Home > 1972 Mercury Cougar
All Available Parts - 1972 Mercury Cougar
Products (Click sub-categories above to ONLY display results for that Sub-Category) 301-400 of 3477
Sorted By:
Availability:
Display Options:
Availability: Used / Wrecking Yard Item
Item #: 11-0394 -
Used driver side (left hand) quarter window regulator for the Mercury Cougar or Ford mustang equipped with power windows. Ford part number D1ZZ-6530381-A *NOTE* If your also having some issues with your rear pancake window motor, check out our video below. It will take you through the pancake motor refurbishing process. If we can do it, there is no reason why you can't too! ...
Availability: In-Stock Item
Item #: 26153 -
Replaces Ford Part #C7AZ-6243629-A. Not used on 1967-78 trunk locks.
Availability: Used / Wrecking Yard Item
Item #: 25204 -
Used on the 1970 Ford Mustang, 1970 - 1971 Cyclone and Torino and 1971 Cougar style steel wheel 14 x 7". Master Parts Catalog description: 15-1/4" O.D., 11" I.D., 2-3/4" wide. This ring will have one or two very small scratches or dings that will not be easily fixed, driver quality.Ford part number D0ZZ-1210-BFord superseded this part with part number D4WY-1210-A
Availability: Used / Wrecking Yard Item
Item #: 19701 -
The majority of the rocker moulding end clips we get look like this unit in that the stud is broken or the wire tensioner has been broken off. Putting a new stud in one of these clips is not a hard job.
Sold Individually.
Availability: Used / Wrecking Yard Item
Item #: 25394 -
Ten of these plastic clips are required per car, five on each side. Original clips with D1ZB-6510182-AA engineering number imprinted on them. Sold Individually.
Availability: Used / Wrecking Yard Item
Item #: 11-0175 -
Hard to find driver side regulator
Availability: Used / Wrecking Yard Item
Item #: 11-0176 -
Good used original regulator. Ford Part #: D1ZZ-6523208-B
Availability: In-Stock Item
Item #: 10721 -
Manufacturer calls this a torque pin kit, it consists of 3 pins. Pin diameter is 1/2 inch and are 13/32 inches long. Made from natural nylon. Fits most Ford vehicles with power windows from 1964 - 1973+.
Availability: In-Stock Item
Item #: 11080 -
Reproduction power window motor for the passenger side (right hand) door glass of the Mercury Cougar or Ford Mustang equipped with power windows. This unit is for the 69-73 Mercury Cougar, but only years 1971-73 for the Mustang. This is the same motor that found it's way into most all other Ford/Lincoln/Mercury cars in that year range as well. If you need the rear pancake style motor, you can find that here. *NOTE* This is the only version of the power window motor that is available at...
Availability: In-Stock Item
Item #: 11081 -
Reproduction power window motor for the driver side (left hand) door glass of the Mercury Cougar or Ford Mustang equipped with power windows. This unit is for the 69-73 Mercury Cougar, but only years 1971-73 for the Mustang. This is the same motor that found it's way into most all other Ford/Lincoln/Mercury cars in that year range as well. If you need the rear pancake style motor, you can find that here.*NOTE* This is the only version of the power window motor that is available at the moment....
Availability: Used / Wrecking Yard Item
Item #: 15802 -
Please remove your regulator prior to shipping. Be careful of the mechanical energy stored with the spring under tension. Used rear pancake power window motor that is in good original condition for the Mercury Cougar or Ford Mustang. This motor has been professionally tested and has been found to be in good working order. Typically, these motors are service replacement motors that have been replaced sometime in the car's life.Ford part # C9WY-6530304-A.If you are interested in our service that...
Availability: Used / Wrecking Yard Item
Item #: 13158 -
Used power window motor for the passenger side (right hand) door glass of the Mercury Cougar or Ford Mustang equipped with power windows. This unit is for the 69-73 Mercury Cougar, but only years 1971-73 for the Mustang. This is the same motor that found it's way into most all other Ford/Lincoln/Mercury cars in that year range as well. If you need the rear quarter window pancake style motor, you can find that here. ...
Availability: Used / Wrecking Yard Item
Item #: 13159 -
Used power window motor for the Driver side (left hand) door glass of the Mercury Cougar or Ford Mustang equipped with power windows. This unit is for the 69-73 Mercury Cougar, but only years 1971-73 for the Mustang. This is the same motor that found it's way into most all other Ford/Lincoln/Mercury cars in that year range as well. If you need the rear pancake style motor, you can find that here. ...
Availability: Used / Wrecking Yard Item
Item #: 22564 -
Non working core suitable for rebuild, not full of water and never been opened. These are located in the quarter panel. This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of 50% of our web price for parts delivered in hand or by carrier to our Brooks, Oregon location. If you're not interested in store credit, just shoot us an email and we will let you know if it's is something we can...
Availability: Used / Wrecking Yard Item
Item #: 32434 -
Special Phillips pan head screw for attaching the pancake motor to the quarter window regulator. 1969-73 Mercury Cougar and 1971-73 Ford Mustang. Weird threaded screw, called a triangle threaded screw. Slightly larger than 1/4-20. Unique and limited to quantity on hand. Three screws per regulator, sold individually. Ford part # 381530-S. *NOTE* For those of you who like to rebuild and refurbish your own parts, check out our video below. It will take you through the pancake motor...
Availability: In-Stock Item
Item #: 18646 -
Bare Metal oil pan. Has no paint, chrome, or protective coating. Replaces Ford Part #: C5ZZ-6675
Availability: In-Stock Item
Item #: 17771 -
Reproduction Small Block Painted Oil Pan for the Mercury Cougar or Ford Mustang 289 or 302
Availability: In-Stock Item
Item #: 41663 -
Cork Oil Pan Gasket for the 351 Cleveland Cork Oil Pan Gasket in the 1970, 1971, 1972 and 1973 Mercury Cougar or Ford Mustang.
Availability: In-Stock Item
Item #: 41450 -
Quality After-Market oil filter for the 1967 - 1973 V-8 Mercury Cougar or Ford Mustang. Better filter than OEM.
Availability: In-Stock Item
Item #: 17773 -
Nice reproduction oil pan, painted stock Ford blue on the exterior.
Availability: In-Stock Item
Item #: 41276 -
[No Description Provided]
Availability: In-Stock Item
Item #: 11356 -
Nice reproduction oil pan for 351 Cleveland engines. Includes baffle and drain plug. Bare metal, ready for your choice of paint.
Availability: Discontinued
Item #: 15548 -
Availability: In-Stock Item
Item #: 15380 -
One piece molded rubber gasket with metal core. Keeps the rails flat and rigid, and prevents damage from over-tightening. Made by Fel-Pro. Oil pan SnapUps are included for easy mounting. This is by far the best oil pan gasket on the market.
Availability: In-Stock Item
Item #: 11006 -
New oil pan drain plug with zinc coating and plastic gasket. Fits all Mercury Cougar and Ford Mustang V8 oil pans 1967-73.
Availability: In-Stock Item
Item #: 11007 -
Replacement oil pan plug that is magnetized for collecting ferrous metal in the oil system. Replaces Ford part number C5ZZ-6730-M and D1AZ-6730-A. Fits all Ford engines 1967-73, including 6 cylinder, 289, 302, 351w, 351c, 352, 390, 427, 428, 429, 460.
Availability: In-Stock Item
Item #: 11003 -
Reproduction oil pan bolt kit for the Mercury Cougar or Ford Mustang equipped with the 289, 302, or 351W engine.
Availability: In-Stock Item
Item #: 13120 -
New oil pan drain plug, Ford engine blue painted, with plastic gasket. Looks correct, but has a different sized head than factory oil pan bolts. Correct 1/2" - 20 bolt diameter and thread pattern for factory Mercury Cougar and Ford Mustang V-8 oil pans 1967-73.Replaces Ford part # D1AZ-6730-A / D1AZ-6730-B (bolt) & C2OZ-6734-A (gasket).The Ford Master Parts Catalog lists bolt D1AZ-6730-B as the service replacement for all factory oil pans for the 200,...
Availability: In-Stock Item
Item #: 13121 -
New Chrome oil pan drain plug, with plastic gasket. Has a different sized head than factory oil pan bolts.Correct 1/2" - 20 bolt diameter and thread pattern for factory Mercury Cougar and Ford Mustang V-8 oil pans 1967-73.Replaces Ford part # D1AZ-6730-A / D1AZ-6730-B (bolt) & C2OZ-6734-A (gasket).The Ford Master Parts Catalog lists bolt D1AZ-6730-B as the service replacement for all factory oil pans for the 200, 240, 250, 289, 302, 351, 352, 410, 427, 428, and 429 engines 1965-1973. ...
Availability: In-Stock Item
Item #: 41177 -
Fits 1967 - 1973 Standard or XR7. Pins not used on 71-73 buckets.
Availability: In-Stock Item
Item #: 41188 -
Fits 1967 - 1973 Standard or XR7
Availability: In-Stock Item
Item #: 13921 -
Secures cable to heater control assembly, heater plenum and heater box. Black oxide bracket with screw.Replaces Ford part number 378897-S
Availability: In-Stock Item
Item #: 41214 -
Fits 1968 - 1973 Standard or XR7
Availability: In-Stock Item
Item #: 26619 -
Holds insulation to the firewall. Sold individually, 6 per car. Replaces Ford part # C8ZZ-6501691.
Availability: In-Stock Item
Item #: 41365 -
This is the rubber spacer / washer that goes between the bolt head and the metal washer of your seat belt hardware. The purpose of the rubber washer is to dampen any vibrations caused by the movement of the seat belt.Sold individually# 354959-S
Availability: In-Stock Item
Item #: 41355 -
Sold individually # 374212-S
Availability: In-Stock Item
Item #: 14043 -
Concours correct for 67, but a nice dress-up item for 68-73. Replaces Ford Part # 382627 Four bolts, four washers and eight rubber washers in mounting kit.
Availability: Used / Wrecking Yard Item
Item #: 27356 -
Engine oil dipstick as found on most any 1970-73 Ford with 351 Cleveland engines (H, or M Code), 1972-73 (Q code). Ford used several different suppliers and there are differences that show up in the finger handle as shown. Top of the shield to the dipstick end is approximately 21-11/16 inches. The handles were painted blue originally. Ford part # D0AZ-6750-A, Ford casting # D0AE-6750-A.*NOTE* In 1970 351W engines also were designated as H codes, 351W has 6 bolts attaching the valve covers,...
Availability: In-Stock Item
Item #: 13862 -
Brightens the engine compartment and looks sharp. Fits our big block finned aluminum valve covers (item# 26018) and others with the round push-in style opening. Requires a rubber grommet to fit into the valve cover, which is usually included with new valve covers.Does NOT fit valve covers with the "stovepipe" fitting (like our small block finned aluminum units) or factory valve covers the tabs for twist-on oil caps. This cap is for after market valve covers.
Availability: In-Stock Item
Item #: 13860 -
Brightens the engine compartment and looks sharp. Fits aftermarket valve covers only. These require a rubber grommet to fit into the valve cover. Please Note: This oil cap DOES NOT fit the finned "G" valve covers we sale, as they are built to OEM specs.
Availability: Used / Wrecking Yard Item
Item #: 14-1240 -
These spacer / washers were used on the rear belts of 1968 - 1973 Cougars. 1968 used two per bolt for a total of eight, 69-71 used one per rear belt for a total of four and 72-73 used one per belt on the inner only as the outer belts had a re-tractor in the rear 72-73. They were red to guide the line workers on placement.
Availability: In-Stock Item
Item #: 11600 -
Bulk pack of 100 oval head phillips screws for door and window crank handles.
Availability: In-Stock Item
Item #: 32500 -
These spacer / washers were used on the rear belts of 1968 - 1973 Cougars. 1968 used two per bolt for a total of eight, 69-71 used one per rear belt for a total of four and 72-73 used one per belt on the inner only as the outer belts had a re-tractor in the rear 72-73. They were red to guide the line workers on placement. Sized like the originals, but do not have the dimples all over. 0.53" ID x 0.88" OD.
Availability: In-Stock Item
Item #: 41154 -
Not 100% correct, but close and functional. In 1967 - 1968 there were eight per wheel lip moulding, two per fender extension moulding, two per center grille moulding and five per hood lip moulding for a total of 50 screws. In 1969 - 1973 they were used on the wheel lips mouldings. The 1971 - 1973 hood lip mouldings used the same screw but it was 5/8" tall. Sold as a box of 100.
Availability: In-Stock Item
Item #: 41238 -
Bolt for installing the front inner and outer bumper brackets to frame rail, and rear bumper brackets to body inside of trunk. Sold individually, 8 per car.
Availability: In-Stock Item
Item #: 27463 -
Original Ford style fasteners used on most all Ford products starting in 1968. Sold in pairs. Zink (dark silver)
Availability: In-Stock Item
Item #: 41306 -
These are the screws that are used to attach the door latch to the door shell on the 67 - 73 Cougar or Mustang. Sold in a set of 6.
Availability: In-Stock Item
Item #: 41359 -
Sold individually. Replaces Ford Part # 388052-S Helpful tip: Door panel clips install sliding toward the rear of the vehicle.
Availability: In-Stock Item
Item #: 41256 -
1/4-20x1 inch stud. Sold individually. Found on various years and parts of Cougars. Used for attaching 1967-68 grilles to the headlight buckets. Also as replacement mounting studs for front and rear fender and quarter extensions. Zinc Dichromate (yellow-rainbow)
Availability: In-Stock Item
Item #: 10745 -
Reproduction Phillips head screw that is used in a variety of applications on the Mercury Cougar or Ford Mustang. This phosphate & oil (gray-black) colored unit features a wide flat head and is used for attaching the stainless roof side weatherstrip rail. However, it has other interior applications as well. Sold individually. 24 required per car, set of 24 also available. ...
Availability: In-Stock Item
Item #: 27468 -
New plastic nut or insert for those 1/4 inch square holes in the grille for attaching the headlight doors (8 required there), and for the XR7 door pull panel mounting plates for attaching the actual door handles (2 required per side). Replaces Ford part # 379830-S1. Do you want to replace those worn out actuators yourself or are you looking for some great information on aligning the grille in your Cat? The videos below are your ticket! ...
Availability: Out of Stock
Item #: 32909 -
24 Reproduction Phillips head screws that are used in a variety of applications on the Mercury Cougar or Ford Mustang. This phosphate & oil (gray-black) colored unit features a wide flat head and is used for attaching the stainless roof side weatherstrip rail. However, it has other interior applications as well. Also sold individually.
Availability: In-Stock Item
Item #: 41037 -
Replaces Ford part # C2DZ-6A529
Sold Individually.
Availability: In-Stock Item
Item #: 41002 -
This is the shorter version of the top-loader with no "+" on the head.
Sold individually
Availability: In-Stock Item
Item #: 41023 -
Replaces Ford part # 385664-S
Availability: In-Stock Item
Item #: 41228 -
Sold individually
Zinc (dark silver)
Availability: In-Stock Item
Item #: 41245 -
Four of these bolts are used to secure the isolator portion of the engine mounts to the 289/302/351 blocks. Includes 351W and 351C engines. 5/8" hex head bolt. Sold individually Concours phosphate & Oil (gray-black).
Availability: In-Stock Item
Item #: 41229 -
Sold individually
Zinc (dark silver)
Availability: In-Stock Item
Item #: 41239 -
Sold individually
Zinc (dark silver)
Availability: In-Stock Item
Item #: 14187 -
This clip holds the speedometer cable gear to the end of the cable. Replaces Ford Part # : C1DZ-17292
Availability: In-Stock Item
Item #: 41243 -
Reproduction dark zinc starter bolt for the Mercury Cougar or Ford Mustang equipped with the small block engine. These units are sold individually.
Availability: In-Stock Item
Item #: 41360 -
These little rivets are used to affix the ID tag to the passenger side of the 3 and 4 speed top-loader transmissions. Most tags are held in place by two rivets but on some only two are used from the factory.
Availability: In-Stock Item
Item #: 41244 -
Sold individually.
Zinc Dichromate (yellow-rainbow)
Availability: Out of Stock
Item #: 41416 -
Reproduction Anchor Strap - Tape In for the 1967 - 1973 Mercury Cougar / 1967 - 1973 Ford Mustang
Availability: In-Stock Item
Item #: 41166 -
Complete engine mounting kit for the 390 engine with standard exhaust. See list below for included hardware.Click on images to enlarge. ...
Availability: In-Stock Item
Item #: 43841 -
Four needed per fan shroud. Sold individually.Ford Part Number: 383152-S
Availability: In-Stock Item
Item #: 12460 -
Set of 4 reproduction torque converter nuts for the Mercury Cougar or Ford Mustang.
Availability: In-Stock Item
Item #: 31569 -
New Bolt kit, for the installation of a water pump on any Ford 351C or 351 Cleveland engine. Fits all 1970-74 Mercury Cougar and Ford Mustang with 351C, 351CJ engines. 11 total pieces in the kit as shown.
Availability: In-Stock Item
Item #: 32159 -
Four of these bolts are used to secure the isolator portion of the engine mounts to the 289/302/351 blocks. Includes 351W and 351C engines. 5/8" hex head bolt. Sold as a set of 4. Concours phosphate & Oil (gray-black).
Availability: In-Stock Item
Item #: 41362 -
Reproduction steering gear or seat belt washer for the Mercury Cougar or Ford Mustang. These units are sold individually.Replaces Ford part # 378580-S.
Availability: Out of Stock
Item #: 41346 -
Sold as a Pair. Ford Part #: C8AZ-2B296-ACheck out our caliper tips and tricks video below: ...
Availability: In-Stock Item
Item #: 26755 -
9" inside the arch to the end of the threads. Thread size 7/16-20, includes tall nuts as shown. Concours Grade 5 flange nuts available separately, see related items.
Availability: In-Stock Item
Item #: 41134 -
Replaces Ford Part # 381985-S Sold individually
Availability: In-Stock Item
Item #: 41271 -
Factory OEM style clamp for attaching the brake booster vacuum hose to the check valve. Also same clamp for securing the rubber boot to the power steering ram cylinder. Sold individually.
Availability: In-Stock Item
Item #: 41135 -
These brackets are intended to make sure that the brake pads and the caliper stay in the correct alignment, as well as for anti-rattle. Replaces Ford Part # C8OZ-2B295-A. Sold individuallyCheck out our caliper tips and tricks video below: ...
Availability: In-Stock Item
Item #: 41136 -
Replaces Ford Part # 382713-S Sold individuallyCheck out our caliper tips and tricks video below: ...
Availability: In-Stock Item
Item #: 41130 -
Replaces Ford Part # C8AZ-2066-A
Sold individually
Availability: In-Stock Item
Item #: 41133 -
Reproduction disc brake caliper insulators for a large array of FoMoCo products starting in 1968. 2 are required per caliper, 4 total per vehicle. Sold as a pair. Replaces Ford part # C8AZ-2B299-A.Check out our caliper tips and tricks video below: ...
Availability: In-Stock Item
Item #: 41129 -
Replaces Ford Part # C8AZ-2069-A
Sold individually
Availability: In-Stock Item
Item #: 41131 -
Replaces Ford Part # 43260-S
Sold individually
Availability: In-Stock Item
Item #: 41040 -
This nut fits onto the strut brace at the front of the car, and not the control arm end. It is the lock nut that goes on after the the bigger strut rod bushing nut.Replaces Ford part # 340460-S
Availability: Used / Wrecking Yard Item
Item #: 26513 -
This clip is the same as a door panel clip with the exception that it does not have the foam spacer. This clip was used on the 1968 XR7 overhead console, 1967 - 1968 xr7 and standard model upper and lower console pads, seat back access panels and several other applications. This original clip holds tighter than the reproduction. We recommend using this used clip over our reproduction for applications like the seat back because the reproductions often do not cut it. Ford part number...
Availability: Used / Wrecking Yard Item
Item #: 11-0354 -
Two or three of these clips were needed per door to mount the padded armrest. Three were used per armrest for a total of six, on 1969-70 Cougar and Mustangs. Two used in 1971-73 on standard Cougars. Sold individually.Replaces Ford part # C6AZ-6224146-B.
Availability: Used / Wrecking Yard Item
Item #: 14-1002 -
Used in multiple applications front and rear lap belts. Inner and outer, marked with a letter "B" in at least three known fonts. 1-3/4 inches long, 1/2 inch shoulder, Torx 50 tool for installation and removal.
Availability: Used / Wrecking Yard Item
Item #: 14-1038 -
Two per car, identified with the letter "D" in three known fonts. This bolt was used in conjunction with a chrome spacer / washer that is also marked with the letter "D". 1-1/2 inches long, 1/4 inch shoulder, use a Torx 50 for installation and removal.
Availability: Used / Wrecking Yard Item
Item #: 14-1244 -
Used on inner and outer rear seat belt bolts, four per car in 1970 -1971 and used only on the inner rears in 72 - 73 due to the addition of rear retractors. Used in conjunction with two red washer / spacers, marked with three known font styles of the letter "A". 1-5/16 inches long, Torx 50 is the tool for installing and removing.
Availability: Used / Wrecking Yard Item
Item #: 23774 -
One per side, 1968 does not use the triangle markings. The letter "D" stamping was in place to aid line workers with correct placement on the car.
Availability: Used / Wrecking Yard Item
Item #: 23783 -
Often you will see minor irregularities in these washers. These would be considered "blems". Two required per car, used only on the re-tractors.
Availability: In-Stock Item
Item #: 41140 -
Replaces Ford Part # 382626-S
Sold individually
Availability: In-Stock Item
Item #: 13066 -
Two or three of these clips were needed per door to mount the padded armrest. Three were used per car for a total of six, on 1969-70 Cougar and Mustangs. Two used in 1971-73 on standard Cougars. Sold individually.Replaces Ford part # C6AZ-6224146-B.
Availability: In-Stock Item
Item #: 31193 -
Reproduction shoulder belt bolt spacer for the 69 - 73 Cougar or Mustang. Does not have markings like the originals. One per side, two per car.
Availability: Used / Wrecking Yard Item
Item #: 11-0459 -
Used single bolt for attaching door and quarter window regulators on any 1969-73 Mercury Cougar or Ford Mustang or Ford anything most likely. Sold individually
Availability: In-Stock Item
Item #: 31883 -
New single bolt for attaching door and quarter window regulators on any 1969-73 Mercury Cougar or Ford Mustang or Ford anything most likely. AMK part. Sold individually
Availability: In-Stock Item
Item #: 33532 -
Reproduction bolts and washers for the shoulder belts on any 1969-73 Mercury Cougar or Ford Mustang. Includes 2 each of the "D" bolts and chrome thick washers. Quality AMK kit F-3563.
Availability: In-Stock Item
Item #: 33533 -
AMK seat belt washer B-13023. 0.46" ID x 1.25" OD zinc flat washer. Sized so that it rides on the shoulder of the seat belt bolts. It allows the retractor to rotate freely between this washer and the head of the seat belt bolt on 1969-73 cars. Two required per car, used only on the re-tractors.
Availability: Rare / NOS Part
Item #: 15542 -
Phosphate & Oil finish. Sold individually. Replaces Ford part #: 378782-S
Availability: In-Stock Item
Item #: 41004 -
This is longer of the two with the + on the bolt head.
Availability: Rare / NOS Part
Item #: 41024 -
Availability: In-Stock Item
Item #: 41025 -
Ford manual transmission flywheel and automatic transmission flex plate mounting bolts. 6 bolts required, sold individually. Replaces Ford part # 378172-S
Availability: In-Stock Item
Item #: 41038 -
Replaces Ford part # 55806-S