All Products

Quality plexi-glass lens that is ready to install. Just peel off the protective tape and carefully pull your clock apart and replace and reassemble.The originals had a very slight concavity to them and these differ in that they are made from common, flat stock. These are also available already installed in our rebuilt clocks if you would prefer not to have to install the lens yourself.Check out the video below on our new gauge tester: ...

Good used core plastic bezel that has had one or more cracks repaired. Finish will be poor or non existent.Ford part number: C7WF-10841

Good used core plastic bezel that has had one or more cracks or breaks. Finish will be poor or non existent. Ford part number: C8WF-10841

Good original used toggle tip for the 1971 - 1973 Mercury Cougar XR7

These are ready to ship now! Sold in a set of four. Specific to 1967 XR-7.There are three versions of shafts used on the 1967 - 1968 XR7 dash toggle switches and all three feature the same C7WB-13713-B engineering number. There is a 1967 switch with a large shaft, 1968 with smaller shaft and 1968 with a small shaft that has been milled down on two sides. The reason Ford decreased the size of shaft in 1968 was to enlarge the thickness of the plastic on the toggle tips. By decreasing the size of...

The 1968 toggle tips we sell fit very tight at best.  To make them fit you will have to remove every bit of glue residue left from the old tips and you may even have to enlarge the holes in the plastic by boring them out a little with a drill bit.  Do not put excessive force on the shaft as you may damage the switch internally.  We apologize for the fit but once on you will have an attractive durable set of tips in place.  No returns on these although if you happen to...

Good quality OEM Emblem for the C pillars and RH headlight door of your XR7-G. These are made by the same company that made them originally in 1968! These mount on the lower part of the roof behind the quarter windows. This part of the roof is also known as the 'C' pillar. Click on images to enlarge. FOR IMMEDIATE RELEASE .....Famous race driver Dan Gurney wrote the formula for a new type of personalized sports car -- the Cougar XR7-G -- which will be introduced at Lincoln-Mercury dealerships...

These two piece adhesive XR7-G emblems are made by the OEM supplier to Ford. As you compare these to the now obsolete version supplied through Ford back in the day, you will see these are nowhere close to the original version. One may deduct that since we have the lowest advertised price with the most uncomplimentary description that ours are in some way different than the "other guys". Not so... We just have different opinions of what quality does and does not look like. If it's crap, we'll...

Great quality for the money, but you will have a gap showing around the perimeter. When looking at the backside of these XR7-G emblems, you will see the green vinyl backing on the two sided tape. A NOS emblem, (original emblem sold by Ford) will have green paper backing. These are not technically a reproduction as they are made by the OEM supplier. Click on images to enlarge. Notice the gaps when installed on our reproduction deck lock cover. Here are some pictures on the new emblem side by...

Used XR7G fog light switch. These switches are very hard to come by and we never see more than one at a time. Tested and in working condition. Ford part number C8VB-14A695-A

This direct replacement is the 2-1/4 inch Y pipe only and is for any 1970 Mercury Cougar or Ford Mustang with stock cast iron exhaust manifolds. These units are manufactured right here in the good old USA from 2-1/4 inch aluminized pipes and made from an original 1970 Cougar and Mustang  with the 351C 2V engine. We also sell OEM style dual exhaust systems that include the H pipe, mufflers, and tail pipes.*NOTE* Will not fit 351-4V Cleveland engines, or 1971-73 351C engines. Please allow 2...

This direct replacement is the 2 inch Y pipe only with 2-1/4 intermediate pipe outlets and is for any 1969-70 Mercury Cougar or Ford Mustang equipped with the 351W engine with stock cast iron exhaust manifolds. These units are manufactured right here in the good old USA from 2 inch aluminized pipes and made from an original 1971 Cougar and Mustang with the 351W 2V engine. We also sell OEM style dual exhaust systems that include the H pipe, mufflers, and tail pipes.*NOTE* Will not fit 351...

1973 Mercury Cougar and Ford Mustang shifter handle for automatic transmissions with selector button and set screw. Starting in 1973 Ford stopped using the deluxe handles with faux leather and eliminated the dummy button on the right side of the handle. Ford part numbers D3OZ-7213-A and 1973 black plastic push button. Check out our video on rebuilding your shifter below: ...

Used 1967 Ford-Mercury service department air conditioning diagnosis handbook. Includes detailed diagnosis of sight glass, compressor, lines, belts, electrical and refrigerant. Also included are service procedures of various parts of the A/C system.  Issue LM-7832

1969 Cougar XR7 1/43 scale mini trophy model kit. No glue required, simply snap together the pieces and put the car inside the included plastic "trophy case". We haven't seen many of these collectible kits around the web, it's definitely a hard to find example. Previously owned, there's no plastic bag to contain the parts like the usual model kits, everything comes inside the clear plastic case show in the photos. Some pieces have broken away from the attaching ribs, but it looks like...

NOS 1983 Ford manual on how to read and understand vacuum diagrams. Although it's technically made for older cars, it has tons of useful information on how to decode diagrams. Includes sections on vacuum theory and applications, devices, hoses, schematics and system diagnosis. This handy book has information pertaining to how the engine creates vacuum, the carburetor and it's vacuum pressure regulation characteristics as well as air intake, fuel induction, emissions and ignition. As an...

New old stock, NOS, windshield wiper switch for any 1969 Cougar or Mustang. Marked C9ZB-17A553-A on the back. This is the two speed variety, the 1970 switch has a longer shaft than this 1969 version.

Reproduction emblem for the 390 engine designation. Never used on a Cougar, but an attractive emblem for customizing. Measures 3 1/8" x 3/4" and has two mounting studs.Replaces Ford part # C9ZZ-16637-D.

Vacuum switch not included. This control switch lever assembly only, for the vacuum and damper door consists of the two lever assembly for the vacuum and cable actuation of the A/C plenums damper doors on Mercury Cougar and Ford Mustang with integral A/C.Ford part # C7ZZ-19B888-A.

Exact replacement for your original dryer and should be changed anytime the system is recharged. This stainless steel filter element is the life of your system and stops contaminants from clogging the expansion valve. Painted the correct satin black.

New Old Stock A/C drain hose for Mercury Cougars and Ford Mustangs equipped with factory or integral A/C. The best part is that because this is a NOS part, it will fit right the first time and be absolutely correct!Ford part #: C7ZZ-19858-C.

C9ZZ-18A318-A New Old Stock vacuum control motor for factory air conditioning on all 1969-70 Mercury Cougar and Ford Mustang

C9ZZ-18A318-C New Old Stock vacuum control motor for factory air conditioning on all 1969-70 Mercury Cougar and Ford Mustang.Tested and works perfectly. Has attached extension marked C9ZA-18A318-J.

Used air conditioning vent for any 1968 Mercury Cougar or Ford Mustang with factory installed A/C. These are different than the 1967 A/C vents. For 1968 the vents detached from the main housing for safety reasons. These were meant to 'break away' in the event of an accident. These attach to the housing with a spring, spring sold separately. Grade A is in limited quantities and will have very good chrome, there will be some minor blemishes found under close scrutiny. B grade versions also...

This A/C vacuum canister mounts through the passenger side fender apron near the hood hinge. This vacuum reservoir controls, damper doors inside the A/C unit. This unit includes a built in check valve. Used and tested vacuum tank and bracket, also known as the A/C vacuum reservoir. Fits all 1968-70 Mercury Cougars, and is a replacement for 1967's too. We also stock a Grade B version that looks the part, but does not have a working check valve, and will still need a new rubber coating on the...

This A/C vacuum canister mounts to the passenger side shock tower and controls damper doors inside the A/C unit. This unit includes a built in check valve. Used and tested vacuum tank and bracket, also known as the A/C vacuum reservoir. Fits all 1971-73 Mercury Cougar, 1971-73 Ford Mustang, as well as 1970-71 Ford Torino / Fairlane and Mercury Cyclone Montego, 1970-7? Ford Maverick and Mercury Comet.Replaces Ford part # D0DZ-19A566-A.  

Original retainer for the passenger side A/C vent on Mercury Cougars and Ford Mustangs with equipped with factory A/C. Necessary for correctly installing the upper fastener of the vent.Ford part # C7ZA-19A950-A.

This is a blemished piece that we're offering at a discount. We received a shipment of these vents with some issues with the chrome finish. The flaws are visible in direct light but probably not noticeable when installed. Fit and function is the same as our premium units. See example photo for a closeup of the imperfect chrome finish. This new reproduction is a spot-on replica of the 1967 passenger side AC vent! It differs from 1968 only in that 1968 used a break-away vent...

C9ZZ-14A318-A-Used Wire lead for the accessory terminal found optionally on 1969-70 Mercury Cougar and Ford Mustang fuse blocks. Lead comes with factory molded triple female connector for plugging in the various accessories such as 1969 swing away steering column, rear window defogger, speed or cruise control, etc. Wire can be marked with C8OB-14A318-A or C9ZB-14A318-A. NOTE: There are two version of this wire, one is long and the other is short. The shorter version has a smaller gauge wire. ...

Used Wire lead for the accessory terminal found optionally on 71 - 73 Mercury Cougar and Ford Mustang fuse blocks. Lead comes with factory molded triple female connector for plugging in the various accessories such as 1969 swing away steering column, rear window defogger, speed or cruise control, etc. Wire will be marked with D1AB-14A318-AB

1967 Cougar Owners: To view our exploded view interactive diagram of the tilt steering column parts, click here. This is the part of the tilt switch that the turn signal wand screws into. This part is always included when you purchase a new turn signal switch. 1967-69 mechanism has two springs on either side, the 1970-73 mechanism uses just one spring. There is an active thread on the Classic Cougar Community Forum discussing tilt columns and trouble shooting. *NOTE* For tilt column service,...

This adapter is threaded on bottom for PCV valve and 6 degree angled 5/8" nipple on side. Was gold Cadmium plated, not painted. Original Ford part number C7OZ-6A706-A.

C9ZZ-3K505-A Unique for the 1969 Boss 302 Eliminator and Mustang. Flat steel bar stock spacer that positions the power steering pump a measured distance away from the cylinder head.

Adapter tube for connecting the fuel vapor purge tube to the air cleaner base. Can be either blue or black in color.

We will loan you this adhesive / epoxy applicator for 60 days, with a 100% refundable purchase price. Only available to customers that purchase our 3M bonding adhesive. Tool must be returned in undamaged condition with no missing parts within the 60 day time period.Returns past 60 days are subject to a 25% restocking fee. ...

1967 289 smog pump adjusting arm, casting number C6OE-9B452-A. Ford part number C6OZ-9B452-A. Application is most Ford and Mercury cars sold new in California in 1966-67. Mercury Cougar only used this thermactor pump adjusting bracket in 1967.                                          ...

1967 390 smog pump adjusting arm, casting number C7AE-9B452-A. Ford part number C6AZ-9B452-C. Below are some pictures of a 390 with AC and smog. This motor was pulled from a 1967 Thunderbird so there are a few minor differences when compared to a 1967 Mustang or Cougar but the mounting of brackets and belt alignment are the same. Click on images to enlarge.                                       The...

C9AZ-3D600-A Power steering pump adjusting spacer for use without air conditioning. For most 1971 Mercury Cougar or Ford Mustang with 429CJ engines.

Ford called this part a 'sleeve'. Attaches to the lower shifter arm with a hitch pin. Has nice bushing, with correct nut, washer, and pin. The 1967/68 and 1969/73 versions are identical. The C1AA-7353-C sleeve has fine threads, the C9OZ-7353-A has course threads. Fits all 1967-73 Mercury Cougar and Ford Mustang, and we suspect many other Ford vehicles beginning in 1961. This fine thread version is hard to keep in stock, consider the 1969-73 course thread version as an alternative. Check out...

Ford called this part a 'sleeve'. Attaches to the lower shifter arm with a hitch pin. Has nice bushing, with correct nut, washer, and pin. The 1967/68 and 1969/73 versions are identical. The C1AA-7353-C sleeve has fine threads, the C9OZ-7353-A has course threads. Fits all 1967-73 Mercury Cougar and Ford Mustang, and we suspect many other Ford vehicles beginning in 1961. Check out our video on rebuilding your shifter below: ...

Replaces Ford Part # D0WY-14305-C & D0WY-14305-A

7TPF Factory AM radio for any 1967 Galaxie or LTD models. Unknown working condition.

New old stock amp gauge for the 1969 Mercury CougarFord part number C8WY-10850 Check out the video below on our new gauge tester: ...

Correct three part, telescoping, round base antenna. Comes with round ridged base gasket.*Customer Feedback* "Aloha Don, The antenna showed up with the rest of the USPS sent items. Got in here in three days. Point of installation of antenna. Tie a string to the plug side of the antenna assembly when pulling out from fender so that you can use the string to pull the new antenna plug back through the fender and into the car. Thought of that after pulling antenna out. I was able to use a flexible...

Used anti rattle pad for the stone guard on the Mercury Cougar. This unit is for the 1970 Mercury Cougar specifically and will not fit any other year. These pads must be used with the 1970 Cougar front bumper mounting brackets and the brackets can identified with the square cut window for mounting this pad. Our pad is sold individually and two are required per car.

Reproduction pair of anti rattle pad for the stone guard used on the Mercury Cougar. This unit is for the 1970 specifically and will not fit any other year. These pads must be used with the 1970 front bumper mounting brackets and the brackets can identified by the square cut window for mounting this pad. Sold in pairs and two are required per car.

Pressure die cast, with quality chrome sun visor center bracket and rear view mirror mount. Replaces one of the most visible interior parts on a 1967 Mustang or Cougar. Break away style, two piece construction. Beware of cheap single piece imitations that are available as they are unsafe. Keep in mind you will have to give your screw driver some good pressure when installing to make the mirror fit tight. Replaces Ford part # C7ZZ-17690-A.These are manufactured in the USA. ...

Good used arm rest with no cracks, burns or heavy discoloration. No reproductions to this date have been able to correctly match the original in look or feel.