All Available Parts - 1967 Ford Mustang

Fits Standard and XR7

These are the screws that are used to attach the door latch to the door shell on the 67 - 73 Cougar or Mustang. Sold in a set of 6.

Fits Standard and XR7

Fits Standard and XR7

Sold individually. Replaces Ford Part # 388052-S Helpful tip: Door panel clips install sliding toward the rear of the vehicle.

1/4-20x1 inch stud. Sold individually. Found on various years and parts of Cougars. Used for attaching 1967-68 grilles to the headlight buckets. Also as replacement mounting studs for front and rear fender and quarter extensions. Zinc Dichromate (yellow-rainbow)

Replaces Ford Part #: 379670-s

Reproduction Lower Headlight Bucket Loom Clip for the 1967 - 1968 Mercury Cougar - 1967 - 1968 Ford Mustang 

Set includes ten rectangular clips with pop rivets and two incorrect, irregular shaped end clips (Mustang Part). These clips will fit the 68 Cougar, but are actually replicas of the clips for the 67-68 Mustang. Rather than the plastic end clips in this kit, we recommend the metal version that we sell separately. NOTE - We've found that these reproduction clips do not work as well as the originals, you may find it a bit hard to install the rockers onto these clips without having to...

Reproduction Phillips head screw that is used in a variety of applications on the Mercury Cougar or Ford Mustang. This phosphate & oil (gray-black) colored unit features a wide flat head and is used for attaching the stainless roof side weatherstrip rail. However, it has other interior applications as well.  Sold individually.  24 required per car, set of 24 also available. ...

Multiple uses.5/8" from bend to center hole.

Used for multiple applications. 7/8" from bend to center hole.

Bag of 25 reproduction j-nuts for the front fenders on the Mercury Cougar or Ford Mustang.5/8" from bend to center hole.

24 Reproduction Phillips head screws that are used in a variety of applications on the Mercury Cougar or Ford Mustang. This phosphate & oil (gray-black) colored unit features a wide flat head and is used for attaching the stainless roof side weatherstrip rail. However, it has other interior applications as well.  Also sold individually.

Cylinder head bolt for any 1965-73 Ford 260, 289, or 302 engine 1965-73. This is for one short cylinder head bolt only. Shorter of the two head bolts. Sold individually, 10 short and 10 long needed for a complete engine installation. See related items for short, bolt and kit or set of 20 bolts for 260 / 289 / 302 engines. * Note - Does Not fit 351W cylinder heads!

Replaces Ford part # C2DZ-6A529 Sold Individually.

Reproduction water pump bolt for the Mercury Cougar or Ford Mustang equipped with the small block engine. These are zinc (dark silver) plated and sold individually. This bolt is approximately 2-5/8" to the shoulder and an approximate overall length 2-3/4".

NOS water pump bolt for the Mercury Cougar or Ford Mustang. This bolt is approximately 3-1/2" to the shoulder and an overall approximate length of 3-3/4".Replaces part # 376258-S.

Reproduction water pump / timing chain cover for the Mercury Cougar or Ford mustang equipped with the 289 engine. This bolt has an approximate length of 2" to the shoulder and an approximate overall length of 2-1/4".

Ford part #300958-S Sold individually

 Cylinder head bolt for any 1965-73 Ford 260, 289, or 302 engine 1965-73. This is for one long cylinder head bolt only. Longer of the two head bolts. Sold individually, 10 short and 10 long needed for a complete engine installation. See related items for short, bolt and kit or set of 20 bolts for 260 / 289 / 302 engines. * Note - Does Not fit 351W cylinder heads!

This is the shorter version of the top-loader with no "+" on the head. Sold individually

Replaces Ford part # 385664-S

Bolt that attaches engine mount to block. 4 bolts per engine, used on all v8 engines Mercury Cougar and Ford Mustang 1967-68. Sold individually.Ford number 304668-S2

Sold individually Zinc (dark silver)

Sold individually Zinc (dark silver)

Engine oil dipstick as found on most any 1967 Ford with 289 engines (C, A, or K Code). This has the correct small shield as found on 1967 and earlier cars, starting in 1968 this dip stick gained a larger 'bell' shaped shield that went over the dip stick tube. Ford used several different suppliers and there are differences that show up in the finger handle as shown. Top of the shield to the dip stick end is approximately 19.40 inches. The handles appear to have been painted black...

Chromed engine oil dipstick as found on many 1967-69 Ford with 390 engines (S Code), 427-4V (W Code), 428CJ (Q or R Code). Ford used several different suppliers and there are differences that show up in the finger handle as shown. Top of the shield to the dipstick end varys at either 19.25" and approximately 20.25" (full, add, and safe marks are the same). The handles were chromed originally. Ford part # C7OZ-6750-A, Ford casting # C7OE-6750-A.

Painted engine oil dipstick as found on many 1967-69 Ford with 390 engines (S or X Code). Ford used several different suppliers and there are differences that show up in the finger handle as shown. From the top of the shield to the dipstick end varys from either 19.25" to approximately 20.25" (full, add, and safe marks are the same). The handles were painted blue originally. Typically the painted dipsticks were found on the non-GT (6.5 Litre) cars in 1968. Ford part # C7AZ-6750-A, Ford casting...

This 49 state oil filler cap fits valve covers that utilize twist-on oil caps. This cap is a reproduction of the original cap that was found on 1967 models with the S code 390 and 289 engines with dress up kit like found on DGS 1967 Cougars.. This part features a quality chrome finish along with a crisp "FoMoCo" stamping. At its widest point it is 3" in diameter. The total height is 2 1/4" high including the portion that goes into the valve cover.* Trivia - For 289 engines it should have an...

Correct detail. Chrome plated with oval-style FoMoCo script stamped into the top surface of cap. This is a push on cap and requires the type of cap that has a round filler tube protruding from the driver side valve cover. This is the correct Open Emissions oil cap for the finned "G" valve covers we sell.

Correct detail. Chrome plated with rectangle-style FoMoCo script stamped into the top surface of cap. Nipple measures 5/8" diameter. This is the correct Closed Emissions oil cap for the finned "G" valve covers we sell.

Brightens the engine compartment and looks sharp. Fits our big block finned aluminum valve covers (item# 26018) and others with the round push-in style opening. Requires a rubber grommet to fit into the valve cover, which is usually included with new valve covers.Does NOT fit valve covers with the "stovepipe" fitting (like our small block finned aluminum units) or factory valve covers the tabs for twist-on oil caps. This cap is for after market valve covers.

Brightens the engine compartment and looks sharp. Fits aftermarket valve covers only. These require a rubber grommet to fit into the valve cover. Please Note: This oil cap DOES NOT fit the finned "G" valve covers we sale, as they are built to OEM specs.

Reproduction black oil cap for your 67 - 70 Cougar or Mustang, featuring the FoMoCo logo.

Used oil fill cap for 1967 Mercury Cougar or Ford Mustang with 289 engine. This black painted twist on oil cap was found on non-emission cars. Meaning 49 States except for California.*Note - a chromed version was also available with engine dress up kits.

Rechromed, used oil fill cap for 1967 Mercury Cougar or Ford Mustang with 289 or 390 and California emissions. This chromed push on oil cap was used on the DGS package or 390 GT engine dress up kit which included chrome valve covers and air cleaner lid. Identified by the vertical pointing elbow, for attaching a hose to the air cleaner base. Marked FoMoCo on the top inside a rectangle box.*Note - a Black painted version was also available on most 289 engines sold in California.

Smooth painted valve cover without "Powered by Ford" embossed in the metal. Correct on 1967 Mercury Cougar and 1966-67 Ford Mustang with 289 engines. These will be dirty, and scratched. Plan on cleaning thoroughly, doing minor body work, sanding and painting prior to installation.  Ford part # C6AZ-6582-G. *Restoration Tip* "Powered by Ford" valve covers were not generally used until the 1968 model year. These smooth small block valve covers are correct for 1967 cars. Those wanting to...

Used early version short seat belt mounting bolt to mount the front retractor to the inner rocker panel and used in conjunction with a large washer. This is an early version of the the seat belt bolt with faint or no markings on the head, the later versions are longer, and have much more prominent head markings.13/16" hex head, 1-1/8inch bolt with a 3/16 inch shoulder.

Used early version of the long seat belt bolt for the Mercury Cougar or Ford Mustang. This early version has faint markings on the head of the bolt as where the later versions have more prominent markings. 13/16" hex head,  two inch bolt with a 1/2 inch shoulder. Can be either smooth headed or have an "E".

Used on all four 1967 belts for a total of 8 per car. Found to be slightly dished on most examples we see.

Set of 4 screws for mounting the automatic shifter adapter plate on all 1967-68 Mercury Cougars without console. Also fits 1965-68 Ford Mustangs without console. Check out our video on rebuilding your shifter below: ...

Set of 4 new phillips oval head mounting screws with black finish for all 1967-68 Mercury Cougar automatic shifter bezel mounting plates without console and XR7-G bezels. Also fits 1965-68 Ford Mustangs with automatic transmissions and without consoles. Check out our video on rebuilding your shifter below: ...

Bulk pack of 100 oval head phillips screws for door and window crank handles.

New chrome screws for the upper dash pad moulding at the windshield. Seven chromed screws in the kit. Original style of screw with correct sized small Phillips head. Fits 1967-68 Mercury Cougar and Ford Mustang original trim.

Sold individually, three per side, six per car required. These often get destroyed when you go to replace your door window regulator slides. Three of these are used to install the C7ZZ-6523288-A track. Stainless steel.Thread size: 8/32 Check out our handy diagram below to find other '67-'68 door parts you may need. All the item numbers shown can be typed in to the search bar on our site. (Click image to view full size) Not sure where to begin when it comes to replacing your window regulator?...

Sold individually, two per side, four per car required. These often get destroyed when you go to replace your door window regulator slides. Two of these are used to install the C7ZZ-6523288-A track. Check out our handy diagram below to find other '67-'68 door parts you may need. All the item numbers shown can be typed in to the search bar on our site. (Click image to view full size)Not sure where to begin when it comes to replacing your window regulator? Check out our how-to video...

New pan head screws for installing the automatic console shifter bezel. Sold as a set of 4. Used in conjunction with the 3 metal strips to attach the automatic shifter bezel. Correct black pan head Phillips screw. *HINT - The metal strips can be made from any strips of steel, they don't really need the edges folded if you don't cinch them down too tight. Metal strip should be 1-11/16" x 5/8" with a hole in the middle.

Pictured is a complete set of 1967 Hex bolts, spacers and washers. We will make sure they are damage free, rust free, and a complete set removed from the same year of Cougar as yours. There were minor and major changes almost every year so you will want to select the right year. We also have hundreds of used belts and belt sets that we cannot possibly list all of, so give us a shout for details! 

Sold individually, pivot stud for the aluminum power steering pump mounting bracket. fits all applications for small or big block.  Also used on the 1970 Mercury Cougar with 428CJ. Phosphate & Oil (gray-black)

Sold individually Zinc Dichromate (yellow-rainbow)

Four of these bolts are used to secure the isolator portion of the engine mounts to the 289/302/351 blocks. Includes 351W and 351C engines. 5/8" hex head bolt. Sold individually Concours phosphate & Oil (gray-black).

Sold individually Zinc (dark silver)

Stud that screws directly into the 289 exhaust manifold on most 1965-67 Ford 289 engines, including Mercury Cougar and Ford Mustang. Sold individually Zinc (dark silver)

Sold individually Zinc Dichromate (yellow-rainbow)

Sold individually Zinc Dichromate (yellow-rainbow)

This clip holds the speedometer cable gear to the end of the cable. Replaces Ford Part # : C1DZ-17292

Reproduction Radiator Mount Kit for the 1967 - 1968 Mercury Cougar - 1967 - 1968 Ford Mustang 

Reproduction dark zinc starter bolt for the Mercury Cougar or Ford Mustang equipped with the small block engine. These units are sold individually.

Replaces Ford Part # 50828-S Sold individually. Zinc Dichromate (yellow-rainbow)

These little rivets are used to affix the ID tag to the passenger side of the 3 and 4 speed top-loader transmissions. Most tags are held in place by two rivets but on some only two are used from the factory.

AMK engine fastener kit for 1967 Mercury Cougar and 1967 Ford Mustang all with C or A code 289 engines with air conditioning. This kit claims to have 126 pieces.Kit typically includes: fasteners to attach air cleaner, carburetor, crank pulley, distributor / points / condenser / vacuum advance, drain plugs, engine tag, exhaust manifolds, fan / fan clutch, fuel pump, shroud, ignition coil and strap, intake manifold, oil filter adapter, oil pan, starter, timing cover, valve covers, water neck,...

AMK engine fastener kit for 1967 Mercury Cougar / Comet, and Ford Mustang / Fairlane all with S code 390-4V or 390GT engines. This kit claims to have 133 pieces.Kit typically includes: fasteners to attach air cleaner, carburetor, crank pulley, distributor / points / condenser / vacuum advance, drain plugs, engine tag, exhaust manifolds, fan / fan clutch, fuel pump, shroud, ignition coil and strap, intake manifold, oil filter adapter, oil pan, starter, timing cover, valve covers, water neck,...

Sold individually. Zinc Dichromate (yellow-rainbow)

Reproduction Lower Radiator Core Support Loom Clip for the 1967 - 1968 Mercury Cougar / 1967 - 1968 Ford Mustang 

Reproduction Anchor Strap - Tape In for the 1967 - 1973 Mercury Cougar / 1967 - 1973 Ford Mustang

Four needed per car. Ford Part Number: 31498-S

Complete engine mounting kit for the 390 engine with standard exhaust. See list below for included hardware.Click on images to enlarge. ...

New valve cover bolts for all 289-2V, 289-4V, 302-2V, 302-4V, and 351W-2V, and 351W-4V Ford engines. These are the AMK bolts with original style Ford assembly line head markings. Correct 7/16 hex head and split tooth captured washer, sold in sets of 12.*Note - Excludes Boss 302 and 351C engines (see part  number 8317)Replaces Ford part number 373071-S.

Four needed per fan shroud. While not technically correct, some like the black screws over the silver because it better matches the radiator and shroud. Hexwasher Head #14 X 5/8 Tapping Screw Ford Part Number: 31498-S

Reproduction alternator mounting kit for the Mercury Cougar or Ford Mustang equipped with the 390 or 428 engine. Spacer not included, but available.

Alternator bolt and installation kit for 1967 Mercury Cougar and Ford Mustang with 390 engines. Includes spacer and pivot bolt and the other three bolts and washers as shown.

New set of bolts for fastening the transmission inspection cover on all 1967-70 Mercury Cougar, Ford Mustang, and Ford anything with 390, 428CJ, and 352 or any FE style Ford engine. Includes 3 and 4 speed transmissions.

New Bolt kit, for the installation of a water pump on any Ford 352, 390, or 428CJ engine. Fits all 1967-70 Mercury Cougar and Ford Mustang with 390-4V, 390-2V, and 428 Cobra Jet engines.

Set of 4 reproduction torque converter nuts for the Mercury Cougar or Ford Mustang.

Reproduction valve cover bolts for all 390 / 427 / 428 Ford engines.

Reproduction bolts and washers for the C-4 automatic bell housing on any 1967-68 Cougar or Mustang equipped with a 289 / 302 engines and code W automatic transmissions. Bell housing to engine block bolts. Fits most all other Ford small block V-8's from 1965-68.

Reproduction bolts and washers for the C-6 automatic bell housing on any 1967-70 Cougar or Mustang equipped with a 390 / 428 engines and code U automatic transmissions. Bell housing to engine block bolts. Fits most all other Ford big block V-8's from 1966-70.

Four of these bolts are used to secure the isolator portion of the engine mounts to the 289/302/351 blocks. Includes 351W and 351C engines. 5/8" hex head bolt. Sold as a set of 4. Concours phosphate & Oil (gray-black).

Cylinder head bolt for any 1967-70 Ford 390 or 428CJ engine. This is for one short cylinder head bolt only. Shorter of the two head bolts. Sold individually, 10 short and 10 long needed for a complete engine installation. See related items for short, bolt and kit or set of 20 bolts for 390 / 428CJ engines.

Cylinder head bolt for any 1967-70 Ford 390 or 428CJ engine. This is for one long cylinder head bolt only. Longer of the two head bolts. Sold individually, 10 short and 10 long needed for a complete engine installation. See related items for short, bolt and kit or set of 20 bolts for 390 / 428CJ engines.

Cylinder head bolt set for any 1965-73 Ford 260, 289, or 302 engine. 10 short and 10 long, Grade 8 cylinder head bolts. Proper lengths for Ford small block engines. Not for 351W cylinder heads. See related items for individual long or short cylinder head bolts.* Note, excludes 351W cylinder heads.

Cylinder head bolt set for any 1967-70 Ford 390 or 428CJ engine. 10 short and 10 long, Grade 8 cylinder head bolts. Proper lengths for Ford FE engines.  See related items for individual long or short cylinder head bolts.

Replaces Ford Part # 379787-S 3/ 8-24x1 1/2 9/16 Sold individually, 3 used per side. There is one long bolt per side, see item 41138.

Replaces ford Part # 381776-S 3/8-24x2 1/2 9/16 Sold individually, 1 used per side. The other 3 bolts are short, see item 41137.

Reproduction Pitman Arm w/ 1" Sector Shaft Nut EACH for the 1967 Mercury Cougar or Ford Mustang

Reproduction zinc front shock bolt with correct anchor symbol on the head, just like the originals.Sold individually.

Reproduction steering gear or seat belt washer for the Mercury Cougar or Ford Mustang. These units are sold individually.Replaces Ford part # 378580-S.

Factory OEM style clamp for attaching the brake booster vacuum hose to the check valve. Also same clamp for securing the rubber boot to the power steering ram cylinder. Sold individually.

This nut fits onto the strut brace at the front of the car, and not the control arm end. It is the lock nut that goes on after the the bigger strut rod bushing nut.Replaces Ford part # 340460-S

New 3/8-16 nut for the shock tower shock cap. Three nuts used on each cap, 6 total per car. Sold individually.Replaces Ford part number 377706-S7.

Used 3/8-16 x 41/64"  carriage bolt for the shock tower shock cap. Three bolts used on each cap, 6 total per car. Sold individually. *Note - Carriage bolt detail cleaned for the picture, actual part will need a clean up on a wire wheel.Replaces Ford part number 378535-S2.

Correct rivets for use after you have painted your car or installed a new door. No special tools needed for installation. Simply lightly tap the center recessed portion with a small bolt or blunt punch. If your plate is missing you can obtain a correct reproduction with your unique codes at www.martiauto.com. Sold as a pair. Replaces Ford Part #: C5ZZ-6223000-A or 354921-S.

This clip is the same as a door panel clip with the exception that it does not have the foam spacer. This clip was used on the 1968 XR7 overhead console, 1967 - 1968 xr7 and standard model upper and lower console pads, seat back access panels and several other applications. This original clip holds tighter than the reproduction. We recommend using this used clip over our reproduction for applications like the seat back because the reproductions often do not cut it. Ford part number...

This is the speedometer cable clip that connects to the firewall and transmission tunnel. Replaces Ford Part # : 373829

Phosphate & Oil finish. Sold individually. Replaces Ford part #: 378782-S

Reproduction 289 - 302 Alternator Bolt w- Smog for the 1967 - 1969 Mercury Cougar - 1967 - 1969 Ford MustangSold individually 

This is longer of the two with the + on the bolt head.

part# 372821-S

part # 379068-SSold individually