All Products

D0OE-6312-F 1971 429 CJ engines without air conditioning. Double sheave pulley, 6-1/4" and 7.00" in diameter. Ford Master Part number D0OZ-6A312-G.

D0ZE-6312-B Application is 1970 Boss 302 Eliminator with or without power steering. Triple sheave pulley 5-15/16" and dual outer 6-11/16" diameter. Ford Master Part number D0ZZ-6A312-A. Also a four bolt mount to the crankshaft balancer. The reason for a triple sheave pulley on Boss 302 engines is the inclusion of the Thermactor Smog system from the factory. Smog pumps were placed so that they worked off of the outermost pulley groove on a 3 sheave crankshaft pulley. If with power steering the...

Application, 1969 - 1970 390IP / 428CJ & 428SCJ engines without air conditioning. Casting number 80B. 5-1/2" diameter and 7/16" sheave width.

Application, 1969 Boss 302 Eliminators and Ford Mustang. Ford Part #:  C9OZ-3A733-C Casting #: 90B. 6-3/8" diameter and 5/16" sheave width.

This is a 3 bolt Thermactor smog pump pulley with a diameter of 5.49" inches for the Mercury Cougar GT-E with the 427-4V W code engine. C8OE-9C480-A marked on pulley.Ford part # C8OZ-9B447-B.

C9OE-9C480-A 1969 and 1970 428 Cobra Jet (R and Q code engines) smog pump pulley with air conditioning, manual and automatic transmissions. 3 bolt smog pump pulley with a diameter of 5.10" inches. Ford part number C9OZ-9B447-A.

Reproduction passenger side (right hand) quarter panel skin for the Mercury Cougar. These skins are made in America, but are low quality. 1969 and 1970 are not the same dimensions from the factory, the 1970 model year increased the wheel opening to allow for the optional larger tire size offered in 1970. The 1969 wheel opening measures at approximately 29-1/2" while the 1970 unit comes in at approximately 30-1/2". This reproduction measures approximately 29-1/2" at the wheel opening. ...

This plasma cut patch was taken from the complete skin we list. We do this because not only do some customers not want to replace the entire skin, but often our foreign customers do not want to pay freight for an entire panel. Give us an outline if your requirements for a cut are different from what is shown, and often we can accommodate. This is a "patch" cut, which means that vertically it reaches from the bottom of the panel to about 10" up. You can find the full...

Used Western Modine (W/Mo) 24 inch big block radiator. This is for a 1968 Mercury Cougar or Ford Mustang with 289-2V, 302-2V or 302-4V engines and (automatic code W) transmission. Used core radiator for recoring and restoration. Typical Dearborn radiator, only FoMoCo on the top tank. 1968 Mercury Cougar or Ford Mustang. This is the typical radiator installed at the San Jose, California assembly plant. W/Mo embossed on the top of the tank with a date. Dated 67-10 or October...

Used WMo or Western Modine 24 inch small block radiator. This is for a 1968 Mercury Cougar or Ford Mustang with 289-2V, 302-2V, or 302-4V and 3 or 4 speed manual transmission. Used core radiator for recoring and restoration. Typical San Jose installed assembly line radiator. Factory installed manual transmission radiators did not come with the fittings in the bottom tank for transmission cooling.Replaces Ford part number C8ZE-8005

Very clean rust free support with no rust or collision damage. It will come with the lower support but we cannot always provide a perfect one. If this is critical please call so we can check inventory before you order.

1968 Mercury Cougar AM-8 track Motorola manufactured radio. These will work and all wiring plugs will be present. Good working and tested radio, fresh installed 8 track belt, may have minor cosmetic issues from a past life. NOTE* The one radio we have in stock at the moment has working AM, all buttons work, but the 8 track tape will not stay in position and needs fiddling - Call for advice. *NOTE* Does not include brackets or knobs. Ford master part # C7WA-18806-A, Chassis and Escutcheon...

T7SMW 1967 Mercury Cougar AM-8 track Motorola manufactured radio. May or may not work and wiring plugs may be cut. Good radio for reconditioning, often times the face plate is missing or damaged, one or more functions won't play, etc. Ford master part # C7WA-18806-A, Chassis and Escutcheon Assembly. Are you going to install this unit yourself? The first issue of Legendary Cougar Magazine has a great how to article that will help you in your journey to musical bliss. You can get it here! ...

Used functional AM-8 track Motorola manufactured radio. These will work and all wiring plugs will be present. Good working and tested radio, fresh installed 8 track belt, may have minor cosmetic issues from a past life. Ford part # D2ZA-19A242. Are you going to install this unit yourself? The first issue of Legendary Cougar Magazine has a great how to article that will help you in your journey to musical bliss. You can get it here! ...

Mercury Cougar and Ford Mustang AM-8 track Motorola manufactured radio. May or may not work and wiring plugs may be cut. Great radio for reconditioning and often times the 8 track feature only needs a drive belt to work perfectly again. Ford part # C9ZA-19A242. *TRIVIA* The window sticker price for this option in 1969 was $195.60. Are you going to install this unit yourself? The first issue of Legendary Cougar Magazine has a great how to article that will help you in your journey to musical...

Mercury Cougar AM-8 track radio. Motorola manufactured radio. May or may not work and wiring plugs may be cut. Good radio for reconditioning, often times the 8 track feature only needs a drive belt. Note that the "COUGAR" decal can easily be removed to make it look identical to the 1969 Cougar / Mustang unit which had no decal. The shaft lengths for the 69-70 unit are unique to these years. You can get other years to fit but you will find that your knobs do not rest in the same area and will...

Mercury Cougar and Ford Mustang factory AM/FM stereo. Good used working stereo, but the knobs are sold separately. Ford part # D2ZA-19A241. Are you going to install this unit yourself? The first issue of Legendary Cougar Magazine has a great how to article that will help you in your journey to musical bliss. You can get it here! ...

F8TBZ Mercury Cougar and Ford Mustang AM/FM stereo radio. This is a non-working unit that has a good crystal and knobs. All knobs seem to move freely. When you look inside the cooling holes on the top of the case you can see mouse droppings. Good unit to use for a modern upgrade core or good for restoration. Are you going to install this unit yourself? The first issue of Legendary Cougar Magazine has a great how to article that will help you in your journey to musical bliss. You can get...

Used grade A radio pad for the center console of the Mercury Cougar or Ford Mustang. The color will be right and bright and there will be no cracks or warping. This unit will be mint, no excuses! *NOTE* We rarely can provide the color you need due to the very limited supply we have. 

NOTE! When we ship a rear end, we will remove the third member and ship it in a separate box. Some assembly will be required. Housing overall width - 54-1/4 inches flange to flange. Overall width measured from faces of axles, not the tips. All 1967-70 have the same overall width of 59-1/2 inches. This economy version of our 8 inch rear end assembly is perfect for those intending to add rear disc brakes to their car.  Spring perches are 43 inches apart on center. Axle...

Driver side, rear frame rail, from a 1971, 1972, and 1973 Mercury Cougar convertible. The Ford MPC shows a couple of different numbers and exceptions for this item. It may be the presence or absence of the nutserts for the rear sway bar option. If the sway bar nutserts are needed, please contact WCCC for availability. Full length, we cut so that there is some remaining metal on the edges. Ford part number D2WY-7610125-B.* Note - this item has dimensions in excess of 75 inches, and will ship as...

Passenger side, rear frame rail, from a 1971, 1972, and 1973 Mercury Cougar hard top. The Ford MPC shows a couple of different numbers and exceptions for this item. It may be the presence or absence of the nutserts for the rear sway bar option. If the sway bar nutserts are needed, please contact WCCC for availability. Full length, we cut so that there is some remaining metal on the edges. Ford part number D2WY-7610124-B.* Note - this item has dimensions in excess of 75 inches, and will...

This panel was used on all convertible models without retractable rear belts. Please contact us for choice of color, power or manual windows and with or without seat belt re-tractors. It will not show serious UV damage with the "chalky look" and will have no extra holes drilled.

Rear seat bottom or lower cushion from any 1971-72 Mercury Cougar or Ford Mustang convertible. Minimal rust, solid, just needs clean up and upholstery. We usually leave the upholstery on the frame when we ship. Verify that both of your seat belts anchor under the seat. All of 1973 and possibly late 1972 had the retractor portion of the seat belts in the rear interior panels. That seat belt end, would anchor in the panel area.Replaces Ford part number D1ZB-7663120.*Note - Does not fit coupe or...

Rear seat bottom or lower cushion from any 1972-73 Mercury Cougar or Ford Mustang convertible. Minimal rust, solid, just needs clean up and upholstery. We usually leave the upholstery on the frame when we ship. Verify that only two of your seat belts anchor, are under the seat. All of 1973 and possibly late 1972 had the retractor portion of the seat belts in the rear interior panels. That seat belt end, would anchor in the panel area.Replaces Ford part number D3ZB-7663120.*Note - Does not fit...

Good used rear window with no deep scratches (multiple faint scratches and water spots often will be present). Not perfect but the best you could expect to find from a 50 year old plus parts car and will of course be a better fit than repro. For those wanting Grade "A" glass, we recommend calling us so we can discuss with you the glass that we have available as each piece differs. Need a little help identifying some of the markings on your glass? Check out the Guide to Original Date Coded...

Good used rear window with no deep scratches (multiple faint scratches and water spots often will be present). Not perfect but the best you could expect to find from a 50 year old plus parts car and will of course be a better fit than repro. For those wanting Grade "A" glass, we recommend calling us so we can discuss with you the glass that we have available as each piece differs. Need a little help identifying some of the markings on your glass? Check out the Guide to Original Date Coded...

Very good used door glass with no deep scratches (multiple faint scratches and water spots often will be present). Not perfect but the best you could expect to find from a 50 year old plus parts car and will of course be a better fit than repro. Look for the SUN-X logo to determine if your glass is tinted or not. For those wanting Grade "A" glass, we recommend calling us so we can discuss with you the glass that we have available.Need a little help identifying some of the markings on your...

Core regulator assembly or brain box for factory speed control on a early 1967 Mercury Cougar or Ford Mustang. This is the Curtis-Wright regulator assembly. Basic Ford part number is 9D757, research has not turned up the complete Ford number possibly C7ZZ-9D757-A. Core grade, most likely will need servicing or repair. Bare unit, no brackets, wiring or cables. *Note - We do not have the tools or know how to test this unit. 

Core regulator assembly or brain box for factory speed control on a early 1967 Mercury Cougar or Ford Mustang. This is the Perfect Circle regulator assembly. Basic Ford part number is 9D757, research has not turned up the complete Ford number possibly C7VY-9D757-B. Core grade, most likely will need servicing or repair. Bare unit, no brackets, wiring or cables. *Note - We do not have the tools or know how to test this unit. 

Core regulator assembly or brain box for factory speed control on a early 1968-69 Mercury Cougar or Ford Mustang. This is the Perfect Circle regulator assembly. Basic Ford part number is 9D757, research has not turned up the complete Ford number possibly C8VY-9D757-A. Core grade, most likely will need servicing or repair. Bare unit, no brackets, wiring or cables. *Note - We do not have the tools or know how to test this unit. 

New old stock Ford accessory cable trunk popper. Fits late 1967 - 1973 Mercury Cougar and other Ford products. Lever release, complete kit, NOS Ford. Detailed instructions included.  Ford part number C7AZ-62432A00-A. *Note - All 1967, and most 1968 trunk lids will not have a large enough access opening in the under side structure to allow the trunk latch to be inserted. 

Reproduction, non functional "dummy" correct looking rev limiter. Also referred to as an electronic engine governor or RPM limiter. These were used on 1970 428 Cobra Jet engines when the car was equipped with a manual transmission. Replaces Ford part number DOZF-12450-A.

Reproduction, non functional "dummy" correct looking rev limiter. Also referred to as an electronic engine governor or RPM limiter. These were used on 1970 BOSS 302 engines. Replaces Ford part number DOZF-12450-B.Note that Ford used a solid state voltage regulator that uses the same case starting in 1966 that has been found on Trucks, Thunderbirds, Galaxies and other full size cars. These units have been known to have engineering numbers of C6AF-10316-A, C6TF-10316-A, and D2HF-10316-AA...

This is an example of the best grade A set we can come up with. This was a standard set that was converted to deluxe by installing the reproduction chrome buckle bezels. The mounting hardware is sold separate. Keep in mind we have over 200 complete sets of belts for 1967-73 in many colors and conditions. We will also sell individual belts and related parts. NOTE: The seat belts you receive will most likely not have intact tags. Check out our video "All about seat belts" below. ...

This is a 100% complete, functional set taken from multiple 1967 Mercury Cougars. Often it takes 2-3 cars to put together one set, decent driver quality set as the driver side will often show excessive wear and other belts can be rusted or missing. The set has been thoroughly inspected, cleaned and redyed with RIT dye in a boiling vat with vinegar. This set is driver quality and if one looks closely you will probably find a small crack in each of the re-tractor plastic covers, a few dots of...

This is a complete set of Deluxe (chrome bands on buckles) safety belts removed from a 1969 hardtop minus torx bolt hardware. The set consists of two front retractors (they are not side specific) that measure 22" fully extended tip to tip, four lap belts bonded in pairs with the shoulder portion measuring 45" and the lap belt portion measuring 30" total length. The two male rear belts measure 20" and mount next to the rear interior panels and the female buckle side measures 36" fully extended....

The Cougar used a seat riser that was about one inch lower in height compared to the Mustang so as to compensate for the more plush foam and upholstery.

NOS FoMoCo part in the box. This is the rubber bellows also called the vacuum servo on many speed or cruise control units installed on many Ford products in the 1960's. Likely a component of the servo assembly as installed on 1967-69 Mercury Cougar and Ford Mustangs. Likely also could be used on 1965-71 Lincoln, Mercury or Ford cars with factory installed speed control option.Very hard part to find, the rubber deteriorates from the heat generated by the engines on these cars. Please check your...

Beautifully detailed reproduction of the original wheel mounted on the 1965 GT-350. The aluminum center is CNC machined and set into a steel rim that features triple plate high luster chrome. Center cap sold separately. You can find the styled wheel center caps here.Find the lug nuts here.*NOTE* Limited availability on this unit, so give us a call before you order. Please allow 4 to 5 weeks for delivery. ...

Used T shift handle, originally an over the counter Mercury dress-up accessory. The only Cougars that came from the factory with this real wood shifter were the 1970 Eliminator and 1968 XR7-G. The XR7-G used a gold Cougar "Walking Cat" emblem and the 1970 Eliminator used the silver emblem.  NOTE: The chrome center of the handle has been re-chromed. Also, the emblem and wooden handle ends will not be glued together, assembly will be required. Check out our video on rebuilding...

Get a grip with this very rare find! This used original Hurst T handle, or shifter handle, is a one year only unit with no set-screw as found on the 1970 shifter. Ford part # D1OZ-7213-A. Check out our video on rebuilding your shifter below: ...

Mint Condition NOS part for your XR7-G equipped with automatic transmission. Notice the texture or "Fur" on the Cougar. The majority are smooth from the factory. We have no explanation for this variation. Check out our video on rebuilding your shifter below: ...

Very hard to find 69 - 70 Shelby / 68 - 69 Cougar 4 speed shifter knob. These very rarely come up for sale used and when they do they are expensive. Correct for 1968-69 Mercury Cougar XR7 and 1969-70 Ford Shelby Mustang, all with 4 speed manual transmissions. Ford part number C8WY-7113-C. Check out our video on rebuilding your shifter below: ...

NOS Real woodgrain knob for 1968 XR7-G Mercury Cougars with the 4 speed only. One RARE little unit! Ford master part # C8WY-7213-A.*TRIVIA* Only 26 XR7-G's were built with a 4 speed transmission. Check out our video on rebuilding your shifter below: ...

C9ZZ-7210-A

Factory detailing and triple chrome plating distinguish this tubular shift handles from the rest. Cable and T-lever included. American made for quality workmanship. Replaces Ford Part #: C5ZZ-7210-M. Check out the very first Cougar in our video below! ...

This rod is unique to 1970 because it was the first year of the lock out rod. Very hard to come by when you consider there was no 390 option for 1970. Notice this rod features two different part numbers. Adjustable rod that connects the floor shifter to the big block C-6 automatic transmissions. C6 transmissions only, code "U" on your door data plate tag. 428 Cobra Jet engines were the only Cougar engines to receive the C-6 automatic transmission. Shift rod approximately 17-1/2 inches long....