Home > 1969 Mercury Cougar
All Available Parts - 1969 Mercury Cougar
Products (Click sub-categories above to ONLY display results for that Sub-Category) 5101-5200 of 5310
Sorted By:
Availability:
Display Options:
Availability: Out of Stock
Item #: 10458 -
1969-72 Mercury Cougar and Ford Mustang shifter handle and buttons, for automatic transmissions. This is the base model shifter handle with correct black buttons, and set screws. Deluxe shifters were larger and had simulated leather wrapping. Ford part numbers C8OZ-7213-A, C8ZZ-7C488-A, and C8ZZ-7C488-B. Click on image to enlarge. Check out our video on rebuilding your shifter below: ...
Availability: Out of Stock
Item #: 41380 -
Used automatic shifter bezel / indicator assembly for all Mercury Cougar and Ford Mustang with or without consoles. These are the best used ones from our inventory. These will have some minor issues with the chrome plating and most often need some detailing on the black pebble grain. Consider also purchasing a new seal, shift indicator lenses may or may not meet your requiements. Doesn't meet your requirements? We have very nice quality 1969-70 reproduction shift plate bezels also available....
Availability: Out of Stock, On Order
Item #: 13959 -
Stunning quality and far less likely to crack than the originals. The 67 version was actually a little different than 68 - 73 but you would have to look close to see the difference. Check out our video on rebuilding your shifter below: ...
Availability: Out of Stock, On Order
Item #: 13958 -
Stunning quality and far less likely to crack than the originals. The 67 version was actually a little different than 68 - 73 but you would have to look close to see the difference. Check out our video on rebuilding your shifter below: ...
Availability: Out of Stock
Item #: 16-0075 -
Factory transmission support bracket for use on all 1967 - 1970 Cougars with 390-2V, 390-4V, 427-4V, 428 Cobra Jet engines and C6 automatic transmissions. Ford part number C7ZZ-6A023-B. This part weighs 3.5 pounds and when set on a level surface the height of the mounting hole on the driver side measures 2 3/4" on center and the passenger side is 3 1/2" on center. These "sometimes" will be stamped 390 on the inside.*NOTE* The key identifier on this C-6 unit that separates it from the...
Availability: Out of Stock
Item #: 12872 -
Reproduction of the very hard to find crossmember for any 67 - 70 Cougar or Mustang with the 390 or 428 engine and the C6 transmission. Replaces Ford Part number C7ZZ-6A023-B
Availability: Out of Stock
Item #: 16-0058 -
According to the MPC, this "Transmission Kick Down Control Shaft Rod" is used on all C6 Cougars and Mustangs in 1969, including the 390 and 428 Cobra Jet. Our research and in hand examples off original Cougars would differ. Because of the different intake manifold used on the 390, Autolite carburetor vs. Holley and different exhaust manifolds we have found that the 1969 390 IP with C6 is distinctly different than the 428CJ and stands on its own by not interchanging with any...
Availability: Out of Stock
Item #: 27495 -
NOS power steering ram cylinder dated 6H25 or August 25, 1966. This one is date coded for a very early built 1967 Mercury Cougar or Ford Mustang, including Shelby GT350 and GT500. Bendix manufactured, shows a paint marking and gold cadmium? nut and band. Still has the plastic plugs and cardboard protection on the threaded shaft and drag link stud. Seals presumed to be good, but no guarantees.
Availability: Out of Stock
Item #: 18935 -
Tag marked HBA-BF or HBA-BF1 for use on 1967-68 Cougar and Mustang with power steering pumps originally installed on 289/302/390/427 and all 1968 428CJ engines. Various dates, and could be designated for either a Ford-Thompson (F) or TRW (W) power steering pump. For 1969 dated tags please see the related listing.*Please Note - Current inventory is exclusively 1967-68.
Availability: Out of Stock
Item #: 24266 -
The originals hang at a slightly different angle than the reproductions. Comes as shown with original rubber insulator. New rubber available upon request. Replaces Ford part # C7ZZ-3C510-A, and C7ZZ-3C510-C.
Availability: Out of Stock
Item #: 13875 -
This is a much higher quality bracket than other reproductions. Correct texture and fit. The bracket offered by most companies is just pot metal sprayed gray. Replaces Ford Part #: C7SZ-3A732-B or C7ZZ-3A732-B.
Availability: Out of Stock
Item #: 10582 -
This item will have a refundable core charge added to your order. Multi-year power steering pump, 1967-69, and 1971-73, excludes 1970. When fully assembled you will notice that this year P/S pump has a centered fitting for the pressure hose on the back of the reservoir. Most factory 1970 Mercury Cougar and Ford Mustang have an offset fitting. The only 1970 exception is the R or Q code 428 Cobra Jet engines, they used this pump. Manufacurers note: In place of the paper gaskets, it is...
Availability: Out of Stock
Item #: 31982 -
AMK strut rod hardware kit, course threaded bolts and nuts with cotter pins as shown.
Availability: Out of Stock, On Order
Item #: 26724 -
Although this premium reproduction strut rod bushing kit appears very similar to the economy kit, they are in fact superior. The main difference being that the bushings are made from a higher quality rubber compound.Replaces Ford Part #: C6OZ-3A187-AR.
Availability: Out of Stock
Item #: 24839 -
This listing is for a premium quality pair of 1968 - 1969 original strut rods in grade "A" used condition. What sets them apart from our grade "B" rods is they have a smooth finish, no pock marks from rust. This is for the person who is doing a show car and wants the very best, original correct parts that can be found. The reproductions are made in China and work fine but they are different on every detail and do not come with the specialty bolts that attach the rear on the arm to the lower...
Availability: Out of Stock
Item #: 19239 -
Nice used driver side strut rod that fits all 1968-69 Mercury Cougar and Ford Mustangs. Our good used Western strut rods are the best you will find. No bends, nor damaged threads, not heavily rusted and correct for your Mustang / Cougar and 1968-69 Torino, Cyclone, Ranchero. 1968-69 strut rods are the same as 1970-73 strut rods, but 1968-69 rods have stepped down threads at the end. Ford part number C8OZ-3468-B. Sold as a bare strut rod, we also offer the used hardware for installation...
Availability: Out of Stock
Item #: 19278 -
This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of 50% of our web price for parts delivered in hand or by carrier to our Brooks, Oregon location. If you're not interested in store credit, just shoot us an email and we will let you know if it's is something we can pay cash for. We do not send cash for parts in advance but we often can compensate you within hours of receiving the...
Availability: Out of Stock
Item #: 24840 -
Our grade "B" rods are just as straight as our grade "A" used rods but the will show pock marks from rust after you clean them. One can fill and sand but it will take time. These are still a better value than the Chinese rods we sell.*Note - 1970-73 strut rods work equally well.
Availability: Out of Stock
Item #: 20376 -
Jumbo sized promo guide with lots of great pictures. These are fun to take apart and frame multiple pages. Inside you will find a picture of the "Bee Line Dragway" just off Highway 87 in the middle of the Pima Maricopa Indian reservation, about 6 miles from Fountain Hills, AZ. The timing tower is still there, but the rest is gone.
Availability: Out of Stock
Item #: 12114 -
Used grade "B" bezel for the three spoke rim low steering wheel for the Mercury Cougar XR7. If someone has a roll of material that resembles the burl grain pattern here we would really like to hear from you! the black paint on the edges will need to be redone. We also have examples in the $50 to $100 range that are ready to put on as is but are not show quality like this one. Call and we will walk you through our stock on hand over the phone. We usually have 40 to choose from in all conditions...
Availability: Out of Stock
Item #: 13-0010 -
WCCC developed walnut straight grain kit for rimblow horn pad restorations. Fits all Standard / Decor (non-XR-7) 1969 Cougar hardtop and convertibles. All three pieces were carefully plotted on a computer program to account for their unique contoured shape for each individual insert. Detailed instructions included for preparation and installation. We suggest detailing your horn pad plastic insert, prior to applying this wood grain kit for best results. *NOTE* Fits 1969 rimblow horn pad plastic...
Availability: Out of Stock
Item #: 19409 -
Used grade "A" bezel for the three spoke rim blow steering wheel found in the Mercury Cougar Eliminator or the decor equipped Cougar. This is the best of the best that we have in used and it will look mint.Ford part # C9WA-3D752-A.
Availability: Out of Stock
Item #: 24652 -
Good used part with nice emblem, woodgrain appliqué. If someone has a roll of material that resembles the burl grain pattern here we would really like to hear from you! the black paint on the edges will need to be redone. The engineering number as seen from the back reads C9WA-3D752-A. We also have examples in the $50 to $100 range that are ready to put on as is but are not show quality like this one. Call and we will walk you through our stock on hand over the phone. We usually have 40 to...
Availability: Out of Stock, On Order
Item #: 15533 -
Has correct textured cover. Quality reproduction.
Availability: Out of Stock
Item #: 11716 -
Used Two Spoke Steering Wheel Pad for the 1969 Mercury Cougar or Ford Mustang. Grade B pads will have minor scuffs and scratches and will need to be repainted. Keep in mind that the pad pictured is just a reference photo and not the actual color you will receive. Leave a note in the comments section of your order and we will try our best to match your color.
Availability: Out of Stock
Item #: 27116 -
Used XR7 rear interior panel in white for the driver side (left hand) of the Mercury Cougar XR7 coupe. This was the top of the line interior trim package and could only be had with an XR7 model. XR7 interior codes start with 6, 7, or F, followed by a single letter denoting the color. *NOTE* Arm rests sold separately. Specify if your Cat requires power window cutouts in the comments section.
Availability: Out of Stock
Item #: 23505 -
Good used part with no pitting or scratches. Correct for all 1968 steering wheels and 1969 Cougar's equipped with the standard level interior.
Availability: Out of Stock
Item #: 27115 -
Used XR7 rear interior panel in white for the passenger side (right hand) of the Mercury Cougar XR7 coupe. This was the top of the line interior trim package and could only be had with an XR7 model. XR7 interior codes start with 6, 7, or F, followed by a single letter denoting the color. *NOTE* Arm rests sold separately. Specify if your Cat requires power window cutouts in the comments section.
Availability: Out of Stock, On Order
Item #: 78946 -
New reproduction quarter pillar windlace for the 69-70 Cougar or Mustang. Sold as a pair.
Availability: Out of Stock, On Order
Item #: 78949 -
New reproduction quarter pillar windlace for the 69-70 Cougar or Mustang. Sold as a pair.
Availability: Out of Stock
Item #: 27105 -
Used XR7 rear interior panel in dark red for the driver side (left hand) of the Mercury Cougar XR7 coupe. This was the top of the line interior trim package and could only be had with an XR7 model. XR7 interior codes start with 6, 7, or F, followed by a single letter denoting the color. *NOTE* Arm rests sold separately. Specify if your Cat requires power window cutouts in the comments section.
Availability: Out of Stock
Item #: 27089 -
Used décor rear interior panel in dark red for the passenger side (right hand) of the Mercury Cougar coupe. The décor interior is one level above the base standard interior. Interior code for base standard interiors starts with 1, décor interior codes can start with 3, 5, or E, followed by another letter denoting color. *NOTE* Armrests sold separately. Specify if your Cat requires power window cutouts in the comments section.
Availability: Out of Stock
Item #: 27095 -
Used décor rear interior panel in aqua for the driver side (left hand) of the Mercury Cougar coupe. The décor interior is one level above the base standard interior. Interior code for base standard interiors starts with 1, décor interior codes can start with 3, 5, or E, followed by another letter denoting color. *NOTE* Armrests sold separately. Specify if your Cat requires power window cutouts in the comments section.
Availability: Out of Stock
Item #: 24386 -
Unlike the parts pictured, we only have pitted covers left. At present we have no grade "A" examples. C8MB-5422678-A. Brushed die-cast (with stainless steel look) cover for the chromed grab handle end part number C9MB-5422668-A. These are the smooth or plain ends, the Lincolns used a cover that had scrolling. Used on 1969-70 Mercury Cougar XR7 and various other Lincolns and Mercury full sized cars. These clean up pretty well with steel wool as shown. Keep in mind we have reduced priced...
Availability: Out of Stock
Item #: 24363 -
This is an original chrome lock knob used on 1968 and up Fords with no peeling chrome or obvious scratches. If you compare the originals to the reproductions we have listed you will see a distinct difference. This is for the very particular restorer who really is concerned about detail, especially on prominent pieces like this. Sold individually, very limited supply.Original Ford part number is C8AZ-6221850-A
Availability: Out of Stock
Item #: 10436 -
Larger sized retainer that screws to upper front lip near the quarter glass on all 1969-70 Mercury Cougar hardtops and 1970 Ford Mustang coupes. Ford lists this part as: Retainer - quarter trim panel rear. We see these sometimes installed in the front position at the top of the interior quarter panel next to the window glass, mostly the front position is empty or the factory installed two of the smaller retainers. This retainer helps the top section of the soft trim panels from rattling. The...
Availability: Out of Stock
Item #: 33432 -
Good used arm rest with no cracks, burns or heavy discoloration. No reproductions to this date have been able to correctly match the original in look or feel.
Availability: Out of Stock
Item #: 33429 -
Good used arm rest with no cracks, burns or heavy discoloration. No reproductions to this date have been able to correctly match the original in look or feel.
Availability: Out of Stock
Item #: 33430 -
Good used arm rest with no cracks, burns or heavy discoloration. No reproductions to this date have been able to correctly match the original in look or feel.
Availability: Out of Stock
Item #: 27088 -
Used décor rear interior panel in dark red for the driver side (left hand) of the Mercury Cougar coupe. The décor interior is one level above the base standard interior. Interior code for base standard interiors starts with 1, décor interior codes can start with 3, 5, or E, followed by another letter denoting color. *NOTE* Armrests sold separately. Specify if your Cat requires power window cutouts in the comments section.
Availability: Out of Stock
Item #: 18727 -
Core FMX transmission for a 1970 Mercury Cougar or Ford Mustang. Tag number PHB-E1. Floor shift FMX Transmission. Core transmission only, No bell housing, dip stick, dip stick tube, or torque converter. This is a rebuildable core transmission, removed from a 1970 Mercury Cougar with H code 351-2V engine. Main case inspected for damage. Heavy item, in most cases it can ship UPS ground. Easier if picked up in person.
Availability: Out of Stock
Item #: 14-1000 -
New Permatex RTV gasket dissolver, good for all makes, models, and years. Use this stuff when you want to remove any remnants of those old worn out silicone gaskets made with any of the common gasket makers. Handy item to have on hand so you dont have to keep using your putty knife or screwdriver!
Availability: Out of Stock
Item #: 32408 -
Assembly line used engine lift hook. Passenger side 1969-70 with 428 Cobra Jet engines, including 428SCJ. Triangle shaped, with one single hole for the hook. Not stamped with number. Fits all 1968-70 Ford cars with either R code or Q code 428 engines. Cougar, Mustang, Cyclone, Torino, Talledega, Cobra, Fairlane, Montego, Ranchero etc. Attaches to the passenger side exhaust manifold. There is also a driver side engine lift hook, see related items.
Availability: Out of Stock, On Order
Item #: 33000 -
Reproduction fuel bowl fitting for Holley 4150 carburetors as found on 1967-70 Mercury Cougar and Ford Mustang. All steel fitting, two needed per carburetor. Sold individually. Check the threads in those Holley bowls prior to installation, often times the bowls are bad.
Availability: Out of Stock
Item #: 11-0337 -
Flow thru ventilation, power vent, power ventilation system, comfort stream ventilation, are some of the various names for this rare option found on 1969 Mercury Cougar, Ford Mustang and Shelby Mustang. Back in 1969 it was a $40.02 option. It allowed fresh air to be blown through a center vent. Often confusing, because it looks like half of an air conditioning system.Ford casting number C9ZA-18C299-B. This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to...
Availability: Out of Stock, On Order
Item #: 11-0052 -
C9ZA-18C366-A lower heater duct to floor outlet for Cougars or Mustangs without air conditioning. Used grade "B" part that will have more than one minor defect. It will have a small crack and possibly a broken or missing tab. Almost half the price of the grade "A" piece and works awesome if you don't have one at all. Want to have directed heating, we've got you covered.
Availability: Out of Stock
Item #: 11-0101 -
Used heater box assembly for any 1969-70 Mercury Cougar or Ford Mustang (V-8). Comes as shown, box with damper doors and levers on the side. We recommend buying a heater core and foam rebuilding kit to go along with this. Due to the age, there may be a minor stress crack or blemish, it will be a good used assembly. Note that this does not come with a fan assembly, so you will need to reuse your old one.Heater core IS NOT INCLUDED. This icon means that we're looking to buy this part!WCCC is a...
Availability: Out of Stock
Item #: 11-0106 -
Lower heater duct to floor outlet for Cougars and Mustangs with air conditioning. Used grade "A" part and may have one very minor defect. This part will be damage free. Replaces Ford part number C9ZA-18C366-A.
Availability: Out of Stock
Item #: 11-0033 -
C9ZZ-18A651-B Complete heater and power ventilation system control assembly includes bezel or face plate, knobs, bracket control mounting plate, electrical and vacuum switches. Functional, driver quality, heater control assembly. The power ventilation system was a pretty rare option for 1969-70. It included a center dash register as found on air conditioned cars and directed cool air through the center of the dash. Dearborn cars would have a code "VS" on their body buck tags, and Metuchen...
Availability: Out of Stock
Item #: 11-0049 -
C9ZA-18490-A, windshield defroster nozzle to vent for any 1969 - 1970 Cougars or Mustangs without air conditioning. This part is used and is grade "A." If it does have any minor defects, it will have only one. It might have a small crack, but will not have any broken or missing tabs. If you drive your baby when it is cold and don't have this part, you want it. Why, because it's lame when you have to use your sleeve to wipe off your windshield to see where you are going. It's also a heck...
Availability: Out of Stock
Item #: 11-0050 -
windshield defroster nozzle to vent for any 1969 - 1970 Cougars or Mustangs without air conditioning. This used grade "B" part will have more than one minor defect. It will have a small crack and possibly a broken or missing tab, but it's a heck of a lot better than wiping your windshield with your sleeve.Replaces Ford part number C9ZA-18490-A.
Availability: Out of Stock
Item #: 31061 -
This 1969-70 Mercury Cougar and Ford Mustang shield, was installed at the factory to protect the heater motor from being damaged when the Big Block 390 / 428CJ's were being dropped in. As noted in the factory assembly manuals we sell, they were supposed to be removed once the motor was in place. We have found that more often than not they were left in place as it was probably too time consuming to remove them. Technically they should not be in place on a concours car but practically...
Availability: Out of Stock
Item #: 41706 -
Concourse correct 90 degree heater hose elbow that attaches to the intake manifold and provides proper clearance for the emissions canister and air cleaner housing. Correct for all Boss 302 and 428CJ engines 1969-70.Ford number C9ZZ-18599-A.
Availability: Out of Stock
Item #: 11-4001 -
Used heater blower motor for 69 - 70 Mercury Cougar and Ford Mustang. The reproduction off-shore motors may or may not prove to be as good of value as these good used original FoMoCo motors. To date, all we can find for these cars are foreign made units. Keep in mind our used motors carry a one year warranty and the new motors have a 30 day warranty. Also know that the mounting plate is included for free just for the asking on these used motors. We personally have never used the reproduction...
Availability: Out of Stock
Item #: 33647 -
This unit mounts on the main air chamber, it opens and closes the air vent. NOS or new old stock. This unit is easy to test and can be seen by removing the glove box. Often it is the internal spring that fails on these and if your Cougar or Mustang will not easily change between blowing through the defrost ducts and the floor duct, this unit may be the culprit. Switch assembly, servo control. Tested and working, Ford box.Replaces Ford part # C6OZ-18C311-A. ...
Availability: Out of Stock
Item #: 12895 -
Reproduction grommet that seals the heater hoses and A/C lines where they pass through the firewall on the passenger side. Made from closed cell foam, as opposed to the originals being rubber.* Note - Used starting during the later part of 1969. Compare the evaporator line orientation for both years.
Availability: Out of Stock
Item #: 11-0449 -
Used mounting bracket from a 1969-70 Mercury Cougar or Ford Mustang with factory installed air conditioning. This is the tab that is riveted to the blower housing, the stud goes through the firewall. Bracket with stud only, no other hardware included. Normally this will ship with the old fiberglass remnants still riveted to this bracket. Same bracket at 1967-68, but with a longer stud.
Availability: Out of Stock, On Order
Item #: 11-0335 -
Shaft or rod for the heater core damper door on any 1969-73 Mercury Cougar or Ford Mustang with factory or integral air conditioning. The heater damper door allows air to pass over the heater core in the fiber glass A/C box. Part cleaned for photograph, normally will ship 'as removed'. Inspected for damage or weakness of the metal. Shaft only, door not included, but available. See related parts.Replaces Ford part number C9ZZ-19C774-B.*Note will not work in 1967-68 A/C boxes. ...
Availability: Out of Stock
Item #: 11-0318 -
Original two piece assembly that bolts to the passenger side of your firewall on A/C equipped Cougar's. Comes as taken from parts car. If you own a 1969 Cougar you will need to look at the configuration of the evaporator lines. During the 1969 model year this grommet bracket changed to reflect the running year change. It will look like the 1970 pictured bracket.Ford part # C7ZA-19B589-A.
Availability: Out of Stock
Item #: 11-0330 -
Heater door for any 1967-73 Mercury Cougar or Ford Mustang with factory or integral air conditioning. The heater door allows air to pass over the heater core in the A/C box. This is the smallest door in the A/C box, and the one subject to the most damage from moisture. Part cleaned for photograph, normally will ship 'as removed'. Inspected for excessive rust pitting or weakness of the metal, they all will have a slight amount of metal degradation from being assembled as bare metal. Door only,...
Availability: Out of Stock
Item #: 11-0446 -
This A/C vacuum canister mounts through the passenger side fender apron near the hood hinge. This vacuum reservoir controls, damper doors inside the A/C unit. This unit includes a built in check valve. Used and tested vacuum tank and bracket, also known as the A/C vacuum reservoir. Fits all 1968-70 Mercury Cougars, and is a replacement for 1967's too. We also stock a Grade B version that looks the part, but does not have a working check valve, and will still need a new rubber coating on the...
Availability: Out of Stock
Item #: 11-0320 -
Good used grommet that seals the heater hoses and A/C lines where they pass through the firewall on the passenger side. This part will not have any missing "chunks" but will show hairline cracks most evident where the heater core tubes pass through. Taken from a 1970 Cougar. Ford Part #: C9ZA-19B588-C. * Note - Used starting during the later part of 1969. Compare the evaporator line orientation for both years.
Availability: Out of Stock, On Order
Item #: 11-0037 -
These are getting so hard to find without a broken drain cock or rust in the metal lips. The unit pictured here is typical of what you can expect when you buy out used complete box. Plan on repairing the drain cock or other minor cracks. All doors will be functional, we will not promise the evaporator is good and we do promise the heater core will be bad. We have a few single halves if you need the half without the drain cock. Two versions for 1969-70 Mercury Cougar and Ford Mustang....
Availability: Out of Stock
Item #: 11-0038 -
These are getting so hard to find without a broken drain cock or rust in the metal lips. We have a few single halves if you need the half without the drain cock. Soon we will have every single internal and external part from this assembly listed here, in the mean time give us a ring for those obscure parts! Two versions for 1969-70 Mercury Cougar and Ford Mustang. Difference is the evaporator and the orientation of the tubes. Look for the triangle shaped rubber line seal for the later 1969-70...
Availability: Out of Stock
Item #: 11-0092 -
Item is the lower half only of the air conditioning plenum from a 1969 Mercury Cougar or Ford Mustang. This would be the version found at the beginning and most of 1969. Unique in the way the evaporator lines are configured. The later version and all of 1970 has the box with the triangle shaped cut out for the evaporator lines. The lower section is the portion that has the drain tube that is often broken, you may find a repair done to the ones that we sell. These lower sections may have some...
Availability: Out of Stock, On Order
Item #: 25984 -
Constructed from corrosion resistant copper and brass. Quality replacement part for a job you do not have to do again anytime soon. Replaces Ford Part #: C9ZZ-18476-B. Check out our videos below on how to replace a heater core! We now have separate videos for the first generation ('67-'68) and second generation ('69-'70). ...
Availability: Out of Stock
Item #: 12998 -
Used timing chain cover from a 351W or Windsor engine from 1969-70 Mercury Cougar and Ford Mustang or most any 1969-70 Ford with 351W. Honestly, we have found that most of the 1969 production year came with the C8AE-6059-A timing cover. Cast aluminum construction without excessive damage. Installation bolt kits also available. The C8AE-6059-A timing cover can be used on 1970 302 and 351W engines, as long as you use the 1970 timing pointer. The 1970 timing pointers use alternate...
Availability: Out of Stock
Item #: 17298 -
Rear package tray defrost or defog grille. Fits all 1968-70 Mercury Cougar and Ford Mustangs with the rear defogger option. All of them were black in color. Later they were available in colors. We also have blue available, see our related tab. Replaces Ford part number C8AZ-18C490-B.
Availability: Out of Stock
Item #: 16788 -
Rear package tray defrost or defog grille. Fits all 1968-70 Mercury Cougar and Ford Mustangs with the rear defogger option.Typically you only see black grilles. Later they were available in colors. We have this blue available. Replaces Ford part number C8AZ-18C490-B. This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of 50% of our web price for parts delivered in hand or by carrier to...
Availability: Out of Stock
Item #: 25964 -
WE CAN NOT SHIP THIS PRODUCT INTERNATIONALLY WITHOUT SHIPPING IT AS HAZARDOUS MATERIAL. THIS WILL INCUR HAZARDOUS MATERIAL CHARGES VIA UPS AND SOME COUNTRIES DO NOT ACCEPT IMPORTING THIS PRODUCT. This SEM plastic and leather paint prep is for cleaning surfaces before applying the SEM flexible vinyl paint. Removes mold, grease, oil and other contaminates from leather, carpet, velour and vinyl.
Availability: Out of Stock, On Order
Item #: 12-0082 -
This sporty quarter-zip sweatshirt features a Mercury man on the front left chest, "Mercury" script down the right arm, and a Team Cougar logo on the back. A cool tribute to the winning 1967 Trans Am team, and a great way to represent the brand while staying warm.
Availability: Out of Stock, On Order
Item #: 12-0084 -
This sporty quarter-zip sweatshirt features a Mercury man on the front left chest, "Mercury" script down the right arm, and a Team Cougar logo on the back. A cool tribute to the winning 1967 Trans Am team, and a great way to represent the brand while staying warm.
Availability: Out of Stock, On Order
Item #: 12-0085 -
This sporty quarter-zip sweatshirt features a Mercury man on the front left chest, "Mercury" script down the right arm, and a Team Cougar logo on the back. A cool tribute to the winning 1967 Trans Am team, and a great way to represent the brand while staying warm.
Availability: Out of Stock, On Order
Item #: 12-0086 -
This sporty quarter-zip sweatshirt features a Mercury man on the front left chest, "Mercury" script down the right arm, and a Team Cougar logo on the back. A cool tribute to the winning 1967 Trans Am team, and a great way to represent the brand while staying warm.
Availability: Out of Stock, On Order
Item #: 12-0087 -
This sporty quarter-zip sweatshirt features a Mercury man on the front left chest, "Mercury" script down the right arm, and a Team Cougar logo on the back. A cool tribute to the winning 1967 Trans Am team, and a great way to represent the brand while staying warm.
Availability: Out of Stock, On Order
Item #: 16174 -
Used switch for the rear defog or defogger fan on any 1969 Mercury Cougar, 1969 Standard Cougar, and 1969-70 Mustang coupe or hardtop. Original switch with attached wiring harness. Tested and working two speed switch. Comes as shown with chrome knob marked "DEFOG". Some examples may have minor pits in the chrome knob. Wiring marked C9WA-18C498-A. Excludes all convertible models and Mustang fast backs.Replaces Ford part number C9ZZ-18578-A.*Note - is not technically correct for 1970 Mercury...
Availability: Out of Stock
Item #: 16230 -
Used wiring harness that goes from the rear of the dash all the way to the blower motor in the package tray. This same wiring was used on all 1969-70 Mustangs and Cougars. 1970 Cougar XR7 models have a slightly different configuration, but utilize the wire harness.Replaces Ford part number C9WB-18C394-A.
Availability: Out of Stock, On Order
Item #: 14-0076 -
New Dark Argent spray paint for the 69-70 Cougar or Mustang. This paint is designed for the 70 Mustang Mach 1 grille and rocker panels, but is a great match for the argent color on your Styled Steel Wheels.
Availability: Out of Stock, On Order
Item #: 14-0050 -
New high temperature enamel for painting your block and underhood parts. So far, the best match has been the VHT brand, SP125 "Dark Ford Blue" paint (sometimes called "Ford Corporate Blue"). This enamel resists heat up to 550 degrees so it's a great paint to use on your engine. Dry to touch in 30 minutes and ready to handle in 1 hour. It's also resistant to all types of automotive fluid. Once you get this stuff on, it will not flake, crack or peel. ...
Availability: Out of Stock
Item #: 23232 -
Used plug and wiring pigtail for the brake light warning switch located on the drum or disc brake distribution block mounted to the driver side fender apron. This is a plug and section of wire for repairing the underhood harness. Specific to 68 - early 70 Cougars and Mustangs.The only difference between the late and early pigtail is that the early plug is black and the late plug is white. No difference in wiring.
Availability: Out of Stock
Item #: 14-0071 -
Chassis black aerosal paint for all 1967-73 Mercury Cougar and Ford Mustang engine compartments. High temperature (advertised up to 350°). Manufacturer boasts resistant to cracking and flaking, chemical resistant to gasoline and brake fluid (but don't let brake fluid accumulate). *NOTE* Chemicals can only ship UPS ground only. Please, no foreign orders or USPS shipping allowed.Check out our video below on chassis upgrades: ...
Availability: Out of Stock
Item #: 41456 -
Stainless steel version features extra corrosion protection with correct zinc chromate plated fittings and are exact copies of the originals with color coded fittings.
Availability: Out of Stock
Item #: 24536 -
Power disc brake distribution block with proportioning valve. Mounts to the driver side fender apron with two nuts. Plan on testing and or rebuilding before installation. Rebuild kits available here. You'll also need hard lines and the brake warning switch, which is available new or used. Ford part # C8ZZ-2B257. Here’s a video to help you rebuild the distribution block so that you can corral your Cat or Pony without fearing for your life. ...
Availability: Out of Stock
Item #: 32846 -
New old stock Bendix master cylinder for 1968-69 Mercury Cougar and Ford Mustang with factory power disc brakes. This is a Bendix manufactured MC with proper 2227161 number and stop bolt on the bottom. Also has the dimple forward of the front brake line. Includes a new cap with diaphragm as shown. The cap is not assembly line correct as this is a service replacement part.*Note even though this is a brand new unit, it should be tested for leaks prior to installation. Things happen when...
Availability: Out of Stock
Item #: 31223 -
This rod was used on the Bendix brand booster (crimped together case). It measures 5 3/4" long. Used on many Ford products including Torino, Cyclone, Ranchero, Cobra, Fairlane and others. This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of 50% of our web price for parts delivered in hand or by carrier to our Brooks, Oregon location. If you're not interested in store credit, just shoot...
Availability: Out of Stock
Item #: 31051 -
Reproduction front seal for the Bendix brake booster used on all 69 - 70 Cougars and Mustangs as well as many other FoMoCo products that use this size of Bendix booster. This seal prevents brake fluid from entering the booster cavity once the master cylinder fails.
Availability: Out of Stock
Item #: 15301 -
New master cylinder for the Mercury Cougar or Ford Mustang equipped 4 wheel power disc brakes. This unit can be used with the Bendix and Midland boosters. Bore size: 1" WARNINGS: Do not attempt to use a 1970 booster on a 1967-69 Cougar as failure will occur within minutes! Never bleed your brakes on a power brake car with the car running. The pedal will over extend the rod into the booster and break internal parts. This is not covered under warranty. ...
Availability: Out of Stock, On Order
Item #: 30568 -
Reproduction pair of mounting nuts for any 68 - 70 Cougar or Mustang with power brakes.
Availability: Out of Stock
Item #: 30967 -
This option REQUIRES sending your core in advance. Here are the advantages of pre-sending your core:We can core match your booster. Boosters that are rebuilt using a superior quality core are always reserved for core matching. If your core is average or below average, you may be able to pay to upgrade to a rebuilt booster that started the rebuild process as a superior quality core.You can find out the quality of your core before paying a core charge and avoid unnecessary core charges....
Availability: Out of Stock, On Order
Item #: 12-0042 -
These new XR7 shirts are bold and elegant, just like the cars they represent. On the front left chest is a recreation of the C-pillar badge found on 1967-1968 Cougar XR7's, and on the rear is a nice big crest that mirrors the 1969-1970 XR7 emblems.Screen printed on quality 100% cotton black tees, these shirts are the perfect way to display your allegiance to the classiest muscle car of all time: the Mercury Cougar XR7. Oh, and they make a great gift, too. ...
Availability: Out of Stock, On Order
Item #: 12-0043 -
These new XR7 shirts are bold and elegant, just like the cars they represent. On the front left chest is a recreation of the C-pillar badge found on 1967-1968 Cougar XR7's, and on the rear is a nice big crest that mirrors the 1969-1970 XR7 emblems.Screen printed on quality 100% cotton black tees, these shirts are the perfect way to display your allegiance to the classiest muscle car of all time: the Mercury Cougar XR7. Oh, and they make a great gift, too. ...
Availability: Out of Stock
Item #: 12-0044 -
These new XR7 shirts are bold and elegant, just like the cars they represent. On the front left chest is a recreation of the C-pillar badge found on 1967-1968 Cougar XR7's, and on the rear is a nice big crest that mirrors the 1969-1970 XR7 emblems.Screen printed on quality 100% cotton black tees, these shirts are the perfect way to display your allegiance to the classiest muscle car of all time: the Mercury Cougar XR7. Oh, and they make a great gift, too. ...
Availability: Out of Stock
Item #: 12-0045 -
These new XR7 shirts are bold and elegant, just like the cars they represent. On the front left chest is a recreation of the C-pillar badge found on 1967-1968 Cougar XR7's, and on the rear is a nice big crest that mirrors the 1969-1970 XR7 emblems.Screen printed on quality 100% cotton black tees, these shirts are the perfect way to display your allegiance to the classiest muscle car of all time: the Mercury Cougar XR7. Oh, and they make a great gift, too. ...
Availability: Out of Stock
Item #: 64512 -
As seen in our YouTube video, this is a representation of the used, rebuilt and reproduction parts that we recommend you purchase to convert to disc brakes. If you do purchase this package we will insist on speaking with you prior to shipping as you may want to substitute parts based on what year your car is, manual or automatic and what style booster you prefer. Also know that if your car already has power drum brakes we will be able to reduce the price substantially as no booster or pedal...
Availability: Out of Stock
Item #: 17783 -
Correct reproduction available only from WCCC. Notice our consoles feature the correct Burl grain xr7 applique and correct for xr7 3 hump lid. Only available in black, we suggest SEM flexible coating if you need to color them to match your interior. We find that custom mixing the paint will get you better results than their off the shelf selections. Inquire with your local Automotive paint supply house.
Availability: Out of Stock
Item #: 33048 -
NOS 1983 Ford manual on how to read and understand vacuum diagrams. Although it's technically made for older cars, it has tons of useful information on how to decode diagrams. Includes sections on vacuum theory and applications, devices, hoses, schematics and system diagnosis. This handy book has information pertaining to how the engine creates vacuum, the carburetor and it's vacuum pressure regulation characteristics as well as air intake, fuel induction, emissions and ignition. As an...
Availability: Out of Stock
Item #: 24740 -
C9WY-17755-A Front bumper mounting bracket, 1969-70 Mercury Cougar driver side.
Availability: Out of Stock
Item #: 12-0039 -
These new XR7 shirts are bold and elegant, just like the cars they represent. On the front left chest is a recreation of the C-pillar badge found on 1967-1968 Cougar XR7's, and on the rear is a nice big crest that mirrors the 1969-1970 XR7 emblems.Screen printed on quality 100% cotton black tees, these shirts are the perfect way to display your allegiance to the classiest muscle car of all time: the Mercury Cougar XR7. Oh, and they make a great gift, too. ...
Availability: Out of Stock, On Order
Item #: 41787 -
This is a complete kit for front and rear. If you own a 71 - 73 and then you will need two more bolts. mercurycougar.net: I was in Salem on business Monday when I decided to give West Coast Classic Cougar a call. Don was gone but Lin was there, talk about a nice guy I looked around the shop and Lin got me the parts I needed for my 68 Coupe. I am sure Lin was busy but he took the time to answer any questions I had, swapped a few stories and gave me a real good deal. I recommend anyone needing...
Availability: Out of Stock
Item #: 33409 -
1969 Cougar XR7 1/43 scale mini trophy model kit. No glue required, simply snap together the pieces and put the car inside the included plastic "trophy case". We haven't seen many of these collectible kits around the web, it's definitely a hard to find example. Previously owned, there's no plastic bag to contain the parts like the usual model kits, everything comes inside the clear plastic case show in the photos. Some pieces have broken away from the attaching ribs, but it looks like...