of the column tube.*NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year.Fits: 1968 Mercury Cougar1969 Mercury Cougar 1968 Ford Mustang1969 Ford Mustang ...

Emergency flasher switch bezel for the side of fixed steering columns (non-tilt). For all years 1967 1968 1969. Paint to match your interior. There is a slight difference between the original bezel and these reproductions. Original bezels have taller "Emergency Flasher" lettering, plus they came color matched to the steering columns. Functional reproduction item. Ford part number C9OZ-15C580-A.

Used steering column flange bumper for the Mercury Cougar or Ford Mustang equipped with the tilt / tilt away steering column. This little unit is made of plastic and Ford used it to keep the tilt / tilt away steering column's flanges in the knuckle assembly from breaking its self apart during actuation. Because of the forces generated in the tilt / tilt away column's actuation, your knuckle assembly will fail due to metal to metal contact if this piece is missing. Ford part # C7SZ-3D565C....

Used steering column tube retainer for the 67 - 69 Mercury Cougar or Ford Mustang equipped with the tilt / tilt away steering column. These little units help hold the steering column together and there are 3 required per column. Sold individually. This are not advisable in the 1970 and later cars. Ford part # C7SZ-3499-A. *NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our...

Used steering column tube and locking pawl spacer for the Mercury Cougar or Ford Mustang equipped with the tilt / tilt away steering column. This unit is used to align the inner steering column tube and align the locking pawl cable with the lower flange. Ford part # C9SZ-3C708-A.*NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year. ...

Used inner steering column tube for the tilt / tilt away for the Mercury Cougar or Ford Mustang. This unit fits within the outer steering column and is specific to 1969. Ford part # C9AZ-7212-F. *NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year. ...

Used tilt / tilt away steering column converted into a tilt only unit for the Mercury Cougar or Ford Mustang. All 1967-69 Cougars and Mustangs optioned with a tilt column also had the tilt-away (aka tilt-swing, tilt-fly or tilt-pop). There was never a tilt only option in 1967-69 Cougar or Mustang, no matter what you may have been told... That being said some of our customers prefer not to have the added expense or complexity involved with the swing-away function. This column has been fused at...

For use on fixed columns only. Attaches to the bottom side of the column to keep the wiring in place. Fits all 1968-69 Mercury Cougar, Ford Mustang, Ford Torino, Mercury Cyclone.*NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is the designer of all of our solid state sequential systems. There is no question he cannot answer! Here is a link to a great source of...

Here is a time and money saving package deal for the person restoring their 1969 Cougar. This package includes: Hood lip moulding Fender extension mouldings Deck lid moulding Drip rail mouldings Nine piece front and rear window trim Front and rear Award Winning Bumpers Keep in mind we will often give extra core value trade in for items we may be low on. Please call before sending extra parts for trade value. All parts are show quality. The bumpers are triple plated chrome, the aluminum has the...

Driver quality complete assembly with average chrome, emblem and cracked lens.

Restored stainless steel convertible top trim for the middle section of the exterior boot trim. This is a two piece set of trim, a right and left section, which slip fit together.  We only sell this item on an exchange basis only, you are required to pre-send your restorable cores to West Coast Classic Cougar. These restored pieces work with both the 1969-70 Standard model Cougar and Mustang boot mouldings (even the reproduction die cast chromed mouldings), and 1969-70 Mercury Cougar XR7...

This option REQUIRES sending your cores in advance. Used stainless steel convertible top trim for the middle section of the exterior boot trim. This is a two piece set of trim, a right and left section, which slip fit together. These pieces work with both the 1969-70 Standard model Cougar and Mustang boot mouldings (even the reproduction die cast chromed mouldings), and 1969-70 Mercury Cougar XR7 convertible top mouldings. Limited supply of used and restored available.Replaces Ford part...

Spot on reproductions of the 1969-70 Quarter Window "Hockey Stick" Moulding priced below what you can have pit free originals re-chromed for. We have found that this 3M product works great for bonding these parts in place permanently. Included with the moulding is super strength 3M double sided, trim tape.Ford part number C9WY-6529035-A.*NOTE* Remember to remove the aluminum bracket from the bottom of your old hockey stick, it is needed to attach to the car and for attaching the outer...

This is the right hand or "Passenger Side" 1/4 panel moulding. Some refer to this as a "Hockey Stick" or "J" moulding. It mounts at the base of the rear side windows and almost always needs to be replaced due to pitting or holes having been drilled in them to fasten these in place.We have found that this 3M product works great for bonding these parts in place permanently.Ford part number C9WY-6529034-A.*Note - Remember to remove the aluminum bracket from the bottom of your old hockey...

This stainless steel passenger side top of the door moulding or upper horizontal door trim was used for 69 - 70 Mercury Cougar XR7 models, including convertible, but is a nice upgrade for a standard Cougar. At this time, it is best to send in your "A" grade cores and have your own moulding / trim pieces restored. Our supply of "A" grade used moulding / trim is very low. After 30 days, core refunds will be given as in store credit that is equal to the core charge amount. Ford part #...

Good used driver side (left hand) moulding / trim with no dents or deep scrapes ready to install on your driver / occasional show car. Expect one or two very small dings and some scratching on the underside where glue in glass has come undone at some point. The vinyl top cars have a wider top edge but a narrow bottom edge where the non vinyl cars have a narrow top edge with a wide bottom edge. However, both cars can use the same piece.Ford part # C9WY-6551726-C.*NOTE* If you have questions...

Good used part with light pitting. This part would be suitable for a driver or a good candidate to have restored. Both studs will be intact.

Good used part with light pitting. This part would be suitable for a driver or a good candidate to have restored. Both studs will be intact. NOTE - When sending in your core, light pitting on the upper edge is acceptable. Heavily pitted trim will not be accepted.

This is the sub-kit you would have received when you purchased a stainless steel service replacement deck moulding for your 1967 - 1970 Mercury Cougar. The original clips used with a 1967 - 1968 aluminum deck lid moulding would have been similar but would have had a plastic shell surounding the metal clip. For more insight on this tricky trunk trim, check out our video below: ...

Unlike our un-restored used door glass trim and are sold in pairs only. If you are doing a concours correct restoration then these would not be for you as they have been "over restored" to a mirror like finish. The down fall of having such a mirror like finish is they get finger prints on them every time you touch them. The good part is they look HOT! Very nice touch to that resto-mod that cannot get enough bling.When sending cores, they must be in good shape or an upgrade core fee will apply....

1969 - 1970 Cougars came factory equipped with stainless trunk mouldings and 1967 - 1968 Cougars came equipped with anodized aluminum trunk lid mouldings. However if you ordered a 67-68 service replacement deck moulding from Ford anytime after 1968 you would have received a stainless steel replacement. We recently obtained 15 of these that were stored improperly where the packaging had deteriorated and the mouldings showed shelf wear. We sent them out to be polished and the results are...

Upper and lower fuel filler door trim pieces for 1969 and 1970 Mercury Cougars, all models. Finish and quality of this reproduction is superior to NOS as shown in the comparison photo below. Notice the blem spot on the NOS on the right? In order to help keep costs down on some of the reproduction items we left off the black detail paint as shown. NOS on the left Repro on the right Looks great assembled. You may or may not want to mask and spray gloss black paint to replicate the stripe like on...

This is right and left hand set of 1/4 panel window mouldings. Some refer to these as "Hockey Sticks" or "J" moulding. It mounts at the base of the rear side windows and almost always needs to be replaced due  to pitting or holes having been drilled in them to fasten these in place. We have found that this 3M product works great for bonding these parts in place permanently. *NOTE - Remember to remove the aluminum brackets from the bottom of your old hockey sticks,...

This stainless steel driver side top of the door moulding or upper horizontal door trim was used for 69 - 70 Mercury Cougar XR7 models, including convertible, but is a nice upgrade for a standard Cougar. At this time, it is best to send in your "A" grade cores and have your own moulding / trim pieces restored. Our supply of "A" grade used moulding / trim is very low. After 30 days, core refunds will be given as in store credit that is equal to the core charge amount. Ford part #...

This stainless steel passenger side top of the door moulding or upper horizontal door trim was used for 69 - 70 Mercury Cougar XR7 models, including convertible, but is a nice upgrade for a standard Cougar. This is a used part, often times it will have small or very minor dents. These stainless steel pieces shine up nicely with 0000 steel wool. Ford part number C9WY-6520934-A. *NOTE* The use of this XR7 unique trim requires the use of different belt-line weather strips than that of the...

This stainless steel driver side top of the door moulding or upper horizontal door trim was used for 69 - 70 Mercury Cougar XR7 models, including convertible, but is a nice upgrade for a standard Cougar. This is a used part, often times it will have small or very minor dents. These stainless steel pieces shine up nicely with 0000 steel wool. Ford part number C9WY-6520935-A. *NOTE* The use of this XR7 unique trim requires the use of different belt-line weather strips than that of the standard,...

Used passenger side (right hand) stainless steel channel for installing the roof side, or upper door and quarter window weatherstripping. Driver and passenger sides are contoured differently and are only for the 1969-70 Mercury Cougar. These channels also have pre-drilled holes for installation and often times the assembly line workers 'made their own holes' so there often times will have additional assembly line holes. Plan on installing a new roof rail weatherstrip item 5645. Shipping will...

Used driver side (left hand) stainless steel channel for installing the roof side, or upper door and quarter window weatherstripping. Driver and passenger sides are contoured differently and are only for the 1969-70 Mercury Cougar. These channels also have pre-drilled holes for installation and often times the assembly line workers 'made their own holes' so there often times will have additional assembly line holes. Plan on installing a new roof rail weatherstrip item 5645. Shipping will have...

Chromed quarter window moulding or 'hockey stick' mounting bracket for the passenger side only of 1969-70 Mercury Cougars. Coupe only, will not fit convertibles. Also attaches the outer window fuzzy or belt line kit component. Aluminum construction, these can be bonded to our reproduction quarter trims. Item cleaned for photos, item shipped will likely have the remnants of the window seal and road tested dirt.Replaces Ford part number C9WY-6529034-A

Chromed quarter window moulding or 'hockey stick' mounting bracket for the driver side only of 1969-70 Mercury Cougars. Coupe only, will not fit convertibles. Also attaches the outer window fuzzy or belt line kit component. Aluminum construction, these can be bonded to our reproduction quarter trims. Item cleaned for photos, item shipped will likely have the remnants of the window seal and road tested dirt.Replaces Ford part number C9WY-6529035-A

Reproduction driver side (left hand) passenger side (right hand) pair of quarter window mouldings / trim with used mounting brackets attached. Some refer to these as "Hockey Sticks" or "J" mouldings. They mount at the base of the rear side windows and almost always needs to be replaced due to pitting. We bond these to the mounting brackets in house with a liberal application of 3M Windo-Weld #08609. The factory bonded them together with 3 studs that were heat peened / swedged. Ford part...

Good used driver side (left hand) moulding / trim for the Mercury Cougar equipped with a vinyl top with no dents or deep scrapes ready to install on your driver / occasional show car. Expect one or two very small dings and some scratching on the underside where glue in glass has come undone at some point. The vinyl top cars have a wider top edge but a narrow bottom edge where the non vinyl cars have a narrow top edge with a wide bottom edge. However, both cars can use the same piece.Ford part...

Good used passenger side (right hand) moulding / trim for the Mercury Cougar that was NOT equipped with a vinyl top. These units will not have dents or deep scrapes and will be ready to install on your driver / occasional show car. Expect one or two very small dings and some scratching on the underside where glue in glass has come undone at some point. The vinyl top cars have a wider top edge but a narrow bottom edge where the non vinyl cars have a narrow top edge with a wide bottom edge....

Reproduction passenger side (right hand) quarter window moulding / trim for the Mercury Cougar. This unit also comes with a used aluminum mounting bracket. Some refer to this unit as a "Hockey Stick" or "J moulding" and it mounts at the base of the rear quarter windows. These mouldings almost always need to be replaced due to pitting or having holes drilled in them to fasten them in place. We have found that this 3M product works great for bonding these mouldings / trim to the mounting bracket...

Reproduction driver side (left hand) quarter window moulding / trim for the Mercury Cougar. This unit also comes with a used aluminum mounting bracket. Some refer to this unit as a "Hockey Stick" or "J moulding" and it mounts at the base of the rear quarter windows. These mouldings almost always need to be replaced due to pitting or having holes drilled in them to fasten them in place. We have found that this 3M product works great for bonding these mouldings / trim to the mounting bracket...

Good used driver side (left hand) moulding / trim with no dents or deep scrapes ready to install on your driver / occasional show car. Expect one or two very small dings and some scratching on the underside where glue in glass has come undone at some point. The vinyl top cars have a wider top edge but a narrow bottom edge where the non vinyl cars have a narrow top edge with a wide bottom edge. However, both cars can use the same piece.Ford part # C9WY-6551726-C.*NOTE* If you have questions...

Good used passenger side (right hand) moulding / trim for the Mercury Cougar that was NOT equipped with a vinyl top. These units will not have dents or deep scrapes and will be ready to install on your driver / occasional show car. Expect one or two very small dings and some scratching on the underside where glue in glass has come undone at some point. The vinyl top cars have a wider top edge but a narrow bottom edge where the non vinyl cars have a narrow top edge with a wide bottom edge....