Your cart is empty!
Our shopping cart requires the use of cookies. If you have your cookies disabled, please enable them for our site to place an order. If you have cookies enabled and have added an item to your cart, but you are still seeing this message, that could indicate that the cookie for our shopping cart is corrupted on your computer.You should be able to fix this by either:
Buy Details
These two piece adhesive XR7-G emblems are made by the OEM supplier to Ford. As you compare these to the now obsolete version supplied through Ford back in the day, you will see these are nowhere close to the original version. One may deduct that since we have the lowest advertised price with the...
These emblems can be used anywhere from your toolbox, to the dash or trunk and anywhere in between. Makes a great accent to other fender emblems or door panels. Peel and stick.Sold as a pair.
These two emblems were sold separate when ordered as a service replacement part. We sell them as a pair. Located on the passenger side of the trunk, these are a peel and stick with no mounting studs. Ford part # C9WY-6542532-A & C9WY-6542532-BWe often get asked about where to place 69-70 XR7 and...
Adhesive backed, located on the right side of your deck lid. We often get asked about where to place 69-70 XR7 and Cougar adhesive emblems. Based on personal experience and pictures from the original Ford archives the answer would be "Pretty much wherever you think looks best". Often, as you...
These are sold as a pair and are of marginal quality. The material is much softer than original, the chrome is of a low quality and compared to original the detail is not nearly as crisp. ...
NOS GT-E Fender badges. Sold as a pair, driver side shows a C7WX-16099 casting number and the passenger side shows a C7WX-16098 number. ...
Reproduction pair of quarter panel scripts with black trim for the 1968 Mercury Cougar. The correct version had no black paint around the letters. This is a one time only limited run of this custom emblem, and when they're gone they're gone! *Only sold as a pair ...
New product! These 1967 XR-7 "hash marks" or "ribs" are being offered as set of 14. Seven of these were used on each side. These are correct only for the 1967 XR-7 but will fit nice on any 1967 - 1970 Cougar and are a nice alternative to the very large aluminum rocker mouldings used in 1968 - 1970...
New product that is in stock and ready for shipment now! Concours quality, perfect fit and a great value for the money. These little emblems are often the first thing one sees as they approach your car as they are at eye level. These emblems are located on the "C" pillars of your 67 - 68 Cougar...
Concours quality, perfect fit and a great value for the money. These little emblems are often the first thing one sees as they approach your car as they are at eye level. These emblems are located on the "C" pillars of your 67 - 68 Cougar but can also be used on a 71-76 Cougar with little or no...
This small sized Cougar emblem (1 3/8" long) was used on 1969 - 1973 Cougars without AC. It was affixed to a block off plate in the very venter of the dash by two peened over die cast studs. It will glue back in place nicely and many Cougar fans have found fun "custom" applications for this...
Rare Cougar only GT emblems. The Mustang GT emblems had different stud locations. These were used on 1968 Mercury Cougar GT models. This emblem shares the exact same pin locations with the 1968 6.5Litre emblem, so the factory could punch holes and installed the tubular nuts in...
This Super Cobra Jet emblem was never used on a Cougar, but is the Cobra Jet emblem used on the Hood Scoop for 1969-1970 Mustangs. It is also an attractive emblem for your custom application. Thanks for the plug Mark!: "My first deal with Don was clear back in the 1980s...
Good used emblem with no bends, but will be scratched. Will need new adhesive tape as these did not come with studs. For any Cougar, but only came on 1969-70 Standard Models, and all 1971-73 Mercury Cougars. 1971-73 XR7 and Standard Models, as well as convertible.We often get asked about where to...
This is a used coral with a new background decal and walking cat emblem. We ship the three parts unassembled so you can re-chrome the corral if you desire. The corral will not be perfect but it will not be heavily pitted either. You can expect the part you receive to resemble the one pictured...
This used grade B emblem will have good chrome and mounting studs, but the plexi center will be faded. These can be opened up and repainted from the backside. The paint can be obtained from stores that sell modeling supplies. These mount on the lower part of the roof behind the quarter...
This used grade A emblem will have good chrome and mounting studs and plexi center. Ford engineering number on backside is D1WB65517A20-AB. We also offer new barrel nuts for installation. This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury...
This was an adhesive emblem and has long since fallen off most cars or was removed when the car was painted. We often times have driver quality emblems available, but be aware, they will have some pitting issues.Our reproduction 67-68 pillar emblem is a good substitute.Original Ford part number...
Used driver side (left hand) XR7 door panel emblem for the Mercury Cougar. The emblem shown is not faded, most likely the emblem you receive will be faded from black to a bronze color. Keep in mind the cat always walks forward. Sold individually. This icon means that we're looking to buy this...
Used XR7 door panel emblems for the Mercury Cougar. The emblems shown are not faded, most likely the emblem you receive will be faded from black to a bronze color. Keep in mind the cat always walks forward. Sold as a pair.
Used passenger side (right hand) XR7 door panel emblem for the Mercury Cougar. The emblem shown is not faded, most likely the emblem you receive will be faded from black to a bronze color. Keep in mind the cat always walks forward. Sold individually.
These fender emblems look much like the 1968 quarter panel emblems but differ in that they have longer studs that fasten via barrel clips as opposed to a speed nut used on the 1968 quater panel emblems. The Ford casting number on the backside is D1WB-16098-AA. For the money, The 1968 repro quarter...
Good used pit free emblem that would be good for restoration. Notice the clips are in place and there are no cracks in the plastic backing. The example picture of the installed emblem is what they looked like when restored. These mount on the lower part of the roof behind the quarter windows....
Since our restored emblems look so good we have a hard time selling NOS these days which works out just fine as we only seem to be able to obtain 1 of these every few years. Keep in mind your used cores have trade in value against this NOS part. Casting number seen on back side for the assembly is...
This is the foil insert / decal found on a non XR7 Cougar. It's located just below the center rectangular dash vent / register. It measures 6" X 3/8".
Good used "C" pillar emblem for your XR7 with no obvious pitting. These mount on the lower part of the roof behind the quarter windows. This part of the roof is also known as the 'C' pillar.Ford part number C7WY-6528818-B1 Hi Don: Thank you for fixing me up with the XR-7 pillar emblems. I...
Due to corrosion caused from the exhaust this used emblem will most likely have poor quality chrome. The emblem shown would be the very rare exception.
NOS "C" pillar emblem for your XR7. These mount on the lower part of the roof behind the quarter windows. This part of the roof is also known as the 'C' pillar. Ford part number C7WY-6528818-B1
New Old Stock "G" and "T" 1967 Mercury Cougar and Ford Mustang individual fender letters. There were two ways that the cars were called out as GT's. Two individual letters and a single box with "GT" inside. These letters were also used on 1970-71 Mercury Cyclone. Both letters sold...
Tubular or barrel nut for attaching our reproduction "C" pillar XR7 emblems with studs. We found these fasteners to install the emblems without disturbing the headliner of a 1967-68 Mercury Cougar. These are also suitable for installing this emblem onto the trunk lids of 1971-73 Mercury Cougar XR7...
Grade "B" original metal emblem for your Eliminator or Standard model Cougar. Grade B emblems will have pitting and faded or missing paint. We rarely ever get flawless examples of this particular emblem as the original plating was substandard (in our opinion). This emblem was used on the...
Grade A used, trunk emblems for 1969-70 XR7 models. We will very seldom have this in stock, the alternatives are grade B used or reproduction. Please see related items below. We often get asked about where to place 69-70 XR7 and Cougar adhesive emblems. Based on personal experience and pictures...
The 1967 XR7 did not have rocker panel mouldings as did the 1968 - 1973 XR7 Cougars. All 1967 XR7 models came equipped with these "Hash" marks fastened to the rear of both rockers, at a rear tilting angle. Both sides received seven ribs, held by two Phillips screws each for a total of fourteen...
These are NOS Mercury Cougar XR7-G dash emblems. The version supplied these days from the OEM supplier do not have as definitive of cross hatch pattern and the edges are not as sharp. Another quick way to discern between NOS and new when original packaging is absent is to look at the back side....
Found on the lower right corner of all 1971 - 1973 Cougars equipped with the XR7 Interior package. Both mounting studs will be in place and it will have a nice overall finish. Ford engineering number as seen on the backside is D1WB-65061A58-AA.
Nice reproduction of the factory installed 390 engine designation ornament or badge. Also found on 1968 - 1969 Ford Fairlane, Torino, Ranchero, and Mercury Cyclone and Montego. Attaches with barrel nuts from the rear of the fender.Sold individuallyReplaces Ford Part #: C8OZ-16228-D. ...
Due to the fact these were glued on, they are often missing. Separate "XR" and "7", Grade B used, good for a daily driver. We often get asked about where to place 69-70 XR7 and Cougar adhesive emblems. Based on personal experience and pictures from the original Ford archives the answer would be...
These Mustang emblems have the incorrect pin placement for the 1968 Cougar so if you have original GT fenders you will have to drill new holes. Once mounted they look correct. Replaces the C7ZB... individual casting numbers. Licensed by FORD ...
These always are peeling. Located on the right side on the dash face...
Poor chrome, for use as a core to be restored.
Used front fender extension "Cougar" script. The one you receive may not look as good as the one pictured but will be very close in condition, expect one of the four studs on the back to be missing. Ford Engineering number as found on the backside: C9WB-16098-B Ford number C9WB-16098-A. Note that...
Used COUGAR Script Quarter Panel Emblem for the 1969 and 1970 Mercury Cougar
Grade "A" pit free original metal emblem for your Eliminator or Standard model Cougar. If you look closely at our picture you will in fact see tiny imperfections in the chrome. We rarely ever get flawless examples of this particular emblem as the original plating was substandard (in our opinion)....
Same as the emblem used on the trunk lid of the 1967 -1968 Cougar.
This Mercury script emblem is mounted onto the driver side fender extension. This is an original part still in the Ford box, engineering number on the back of the emblem reads C7WB-16098-A, Ford part number is C7WY-16604-A.
These fuel door Mercury crest emblems have been lovingly restored by a long time Cougar enthusiast. They have been carefully repainted the correct colors and will really liven up the looks of the rear of your 1969 - 1970 Cougar. This crest was used on all models except the 1970 Eliminator. The...
These fuel door Mercury crest emblems are a close to original reproduction. They are an economical alternative to brighten up the looks of the rear of your 1969 - 1970 Cougar. This crest was used on all models except the 1970 Eliminator. To remove your emblem we suggest grinding down the studs on...
Used Grade "A" center grille emblem for the 71 - 72 Standard Cougar. Most likely will show some fading, no pits. Ford part number D1WY-8A223-A
Used Grade "B" center grille emblem for the 71 - 72 Standard Cougar. Will have fading, pitting and the plastic lens area will need to be restored. Ford part number D1WY-8A223-A
Decent reproduction of the 69-70 Cougar fender extension COUGAR script. This emblem was used for 2 years only and was located on the driver side front fender extension (fender cap). The originals came with speed nuts but these have push on clips from the back which means they are easier to install...
Used front fender extension "Cougar" script. The one you receive may not look as good as the one pictured but will be very close in condition, expect one of the four studs on the back to be missing. Ford Engineering number as found on the backside: Ford number D0WB-16098-A. Note that the...
NOS never installed 390 engine designation ornament or badge. Also found on 1968 - 1969 Ford Fairlane, Torino, Ranchero, and Mercury Cyclone and Montego. Attaches with barrel nuts from the rear of the fender. Sold individually Replaces Ford Part #: C8OZ-16228-D. ...
This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of 50% of our web price for parts delivered in hand or by carrier to our Brooks, Oregon location. If you're not interested in store...
Good used emblem that is not warped and still has the silver paint intact. Don, Thought you might like to see another success story due to help from W.C.C.C. Attached is a picture of my 67 XR7, Lime Frost with Saddle interior. Thanks for all your help and advice. You and your team made a dream...
These were originally painted argent silver with the back ground painted semi-gloss black, they were not chromed. This emblem was used on all 1968 Cougar steering wheels with the exception of the XR7-G.
Good used plastic emblem with no peeling chrome. This was used on all models except XR7 on the right side. We also have the metal version of this emblem available.
Used 6.5 litre Grade A (390) fender emblem for the Mercury Cougar. We rarely get these in fantastic condition and most of what we get looks like the one pictured on our grade B listing with several minor blemishes. No studs will be broken off due to someone thinking they pry off as opposed to...
Invest the big money elsewhere...Here is a NOS part we do not suggest paying the extra money for. These NOS emblems are not as good as the reproductions that cost less than half. The chrome is far superior, the studs stronger and the way they are assembled is much better on the reproductions. The...
These were on the lower rear portion of early 1967 390 GT Cougar fenders. In later 67 and 68 the separate G and T letters were used on the Mercury Cougar. Comes with replacement tubular nuts as shown. Other applications include 1967 Mercury Cyclone GT and 1968 Mustang GT. The GT rectangle badge...
Good used emblem with both studs intact, no obvious pitting or scratches. This item will have a faded center decal, and you will need a new decal. You can either add a note to the order asking that we contact you about upgrading to an emblem with less fade for a upcharge, or get a...
COMING SOON Beautiful reproduction C pillar emblem for the 69 - 70 Cougar XR7. This part is also known as the shield or outside roof side ornament. The attention to detail on this exact copy is really impressive. Kudos to Daniel Carpenter Mustang for providing yet another outstanding part. Sold...
Used Driver Side / Right Side Fender Extension Emblem for the 1967 and 1968 Mercury Cougar
This adhesive plaque was placed in front of the shifter on XR7-G models with a factory installed four speed manual transmission. The XR7-G shift knob had a walking Cat on the face of the knob instead of a shift pattern.
Very difficult to find, delicate aluminum quarter panel emblem in the original Ford box. Ford part number is C9WB-6525622-A, casting number on back reads C9WB-65291B62-AYou can reference the above pictures for correct dimensions, as taken from one of our cars using an original script emblem....
This is one of the smallest "Cougar" emblems ever put on a Mercury Cougar. Only the 70-73 two spoke cat and xr7-G shift handle Cougar was smaller. It is also the most delicate! Very unusual to find the tail and all limbs intact on this fragile little kitty. Silver spray paint will make this cat...
This "Stick On" Cougar rear deck emblem was only used on models without the XR7 package. They are often missing as once the factory double sided tape dries out they are often lost forever. We also have a few very nice used examples in stock.We often get asked about where to place 69-70 XR7 and...
This little emblem was used only on the two spoke steering wheels from 1969 - 1973. We can pretty much guarantee one if not both of the two mounting studs will be broken but because of the way it fits into the recess of the steering wheel pad, gluing it into place is not a problem. We rarely have...
This grille background piece requires you remove your Cougar emblem before installing. To remove the cat emblem you will need to grind from the backside and epoxy the emblem back in place after-wards. Vast improvement over your current faded, dinged part. Not for use on the xr7. ...
Faded but good used emblem with aluminum foil background. If you push on the swedged aluminum studs from the backside these will easily remove. The standard grill emblem with a walking cat uses the same stud configuration as XR7 so you can exchange emblems from one to another. ...
These are sold individually, two required per car. This is the aluminum emblem / decal which mounts on the center of all of the 68-73 scuff plates. Features raised script like original. Adhesive backed with a protective coating that peels off after installation. Replaces Ford Part #:...
Two required per car, right is the same as left. Good used Cougar emblem with no pits, deep scratches or broken studs.
Good used emblem with no missing studs, cracks or pitting. We rarely have this one in stock.
This vinyl piece glues to the center of your block off plated on Cougars not equipped with AC. These often times have shrunk slightly over time. We cannot guarantee to always have all the colors in stock. Call for color availability or put desired color into the comments section of your order. ...
Rare find in NOS form! 1969 standard model Cougar, passenger side dash plate. Replaces Ford part number C9WB-6504460-A.
Located on the right hand dash panel of your XR7, requires drilling to remove properly.
These were obtained from the original manufacturer and have never been mounted. Very rare find!
Original part in Ford box, part number C9WB-16098-A, casting number as seen on back is C9WB-16098-B
Ford offered the 1973 Mercury Cougar hood emblem in two versions as a service replacement part. It is very rare to find them new in the box with the chrome center hood moulding, usually they are found without the chrome. This was found at the Spring 2007 Ford Carlisle show. Once its gone I doubt...
Very nice reproduction of the steering wheel hub decal with the walking cat to fit the new Shelby steering wheels. Chrome outer rim with plastic black and silver horn button in the center.
Used grade "A" horn center / pad in saddle for the Mercury cougar. This is the best used example of a 1967 horn center / pad. Rarely do we have more than one center as nice as this one in stock but we'll do what we can to get you a good pad. This unit includes a reproduction center emblem and...
Used grade "A" horn center / pad in black for the Mercury Cougar. This is the best used example of a 1967 horn center / pad. Rarely do we have more than one center as nice as this one in stock, so we'll do what we can to get a good pad for you. This unit includes a reproduction center emblem and...
Used grade "A" horn center / pad in light blue fro the Mercury Cougar. This is the best used example of a 1967 horn center / pad. Rarely do we have more than one center as nice as this one in stock but we'll do what we can to get you a good pad. This unit includes a reproduction center emblem and...
Used grade "A" horn center / pad in aqua for the Mercury Cougar. This is the best used example of a 1967 horn center / pad. Rarely do we have more than one center as nice as this one in stock but we'll do what we can to get you a good pad. This unit includes a reproduction center emblem and...
No... Mercury never made an emblem "just" like this one but demand dictated we produce it! This emblem has a 3M adhesive backing and looks and measures just like a 1968 quarter panel script or the front fender script found on a 1971 - 1973. Many people do not like the looks (or price) of the 67...
This little emblem was used only on the two spoke steering wheels from 1969 - 1973. We can pretty much guarantee one if not both of the two mounting studs will be broken but because of the way it fits into the recess of the steering wheel pad, gluing it into place is not a problem. The tail will...
This is the correct emblem that came in the center of the hood moulding on a 1973 Standard model Mercury Cougar. It would not look out of place on an XR7 but of course would not be correct.Ford part # D3WY-16637-A. This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS...
This is the correct emblem that came in the center of the hood moulding on a 1973 XR7 model Mercury Cougar. The price is absolutely ridiculous, I agree. Years ago when they sold for $250 I thought THAT was insane! Replaces Ford part # D3WY-16637-B. ...
Used Grade A condition 6.5 litre (390) aluminum fender emblem / badge for the 1967 Mercury Cougar. We rarely get these in fantastic condition and most of what we get looks like the one pictured with several small blemishes. Often, one of the two studs will be broken off due to someone...
Great quality for the money, but you will have a gap showing around the perimeter. When looking at the backside of these XR7-G emblems, you will see the green vinyl backing on the two sided tape. A NOS emblem, (original emblem sold by Ford) will have green paper backing. These are not technically...
Good used center with no crack, missing paint or broken mounting tabs. This was used on all 1969 Cougars with a three spoke wheel except the XR7.
Very rarely do we find one like this example that shows no sign of fading. This is for the person who is trying to achieve a very high level of preservation / restoration.
Good used center with no cracks and an average amount of fade most noticeable in the red portion of the emblem. Many of these emblems are broken or missing because people think this is the horn button and if they just push harder the horn will sound!
Excellent reproduction of the passenger side 1967-68 Mercury Cougar "Cougar XR7" dash panel emblem. Nice reproduction with locating pins that attach to the woodgrain dash panel on the passenger side of all 1967-68 XR7's (excludes the special edition XR7-G models). You can view the photo above for...
Reproduction emblem for the 390 engine designation. Never used on a Cougar, but an attractive emblem for customizing. Measures 3 1/8" x 3/4" and has two mounting studs.Replaces Ford part # C9ZZ-16637-D.
Reproduction center emblem for the 69 Cougar rim blow steering wheel.
Used Grade B condition 6.5 litre (390) aluminum fender emblem / badge for the 1967 Mercury Cougar. We rarely get these in good condition and most of what we get looks like the one pictured with several pits and small blemishes. Often, one of the two studs will be broken off due to...
Reproduction center grille emblem background. This decal is only made with the "7", so you will need to remove the "X" and "R" from your existing decal and adhere them to this new one. You can clean those letters up with some extra fine polishing steel wool. The standard grill...
Used Grade B 6.5 litre (390) fender emblem for the Mercury Cougar. Most of what we get looks like the one pictured with several blemishes. Often one or more of the four studs will be broken off due to someone thinking they pry off as opposed to being held on from the backside with speed...
This emblem was located on either side of the quarter panel in 1968 and both front fenders in 1971 - 1973. The studs on the 71-73 were a little longer but this 1968 emblem is an excellent substitute. Fantastic quality part... In our experience, we have found that you would have to obtain several...
Found on the C pillars of a 1971 - 1973 Mercury Cougar XR7 Coupe. We rarely get good used examples of these emblems as they are always badly faded. These mount on the lower part of the roof behind the quarter windows. This part of the roof is also known as the 'C' pillar.
Ford part number is C7WY-16098-A, casting number as seen on the back of the emblem is C7WY-16720-A. Very rare find, only used on 1967 non GT cars equipped with the S code 390.See related item Barrel nut if missing attaching clips. 3/16 inch stud.
This is a very nice reproduction that we have all needed for many years! You might want to buy a new Cougar walking cat emblem if you replace this background decal as it requires breaking the studs off your old emblem to get it off. Do you want to replace those worn out actuators yourself or are...
Good used pit free emblem. We now have the black background decal in reproduction form. Casing number: C9WB-18B000 Do you want to replace those worn out actuators yourself or are you looking for some great information on aligning the grille in your Cat? The videos below are your ticket! ...
Good used center with minor cracking, missing paint or maybe even a broken mounting tab. This was used on all 1969 Cougars with a three spoke wheel except the XR7.
This is the correct size walking cat decal for your eyelid door on the 1967 - 1969 Cougar. It has the studs in the exact place as the originals. You will need this emblem when changing out our 1967 - 1969 background decals as you will have to break the original studs to remove the cat. Also great...
Reproduction 6.5 litre (390) fender emblem for the Mercury Cougar. These were used on all XR7G models with an S or X code 390, on other Cougars they were used with the Cougars that came equipped with a 390, but without the GT option package. Unlike the originals these do not have mounting studs,...
This is a used fuel door insert we have cleaned up, painted the background black and installed a 1967-1969 headlight door walking cat emblem on. The original 1970 ELIMINATOR piece that this resembles had a smaller sized cat so this is not exactly correct for your original 1970 Eliminator. ...
NOS front fender extension "Cougar" script. Ford Engineering number as found on the backside: Ford number D0WB-16098-A .
NOS front fender extension "Cougar" script. Ford Engineering number as found on the backside: Ford number C9WB-16098-B.
Used grade "A" horn center / pad in dark ivy gold / dark green for the Mercury Cougar XR7. This horn center / pad will fit any 1967 Cougar, but the ivy gold interior color was a XR7 option only. his is the best used example of a 1967 horn center / pad. Rarely do we have more than one center as...
Used grade "A" horn center / pad in parchment / off-white for the Mercury Cougar. This is the best used example of a 1967 horn center / pad. Rarely do we have more than one center as nice as this one in stock but we'll do what we can to get you a good pad. This unit includes a reproduction center...
Used grade "A" dark blue horn canter / pad for the Mercury Cougar XR7. This will fit and 1967 Cougar, but the dark blue interior color option was XR7 only. This is the best used example of a 1967 horn center / pad. Rarely do we have more than one center as nice as this one in stock but we'll do...
Used grade "A" horn center / pad in dark red / maroon for the Mercury Cougar XR7. This horn center / pad will fit any 1967 Cougar, but the dark red / maroon interior color was a XR7 option only. his is the best used example of a 1967 horn center / pad. Rarely do we have more than one center as...
Used aluminum "Mercury Man" head for the center grille medallion. These are just pressed and swedged into the die cast bezel and come out easily with a light tap from behind. Keep in mind these highly amplified pictures make the emblem look much worse than it really is. Do know that the one you...
This emblem was used on the driver side of the 1971 - 1972 Cougar hood and on the passenger side of the trunk lid in 1967 - 1968. Also used on various other Mercury products like the Comet, Cyclone, and Marquis prior to 1973. This will not fit on the fender extension of the 1967- 1968 Cougar....
Grade "A" panel with no blemishes, ready to install on your show car. This listing does not include emblem or the aluminum surround.
These reproductions are fantastic quality! We sent NOS originals to Scott Drake to duplicate and they could not have done a better job. They come with the original type barrel clip fasteners and feature die cast frames with correct pin placement. These emblems are correct in every detail. We are...
Good quality OEM Emblem for the C pillars and RH headlight door of your XR7-G. These are made by the same company that made them originally in 1968! These mount on the lower part of the roof behind the quarter windows. This part of the roof is also known as the 'C' pillar. Click on images to...
Of all of the XR7-G emblems we sell, this one may be the closest to original. This is a nice upgrade for your 1968 Cougar whether it is the standard, decor, XR7 or XR7-G model. The picture above shows the new emblem next to one pulled from a XR7-G parts car.
Individual hash mark for anyone looking to replace a broken or missing hash mark. These are correct only for the 1967 XR-7 but will fit nice on any 1967 - 1970 Cougar and are a nice alternative to the very large aluminum rocker mouldings used in 1968 - 1970 on most models. These are MUCH...
The later run XR7-G emblems we offer are really quite nice, but they are all just a tad smaller than originals. This is almost impossible to detect unless you have a reference point. The lock cover does in fact provide a reference point in that if you use a new emblem you will have a noticeable...
Used on Cougars with no factory Air Conditioning. Located in the top center of the dash, ford engineering number on the backside is D1WB-65042A88.
Here's a good replacement for those old worn out aluminum "stereo" decal inserts for your 69 - 70 door speaker grills. Keep in mind that these are just simple decal stickers and are not made from aluminum as the originals were. We do offer used aluminum decals here.SOLD INDIVIDUALLY. ...
Here's the original "stereo" decal for the 69 - 70 door speaker grills. If you want to keep your car as original as possible, these are for you. These decals are made from aluminum, and as you know, they can get pretty flimsy after 45 years. We'll do our best to pick out good ones for...
Reproduction barrel nut or insert for attaching "Cougar" fender script to the fenders. Each Cougar emblem uses 4 of these barrel nuts which insert into the fender first, and then the Cougar emblem. Additionally, these nuts also go into the C pillars for attaching the XR7 badge or medallion on each...
Regardless of what you have been told these emblems were never chromed. We do not have any of these in stock, probably will not get any more but we post this so as to give you a reference as to what color they should be.
This emblem was used on the driver side of the 1971 - 1972 Cougar hood and on the passenger side of the trunk lid in 1967 - 1968. Also used on various other Mercury products like the Comet, Cyclone, and Marquis prior to 1973. This will not fit on the fender extension of the 1967- 1968 Cougar. Fits...
Used Grade "A" Grille Center Medallion for the 1967 and 1968 Mercury Cougar. These will not have pits or damage to the chrome. Unfortunately the softer black background insert will often times have marks. Ford part # C7WB-8B344-A. Do you want to replace those worn out actuators yourself or are you...
Used grade "A" horn center / pad in light ivy gold / light green for the Mercury Cougar. This is the best used example of a 1967 horn center / pad. Rarely do we have more than one center as nice as this one in stock but we'll do what we can to get you a good pad. This unit includes a reproduction...
This is a very nice reproduction of the 1973 XR7 hood or upper grille emblem. Replaces Mercury part # D3WY-16637-B. Simple to install, this emblem attaches using a clear silicone. Click on images to enlarge. Pictures below show this emblem installed on an original 1973 Cougar hood / grille center...
What a difference a few minor blemishes can make in price! Our grade "B" used centers will always have a few minor dings as shown and maybe some very minor pitting in the painted part but after some clean up they will look almost as good as our grade "A" units when viewed from several feet away....
Very rare find as the vast majority of these XR7-G steering wheel emblems were gold plated. This is very different from the run of the mill used emblems we have all seen with the brass electro plating worn off. I have owned two XR7-G Cougars with this version of emblem installed and others have...
We only get one of these in every couple of years or so. We often have driver quality emblems in stock. This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of 50% of our web price for parts...
Pretty safe to say this item will never be reproduced. We often have used in stock but they are always faded.Ford part number D1WY-8A223-A
Nice reproduction that is "almost" spot on. Of the two versions available this one has much more definition. When you put an original next to this reproduction you will notice the original has a more raised, defined face on the Mercury Man.
Correct anodized aluminum reproduction emblem for 1969-70 quarter panels. These high quality emblems have the black paint applied to the sides just as the originals did. If you want an emblem that better matches your front Cougar script you might want to consider these chrome emblems. You can...
This version of the emblem was actually used on early 70's full-size Mercurys, and is almost identical to the 1969-70 version used on Cougars. In order to use it on a Cougar fuel door, the studs on the back will need to be trimmed down The only visible difference is the thinner / more numerous...
Reproduction passenger side 1967-68 Mercury Cougar "Cougar XR7" dash panel emblem with chrome XR7 highlights. Nice reproduction with locating pins that attach to the woodgrain dash panel on the passenger side of all 1967-68 XR7's (excludes the special edition XR7-G models). The classic Cougar...
Very rare more common version of the XR7-G steering wheel gold plated emblem. This is very different from the run of the mill used emblems we have all seen with the brass electro plating worn off. The burnished version was apparently done first: Ford part number S8WS-3849-A and this...
Restored corral for the passenger side eyelid on the 1969 Mercury Cougar. This is just the outer corral and does not include the background decal or the walking cat emblem. NOTE! If you pay the core charge on our 1969 restored grille parts or complete grilles we will be under the assumption you do...
Used core emblem that will need a new background decal. May have one or two hard to find small pits but will be above average even for a Western car. Make sure you consider our reproduction part before you purchase this. This used unit will be harder to install due to the fact that they were only...
Our used center grill emblems will always have some amount of fade in the plexi area and if the backing has not separated from the rest of the emblem it often times will be lose. We have had good luck filling the backside with epoxy glue. The engineering number as seen from the rear is...
Excellent reproduction of the passenger side 1967-68 Mercury Standard Cougar "Cougar" dash panel emblem. Nice reproduction with locating pins that attach to the padded dash panel on the passenger side of all 1967-68 Standard model Cougars. The factory originally installed these emblems onto the...
Brand new WCCC exclusive! These 1967-only steering wheel center emblems have been needed for some time. Most originals are faded, scratched, and often warped or broken. These new ones fit perfectly in your original center pad and look great. Watch our video below to see how to replace your old...
Rechromed Grille Center Medallion for the 1967 and 1968 Mercury Cougar. Unfortunately the polishing and plating process will take away much of the detail. Cores must be pit free or very close to. Like all of our rechromed parts, if you have exceptionally clean cores and have high standards you...
Assembly required This high quality corral fits perfectly and the chrome plating is well beyond what Ford originally did. The mounting studs are placed in the exact position as original. We have offered the walking cat and black background for sometime now but the challenge has been getting your...
Used cover with dull chrome. This used to be a very sought after and expensive part due to how difficult they were to find. Now that our show quality reproductions are here they have little value... Great for someone that just wants their driver to look complete. Fits all 1967-68 Mercury Cougars,...
Good used condition, hard to find with perfect chrome. Often times there will be some shrinkage in the rubber. We cannot guarantee that we will always have the more obscure colors in stock like aqua. We seldom have black in stock. FYI
Good used fuel door framed insert, without the crest as shown. These in most cases will not include the thin foil backing plate as shown. "A" grade will have minor rust pitting and some dullness on the chrome, overall very good used.Foil backing plate available in reproduction, see related items. ...
Fair used fuel door framed insert, without the crest. These most often will not include the thin foil backing plate as shown. "B" grade will have some rust pitting and some dullness on the bright work, overall fair used. Foil inserts available used in limited quantities.
Reproduction ribbed aluminum foil backing plate for the gas doors on the 1969 and 1970 Mercury Cougar and XR7 models.
Amazing quality that surpasses any NOS or restored emblem you will ever see. This unique emblem was only used on the front fender extension (driver side) of the 1967 and 1968 Cougar. Replaces Ford part number C7WY-16604-A. Here's some info on the measurements for placement: 1. From the bottom of...
Restored emblem / insert for the 69 Cougar center grille. These are sold on an exchange basis, so you must have a good core with both studs intact. The emblem will be without the decal in the center. You can get it here. Ford casting number reads C9WB-8B369-A NOTE! If you pay the core charge on...
Walking cat hood emblem for the 1973 Mercury Cougar. Nice looking reproduction that has been needed for some time. Although these originally came only on Standard (non-XR-7) Cougars, some owners may find this version more attractive than the XR-7 emblem.Easily installed, this item attaches using...
Left is the same as right, one year only emblem at the center top of the door panel. Usually will show a small amount of pitting. Casting number as seen on the back reads D0WB-6520802.
High quality reproduction adhesive emblem for your deck lid. Measures 6.5" wide by 2.35" tall. It has the correct black paint applied to the sides. If you have a 71-73 Cougar this chrome emblem is a much better match to your other emblems even though it is not technically correct. We...
Replica of the coil spring shipping tag that would have been found on factory delivered 1967 - 1973 Cougars and Mustangs.
This is an accurate reproduction of the tie down notice decal that was placed on the rear license plate frame. This was to remind dealers to remove the tie down plates that were used to secure the cars to the transport trains / trucks on their way from the factory to the dealers. Ford wanted to...
Excellent reproduction of the little 1 1/8" wide plastic emblem found on every 1970 - 1974 three spoke steering wheel pad. This emblem can also work on the 1969 - 1973 two spoke steering wheel pad but it is not an exact fit as the two spoke wheel emblem is only 1 1/32" wide. Keep in mind we made...
Self threading speed nut for attaching "COUGAR' scrip emblems to the rear quarter panel of any 68 - 70 Mercury Cougar. Sold individually, 4 needed per emblem. Whereas these work fine, the originals were an acorn style nut and look very different.
Will show at least a small amount of pitting. Casting number as seen on the back reads D0WB-652803-E.
New pair of white and yellow paint sticks for the Mercury or Ford. These units were used by FORD at the assembly plants to mark fender aprons, radiator support, transmission, rear end housing, sheet metal, glass and variety of other parts. It's often little details like this that separate...
This decal goes on the tire jack itself.
Reproduction Detroit Locker Glove Box Decal for the 1967, 1968, 1969, 1970, 1971, 1972 and 1973 Mercury Cougar
Controversy abounds on which shrouds received these and which did not. It is our understanding that no early Cougars came from the factory with this decal installed. This decal first surfaced when Ford had major problems with their flex fans in the early 1970's. We will let you decide if it is...
Reproduction 60000 Mile 6 Month Lube Sticker for the 1967 - 1973 Mercury Cougar / Ford Mustang
This is a reproduction of the original service instruction decal that was located on the side of the air cleaner.Fits the following models:1967 Mercury Cougar1968 Mercury Cougar1969 Mercury Cougar1970 Mercury Cougar1967 Ford Mustang1968 Ford Mustang1969 Ford Mustang1970 Ford Mustang ...
This is a reproduction of the original decal that contains the word "FRONT" that was located on the front of the air cleaner.Fits the following models 1967 Mercury Cougar1968 Mercury Cougar1969 Mercury Cougar1970 Mercury Cougar1971 Mercury Cougar1972 Mercury Cougar1973 Mercury Cougar 1967 Ford...
Reproduction Small Block Engine I.D. Bolt for the 1967 - 1973 Mercury Cougar / 1967 - 1973 Ford MustangSold individually
Save your hard earned money when you buy our reproduction deck lock cover with the new XR7-G emblem already installed! Click on images to enlarge. Check out our video below showing how to easily remove and reinstall your 67-68 trunk latch, lock, and cover plate, and some info on getting a new key...
Original part removed from an Eliminator parts car many years ago. The frame is the same as the 69-70 common fuel door with 2 extra holes drilled, the cat emblem is the same as what is found on a 1970 Standard / Eliminator Cougar center grille. On the units that have a faded background foil, we...
Good used grade B pad with dull trim ring and bad center emblem. Emblem will show discoloration, warping, cracks in the lens and maybe all three! Check out the very first Cougar in our video below! ...
Used grade "A" horn center / pad in red for the Mercury Cougar. This is the best used example of a 1967 horn center / pad. Rarely do we have more than one center as nice as this one in stock so obtaining the color you desire would be a rare treat, but we will try our best to accommodate you. This...
This is the aluminum emblem which mounts on the center of all scuff plates. Features raised script surrounded by "Product Of Ford" like original, adhesive backed and protective coating. Sold individually, two required per car. Replaces Ford part # C8ZZ-6513208-T. Technically this is the version...
Used 2-1/8" plexi center cap emblem was used on standard model Mercury Cougars. You can expect the centers to be a bit faded, the background will have blemishes and all will likely have scratches across the face.The pictures above are a few examples of the quality of what we have left in...
Used 2-1/2" standard center cap emblem. This unit looks the same as the 1969-70 version, but is a larger diameter. Ford part # D1WY-1137-A. *TRIVIA* Applique was the industry name for this item back in 1969-70.
Reproduction mounting bracket / retainer for the XR7G headlight eyelid emblem. The emblem will attach to this bracket with double sided tape or epoxy, whichever you choose. Emblem and 3/8" 10/24 nuts not included.
This decal can be used to overlay your replacement oil filter, so it looks more like a vintage original oil filter. Research indicates that the gold was primarily used on 66 and earlier, as was the red. They then phased the red/gold out and replaced it with the white oil filter printed...
Very rare find. Notice how unlike the reproductions the Mercury Head is fully raised. Ford part number C9WY-8213-A , casting number is C9WB-8B369-A This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in...
Complete assembly minus the cylinder. Only the 68 was marked NOS, the 1967 XR7 just had the COUGAR decal. Click on images to enlarge. ...
Beautiful reproduction truck lock cover with new XR-7 decal. Very true to original, the only noticeable difference being that the corners of the decal are slightly more trimmed than the originals. Check out our video below showing how to easily remove and reinstall your 67-68 trunk latch, lock,...
Restored fuel door framed insert without the background decal or crest, for the 1969 - 1970 Mercury Cougar. Foil backing plate available in reproduction. At the moment there are no reproductions on the walking cat, you can however polish up your old cat and re-use it in this frame. ...
Reproduction gold walking cat emblem / insert for the 1968 XR7G T shift handle. Often times these little emblems are missing from the shift handle because the adhesive has worn out and the emblem has fallen out and gotten lost. While technically for the 68 XR7G, this handle will fit on any 67...
Used / refurbished center cap emblem for the Mercury Cougar with XR7 hubcaps / wheel covers. On the XR7 package, this concave aluminum applique was applied to the center of the hubcap / wheel cover. These are always faded, so we've "restored" a few with Sharpies, as shown in the picture. Believe...
Reproduction Space Save Tire Instructions Decal for the 1968 - 1973 Mercury Cougar / Ford Mustang
This is a replica of the warning tag that came on positive (+) terminal of Autolite batteries when the 1967 - 1972 Cougars and Mustangs were shipped from the factory.
Replica of the Autolite battery Stay-Ful tag advertising that the batteries 'Need water only 3 times a year'.
Engine Code Decal for the 302 with automatic transmission and air conditioning on the 1970 Ford Mustang. Printed with L 6° K272AG.
Engine Code Decal for the 302 with a automatic transmission on the 1970 Ford Mustang. Printed with L 6° K280A.
Ignition coil silver decal stamped with:FAC-12029-A12 VOLTS AUTOLITE OLECUSE WITH EXTERNAL RESISTOR
This is the decal used on the button of the female seatbelt buckle. Each seatbelt uses one of these. Sold as a Pair. Replaces Ford Part #: C8AZ-65611C02-A. Check out our video "All about seat belts" below. ...
Reproduction Autolite Fl - 1 Oil Filter Decal for the 1967 - 1972 Mercury Cougar or Ford Mustang