All Products

This is an exact reproduction of the wiper transmissions that will connect to the wiper motor and the output shafts. It includes correct links and pivots for full range of motion. This is commonly replaced when swapping your cowl panel

Used wire harness with diffusers for the instrument cluster lighting (dash lights) on the Standard or XR7 71 - 73 Mercury Cougar.  NOTE* When using LED ground sensitive bulbs, you must reverse the black and blue w/red stripe wires. Ford part number D1WB-10B898-AA

Used under dash wiring harness fuse block / box (with a chip or two) with wire leads for the Mercury Cougar STANDARD. This is part of the 14401 main under dash wiring harness. The difference between Standard and XR7 is that the Standard block has the pink resistance wire. *Note - The fuse blocks will have a small amount of damage or chips on it, in spite of what is shown in the picture.

Used under dash wiring harness fuse block / box (with a chip or two) with wire leads for the Mercury Cougar XR7. This is part of the 14401 main under dash wiring harness. The difference between the XR7 and Standard box is that the Standard box has the pink resistance wire.  *Note - The fuse blocks will have a small amount of damage or chips on it, in spite of what is shown in the picture.

Used wire harness for the 69 - 70 STANDARD Cougar. This main harness connects to the harness for the convenience lights on the warning light panel in the center of the dash. Used in conjunction with the two convenience light harnesses / sockets found here. The convenience package was offered on Cougars that were non-XR7.

Used headlight // key buzzer harness for the 1970 Mercury Cougar. 

Quality wiring reproduction for Perfect Circle brand of speed controls as found on most 1967-1971 Ford - Mercury - Lincoln automobiles. Main harness with Ford part number 9A840, can be used on a variety of model and years. Harness connects the servo, has grommet for firewall, and connectors under the dash. Jumper wire to the brake pedal.

Used tilt column wiring harness for the 1967 Mercury Cougar. 

This is a good used power wire that passes through the firewall, travels along the passenger side engine compartment and mates the the rectangular power window relay. Fits 1969-70 Mercury Cougars with factory power windows. This is a Grade B harness that has been tested, inspected and repaired as needed. This harness will function properly, but will have some obvious repairs. We also sell a Grade A harness that will look much better for judging.

Good used grade "A" core plastic passenger side bezel that may have had one or more very minor cracks repaired. One or more studs on the back may have been repaired as well. Finish will be poor or non existent but this bezel, unlike many we see will not have noticeable UV damage which makes them very brittle and prone to future damage.Check out our dash bezel repair video: ...

Good used core plastic bezel that has had one or more cracks repaired. Multiple studs on the back side will show repair work. Finish will be poor or non existent.Check out our dash bezel repair video: ...

1967 Mercury Cougar XR7 Instrument Cluster Bezel / Housing Grade A - Used Good used core plastic bezel that has no cracks, no excuses. Finish will be poor or non existent.

Good used core plastic bezel that has no cracks, no excuses. Finish will be poor or non existent. Check out our video on dash removal and restoration:

Reproduction 270 piece interior master fastener kit for the Mercury Cougar that fits both Standard and XR7. *NOTE* If you click on the selections below, they will take you to each of the sub kits that are included in the main fastener kit. In this kit you will receive the following fasteners: Sun Visor Brackets Kick Panels Armrests (front) Seat Back Adjustment Scuff Plates Glove Box Catch Seat Back Scuff Plates Glove Box Latch Ashtray Liner Mirror Bracket (interior) Glove Box Liner Carpet to...

New product! These 1967 XR-7 "hash marks" or "ribs" are being offered as set of 14. Seven of these were used on each side. These are correct only for the 1967 XR-7 but will fit nice on any 1967 - 1970 Cougar and are a nice alternative to the very large aluminum rocker mouldings used in 1968 - 1970 on most models. These are MUCH better quality that what Ford originally put on the Cougar, you will not see any tiny imperfections or casting marks in the chrome plating and no over-spray in the...

Nice reproduction of the chrome bezel on an XR7-G mirror. Often these become so pitted they cannot easily be restored. This is an exact fit, quality replacement.Click on images to enlarge. ...

This direct replacement is the 2 inch Y pipe only with 2-1/4 intermediate pipe outlets and is for any 1971-73 Mercury Cougar or Ford Mustang with stock cast iron exhaust manifolds. These units are manufactured right here in the good old USA from 2 inch aluminized pipes and made from an original 1971 Cougar and Mustang with the 351C 2V engine. We also sell OEM style dual exhaust systems that include the H pipe, mufflers, and tail pipes.*NOTE* Will not fit 1970 351 Cleveland engines. Please...

Used open box 1969 Mercury Cougar model kit from the original AMT Corporation in Troy Michigan, Model #Y 908 200. Box has a tear in it on one side. Advertised 1/25 scale kit reproduced from official factory prints, everything seems to be inside the box, however a few pieces have been dislodged and sitting apart from the attaching ribs. Includes original build instructions and decals. 

Used open box unbuilt 1969 Mercury Cougar XR7 Hardtop model kit from the original AMT Corporation in Troy Michigan, Model #2202. Part of AMT's "swingin sixties" kits, this Cougar can be build stock or custom with Kelsey spoke mags, Weber carbs and Ram tubes, twin exhaust headers and mufflers, custom hood, custom front end with optional filler panel and custom taillights and rear bumper. All pieces still in plastic and connected to attaching ribs, includes original build instructions....

Open box 1/25 scale 1969 Cougar XR7 Street Machines model kit #6533-10E0 from the AMT ERTL company in Dyersville IA. Although the outer seal has been removed, all contents inside the box are unused. The tires are in a sandwich baggie, so someone was definitely in the box at one point. Includes detailed BOSS 429 engine with performance modifications, moveable steering wheel, vinyl tires and clear and plated parts. Decals include hood stripes with claws and a Cougar sunset mural type...

Personally, for the money, I would prefer a good used original copper tubed coil over a cheesy import that uses aluminum. That is because the aluminum is way more prone to corrosion when compared to the copper unit. We only sell used coils that are clean and sealed and do not sell coils that have pest damage or have corrosion from a leaking heater core. Even though we stand behind these used units for 30 days, we still suggest that you pressure test them before installing as we all know what...

This unit is a reproduction concours correct A/C discharge hose for your Cougar or Mustang.This hose is compatible with both 134a and R12 refrigerants.

Regardless of which V-8 engine, C7ZA-19972-E is the correct part number. This hose is approximately 20 inches long. Two different crimped ends, smooth and waffle may be the difference between Dearborn and San Jose or 1967 and 1968. Anyone know?The Ford MPC number is C7AZ-19972-A.

There are 2 manufacturers of these hoses and many places will call them a "concours" hose. Neither manufacturer make an exact replica of the original sight glass hose. The finish of the hose does not match, but the most obvious difference is that the sight glass itself has a hexagon shape instead of a square shape. If you would prefer a good used original, give us a call, we can usually dig one up for you. Remember to remove your coupler between this hose and the dryer, it will be need...

Decent reproduction of the air conditioning sight glass hose for the Mercury Cougar and Ford Mustang. Hose texture is not the same and the sight glass itself is different, but length and fittings are correct. If your sight glass hose is not original or you do not have the 2 piece quick disconnect, you may need to purchase the complete sight glass hose kit. For 100% correct hose, please see our good used sight glass hoses. Includes Sight Glass Hose (Ford Part # D1ZA-19837-A or...

Regardless of which V-8 engine, C8ZA-19835-A or C8ZA-19837-A both can be the correct part number. This hose is approximately 74 inches long. This hose also incorporates the site glass. The Ford MPC # is C8ZA-19835-A or C8ZA-19837-A.

For 1969 Mercury Cougars and Ford Mustangs with the 351W engine. Also 1970 Mercury Cougars and Ford Mustangs with the 351W or 428CJ engine. This is a Pitts manufactured pulley and clutch assembly with a pulley diameter of 6-3/8", a clutch diameter of 5-3/16", and an overall thickness of 1-11/16 inches. Whew, say that 5 times fast!Ford part # C9AA-2981-D.

For 1967-68 Mercury Cougars and Ford Mustangs with the 289 or 302 engine. This is an Eaton manufactured pulley and clutch assembly with a pulley diameter of 6-5/16", a clutch diameter of 6", and an overall thickness of 2-1/16 inches. Ford part # C7AA-2981-F.

For 1971-73 Mercury Cougars and Ford Mustangs with the 351W engine manufactured after 10-26-1970. This is a Pitts manufactured pulley and clutch assembly with a pulley diameter of 6-5/16", a clutch diameter of 5-1/8", and an overall thickness of 1-11/16 inches. Ford part # D1OA-2981-A. May also have part numbers D1OA-2981-AA, D1OA-2981-A1A, D1OA-2981-A1B, D1OA-2981-A2A, and D1OA-2981-A2B.

Used pulley and clutch assembly for Mercury Cougars and Ford Mustangs with the 390 engine. This is an Eaton manufactured pulley and clutch assembly with a pulley diameter of 6-3/4", a clutch diameter of 6", and an overall thickness of 2 inches. Whew, say that 5 times fast!Ford part # C7AA-2981-H.

For 1967-69 Mercury Cougars and Ford Mustangs with the 390 engine. This is an Eaton manufactured pulley and clutch assembly with a pulley diameter of 6-3/4", a clutch diameter of 6", and an overall thickness of 2 inches. Whew, say that 5 times fast!Ford part # C7SA-2981-A.

For 1967 - 1969 Mercury Cougars and Ford Mustangs with the 390 or 428CJ engine. This is a Pitts manufactured pulley and clutch assembly with a pulley diameter of 6-11/16", a clutch diameter of 6", and an overall thickness of 1-5/8 inches. Whew, say that 5 times fast!Ford part # C7AA-2981-J.

For 1969 Mercury Cougars and Ford Mustangs with the 390 or 428CJ engine. This is a Pitts manufactured pulley and clutch. Pulley diameter 6-3/4", clutch diameter 6", and an overall thickness of 2-1/16 inches. Ford part # C9AA-2981-G.

For 1971 Mercury Cougars and Ford Mustangs with the 429CJ engine. This is a Pitts manufactured pulley and clutch assembly with a pulley diameter of 6", a clutch diameter of 6", and an overall thickness of 1-3/8 inches. Whew, say that 5 times fast! Ford Part # C9AA-2981-E.

For 1971 Mercury Cougars and Ford Mustangs with the 429CJ engine. This is a Pitts manufactured pulley and clutch assembly with a pulley diameter of 5-5/16", a clutch diameter of 5-5/16", and an overall thickness of 1-3/8 inches. Ford part # C9AA-2981-E1, may also have part # C9AA-2981-E2.

For 1971 Mercury Cougars and Ford Mustangs with the 429CJ engine. This is a Pitts manufactured pulley and clutch assembly with a pulley diameter of 5-5/16", a clutch diameter of 5-5/16", and an overall thickness of 1-3/8 inches. Whew, say that 5 times fast!Ford Part # D0VA-2981-A.

This is a blemished piece that we're offering at a discount. We received a shipment of these vents with some issues with the chrome finish. The flaws are visible in direct light but probably not noticeable when installed. Fit and function is the same as our premium units. See example photo for a closeup of the imperfect chrome finish.

Grade A used 1968 Mercury Cougar air conditioning chrome bezel, naked as shown. Very minor blemishes, almost insignificant as shown. No extra parts included, spring is available. Does not come with the 1968 only detachable air vent. The 1968 Cougar electrical assembly manual indicates that this is part of C8WA-19C784-A Register and Bezel. (Bright Finish). Ford casting number on reverse of this piece is C8ZA-19C784. Mustang used a shorter bracket, on the reverse you can see the witness line and...

C9ZZ-19B888-A

This is a blemished piece that we're offering at a discount. We received a shipment of these vents with some issues with the chrome finish. The flaws are visible in direct light but probably not noticeable when installed. Fit and function is the same as our premium units. See example photo for a closeup of the imperfect chrome finish.This reproduction A/C vent register with knobs is a perfect fit for your Mercury Cougar or Ford Mustang / Shelby. Includes all three control knobs. *NOTE* Mustang...

Passenger side air conditioning register vent with slight manufacturer blemishes. See photos for details.

Grade A used passenger side air conditioning vent register for 1967 Ford Mustang with standard (non-deluxe) interiors. This one has the factory pebble grain or camera case finish. Very nice used, only have the one available. We also have several Mustang center vents available with the pebble graining.Replaces Ford part number C7ZA-19893. This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store...

This new reproduction is a spot-on replica of the 1967 passenger side AC vent! It differs from 1968 only in that 1968 used a break-away vent that was very prone to failure. This is a fixed, one piece body and will not fall apart. This will be a direct fit to your 1967 and 1968 Ford Mustang with no modification needed. Dealer pricing available. *NOTE* Mustang used the shorter version of this vent than the Cougar did, otherwise they are visually and mechanically the same. Click on images to...

Used actuator for the seat back release on the 1970 Mercury Cougar or Ford Mustang. This item is tested and will be in working condition. Left is the same as right, two required per car. Sold individually.

Used Alternator Adjusting Arm / 429CJ for the 1971 Mercury Cougar / 1971 Ford Mustang 

Application - 1968 - 390-4V and 427-4V, and all 1968 - 1970 428 Cobra Jet engines. This is also referred to as the low mount alternator adjusting bracket. It has the Ford stamped casting number of C8AE-10145-B. Ford part number is C8AZ-10145-B.

Reproduction Group II customizable oval air cleaner with the optional "Walking Cat" for your Mercury Cougar. Good quality reproduction that will go nicely with our Cougar aluminum valve covers. The finish on the black portion is not the same as the crinkle finish on the valve covers but do know the crinkle finish can be added with an aerosol product found from most paint suppliers. If you are using a vented oil filler cap you will need to drill a hole in the base to insert the rubber...

NOS new old stock vacuum motor, for early 1968 air cleaner snorkels. Up until about April 1968, the air cleaner snorkels were vacuum operated for the trap door going to the exhaust heat riser. Tested as working. Fits a wide variety of Ford cars in 1968. Don't forget to save the heavy washer that goes over the shaft from your old assembly. Ford part number C8AZ-9D612-A.