All Products

Restored emblem / insert for the 69 Cougar center grille. These are sold on an exchange basis, so you must have a good core with both studs intact. The emblem will be without the decal in the center. You can get it here. Ford casting number reads C9WB-8B369-A NOTE! If you pay the core charge on our 1969 restored grille parts or complete grilles we will be under the assumption you do not have cores to send in or they are average quality with pits and cracks. If you have really clean cores you...

Complete reproduction emergency / parking brake assembly for the 1969 Mercury Cougar or Ford Mustang. The 1969 model used a T shaped chrome release handle and 1970 used a black plastic T shaped release knob. This version has the chrome handle. There is not a plastic T handle reproduction available. Replaces Ford part # C9ZZ-2780-A.

Reproduction emergency / parking brake assembly for the Mercury Cougar that is sold as a complete assembly. These units do look way better than our used crusty originals, but they will never hold up as well as original FoMoCo!Replaces Ford part # D0ZZ-2780-A

These Big Block motor mounts bolt to your engine block on the top side and to the motor mount (insulator) on the bottom side. These are very correct looking and fitting reproductions, much better than the $95 version you will find in most catalogs. Fits 1967-70 Mercury Cougar and Ford Mustang with 390 or 428CJ engines, will fit passenger side of 427 side oiler engine, driver side will work with modification. Original Ford part numbers C7ZZ-6046-A R.H., C7ZZ-6046-B L.H. 427 number for the left...

Reproduction 390GT Engine Lift Hooks for the 1967 Mercury Cougar and Ford Mustang. Also fit 1966-67 Ford Fairlane and 1967 Shelby GT-500, and 1966-67 Ford / Mercury 428 Police Interceptor engines.Ford number C6OZ-17K004-A.

Factory original part for all 1971 - 1973 Cougar *convertibles. Also correct for 1971 429CJ all body styles. Right hand bracket. Ford part number D1ZZ-6028-A.Does not come with hardware. May have a single or pair of holes on the flat surface. We see them both ways.*Excludes non-convertible models.

Mount to the frame for supporting and mounting the FE 390, 427, and 428CJ engines. Also known as lower engine mounting brackets. For all 1967 - 1970 Cougars with 390 - 427 - 428 engines. Also includes 1967 with 289. Sold in sets. Includes one each: D0ZZ-6028-D & D0ZZ-6029-D engine frame brackets.

Reproduction pair of engine pedestals / frame brackets for the 67 - 70 big block V-8’s. Mounts to the frame for supporting and mounting the big block 390, 427 and 428 engines. Also known as lower engine mounting brackets. Sold as a pair.

Factory original part for all 1971 - 1973 Cougar *convertibles. Also correct for 1971 429CJ all body styles. Left hand bracket. Ford part number D1ZZ-6029-A. May have a single or pair of holes on the flat surface. We see them both ways.*Excludes non-convertible models.

Original 1971 to 1972 hardtop small block or 351 V-8 engine frame brackets. Includes one each: D0OZ-6028-B & D0OZ-6029-B engine frame brackets. These will fit directly into your 1973 Coupe which you can no longer find motor mounts for. Once you place these 71-72 stands in your 73 coupe you can now use the reproduction isolators (motor mounts) commonly available. Does not come with hardware. Also fits 1971-72 Mustang with 302 or 351 engines.*Excludes 1971 - 1972 convertible Cougar and...

Reproduction pair of engine pedestals / frame brackets for the 68 - 70 small block V-8’s. Mounts to the frame for supporting and mounting the small block 289, 302, 351 engines. Also known as lower engine mounting brackets. We recommend this bracket for 1967 Cougars with 289. Sold in sets. *Converting to these mounts on 1967 Cougars with 289 or 1969 – 1970 convertibles with 351 allows the use of reproduction engine mounts.

Factory stock for 1968 – 1970 small block V-8’s. Mounts to the frame for supporting and mounting the small block 289, 302, 351 engines. Also known as lower engine mounting brackets. We recommend this bracket for 1967 Cougars with 289. Sold in sets. Includes one each: D0ZZ-6028-C & D0ZZ-6029-C engine frame brackets. These are better quality and fit than the reproductions. *Converting to these mounts on 1967 Cougars with 289 or 1969 – 1970 convertibles with 351 allows the use of reproduction...

Reproduction pair of engine Frame Stands for the 1971 - 1972 Mercury Cougar or Ford Mustang.Replaces ford part numbers: Driver side D0OZ-6029-B / Passenger side D0OZ-6028-B Does not come with mounting hardware. *Excludes convertible models.

New Dual Transverse Muffler as used on the 67 Cougar with 390. This muffler is an exact match (connection wise) to the factory Ford OEM Transverse muffler that is no longer available. Muffler dimensions: 20" x 11" x 4 1/2" Aluminized SteelSeam Locked like the originalsSlightly increased flow over stock mufflerAuthentic dimensions to OEM mufflersStock dimensions for absolute proper clearances ...

This direct replacement features a larger than stock diameter of 2-1/4 inches for increased performance. This is the H pipe only and is for any 1969 Mercury Cougar or Ford Mustang with stock cast iron exhaust manifolds. These units are manufactured right here in the good old USA from 2-1/4 inch aluminized pipes and made from an original 1969 Cougar and Mustang with the 390 engine. We also sell this H pipe in a 2 inch diameter and have OEM style dual exhaust systems that include the H pipe,...

Factory cast iron exhaust manifold set, both right C6OE-9430-E and left C6OE-9431-F side exhaust manifolds. Same manifold for all 289 and 302 engines for both 1967 and 1968. Random date codes.

C6OE-9431-F Factory original cast iron exhaust manifold for driver side. Ford manifold used on all 1967 and 1968 289/302 engines.

D1ZE-9431-AA or D3AE-9431-AA (for 1973) 351-2V Cleveland factory original cast iron exhaust manifold for driver side. *351C-2V exhaust manifolds only match up to factory 2V intake manifold ports and some aftermarket aluminum cylinder heads, such as one offered by Edelbrock.

D3AE-9431-AA (for 1973) 351-2V Cleveland factory original cast iron exhaust manifold for driver side. Same casting as D1ZE-9431-AA used 1971-72ish.*351C-2V exhaust manifolds only match up to factory 2V intake manifold ports and some aftermarket aluminum cylinder heads, such as one offered by Edelbrock.

C9OE-9431-B 351W factory original cast iron exhaust manifold for driver side. For all 1969 and 1970 Windsor 351's.

If it were not for the dimples in the top of these rolled tip stainless steel reproductions, they would be visually "spot on" from the rear view once installed! Since the dimpled portion is hidden by the rear valance, this makes for a cost effective replacement option or great for that GT-E clone. Sold as a PAIR. Replaces Ford Part #: C7ZZ-5258-C or C9ZZ-5258-C. *NOTE* If anyone would like to share a picture of an original GT-E tip with the correct "drop down" extension that precedes this tip...

NOS A/C expansion valve for Mercury Cougar or Ford Mustang. Great for that concours restoration because it is often little details like this that separate 1st from 2nd place at the show!Ford part # C9ZZ-19849-A

Senses temperature to open and close the expansion chamber and made just like the original.Will work with both R12 and R134 systems.Replaces part #: C7ZZ-19849.

For factory installed A/C on Mercury Cougars and Ford Mustangs. This unit functions great, but when compared to the NOS unit, you will see that it is cosmetically a little bit different. This uses the "O" ring style seals which are not included.Will work with both R12 and R134 systems.

Scott Drake used the original Ford prints to makes these exactly as the originals with heavier gauge steel than the other reproductions we have seen. Unlike the reproductions of the past, these actually fit without the need for modification or the need to jump on the front of the car to install. They are the best braces on the market today by far... Greatly reduces twisting of the chassis. Also strengthens the front end and helps reduce shock tower fatigue and cracking. Also available in Black...

New Old Stock grille center extension / surround for the 1970 Mercury Cougar, in the original box from Ford.Ford part # D0WB-16A678-A.

This kit is what we recommend to fully convert your 1967 Cougar over to LED Plasma exterior lights. Our WCCC brand LED lights are amongst the brightest on the market and have been specifically engineered with the nuances of the Mercury Cougar sequential system in mind. Keep in mind that over the years folks have become accustomed to very BRIGHT tail lights in traffic and the old incandescent bulbs are not only dim, but they take time to fully illuminate and a split second can make all the...

This kit is what we recommend to fully convert your 1968 Cougar over to LED Plasma exterior lights. Our WCCC brand LED lights are amongst the brightest on the market and have been specifically engineered with the nuances of the Mercury Cougar sequential system in mind. Keep in mind that over the years folks have become accustomed to very BRIGHT tail lights in traffic and the old incandescent bulbs are not only dim, but they take time to fully illuminate and a split second can make all the...

Under dash mounted rear speaker controller. This is a used and tested unit that functions flawlessly. Typically this style of fader switch was used with the stereo radios with either AM/FM or the various 8-Track stereos, with added rear speakers. Included is the blue plug and pigtail that goes to the speakers.The pigtail harness is marked D1AB-19A017-BC.

Under dash mounted rear speaker controller. This is a used and tested unit that functions flawlessly. Typically this style of fader switch was used with the stereo radios with either AM/FM or the various 8-Track stereos, with added rear speakers. Included is the blue plug and pigtail that goes to the speakers.This harness is marked D2AA-18972-AB.

D3ZE-8146-AB Original used fan shroud with a 1973 casting number. Should be for all V-8 engines with air conditioning. Good used, this exact 1973 shroud is not reproduced. For some helpful tips on upgrading your Cougar (or Mustang) cooling system, check out our video:

Good quality "concours" shroud that is more durable than the "horse hair" textured originals. Fits the 1967 390 & 428 Mustang, Cougar & Shelby with the factory 23" radiator or our aftermarket 24" radiator. Opening measures about 19-11/16" in diameter. Since this shroud interchanges with the 1967 Shelby GT500 428 PI, good used shrouds are very expensive and hard to find.  If you happen to have an original you would like to sell we would be very interested in hearing from...

This is an excellent reproduction made from the original Ford tooling and features the original Ford logo. This is correct for all the cross flow radiators used in 1971 - 1973 except the 1971 429CJ. Opening measures about 20-1/8" in diameter. Replaces Ford part # D1ZZ-8146. For some helpful tips on upgrading your Cougar (or Mustang) cooling system, check out our video: ...

AMK engine fastener kit for 1971 Mercury Cougar and Ford Mustang with J or C code 429 Cobra Jet engines. This kit claims to have 136 pieces. This kit additionally fits 1970-71 Ford Torino and Mercury Cyclone and other variants with 429CJ engine.Kit typically includes: fasteners to attach air cleaner, carburetor, crank pulley, distributor / points / condenser / vacuum advance, drain plugs, engine tag, exhaust manifolds, fan / fan clutch, fuel pump, shroud, ignition coil and strap, intake...

Complete under hood master fastener kit for the Mercury Cougar. While technically this master kit is for the 1968 Mercury Cougar, it will also work for the 1967 as well.

Our grade "A" fender extensions have no obvious dings, scrapes or warping due to over tightening of studs. Ford part # C7WB-16019-A. Do you have questions about your Cat’s factory pinstriping? This link may help. This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of 50% of our web price for parts delivered in hand or by carrier to our Brooks, Oregon location. If you're not interested...

New Old Stock passenger side fender extension for the 67 - 68 Cougar.  Ford casting number as seen from the back side reads C7WB-16019-A.

New old stock 1969 Mercury Cougar Passenger Side Front Fender Extension Ford part # C9WB-16A168-B, Mercury MPC # C9WY-16018-A. Do you have questions about your Cat's factory pinstriping? This link may help.

New Old Stock 1970 California evaporative system tapered filler neck hose. Soft and pliable, never installed.Ford part number D0DZ-9047-A

"Premium" firewall pad for your 67 - 68 Cougar or Mustang. It's "premium" in the sense that it's more expensive. The main difference between this and the "economy" version is that it has a layer of foil inside, which helps with heat insulation. However, the total thickness is actually a little less than the economy version. This may make it easier to install, along with the included hard plastic clips (unlike the rubber originals). Given the significant difference in price for negligible...

These quality mats are made in the USA by Auto Custom Carpets. They are a good fit with an aggressive grip rubber backing. These are heavy mats that will not easily slip out of place or become "wadded up" under your brake pedal. They will hold their form for many years and do more than just enhance the look of your Cougar, they will provide an extra layer of insulation providing an added barrier for heat and sound. Very nice carpet floor mats that make for an ideal gift for that Cougar lover...

These quality mats are made in the USA by Auto Custom Carpets. They are a good fit with an aggressive grip rubber backing. These are heavy mats that will not easily slip out of place or become "wadded up" under your brake pedal. They will hold their form for many years and do more than just enhance the look of your Cougar, they will provide an extra layer of insulation providing an added barrier for heat and sound. Very nice carpet floor mats that make for an ideal gift for that Cougar lover...

These quality mats are made in the USA by Auto Custom Carpets. They are a good fit with an aggressive grip rubber backing. These are heavy mats that will not easily slip out of place or become "wadded up" under your brake pedal. They will hold their form for many years and do more than just enhance the look of your Cougar, they will provide an extra layer of insulation providing an added barrier for heat and sound. Very nice carpet floor mats that make for an ideal gift for that Cougar lover...

These quality mats are made in the USA by Auto Custom Carpets. They are a good fit with an aggressive grip rubber backing. These are heavy mats that will not easily slip out of place or become "wadded up" under your brake pedal. They will hold their form for many years and do more than just enhance the look of your Cougar, they will provide an extra layer of insulation providing an added barrier for heat and sound. Very nice carpet floor mats that make for an ideal gift for that Cougar lover...

These quality mats are made in the USA by Auto Custom Carpets. They are a good fit with an aggressive grip rubber backing. These are heavy mats that will not easily slip out of place or become "wadded up" under your brake pedal. They will hold their form for many years and do more than just enhance the look of your Cougar, they will provide an extra layer of insulation providing an added barrier for heat and sound. Very nice carpet floor mats that make for an ideal gift for that Cougar lover...

This Cougar Logo is a favorite of any Cougar Fan. The Cougar became so popular that soon after the Cougar was released all Lincoln - Mercury Dealerships used the phrase "The Sign Of The Cat" in their advertising. These quality mats are made in the USA by Auto Custom Carpets. They are a good fit with an aggressive grip rubber backing. These are heavy mats that will not easily slip out of place or become "wadded up" under your brake pedal. They will hold their form for many years and do more...

These quality mats are made in the USA by Auto Custom Carpets. They are a good fit with an aggressive grip rubber backing. These are heavy mats that will not easily slip out of place or become "wadded up" under your brake pedal. They will hold their form for many years and do more than just enhance the look of your Cougar, they will provide an extra layer of insulation providing an added barrier for heat and sound. Very nice carpet floor mats that make for an ideal gift for that Cougar lover...

These quality mats are made in the USA by Auto Custom Carpets. They are a good fit with an aggressive grip rubber backing. These are heavy mats that will not easily slip out of place or become "wadded up" under your brake pedal. They will hold their form for many years and do more than just enhance the look of your Cougar, they will provide an extra layer of insulation providing an added barrier for heat and sound. Very nice carpet floor mats that make for an ideal gift for that Cougar lover...