All Available Parts - 1972 Ford Mustang
Products (Click sub-categories above to ONLY display results for that Sub-Category) 401-500 of 2343
Sorted By:
Availability:
Display Options:
Availability: In-Stock Item
Item #: 32500 -
These spacer / washers were used on the rear belts of 1968 - 1973 Cougars. 1968 used two per bolt for a total of eight, 69-71 used one per rear belt for a total of four and 72-73 used one per belt on the inner only as the outer belts had a re-tractor in the rear 72-73. They were red to guide the line workers on placement. Sized like the originals, but do not have the dimples all over. 0.53" ID x 0.88" OD.
Availability: In-Stock Item
Item #: 41154 -
Not 100% correct, but close and functional. In 1967 - 1968 there were eight per wheel lip moulding, two per fender extension moulding, two per center grille moulding and five per hood lip moulding for a total of 50 screws. In 1969 - 1973 they were used on the wheel lips mouldings. The 1971 - 1973 hood lip mouldings used the same screw but it was 5/8" tall. Sold as a box of 100.
Availability: In-Stock Item
Item #: 41238 -
Bolt for installing the front inner and outer bumper brackets to frame rail, and rear bumper brackets to body inside of trunk. Sold individually, 8 per car.
Availability: In-Stock Item
Item #: 27463 -
Original Ford style fasteners used on most all Ford products starting in 1968. Sold in pairs. Zink (dark silver)
Availability: In-Stock Item
Item #: 41306 -
These are the screws that are used to attach the door latch to the door shell on the 67 - 73 Cougar or Mustang. Sold in a set of 6.
Availability: In-Stock Item
Item #: 41359 -
Sold individually. Replaces Ford Part # 388052-S Helpful tip: Door panel clips install sliding toward the rear of the vehicle.
Availability: In-Stock Item
Item #: 41256 -
1/4-20x1 inch stud. Sold individually. Found on various years and parts of Cougars. Used for attaching 1967-68 grilles to the headlight buckets. Also as replacement mounting studs for front and rear fender and quarter extensions. Zinc Dichromate (yellow-rainbow)
Availability: In-Stock Item
Item #: 10745 -
Reproduction Phillips head screw that is used in a variety of applications on the Mercury Cougar or Ford Mustang. This phosphate & oil (gray-black) colored unit features a wide flat head and is used for attaching the stainless roof side weatherstrip rail. However, it has other interior applications as well. Sold individually. 24 required per car, set of 24 also available. ...
Availability: Out of Stock
Item #: 32909 -
24 Reproduction Phillips head screws that are used in a variety of applications on the Mercury Cougar or Ford Mustang. This phosphate & oil (gray-black) colored unit features a wide flat head and is used for attaching the stainless roof side weatherstrip rail. However, it has other interior applications as well. Also sold individually.
Availability: In-Stock Item
Item #: 41037 -
Replaces Ford part # C2DZ-6A529
Sold Individually.
Availability: In-Stock Item
Item #: 41002 -
This is the shorter version of the top-loader with no "+" on the head.
Sold individually
Availability: In-Stock Item
Item #: 41023 -
Replaces Ford part # 385664-S
Availability: In-Stock Item
Item #: 41228 -
Sold individually
Zinc (dark silver)
Availability: In-Stock Item
Item #: 15037 -
Kit includes two brackets and grommets for routing battery cable between starter and solenoid on inner fender. Replaces Ford Part # : C5ZZ-14302-K
Availability: In-Stock Item
Item #: 41245 -
Four of these bolts are used to secure the isolator portion of the engine mounts to the 289/302/351 blocks. Includes 351W and 351C engines. 5/8" hex head bolt. Sold individually Concours phosphate & Oil (gray-black).
Availability: In-Stock Item
Item #: 41229 -
Sold individually
Zinc (dark silver)
Availability: In-Stock Item
Item #: 41239 -
Sold individually
Zinc (dark silver)
Availability: In-Stock Item
Item #: 14187 -
This clip holds the speedometer cable gear to the end of the cable. Replaces Ford Part # : C1DZ-17292
Availability: In-Stock Item
Item #: 41243 -
Reproduction dark zinc starter bolt for the Mercury Cougar or Ford Mustang equipped with the small block engine. These units are sold individually.
Availability: In-Stock Item
Item #: 41360 -
These little rivets are used to affix the ID tag to the passenger side of the 3 and 4 speed top-loader transmissions. Most tags are held in place by two rivets but on some only two are used from the factory.
Availability: In-Stock Item
Item #: 41244 -
Sold individually.
Zinc Dichromate (yellow-rainbow)
Availability: Out of Stock
Item #: 41416 -
Reproduction Anchor Strap - Tape In for the 1967 - 1973 Mercury Cougar / 1967 - 1973 Ford Mustang
Availability: In-Stock Item
Item #: 41166 -
Complete engine mounting kit for the 390 engine with standard exhaust. See list below for included hardware.Click on images to enlarge. ...
Availability: In-Stock Item
Item #: 43841 -
Four needed per fan shroud. Sold individually.Ford Part Number: 383152-S
Availability: In-Stock Item
Item #: 12460 -
Set of 4 reproduction torque converter nuts for the Mercury Cougar or Ford Mustang.
Availability: In-Stock Item
Item #: 31569 -
New Bolt kit, for the installation of a water pump on any Ford 351C or 351 Cleveland engine. Fits all 1970-74 Mercury Cougar and Ford Mustang with 351C, 351CJ engines. 11 total pieces in the kit as shown.
Availability: In-Stock Item
Item #: 31566 -
New Bolt kit, for the installation of a water pump on 1970-73 Ford 302, Boss 302, or 351W engine. Fits all 1970 Mercury Cougar and 1970-73 Ford Mustangs. 9 total pieces in the kit as shown.
Availability: In-Stock Item
Item #: 32159 -
Four of these bolts are used to secure the isolator portion of the engine mounts to the 289/302/351 blocks. Includes 351W and 351C engines. 5/8" hex head bolt. Sold as a set of 4. Concours phosphate & Oil (gray-black).
Availability: In-Stock Item
Item #: 33406 -
Cylinder head bolt set for any 1965-73 Ford 260, 289, or 302 engine. 10 short and 10 long, Grade 8 cylinder head bolts. Proper lengths for Ford small block engines. Not for 351W cylinder heads. See related items for individual long or short cylinder head bolts.* Note, excludes 351W cylinder heads.
Availability: In-Stock Item
Item #: 41362 -
Reproduction steering gear or seat belt washer for the Mercury Cougar or Ford Mustang. These units are sold individually.Replaces Ford part # 378580-S.
Availability: Out of Stock
Item #: 41346 -
Sold as a Pair. Ford Part #: C8AZ-2B296-ACheck out our caliper tips and tricks video below: ...
Availability: In-Stock Item
Item #: 41134 -
Replaces Ford Part # 381985-S Sold individually
Availability: In-Stock Item
Item #: 41271 -
Factory OEM style clamp for attaching the brake booster vacuum hose to the check valve. Also same clamp for securing the rubber boot to the power steering ram cylinder. Sold individually.
Availability: In-Stock Item
Item #: 41132 -
Replaces Ford Part # C8AZ-2B164-A
Sold individually
Availability: In-Stock Item
Item #: 41135 -
These brackets are intended to make sure that the brake pads and the caliper stay in the correct alignment, as well as for anti-rattle. Replaces Ford Part # C8OZ-2B295-A. Sold individuallyCheck out our caliper tips and tricks video below: ...
Availability: In-Stock Item
Item #: 41136 -
Replaces Ford Part # 382713-S Sold individuallyCheck out our caliper tips and tricks video below: ...
Availability: In-Stock Item
Item #: 41130 -
Replaces Ford Part # C8AZ-2066-A
Sold individually
Availability: In-Stock Item
Item #: 41133 -
Reproduction disc brake caliper insulators for a large array of FoMoCo products starting in 1968. 2 are required per caliper, 4 total per vehicle. Sold as a pair. Replaces Ford part # C8AZ-2B299-A.Check out our caliper tips and tricks video below: ...
Availability: In-Stock Item
Item #: 41129 -
Replaces Ford Part # C8AZ-2069-A
Sold individually
Availability: In-Stock Item
Item #: 41131 -
Replaces Ford Part # 43260-S
Sold individually
Availability: In-Stock Item
Item #: 41040 -
This nut fits onto the strut brace at the front of the car, and not the control arm end. It is the lock nut that goes on after the the bigger strut rod bushing nut.Replaces Ford part # 340460-S
Availability: Used / Wrecking Yard Item
Item #: 26513 -
This clip is the same as a door panel clip with the exception that it does not have the foam spacer. This clip was used on the 1968 XR7 overhead console, 1967 - 1968 xr7 and standard model upper and lower console pads, seat back access panels and several other applications. This original clip holds tighter than the reproduction. We recommend using this used clip over our reproduction for applications like the seat back because the reproductions often do not cut it. Ford part number...
Availability: Used / Wrecking Yard Item
Item #: 11-0354 -
Two or three of these clips were needed per door to mount the padded armrest. Three were used per armrest for a total of six, on 1969-70 Cougar and Mustangs. Two used in 1971-73 on standard Cougars. Sold individually.Replaces Ford part # C6AZ-6224146-B.
Availability: Used / Wrecking Yard Item
Item #: 14-1002 -
Used in multiple applications front and rear lap belts. Inner and outer, marked with a letter "B" in at least three known fonts. 1-3/4 inches long, 1/2 inch shoulder, Torx 50 tool for installation and removal.
Availability: Used / Wrecking Yard Item
Item #: 14-1038 -
Two per car, identified with the letter "D" in three known fonts. This bolt was used in conjunction with a chrome spacer / washer that is also marked with the letter "D". 1-1/2 inches long, 1/4 inch shoulder, use a Torx 50 for installation and removal.
Availability: Used / Wrecking Yard Item
Item #: 14-1244 -
Used on inner and outer rear seat belt bolts, four per car in 1970 -1971 and used only on the inner rears in 72 - 73 due to the addition of rear retractors. Used in conjunction with two red washer / spacers, marked with three known font styles of the letter "A". 1-5/16 inches long, Torx 50 is the tool for installing and removing.
Availability: Used / Wrecking Yard Item
Item #: 23774 -
One per side, 1968 does not use the triangle markings. The letter "D" stamping was in place to aid line workers with correct placement on the car.
Availability: Used / Wrecking Yard Item
Item #: 23783 -
Often you will see minor irregularities in these washers. These would be considered "blems". Two required per car, used only on the re-tractors.
Availability: In-Stock Item
Item #: 41140 -
Replaces Ford Part # 382626-S
Sold individually
Availability: In-Stock Item
Item #: 13066 -
Two or three of these clips were needed per door to mount the padded armrest. Three were used per car for a total of six, on 1969-70 Cougar and Mustangs. Two used in 1971-73 on standard Cougars. Sold individually.Replaces Ford part # C6AZ-6224146-B.
Availability: In-Stock Item
Item #: 31193 -
Reproduction shoulder belt bolt spacer for the 69 - 73 Cougar or Mustang. Does not have markings like the originals. One per side, two per car.
Availability: Used / Wrecking Yard Item
Item #: 11-0459 -
Used single bolt for attaching door and quarter window regulators on any 1969-73 Mercury Cougar or Ford Mustang or Ford anything most likely. Sold individually
Availability: In-Stock Item
Item #: 31883 -
New single bolt for attaching door and quarter window regulators on any 1969-73 Mercury Cougar or Ford Mustang or Ford anything most likely. AMK part. Sold individually
Availability: In-Stock Item
Item #: 33532 -
Reproduction bolts and washers for the shoulder belts on any 1969-73 Mercury Cougar or Ford Mustang. Includes 2 each of the "D" bolts and chrome thick washers. Quality AMK kit F-3563.
Availability: In-Stock Item
Item #: 33533 -
AMK seat belt washer B-13023. 0.46" ID x 1.25" OD zinc flat washer. Sized so that it rides on the shoulder of the seat belt bolts. It allows the retractor to rotate freely between this washer and the head of the seat belt bolt on 1969-73 cars. Two required per car, used only on the re-tractors.
Availability: Rare / NOS Part
Item #: 15542 -
Phosphate & Oil finish. Sold individually. Replaces Ford part #: 378782-S
Availability: In-Stock Item
Item #: 41004 -
This is longer of the two with the + on the bolt head.
Availability: Rare / NOS Part
Item #: 41024 -
Availability: In-Stock Item
Item #: 41025 -
Ford manual transmission flywheel and automatic transmission flex plate mounting bolts. 6 bolts required, sold individually. Replaces Ford part # 378172-S
Availability: In-Stock Item
Item #: 41038 -
Replaces Ford part # 55806-S
Availability: In-Stock Item
Item #: 41008 -
Availability: In-Stock Item
Item #: 41046 -
Used on all small block engines to attach the timing pointer to the timing cover. 1967 - 1973 V-8 engines 289, 302, & 351.
Availability: In-Stock Item
Item #: 41014 -
Reproduction AC Compressor Clutch Bolt for the 1967 - 1973 Mercury Cougar - 1967 - 1973 Ford MustangSold individually
Availability: In-Stock Item
Item #: 41007 -
Reproduction 351W Intake Manifold Bolt for the 1969 - 1973 Mercury Cougar - 1969 - 1973 Ford MustangSold individually
Availability: In-Stock Item
Item #: 41032 -
Reproduction Alternator Pulley Nut for the 1967 - 1973 Mercury Cougar - 1967 - 1973 Ford MustangSold individually
Availability: In-Stock Item
Item #: 41029 -
Replaces Ford part # 351089-S
Zinc (dark silver) finish
Sold individually
Availability: Used / Wrecking Yard Item
Item #: 33642 -
Used bolt and washer from a factory installed AC Compressor 1967 - 1973 Mercury Cougar - 1967 - 1973 Ford Mustang. Attaches clutch to compressor shaft.
Availability: Rare / NOS Part
Item #: 26817 -
Replaces Part # C9OB-3B284. We also have this bolt available in fine thread but only as a used bolt. Four required per car. Sold individually
Availability: In-Stock Item
Item #: 41010 -
part # 370608-S. Used in multiple places on mounting brackets.
Availability: In-Stock Item
Item #: 41031 -
This nut fits onto the strut brace at the front of the car, and not the control arm end.Replaces Ford part # 380517-S
Availability: Rare / NOS Part
Item #: 41012 -
part # 383722-S Pivot bolt for use with the all steel 1970-73 power steering pump mounting bracket. NOS new old stock!
Fits most all Ford 302/351 from 1970-73 with the above described bracket.
Availability: In-Stock Item
Item #: 15524 -
OEM style nut to hold the axle U-bolt to the axle. Fine threaded like originals 7/16-20 grade 5. Will not fit some reproduction U-bolts. Sometimes these are called shock plate bolts. Replaces Ford part # 379244-S
Availability: In-Stock Item
Item #: 26806 -
part# 384114-S100 Sold individually Check out our caliper tips and tricks video below: ...
Availability: In-Stock Item
Item #: 26821 -
Reproduction adjustment cam / bolt for the lower control arms of the Mercury Cougar or Ford Mustang. We also offer this used version as well. These units are sold individually.Ford part # C6OA-3B236-A.
Availability: In-Stock Item
Item #: 41015 -
1/2"-13 x 4 1/2" grade 8 flanged bolt with a phosphate and oil finish. Ford Part # 382486-S.
Availability: In-Stock Item
Item #: 41027 -
replaces Ford part # B-12764
Availability: In-Stock Item
Item #: 41028 -
Replaces Ford part #375381-S Phosphate & Oil Finish
Availability: In-Stock Item
Item #: 41036 -
Fine thread lock nut used in various places on old Fords, including the differential housing, 1967 disc brake assemblies, and more. Replaces Ford part # 34445-S
Availability: In-Stock Item
Item #: 41041 -
Reproduction nut that replaces Ford part # 34033-S. This is the nut that secures the pitman arm to the steering box. Has correct 7/8"-14 threads. Split washer also needed, not included, nut only.
Availability: In-Stock Item
Item #: 41236 -
Sold indiviually
Phosphate & Oil (gay-black)
Availability: In-Stock Item
Item #: 41164 -
Complete engine mounting hardware kit for the 72-73 351C 2-barrel engine. See below for list of included hardware. Click on images to enlarge.
Availability: In-Stock Item
Item #: 41165 -
Complete engine mounting hardware kit for the 72-73 351C 4-barrel engine. See below for list of included hardware. Click on images to enlarge.
Availability: In-Stock Item
Item #: 25897 -
Sold as a pair. Replaces Ford Part # : D0OZ-8052 Check out our video on Radiator and Fan upgrades below:
Availability: In-Stock Item
Item #: 27494 -
New valve cover bolts for all Boss 302, 351C-2V, and 351C-4V Ford engines. These are the AMK bolts with original style Ford assembly line head markings. Correct 7/16 hex head and split tooth captured washer, sold in sets of 16.*Note - Excludes 289/302 and 351W engines (see part number 8316)1/4-20 X 5/8" Hex Head Bolt with Electrolytic Zinc & Wax finishReplaces Ford part number 373071-S.
Availability: In-Stock Item
Item #: 41059 -
Reproduction brake and fuel line clamp kit for Mercury Cougars and Ford mustangs equipped with disc brakes.
Availability: In-Stock Item
Item #: 41060 -
Reproduction brake and fuel line clamp kit for Mercury Cougars and Ford Mustangs equipped with drum brakes.
Availability: Used / Wrecking Yard Item
Item #: 25484 -
Cable length 22.50 inches long. Has clevis and pin on the end for attaching to the throttle pedal assembly. *Note - Used on Cougars prior to 7/10/1972 look at your throttle pedal end.
Availability: Used / Wrecking Yard Item
Item #: 25613 -
Throttle cable for many 1972 and all 1973 Mercury Cougar and Ford Mustang H code 351-2V engines. Cable length 23-3/4 inches long. Uses a green plastic bushing to attach to the throttle pedal. We believe that the MPC is wrong on the length. Our observations are that the 2V cable is longer than the 4V version.Replaces Ford part number D3ZZ-9A758-B.*Note - Used on 1972 Cougars after 7/10/1972 and all 1973 Cougar and Mustangs. Look at your throttle pedal end for verification. I doubt that...
Availability: Used / Wrecking Yard Item
Item #: 25614 -
Throttle cable for many 1972 and all 1973 Mercury Cougar and Ford Mustang Q code 351-4V engines. Cable length 23 inches long. Identified by the blue plastic bushing on the throttle pedal end of the pedal. We believe that the MPC is wrong on the stated length, the 4V cable is shorter than the 2V version.Replaces Ford part number D3ZZ-9A758-C.*Note - Used on 1972 Cougars after 7/10/1972 and all 1973 Cougar and Mustangs. Look at your throttle pedal end for verification. I doubt that...
Availability: In-Stock Item
Item #: 31878 -
Reproduction throttle cable for the Cougar or Mustang equipped with the 351 engine.Cable length 22.50 inches long. *Note - Used on Cougars prior to 7/10/1972 look at your throttle pedal end.
Availability: Out of Stock
Item #: 31879 -
Reproduction throttle cable for the Cougar or Mustang equipped with the 351 engine. Cable length 24 inches long, check your application. There were size differences between the 2V and the 4V engines. Replaces Ford part number D3ZZ-9A758-C. *Note - Used on 1972 Cougars after 7/10/1972 and all 1973 Cougar and Mustangs. Look at your throttle pedal end for verification. I doubt that date, I think it was much earlier, than July 1972. ...
Availability: Used / Wrecking Yard Item
Item #: 20116 -
SBVALVCOVER Ford engine blue painted valve cover with "Powered by Ford" embossed in the metal. Correct on 1968-1971 Mercury Cougar and 1968-73 Ford Mustang with 289/302/351W engines. Ford master parts catalog shows a right and left version of this cover those Service Replacement numbers are D2OZ-6582-C & D2OZ-6582-D. *Note - This cover will not work on a 351 Cleveland engine.
Availability: In-Stock Item
Item #: 41337 -
replaces Ford part # 385161-S
Zinc - Dichromate (yellow - rainbow) finish
Availability: Used / Wrecking Yard Item
Item #: 25485 -
Bracket that mounts to firewall for accelerator shaft. 1971-73 Mercury Cougar and Ford Mustang.
Availability: Used / Wrecking Yard Item
Item #: 20530 -
York compressor for air conditioning systems for Mercury Cougar and Ford Mustang. These should be professionally inspected or rebuilt and our compressors have all been in storage for some time. Shipped without pulleys, clutches, or valves. The York compressor is constructed mostly of aluminum and is lighter than the Tecumseh brand compressor by 10 pounds. The York compressors are less common too, subject to availability. We often see part numbers on the York tag (which does not list a Ford...
Availability: Used / Wrecking Yard Item
Item #: 20529 -
Tecumseh compressor for air conditioning systems for Mercury Cougars and Ford Mustangs. These should be professionally inspected or rebuilt and our compressors have all been in storage for some time. These Tecumseh compressors came with a front oil fill plug up until 1967, thereafter, they have a top fill plug. Top fill is the most common, and likely what you will receive, unless you specify the 1967 style with front fill. These units are shipped without pulleys, clutches, or valves. The...
Availability: Used / Wrecking Yard Item
Item #: 25522 -
For 1972-73 Mercury Cougars and Ford Mustangs with the 351W engine. This is a Pitts manufactured pulley and clutch assembly with a pulley diameter of 6-5/16", a clutch diameter of 5-1/8", and an overall thickness of 1-11/16 inches. Whew boy, say that 5 times fast!Ford part # D2ZA-2981-A. May also have part numbers of D2ZA-2981-A1A, D2ZA-2981-A1B, or D2ZA-2981-A2A.
Availability: In-Stock Item
Item #: 20698 -
Brake line rubber grommets for any 1967-73 Mercury Cougar or Ford Mustang. These are the ones that go through the shock towers for the front brake lines. Drum or disc, all the same. Sold as a PAIR. Ford number 373624-S.
Availability: Used / Wrecking Yard Item
Item #: 14-0078 -
Used bolts, and usually new washers. Convertible kit comes with 4 - "A" bolts, 4 "B" bolts, 10 new washers. Kit fits all 1970-73 Mercury Cougar and Ford Mustang convertibles. Coupes or hard tops would include shoulder belt hardware. We will make sure these original seat belt bolts are damage free and rust free. The gold finish will be degraded. There were minor and major changes almost every year. We also have hundreds of used belts and belt sets that we cannot possibly list all of, so give us...
Availability: Used / Wrecking Yard Item
Item #: 23391 -
384543-S8 Power steering pump adjusting spacer for use without air conditioning. For most 1970 - 1973 Mercury Cougar or Ford Mustang with 351C engines. Spacer dimensions: 7/16" I.D. and 1/2" thick.*Note 1970 and later cars with 302 or 351W engines use a 3/4 inch spacer.