All Available Parts - 1967 Ford Mustang
Products (Click sub-categories above to ONLY display results for that Sub-Category) 501-600 of 3117
Sorted By:
Availability:
Display Options:
Availability: In-Stock Item
Item #: 42035 -
Most times you do not need new hinges but rather new bushings and pins. If your hinges are such that the holes are "hogged out" and no longer seat the bushing firmly then you will need to buy one of our good used hinges that come with new bushings and pin. These overseas hinges are not known for fitting well, we cannot recommend them and we do not accept returns or exchanges on them.Replaces Ford part # C7ZZ-6522810. ...
Availability: In-Stock Item
Item #: 42049 -
Most times you do not need new hinges but rather new bushings and pins. If your hinges are such that the holes are "hogged out" and no longer seat the bushing firmly then you will need to buy one of our good used hinges that come with new bushings and pin. These overseas hinges are not known for fitting well, we cannot recommend them and we do not accept returns or exchanges on them. Replaces Ford part # C7ZZ-6522800-C.
Availability: In-Stock Item
Item #: 42053 -
Most times you do not need new hinges but rather new bushings and pins. If your hinges are such that the holes are "hogged out" and no longer seat the bushing firmly then you will need to buy one of our good used hinges that come with new bushings and pin. These overseas hinges are not known for fitting well, we cannot recommend them and we do not accept returns or exchanges on them. Replaces Ford part #: C7ZZ-6522800-C. ...
Availability: In-Stock Item
Item #: 42065 -
Most times you do not need new hinges but rather new bushings and pins. If your hinges are such that the holes are "hogged out" and no longer seat the bushing firmly then you will need to buy one of our good used hinges that come with new bushings and pins. These overseas hinges are not known for fitting well, we cannot recommend them and we do not accept returns or exchanges on them. Replaces Ford part #: C7ZZ-6522811. ...
Availability: Out of Stock
Item #: 26143 -
Used, with little to no scratches, suitable for every day driver.
Availability: Out of Stock
Item #: 26144 -
Almost identical to the original, tab is a bit longer. *NOTE*1969 Cougar owners do not need this part as it is built in the the chromed plastic, rectangular bezel on the door panel.
Availability: Out of Stock
Item #: 26149 -
Replaces the original Ford part that features a # C7SB-17B732-A casting number. Basically correct for 1967 but works just as well on 1968 mirrors. These nuts are are not 100% correct for a 67 or 68, kind of a mixture of both.Very nice chrome quality at a reasonable price. NOTE: Our mirror nut removal tool works & fits perfectly with the original mirror nuts. However, you will find the tool will NOT fit this reproduction nut properly, it will require that it be filed a...
Availability: Out of Stock
Item #: 41247 -
Reproduction side view mirror screw. These screws are sold individually. Do you have riv-nut questions? Here are riv-nut answers!
Spotlight!
Featured!
Availability: In-Stock Item
Item #: 32134 -
When ordering this item, you do not need to order a key blank, the key is included. If you need more than one key, you don't need to pay for multiple key cutting services, just buy extra blanks and mention it in the comment section of your order. We now have the ability and equipment from an old Lincoln Mercury dealership to cut keys for Fords "by the numbers". Instead of copying a worn key to make yet another key that doesn't fit properly, we can cut keys as they would have come from the...
Availability: In-Stock Item
Item #: 10665 -
We have created all of the components needed to economically install the steel nutsert or Riv-nut for the exterior mirrors that mount to the car doors. Our steel Riv-nut uses a 1/4 inch hole. You will need a 5/32 Allen or hex key, 3/8 inch wrench, and a 7/16 inch wrench. The Riv-nut needs to be assembled on the kit as shown prior to installation.
The assembly is installed flush, in the pre-drilled hole. The Allen wrench and the 7/16 are held stationary, while the 3/8 wrench is used to tighten...
Availability: Used / Wrecking Yard Item
Item #: 11-0267 -
Ford called this small door latch part an adjuster. It threads onto the bottom of the door latch rod inside the door. Common to most Ford products 1965-1970. Ford part number C5AZ-62218106-A.
Availability: Used / Wrecking Yard Item
Item #: 11-0268 -
Used original door latch rod for the interior push button lock on the passenger side (right hand) of the Mercury Cougar or Ford Mustang.Ford part # C7ZZ-6521852-A.
Availability: Used / Wrecking Yard Item
Item #: 11-0269 -
Used original passenger side (right hand) key lock to latch door lock rod for the Mercury Cougar or Ford Mustang.Ford part # C7ZZ-6522134-A.
Availability: Used / Wrecking Yard Item
Item #: 11-0274 -
Used original door latch rod for the interior push button lock on the driver side (left hand) of the Mercury Cougar or Ford Mustang.Ford part # C7ZZ-6521853-A.
Availability: Used / Wrecking Yard Item
Item #: 11-0275 -
Used original driver side (left hand) key lock to latch door lock rod for the Mercury Cougar or Ford Mustang.Ford part # C7ZZ-6522135-A.
Availability: Used / Wrecking Yard Item
Item #: 11-0361 -
Good original passenger side door latch rod set. Includes rod for inside lock, outside key lock, and outside door release actuating rod. These are good used parts and are a better quality and value compared to the reproductions. Only fits passenger side doors of 1967 Mercury Cougar and Ford Mustang. 1967 door latches are unique, they have a short tab for the inside door lock knob typically.
Check out our handy diagram below to find other '67-'68 door parts you may need. All the item numbers...
Availability: Used / Wrecking Yard Item
Item #: 11-0360 -
Good original driver side door latch rod set. Includes rod for inside lock, outside key lock, and outside door release actuating rod. These are good used parts and are a better quality and value compared to the reproductions. Only fits passenger side doors of 1967 Mercury Cougar and Ford Mustang. 1967 door latches are unique, they have a short tab for the inside door lock knob typically.
Check out our handy diagram below to find other '67-'68 door parts you may need. All the item numbers shown...
Availability: In-Stock Item
Item #: 26086 -
Protects door panels from the abrasive action of rotating handles. Made from a very hard nylon type material featuring the correct milky white color. Replaces Ford Part #: C5AZ-6223370-A.
Availability: In-Stock Item
Item #: 26100 -
Protects quarter panels from the abrasive action of rotating handles. Made from a very hard nylon type material featuring the correct milky white color. Replaces Ford Part #: C4SZ-6323370-A.
Availability: In-Stock Item
Item #: 13874 -
Very correct reproduction with a quality chrome finish. The rear (quarter) window cranks are listed in the interior section. Keep in mind their are multiple makers of this part and this is the best. Replaces Ford part # C5ZZ-6523342-C.
Availability: In-Stock Item
Item #: 10252 -
Reproduction driver side (left hand) vent / wing window handle for the Mercury Cougar or Ford Mustang.
Availability: In-Stock Item
Item #: 10251 -
Reproduction passenger side (right hand) vent / wing window handle for the Mercury Cougar or Ford Mustang.
Availability: In-Stock Item
Item #: 13867 -
High quality reproduction. Fits as good as it looks! You can click this image for a magnified view. Replaces Ford Part # C7ZZ-6522600-A or C5ZZ-6522600-C.
Availability: Out of Stock
Item #: 41880 -
These interior door release handles are the only ones on the market from the 4 different manufacturers that are indexed correctly. They are the updated design for 2019 that fits level and the chrome is excellent. All the other versions either tip up or down too far when placed on the splines. These were used on the xr7 model in 1967 and on all Cougar / Mustang models in 1968. The casting number on the back reads C7AB-5422617-A.
Availability: Out of Stock
Item #: 41884 -
These interior door release handles are the only ones on the market from the 4 different manufacturers that are indexed correctly. They are the updated design for 2019 that fits level and the chrome is excellent. All the other versions either tip up or down too far when placed on the splines. These were used on the xr7 model in 1967 and on all Cougar / Mustang models in 1968. The casting number on the back reads C7AB-5422616-A.
Availability: In-Stock Item
Item #: 42026 -
These pressure cast and chrome plated handles are good quality items that are exceptionally low priced. Not show quality or concours correct, but nice replacement. Includes gaskets and hardware. Replaces Ford Part #: C7ZZ-6522404-A and C7ZZ-6522405-A Also Fits: 1967 Ford Mustang 1968 Ford Mustang 1970 Ford Maverick 1971 Ford Maverick 1972 Ford Maverick 1973 Ford Maverick
Availability: In-Stock Item
Item #: 30239 -
Replated original door handles from premium western pit free cores. We sell these on an exchange basis but keep in mind we cannot take pitted cores in exchange. Ford Part #: C7ZZ-6522404-A and C7ZZ-6522405-A
Availability: In-Stock Item
Item #: 23440 -
The High tone is indicated in raised letters located on the perimeter of the horn. The 1971-73 almost uses the same horn and bracket as the 1967-68, but was mounted at a different angle, so if you have a 1971-73 you will need to loosen the screw that holds the horn to the bracket and rotate the horn to the correct position. These horns are close but not actually correct for a Cougar. 1967-68 Cougars used part number C7WF-13802-B Lo / C7WF-13801-B Hi and 1971-73 used D0DF-13802-A Lo /...
Availability: Used / Wrecking Yard Item
Item #: 14729 -
Factory cast iron exhaust manifold set, both right C6OE-9430-E and left C6OE-9431-F side exhaust manifolds. Same manifold for all 289 and 302 engines for both 1967 and 1968. Random date codes.
Availability: Used / Wrecking Yard Item
Item #: 23916 -
PCV TUBE, fits stock GT cast iron manifolds, replaces Ford part number C6AZ-6758-A. The main difference between the 390 tube and the 428 tube is the center fitting angle. The 390 tube has a little less pronounced angle. Fits all 1967-68 S code 390-4V Ford engines. You will need the related fittings for installation. Our used 390 transfer tubes will often times have a dent or ding in the metal tube. The repro is a very top quality alternative, they would be concours correct in appearance. ...
Availability: In-Stock Item
Item #: 15299 -
PCV TUBE, fits stock GT cast iron manifolds, replaces Ford part number C6AZ-6758-A. The main difference between the 390 tube and the 428 tube is the center fitting angle. The 390 tube has a little less pronounced angle. Fits all 1967-68 S code 390-4V Ford engines. You will need the related fittings for installation.
Availability: In-Stock Item
Item #: 41554 -
This fitting screws into intake manifold, has 1/2" nipple for PCV hose, 3/16" vacuum port nipple and threaded hole for smaller accessory fitting. 5/8 by 20 thread pitch
Availability: In-Stock Item
Item #: 10622 -
Water pump gasket for all 289/302/351W/351C/429 engines. This gasket is used between the water pump and water pump plate.
Availability: In-Stock Item
Item #: 10621 -
New water pump gasket for 1967-69 Mercury Cougar and Ford Mustang with 289/302/351W. Single gasket for sealing water pump to water pump plate only.
Availability: In-Stock Item
Item #: 10623 -
New water pump gasket for FE Ford engines. 1967-70 Mercury Cougar and Ford Mustang with 390/427/428CJ engines. Single gasket, two gaskets needed for installing your water pump. Price is for one gasket only.
Availability: In-Stock Item
Item #: 10347 -
Concours bolt for all 1968-70 Mercury Cougar and Ford products including Mustang radiator fan clutch to water pump. Sold individually, or in a set of 4. 1/2 inch hex head size an the threads are 5/16-24. This bolt is approximately 7/8" to the shoulder and 1-1/8" in total length. Replaces Ford part # 380288-S. ...
Availability: In-Stock Item
Item #: 10476 -
Concours bolt set for all 1968-70 Mercury Cougar and Ford products including Mustang radiator fan clutch to water pump. 1/2 inch hex head size. Threads are 5/16-24. Also sold individually. These bolts have an approximate length of 7/8" to the shoulder and an approximate overall length of 1-1/8". ...
Availability: In-Stock Item
Item #: 10323 -
Concours bolt for all 1968-70 Mercury Cougar and Ford products including Mustang, radiator fan clutch to radiator cooling fan. 1/2 inch hex head size. Threads are 5/16-18. One bolt with captured split washer. Also available in a set of 4. ...
Availability: In-Stock Item
Item #: 10477 -
Concours bolt set for all 1968-70 Mercury Cougar and Ford products including Mustang, radiator fan clutch to radiator cooling fan. 1/2 inch hex head size. Threads are 5/16-18. Four bolts with captured split washers. Also sold individually. ...
Availability: In-Stock Item
Item #: 10624 -
New water pump plate gasket for the Mercury Cougar or Ford Mustang.
Availability: In-Stock Item
Item #: 31563 -
This is the Water Pump Bolt Kit for 1967 Mercury Cougar and 1967 Ford Mustang with the 289 engines with air conditioning. Quality kit by AMK Products - F-249. This kit comes with an instruction sheet, and shows the correct placement of the bolts.
Availability: Used / Wrecking Yard Item
Item #: 32671 -
Big block Ford water pump core, suitable for rebuilding. This version has a casting number of C5AE-8505-A, and is dated 5D26 or April 26, 1965. Found on many Ford 390 / 428 / 427 engines from 1965-66. These have casting dates, we list the dates when we have them in stock. Plan on sending it to a vendor that specializes in water pump rebuilding. In all likelihood, the rear cover, heater tube, and impeller will need replacing. See our other core water pump listings for other casting...
Availability: Used / Wrecking Yard Item
Item #: 32935 -
Dated 4G20, July 20, 1964.Big block Ford water pump core, suitable for rebuilding. This version has a casting number of C5AE-8505-A, and is dated 5D26 or April 26, 1965. Found on many Ford 390 / 428 / 427 engines from 1965-66. These have casting dates, we list the dates when we have them in stock. Plan on sending it to a vendor that specializes in water pump rebuilding. In all likelihood, the rear cover, heater tube, and impeller will need replacing. See our other core water pump...
Availability: Used / Wrecking Yard Item
Item #: 32934 -
Dated 6A13, January 13, 1966. Big block Ford water pump core, suitable for rebuilding. This version has a casting number of C5AE-8505-A, and is dated 6A13 or January 13, 1966. Found on many Ford 390 / 428 / 427 engines from 1965-66. These have casting dates, we list the dates when we have them in stock. Plan on sending it to a vendor that specializes in water pump rebuilding. In all likelihood, the rear cover, heater tube, and impeller will need replacing. See our other core water...
Availability: Ships Direct from Supplier (Except International)
Item #: 41521 -
Spot on reproductions made of higher quality steel that OEM!
Availability: Out of Stock
Item #: 31128 -
Used exhaust manifold spacer with butterfly valve for use on 1967 to mid 1968 Mercury Cougar, Mercury Cyclone, Ford Fairlane, and Ford Mustang with 390 or 427-4V engines. Fully functional, we test these with a heat gun, they do open and close. These thermostat control valve assembly mates to the 1967 and 1968 passenger side 390 exhaust manifold up until about Feb 15, 1968. Easy to tell if it is needed with your manifold, no chamfer for the exhaust donuts at collector? you need this or a...
Availability: Ships Direct from Supplier (Except International)
Item #: 32309 -
Reproduction high performance cast iron exhaust manifolds for the 1967 - 1968 Cougar or Mustang equipped with the 289 or 302 engine. Designed to be exactly like the originals, with correct markings and raised part numbers. Includes studs and nuts.Replaces Ford part numbers C6OE-9430-E and C6OE-9431-F
Availability: Used / Wrecking Yard Item
Item #: 32717 -
Used exhaust manifold spacer without butterfly valve for use on 1967 to mid 1968 Mercury Cougar, Mercury Cyclone, Ford Fairlane, and Ford Mustang with 390 or 427-4V engines. Straight factory used spacer. Most cars came equipped with a thermal spacer that often times gets frozen with time. No obstruction with this one.Note - Does not fit the slightly larger 428CJ exhaust manifolds. Ford part number C6OZ-9A427.
Availability: Used / Wrecking Yard Item
Item #: 23814 -
Factory cast aluminum two barrel carburetor spacer plate. Positions carburetor above intake manifold for proper linkage operation. With PCV fitting at rear. Fits all Ford 2 barrel carburetors, bore size is 1-5/8 inches in diameter. ...
Availability: Used / Wrecking Yard Item
Item #: 23928 -
Measures 0.28" thick, with small vacuum hose nipple on rear
Ford Part Number C6AZ-9A589-B. Mint condition original part.
Availability: Used / Wrecking Yard Item
Item #: 23830 -
Factory cast aluminum four barrel carburetor spacer plate, one inch tall. Positions carburetor above intake manifold for proper linkage operation. With PCV fitting at rear. *excludes Boss 302 Eliminator ...
Availability: In-Stock Item
Item #: 41875 -
Good Quality spacer that measures 1 1/8" tall. Comes with PCV hose clamp and vacuum port cap. This was used on all 289, 302, 351w motors with a 4V carburetor.
Availability: In-Stock Item
Item #: 19973 -
New carburetor gasket for all 289-4V, 302-4V, and 351-4V, Mercury and Ford cars from 1964-1970. Same gasket used between intake manifold and spacer, and spacer and carburetor. Sold individually, 2 required for complete installation with Ford 1 inch factory spacer and correct numbered Autolite 4300 carburetors.
Availability: In-Stock Item
Item #: 11811 -
New 390 2BBL Carburetor spacer gasket for the 1968 X code 390-2V engine. Two needed per installation, one on both sides of the spacer plate.
Availability: In-Stock Item
Item #: 19972 -
New carburetor gasket for most 1967-73 2 barrel carburetors. 289/302/351W/351C engines. Replaces Ford Part #: C3AZ-9447-B *Excludes 1968 X code 390-2V premium fuel engines.
Availability: In-Stock Item
Item #: 41464 -
Reproduction 8 Cylinder 2V Choke Thermostat Shield for the 1967 and 1968 Mercury Cougar and Ford Mustang
Availability: In-Stock Item
Item #: 41468 -
Correct black phosphate bolts for use with 289 HiPo (K-code) exhaust manifolds. Although Cougars never offered a HiPo 289, the HiPo manifolds will fit any 67-68 289 or 302.
Availability: In-Stock Item
Item #: 41281 -
Exact Copies Made From the Original Supplier to Ford Motor Co. U.S.A. Made. Ramp-Lok Features a Special Conical Washer Designed Specifically for Exhaust Manifolds.
Availability: In-Stock Item
Item #: 41282 -
Exact Copies Made From the Original Supplier to Ford Motor Co. U.S.A. Made. Ramp-Lok Features a Special Conical Washer Designed Specifically for Exhaust Manifolds. 390 and 427-4V engines without exhaust heat risers. That kit would include a studded bolt for the heat shield. See item 41282.
Availability: In-Stock Item
Item #: 13930 -
Reproduction Exhaust Manifold Pipe Stud Kit for the 260, 289, 302, 351 and 1969 390GT 1967 - 1972 Mercury Cougar and Ford Mustang
Availability: In-Stock Item
Item #: 13793 -
Kit has the longer studs for use with spacers or butterfly spacers, between 390 and 428CJ passenger side exhaust manifolds and H pipe flange.
Availability: In-Stock Item
Item #: 41044 -
Reproduction exhaust pipe to exhaust manifold nut for the Mercury Cougar or Ford Mustang and they are sold individually.Ford part # 376420-S.
Availability: In-Stock Item
Item #: 11802 -
This filter fits all V8 Mercury Cougars or Ford Mustangs with the Autolite Carburetor. This filter fits all 1967 - 1973 Cougars except for the following: the Boss 302 4V, 390 4V, 427 4V, 428 4V and the 429 4V. Will also fit many 6 cyl Mustang applications. These Filters are precisely designed and engineered to meet OEM requirements and fitment. Delivering high efficiency filtration, our filters meet modern engine demands for maximum fuel flow. Prevents harmful contaminants such as dirt,...
Availability: Used / Wrecking Yard Item
Item #: 24024 -
1967 289-4V Autolite 4300 carburetor, Automatic C4 transmission- 49 states. C7DF-AF stamped on the carburetor base, 1.00" venturi size and 470 cfm. Core carburetor with proper numbers, we don't always have the factory Ford Autolite tag that was affixed to the top. PCV spacer plates also available and required for stock air cleaner clearance on top of engine. A code 289-4V engine. *Note not for DSO 52 and DSO 53 California destined cars.
Availability: Used / Wrecking Yard Item
Item #: 33540 -
Dated 5F7 June 7, 1965. Big block Ford water pump core, suitable for rebuilding. This version has a casting number of C5AE-8505-A, and is dated 5F7 or June 7, 1965. Found on many Ford 390 / 428 / 427 engines from 1965-66. These have casting dates, we list the dates when we have them in stock. Plan on sending it to a vendor that specializes in water pump rebuilding. In all likelihood, the rear cover, heater tube, and impeller will need replacing. See our other core water pump listings...
Availability: Used / Wrecking Yard Item
Item #: 24059 -
1967 390-4V Holley 4150 carburetor, automatic C6 transmission - 49 states. C70F-9510-B stamped on the carburetor air horn, Holley list #3794, 600 cfm. Core carburetor with proper numbers, we don't always have the factory Ford Autolite tag that was affixed to the top. S code 390-4V and 390GT engines with automatic transmissions. *Note not for DSO 52 and DSO 53 California destined cars.
Availability: In-Stock Item
Item #: 10481 -
Basic kit for rebuilding your Ford Autolite or Motorcraft square bore 4300 or 4 barrel carburetor. This kit is not for later spreadbore carburetors. Spreadbore carburetors have much larger secondary venturis. See picture.
Availability: In-Stock Item
Item #: 10445 -
Basic kit for rebuilding a 1967-70 Holley model 4150 4 barrel carburetor. Includes illustrated instructions. Holley packaged renew kit. This kit is not for model 4160 or other Holley carburetors. See pictures of Holley 4150 below. Click on images to enlarge. ...
Availability: In-Stock Item
Item #: 10482 -
Basic kit for rebuilding your Ford Autolite or Motorcraft 2100 or 2 barrel carburetor. Covers all factory 2 barrel carburetors on any 1967-73 Mercury Cougar and Ford Mustang with Autolite or Motorcraft 2100 carburetors. Excludes later 2150 carburetors.
Availability: In-Stock Item
Item #: 11231 -
Nice quality reproduction of the bake-o-lite carburetor spacer plate for all 1966-67 S-code 390-4V engines. Measures 0.28" thick, with small vacuum hose nipple on rear replaces Ford Part Number C6AZ-9A589-B. Fits 67 Cougar 390 Fits 67 Mustang 390 Fits 66 Fairlane 390 Fits 67 Fairlane 390 Fits 66 Cyclone 390 Fits 67 Cyclone 390 Check out the very first Cougar in our video below! ...
Availability: Out of Stock
Item #: 24035 -
1967 289-4V Autolite 4300 carburetor, Automatic C4 transmission- California C7DF-D or C7DF-AH stamped on the carburetor base, 1.00" venturi size and 470 cfm. Core carburetor with proper numbers, we don't always have the factory Ford Autolite tag that was affixed to the top. PCV spacer plates also available and required for stock air cleaner clearance on top of engine. A code 289-4V engines with automatic transmissions. *Note - For DSO 52 and DSO 53 California destined cars. ...
Availability: Rare / NOS Part
Item #: 33148 -
This filter ONLY fits the following 1967 - 1973 Cougars: the Boss 302 4V, 390 4V, 427 4V, 428 4V and the 429 4V. Will also fit many Mustang applications. Replaces Ford Part #: C7OZ-9155-A, Filter FG-19.
Availability: Out of Stock, On Order
Item #: 33629 -
This filter fits all V8 Mercury Cougars or Ford Mustangs with the Autolite Carburetor. This filter fits all 1967 - 1973 Cougars except for the following: the Boss 302 4V, 390 4V, 427 4V, 428 4V and the 429 4V. Will also fit many 6 cyl Mustang applications. These Filters are precisely designed and engineered to meet OEM requirements and fitment. Delivering high efficiency filtration, our filters meet modern engine demands for maximum fuel flow. Prevents harmful contaminants such as dirt,...
Availability: In-Stock Item
Item #: 15292 -
New carburetor gasket for 67 - 70 Cougar or Mustang with 390 or 428 cobra jet engines and Ford numbered Holley carburetors. One or two needed per installation (with or without spacer plate) sold individually.
Availability: In-Stock Item
Item #: 14030 -
This is the steel tube that goes from the carburetor to the fuel pump if you have a 289 or 302, and you have the Autolite 4300 4 Barrel Carburetor. Stainless Steel.
Availability: In-Stock Item
Item #: 14029 -
This is the steel tube that goes from the carburetor to the fuel pump. Stainless Steel
Availability: In-Stock Item
Item #: 19904 -
This is the steel tube that goes from the carburetor to the fuel pump.
Availability: In-Stock Item
Item #: 19907 -
This is the steel tube that goes from the carburetor to the fuel pump. OE Steel
Availability: Used / Wrecking Yard Item
Item #: 24058 -
1967 390-4V Holley 4150 carburetor, 3 or 4 speed manual transmission - 49 states. C70F-9510-A stamped on the carburetor air horn, Holley list #3793, 600 cfm. Core carburetor with proper numbers, we don't always have the factory Ford Autolite tag that was affixed to the top. S code 390-4V or 390GT engines manual transmissions.. *Note not for DSO 52 and DSO 53 California destined cars.
Availability: In-Stock Item
Item #: 15260 -
Exact OEM standards and specifications. Correct fiberglass insulation, fittings, rubber hose and S clip.
Availability: In-Stock Item
Item #: 19934 -
Exact OEM standards and specifications. Correct fiberglass insulation, fittings, rubber hose and S clip.
Availability: In-Stock Item
Item #: 15261 -
Exact OEM standards and specifications. Correct fiberglass insulation, fittings, rubber hose and S clip.
Availability: In-Stock Item
Item #: 15286 -
Exact OEM standards and specificatons. Correct fiberglass insulation, fittings, rubber hose and S clip.
Availability: In-Stock Item
Item #: 31551 -
This is the steel tube that goes from the carburetor to the fuel pump. Designed to fit OEM Carter X fuel pump with screws holding two halves together. Modern Carter fuel pumps are crimped and will need some bending of this tube to fit. Please see item 11761 tube for use with generic Carter fuel pumps.
Availability: In-Stock Item
Item #: 14008 -
This is the steel tube that goes from the carburetor to the fuel pump. Designed for vehicles LO-VOL fuel pump, fits 67 - 70 Mustang, 67 Cougar 390, 67 Fairlane and Torino.
Availability: In-Stock Item
Item #: 14258 -
Often when your fuel gauge is acting up, this is the culprit, not the gauge or sending unit. The problem with these brass floats, is that after year of being in contact with fuel, they will begin to corrode and disintegrate. We suggest going with the new foam floats. They are fuel resistant and will last longer. Find it here. Replaces Ford part #C0AZ-9202-B.Check out the video below on our new gauge tester: ...
Availability: In-Stock Item
Item #: 14205 -
Replaces Ford part #C0AZ-9A307-B.
Availability: Used / Wrecking Yard Item
Item #: 23791 -
Good used ring with only surface rust and no obvious gouges.
Availability: In-Stock Item
Item #: 11268 -
This is the single prong version fuel sending unit for 67 - 68 Cougars and Mustangs. Cougars equipped with the convenience control package, and the XR7's used a three prong version. The function however is not as good as original but adequate and usually will work for years. If you have an original, often times it's just the float that needs replacing, so don't be quick to discard your original. *Note - This reproduction sending unit is technically a copy of the 1968 version. Be aware that the...
Availability: In-Stock Item
Item #: 10117 -
This is the stainless steel, single prong version fuel sending unit for 67 - 68 Cougars and Mustangs. Cougars equipped with the convenience control package, and the XR7's used a three prong version. These units are better than original being made from stainless. The function however is not as good as original but adequate and usually will work for years. If you have an original, often times it's just the float that needs replacing, so don't be quick to discard your original. *Note - This...
Availability: In-Stock Item
Item #: 18898 -
Exclusive to WCCC, here's our reproduction in-tank, fuel sending unit with the low fuel option. Good for all 1967 - 1968 Mercury Cougar XR7's and all Ford Mustangs with 16 gallon fuel tanks. This is a reproduction of a 1968 fuel sending unit with three prongs (2 electrical and 1 alignment prong). The original Ford casting number was C8ZF-9275-B, master parts catalog number C8ZZ-9275-D. This unit comes with a new 3/8 inch filter, brass float, and sending unit gasket. These are completely...
Availability: Out of Stock
Item #: 30371 -
This plastic protector sleeve is often missing or broken, but occasionally we come across a good used one. This part attaches just in front of / below the fuel tank on the passenger side, and serves two purposes: it routes the wiring closer to the fuel sending unit without it dangling down, and protects it from road debris This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of 50% of our...
Availability: In-Stock Item
Item #: 30513 -
Often when your fuel gauge is acting up, this is the culprit, not the gauge or sending unit. The benefit of using this foam float, is that sometimes the hollow brass float will leak, causing a bad reading. This foam version of the float is fuel resistant and will never leak. Replaces Ford part #C0AZ-9202-B.Check out the video below on our new gauge tester: ...
Availability: Out of Stock
Item #: 31210 -
This is a single plug (standard models without low fuel warning light) fuel sending unit with an extra bung for a return line for 1967-68 Cougars and Mustangs running fuel injection. No need to change the whole tank in order to upgrade your car to fuel injection! Main line 3/8" Return line 1/4" Check out the video below on our new gauge tester: ...
Availability: Ships Direct from Supplier (Except International)
Item #: 32191 -
This option requires that you send your core in advance. Your core gets rebuilt and returned. If you don't have a core, WCCC has come across a few from our wrecking yard, give us a call to discuss details. Our service is to rebuild your sending unit. A quality core is required. Yes, we can rebuild other than 1967-73 Mercury Cougar and Ford Mustang sending units. 1967-1980 Ford / Mercury / Lincoln sending units accepted. See our related listing for non-low fuel sending unit rebuilding. A...
Availability: In-Stock Item
Item #: 32404 -
This option requires that you send your core in advance. Your core gets rebuilt and returned. If you don't have a core, WCCC has come across a few from our wrecking yard, give us a call to discuss details. Be aware that the OEM Ford 1967 sending units had 5/16 inch tubes for the filter, 1968 had 3/8 inch tubes.Our service is to rebuild your standard fuel sending unit. A quality core is required. Yes, we can rebuild other than 1967-73 Mercury Cougar and Ford Mustang sending units. 1967-1980...
Availability: In-Stock Item
Item #: 32439 -
Used retaining ring for the fuel sending unit or vent on 1971 and newer tanks. Fits a little tighter than the reproduction rings. Ford part #C0AZ-9A307-B.
Availability: In-Stock Item
Item #: 15999 -
Reproduction heater dash plate for the 67 Cougar or Mustang. Included are the plate, 4 piece knobs and hardware. Keep in mind that this face plate has the pebble grain finish which was standard to Mustangs (Cougars had the smooth finish).Replaces Ford part number C7ZZ-18A651-B
Availability: In-Stock Item
Item #: 26062 -
Perfect fit, easy to replace and will be a great upgrade over your original scratched and or pitted knob. To remove, reach behind the dash and locate the small, round spring loaded button on the top side of your headlight switch. Depress the button while firmly grasping the knob and move back and forth until it releases. To install, firmly and quickly press the knob inward (towards the dash) with the palm of your hand.Here is a helpful youtube video on how to go about removing a headlight...
Availability: In-Stock Item
Item #: 26128 -
Quality chrome and fit. Replaces Ford Part #: C7ZZ-11650-A. Here is a helpful youtube video on how to go about removing a headlight switch from a Cougar or Mustang.