 |
 Exhaust Manifold Bolts(Click Here for More Information or to Order)
Exhaust Manifold Bolts for the 1967 - 1973 Mercury Cougar
|
|
|
 1967 - 1968 Mercury Cougar Grille Repair Clips - New(Click Here for More Information or to Order) Price:$21.75
These simple little grille repair clips have been needed since these cars were new! Over the years I have seen many home remedies to fix this common problem but none were this clean looking, easy to install and failure proof. Soon we will list the 69-70 Cougar version as well as all the different FoMoCo applications from this era.
|
|
|
 1967 - 1968 Mercury Cougar Accelerator Pedal Mounting Screw - Repro(Click Here for More Information or to Order) Price:$3.50
This is a very specialized screw that you do not want to fail or make do with an incorrect fitting or stripped screw. When removing your old screw you will...
|
|
|
 1967 - 1970 Mercury Cougar Seat Track Retaining Nuts - Repro(Click Here for More Information or to Order) Price:$7.00
Sold in a set of four, these are just like originals.
|
|
|
 1967 - 1973 Mercury Cougar Seat Belt Bolts, Complete Set - Used(Click Here for More Information or to Order) Price:$45.00
Pictured is a complete set of...
|
|
|
 1967 - 1973 Mercury Cougar Side View Metal Mirror Mounting Kit - Repro (Click Here for More Information or to Order) Price:$3.00
This kit is similar to the original type mounted in every drivers side door.
|
|
|
 1967 - 1973 Mercury Cougar Side View Rubber Mirror Mounting Kit - Repro (Click Here for More Information or to Order) Price:$3.00
If your are missing your factory Riv-Nuts or you are installing a passenger side mirror . . .
|
|
|
 1967 - 1973 Mercury Cougar Door / Trunk Lock Cylinder Retainer Clip - Repro(Click Here for More Information or to Order) Price:$2.00
Replaces Ford Part #C5AZ-6222023. Not used on 1967-78 trunk locks.
|
|
|
 1967 - 1968 Mercury Cougar Headlight Vacuum Actuator Mounting Pin - Repro(Click Here for More Information or to Order) Price:$11.50
This is 100% accurate reproduction down to the captured lock washer and black Zinc coating. The only difference is that these are made from...
|
|
|
 1967 - 1968 Mercury Cougar Headlight Vacuum Actuator Mounting Pin - Used(Click Here for More Information or to Order) Price:$5.00
This is the bolt that often gets destroyed when you try to remove it from the bottom side of the headlight bucket. Our West Coast Cougars come apart a little easier so we often are able to pull them with minimal effort.
Cougar part number C7SZ-13A173-A.
|
|
|
 1970 - 1972 Mercury Cougar Power Window Bezel Clip - Used(Click Here for More Information or to Order) Price:$15.00
Very hard to find clip that fastens the chrome power window switch bezel to the door panel. Two required per bezel.
*NOTE* Early 1970 Models used the 1969 style of bezel and did not use this clip.
|
|
|
 1967 Mercury Cougar Firewall Insulation Fasteners (Pair) - Repro(Click Here for More Information or to Order) Price:$3.50
Special fasteners which hold firewall insulator to the firewall. Made of high-quality plastic. Sold in pairs
|
|
|
 1968 - 1973 Mercury Cougar Firewall Insulation Fasteners - Repro(Click Here for More Information or to Order) Price:$2.00
Sold individually, replaces Ford part # C8ZZ-6501691.
|
|
|
 1967 - 1968 Mercury Cougar Rear Bumper Guard Fastners - Used(Click Here for More Information or to Order) Price:$32.00
These are all the OEM used fasteners used to mount...
|
|
|
 1967 - 1969 Mercury Cougar Battery Hold Down Clamp Kit - Repro(Click Here for More Information or to Order) Price:$11.00
Includes battery clamp and bolts required to mount battery on tray.
|
|
|
 1967 - 1970 Mercury Cougar 67-70 Battery Hold-Down Bolt Kit - Repro(Click Here for More Information or to Order) Price:$5.90
Kit comes complete with J bolts and mounting nuts.
Replaces Ford Part #: D0AZ-10756-K.
|
|
|
 1967 - 1969 Mercury Cougar Battery Hold Down Clamp - Repro(Click Here for More Information or to Order) Price:$5.80
Stamped steel construction with black vinyl coating like the original to prevent corrosion. Replaces Ford part #: C5AZ-10718-A.
|
|
|
 1969 - 1970 Mercury Cougar Vinyl (Plastic) Battery Hold Down Handle - Repro(Click Here for More Information or to Order) Price:$18.00
According to the Master Parts Catalog, Late 69 through mid 70 used these black vinyl battery hold down handles . . .
|
|
|
 1971 - 1973 Mercury Cougar Battery Hold Down Kit - Repro(Click Here for More Information or to Order) Price:$33.00
Sale price: $29.00
Very nice kit at a reasonable price...
|
|
|
 196? - 1970 Fan Clutch To Water Pump Bolts - Used(Click Here for More Information or to Order) Price:$2.75
Measures 3/4" tall with a captured lock washer. These were removed from 1969 and 1970 428 Cobra Jet Fans. More research is needed before we can conclusively post the interchange and application details on these bolts. Would love to hear what you have fount on your original Cougars equipped with a fan clutch.
|
|
|
 1967 - 1968 Mercury Cougar Arm Rest Mounting Clips - Repro(Click Here for More Information or to Order) Price:$0.60
Four per car unless you have a 1968 decor or standard model that has the unique three hole arm rest and then you will need six.
Replaces Ford part #: C7AZ-6224146.
|
|
|
 1967 - 1969 Mercury Cougar Door Data Plate Rivets - Repro(Click Here for More Information or to Order) Price:$5.50
Correct rivets for the data plate located on your driver's side door. If your plate is missing you can obtain a correct reproduction with your unique codes at www.martiauto.com
|
|
|
 1967 - 1970 Mercury Cougar 390 and 428 Alternator Mounting Kit - Repro(Click Here for More Information or to Order) Price:$10.00
Concourse correct mounting hardware. Replaces Ford Part #: C7ZZ-10346-MK.
|
|
|
 1967 - 1968 Mercury Cougar Wiring Clip - Used(Click Here for More Information or to Order) Price:$5.00
This clip is hidden about midway under your console and is used to...
|
|
|
 1967 - 1968 Mercury Cougar Standard Console Wiring Clip - Used (Click Here for More Information or to Order) Price:$9.00
This small detail item is used to hold the...
|
|
|
 1967 - 1968 Mercury Cougar Fender To Cowl Nut Kit - Repro(Click Here for More Information or to Order) Price:$6.50
Sold as a pair. These often become dislodged due to the force required to be applied after they have rusted in place for decades. Located at the bottoms of the fenders.
|
|
|
 1967 Mercury Cougar Headlight Wire Loom Clip - Used(Click Here for More Information or to Order) Price:$1.00
Good used clip used to route the wiring harness along the driver side of the engine compartment.
|
|
|
 1968 - 1970 Mercury Cougar Headlight Vacuum Hose / Wire Loom Holder Clip - Used(Click Here for More Information or to Order) Price:$4.00
This "D" clip is larger than that found on the Mustangs and 1967 Cougar because it not only hung the wiring loom on the driver side of your engine compartment but also the vacuum lines going to the headlight switch.
|
|
|
 1967 - 1973 Mercury Cougar Rear Valance Fastener - Repro(Click Here for More Information or to Order) Price:$3.00
Correct reproduction using special tooling. Plated to prevent rust.
|
|
|
 1967 - 1973 Mercury Cougar Front Windshield / Rear Window Moulding Retainer Clips - Repro(Click Here for More Information or to Order) Price:$0.30
These clips work for both the windshield and rear window stainless steel mouldings. Replaces Ford Part #: C5ZZ-65423A26-B.
|
|
|
 1967 - 1968 Mercury Cougar Heater Box Clip - Repro(Click Here for More Information or to Order) Price:$2.50
Sale price: $2.25
Fully functional, but is different than the original . . .
|
|
|
 1967 - 1973 Mercury Cougar Heater Box Clip - Used(Click Here for More Information or to Order) Price:$1.50
There is a difference between the used and reproduction of this part . . .
|
|
|
 1967 - 1968 Mercury Cougar Deck Lock Housing Mounting Kit - Used(Click Here for More Information or to Order) Price:$18.00
This listing is for two spacers and two mounting nuts with captured washers. These are the four parts needed to mount your deck lock housing to your deck lid (trunk lid).
|
|
|
 1967 - 1973 Mercury Cougar Rocker Moulding Clips(Click Here for More Information or to Order)
|
|
|
 1969 - 1970 Mercury Cougar Deck Lid Moulding Clips - NOS(Click Here for More Information or to Order) Price:$55.00
This is the sub-kit you would have received when you purchased a stainless steel service replacement deck moulding for your 1967 - 1970 Mercury Cougar. The original clips used with a 1967 - 1968 aluminum deck lid moulding would have been similar but would have had a plastic shell surounding the metal clip.
|
|
|
 1967 - 1973 Mercury Cougar Trim / Moulding Screw - Used(Click Here for More Information or to Order) Price:$0.90
This 1/2" tall unique little screw was used on several different trim parts on the early Mercury Cougars. In 1967 - 1968 there were eight per wheel lip moulding, two per fender extension moulding, two per center grille moulding and five per hood lip moulding for a total of 50 screws. In 1969-1973 they were used on the wheel lips mouldings. The 1971 - 1973 hood lip mouldings used the same screw but it was 5/8" tall.
|
|
|
 1969 - 1970 Mercury Cougar Taillight Mounting Stud - Used(Click Here for More Information or to Order) Price:$0.40
These studs attached the taillight housing to the tail panel of a 1969-1970 Cougar. Five used per taillight, 10 required per car.
|
|
|
 1969 - 1970 Mercury Cougar Taillight Mounting Washer - Used(Click Here for More Information or to Order) Price:$0.40
|
|
|
 1969 - 1970 Mercury Cougar Taillight Nuts - Used(Click Here for More Information or to Order) Price:$0.40
These were used to attach the taillight assembly to the tail panel on a 1969 - 1970 Cougar. Five were used per taillight, 10 required in all for one car.
|
|
|
 1967 - 1968 Mercury Cougar Door Sill Plate Screws - Repro(Click Here for More Information or to Order) Price:$4.00
Chrome plated oval head screw to hold sill plates in position.
|
|
|
| Spoiler Mounting Hardware (Click Here for More Information or to Order)
|
|
|
 1967 - 1970 Mercury Cougar Filler Hose Clamps - Repro(Click Here for More Information or to Order) Price:$7.00
Original style wire clamps for retaining the filler hose to the tank standpipe and filler neck.
|
|
|
 1969 - 1970 Mercury Cougar Roofrail Seal Window Clip / Window Guide - Repro(Click Here for More Information or to Order) Price:$3.50
These vinyl coated clips hold the weatherstrip and guide the window when rolling up.
|
|
|
 1967 - 1973 Mercury Cougar Spark Plug Wire Separator Kit - Repro(Click Here for More Information or to Order) Price:$12.00
High-quality ABS plastic. Available in blue, red and OE black.
|
|
|
 1967 - 1972 Mercury Cougar Valve Cover Spark Plug Wire Separator - Repro(Click Here for More Information or to Order) Price:$4.00
Made of heat resistant black nylon. Keeps spark plug wires neat and orderly. Mounts on valve covers.
|
|
