1968 Ford Mustang

Used cigar or cigarette lighter threaded retainer with ground lug. Fits any 1969 Mercury Cougar and Ford Mustang with factory installed console. The ground lug is needed for the heating element in the socket. The consoles are made of plastic and use the common socket designed for steel dashes. This retainer is part of C9MB-15055-A socket and retainer assembly. 

Retainer or keeper for door hinge pins on all 1968-73 Mercury Cougar and Ford Mustang, plus most all other Ford products with a typical door hinge pin. The factory installed the hinges with the pins driven in from the bottom as viewed with the doors installed. Most restorations install the pins from the top so that gravity holds them in. These retainers allow the pins to be mounted concours correctly. You must use a socket or other tool to install. These fit the door hinge pins with 5/16 inch...

Used rear retainer for the ignition lock cylinder on any 1967-68 Mercury Cougar or Ford Mustang. Good value, used as they come out of the cars, will have some flash rust since they were never plated or painted, usually it will not come with the small screw. This unit locates and maintains the angle to the dash from behind. Attaches with one small screw, and the bezel and retainer nut secures the whole works to the dash from the front. 1967-68 Mercury Cougar and Ford Mustang. 

Push on retainer for rear drum brakes. 2 or 3 of these were used to hold the rear brake drums onto the rear axle assembly during construction of your 1967-73 Mercury Cougar or 1965 - 73 Ford Mustang. While not necessary, these are a neat concours item. Sold individually.  Ford part number 372188-S

Cougar actually used a larger ribbed plate on manual transmission cars without a console but this Mustang part is an inexpensive alternative. The rubber shift boot screws to the transmission tunnel, carpet then goes over it and lastly this retainer slips over the boot and hides the cut edges of your carpet. Shift boot sold separately.Replaces Ford Part #: C5ZZ-7262-C.

Used steering column tube retainer for the 67 - 69 Mercury Cougar or Ford Mustang equipped with the tilt / tilt away steering column. These little units help hold the steering column together and there are 3 required per column. Sold individually. This are not advisable in the 1970 and later cars. Ford part # C7SZ-3499-A. *NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our...

Reproduction lower ball joint retainer and gasket. Works on 67 - 73 Cougars and Mustangs.

Reproduction retainer clip for the back up light switch wiring on the 67 - 69 Cougar or Mustang equipped with a 3 or 4 speed transmission.Replaces Ford part number C7ZZ-14163

This reproduction clip secures the clutch pedal rod end as it comes through the clutch pedal hanger.  Keep in mind that this reproduction is a different size compared to the original (see comparison above) and will need to be modified to make fit. As always, we recommend going with original used parts. You can find it here. Replaces Ford part number C8AZ-2B277-A ...

Plastic insert with metal locking retainer. Replaces Ford part # C5AZ-6221952-A. NOTE* This clip will need to be squeezed on the clip side in order to obtain a good grip. Check out our handy diagram below to find other '67-'68 door parts you may need. All the item numbers shown can be typed in to the search bar on our site. (Click image to view full size) ...

Plastic insert with metal locking retainer. The plastic came in various colors, white, red, and black are common. Replaces Ford part # C5AZ-6221952-A.Check out our handy diagram below to find other '67-'68 door parts you may need. All the item numbers shown can be typed in to the search bar on our site. (Click image to view full size) ...

Reproduction emergency / parking brake retainer clip set for the Mercury Cougar or Ford Mustang. These units are sold in a set of 3.

Used door lock and trunk lock cylinder retainer clip. Not exactly the same as the door lock clips. Trunk clips have the small hole, a hooked tool would be used for removal. Not used on 1967 - 1968 Cougar trunk lock cylinders. *Note - For use on Cougar trunk locks built prior to 3-1-1972. Please see Ford part number D2WY-6243629-A for your Cougar needs on cars built after 3-1-1972 (used only).

Used retainer / friction clip that replaces broken injected plastic shaft retainers on fixed or tilt steering collapsible columns on most FoMoCo products starting in 1968 and through the 70's. Ford part number C9AZ-3E629-B. *NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year. ...

Reproduction 3D printed retainer / friction clip that replaces broken injected plastic shaft retainers on fixed or tilt steering collapsible columns on most FoMoCo products starting in 1968 and through the 70's. These installs on the upper piece of what Ford called the Steering Column Shaft Assembly, also known as the inner steering column collapsible shaft.  The Steering Column Shaft Assembly is the 2 piece shaft that connects the steering wheel to the rag joint. The upper...

Reproduction heater resistor attaching pins correct for 1967-68 Mercury Cougar and Ford Mustang, but works fine with 1969-73 cars too. Sold in sets of 2 pins.

Used retaining bolt with nut for the fixed column on any 67 - 68 Cougar or Mustang. 2 of these bolts are required to holt the two sections of the upper column sleeves together.  Sold individually, 2 per column.

Spring steel clip located under the drive cable housing as seen on page 16, figure 19 of our free download of the sunroof panel service procedure manual.

Used grade A side mirror retaining nut for the 1968 Mercury Couga or Ford Mustang. Grade A's will have no scratches or dings.Ford part number C8ZZ-17B719-A

Used grade A side mirror retaining nut for the 1968 Mercury Couga or Ford Mustang. Grade B's will have minor scratches or dings. Ford part number C8ZZ-17B719-A

Replaces the original Ford part that features a # C7SB-17B732-A casting number. Basically correct for 1967 but works just as well on 1968 mirrors. These nuts are are not 100% correct for a 67 or 68, kind of a mixture of both.Very nice chrome quality at a reasonable price. NOTE: Our mirror nut removal tool works & fits perfectly with the original mirror nuts. However, you will find the tool will NOT fit this reproduction nut properly, it will require that it be filed a...

Replaces Ford part #C0AZ-9A307-B.

Good used ring with only surface rust and no obvious gouges.

Used retaining ring for the fuel sending unit or vent on 1971 and newer tanks. Fits a little tighter than the reproduction rings. Ford part #C0AZ-9A307-B.

Used retaining spring and two screws for attaching the break away air conditioning vents to any 1968 Mercury Cougar or Ford Mustang with factory installed A/C.

We all love the look of classic sealed beam headlights, but the dim halogen light output makes nighttime driving potentially risky for you and your beloved classic. Holley's new RetroBright LED Modern White Headlights offer a number of advantages over traditional sealed beam headlights such as plug and play compatibility, better visibility, and 6 times longer life. Not only that, but because they are LED they take up less space, create far less heat, and use less power than other headlights....

Reproduction pump end return hose for the 67 - 70 Cougar or Mustang. Cut to 2' length.

High Quality 400 PSI pump to valve return line. This is the control valve to the return hose that comes from the power steering pump on all big blocks and the 1969 and 70 small blocks, and will work for the 1967 or 1968 small blocks with the 5/16 inch control valve fitting if the power steering hoses are routed the same as on the big block engines. The big block routing is far superior to the original routing as the original routing was susceptible to rubbing against the exhaust manifold. This...

We have created all of the components needed to economically install the steel nutsert or Riv-nut for the exterior mirrors that mount to the car doors. Our steel Riv-nut uses a 1/4 inch hole. You will need a 5/32 Allen or hex key, 3/8 inch wrench, and a 7/16 inch wrench. The Riv-nut needs to be assembled on the kit as shown prior to installation. The assembly is installed flush, in the pre-drilled hole. The Allen wrench and the 7/16 are held stationary, while the 3/8 wrench is used to tighten...

Correct rivets for use after you have painted your car or installed a new door. No special tools needed for installation. Simply lightly tap the center recessed portion with a small bolt or blunt punch. If your plate is missing you can obtain a correct reproduction with your unique codes at www.martiauto.com. Sold as a pair. Replaces Ford Part #: C5ZZ-6223000-A or 354921-S.

Inner rectangular clip to hold on the rocker panel moulding on a 1967 or 1968 Ford Mustang or Mercury Cougar. Sold Individually.NOTE - We've found that these reproduction clips do not work as well as the originals, you may find it a bit hard to install the rockers onto these clips without having to apply too much pressure, causing unwanted bending.

Used plastic rocker moulding clip for 1968 Mercury Cougar and 1967-68 Ford Mustang. Used clip, originally pop riveted onto the rockers. Sold individually. Ford part number C7ZB-6510182-A.

The Rocket "Strike" provides timeless and classic traditional styling at very affordable prices. The Rocket Strike is a 1-piece wheel precision crafted from A356 aluminum and topped off with a vintage style aluminum o-ring center cap. It has a lug centric design and uses standard 60-degree conical seat lug nuts (sold separately). There is 3.00 inches of hub clearance under the center cap. Load rating is 1560 lbs per wheel.4.25 Back spacingFully polished center and outer rim.  Cast...

This rod for the midland vacuum brake booster adusts to a maximum length of 4 1/16" and minimum length of 4 1/2" and is a very good copy of the original. Made in America.

This rod for the midland vacuum brake booster adusts to a maximum length of 4 1/16" and minimum length of 4 1/2".  This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of 50% of our web price for parts delivered in hand or by carrier to our Brooks, Oregon location. If you're not interested in store credit, just shoot us an email and we will let you know if it's is something we can...

Used roll up door for the Standard Mercury Cougar's center console. Finished metal front on flexible rubber back. Includes chrome knob. Different from the 1967 door in that it has the much wider handle. Ford part # C8ZZ-6506024-A. Customer review: Called WCCC the other day after calling around to a lot of garages and auto parts stores trying to find out the torque specs for my rocker arms on my Cougar. I wanted to check to make sure they where in specs when I was replacing my valve cover...

This is the nylon roller that fits on the end of the window regulator arms. Includes rivet.Sold individually. 2 rollers required per window, 4 rollers required per car.Replaces Ford part number C5AZ-57262A32-A. Dimensions: 11/16" DiameterHere's an instructional video on how to install the rollers. Keep in mind that this is a YouTube video from Danchuk Manufacturing installing a different type roller, but the technique is the same: 1969 Glue-In Glass: The Comprehensive Repair Guide Video ...

Reproduction of the very hard to find window roller for the window channel / quarter window frame on the 67 - 68 Cougar and Mustang. Doubles as both the single and double type roller (with the included support washer).Included in this kit are: One roller, one rivet, one wavy washer, one flat washer, and one support washer, measures exactly 1" wide. Rivet is for a 1/4" hole.2 required per door glass channel, 3 per quarter window frame.Sold individually. Replaces Ford Part # C8SZ-57262A32-A....

Used roller for any 1967-68 Mercury Cougar or Ford Mustang hardtop or convertible rear quarter glass channel. Also found on all 1967-68 Mercury Cougar and Ford Mustang door window channels. Often times one of the rollers breaks off and allows chattering of the window movement. Sold individually: 3 total rollers on each side of the quarter window brackets. 2 like this

Replaces Ford Part #: C0AB-6423240-B. Four required per car, two per side. If your quarter glass is loose in the track and will not roll up and down these rollers are most likely the culprit. When the tracks get gummed up and the window takes too much effort to roll up and down, these brittle old rollers will break. Even if they are not broken they are often frozen in place from rust and will not spin freely. From our experience every 1967 - 1968 Cougar needs these replaced if they still have...

Used single plastic roller for any 1967-68 Mercury Cougar or Ford Mustang hardtop or convertible rear quarter glass channel. Note that there is only one of this style of roller on each quarter window. This is a simple white plastic roller and a rivet. Note that there are 2 rollers with 2 pieces of round white plastic. Often times one of the rollers breaks off and allows chattering of the window movement. Included is a good roller and drilled out rivet. These can be reused if you drill out the...

Reproduction rubber roller for the metal tilt cover plate on any 1968-69 Ford, Mercury, or Lincoln. Often times the rubber disintegrates over time. This is needed to keep the cover plate tight to the side of the steering column. *NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year. ...

Reproduction roof / headliner insulation kit for your Mercury Cougar or Ford Mustang. An effective item that will increase the efficiency of your heater or A/C. This will also insulate your interior from outside sounds.

Reproduction roof brace for the 67 - 68 Cougar or Mustang. This is the leading front support on your roof, directly above your windshield.

Replaces Ford Part Number: B7A-12200-A / DR-5 And C5TZ-12200-A / DR-87 (Service Replacement)

This decal can be used to overlay your replacement oil filter, so it looks more like a vintage original oil filter. Research indicates that the gold was primarily used on 66 and earlier, as was the red. They then phased the red/gold out and replaced it with the white oil filter printed with the Autolite logo.   1967 Cougar/Mustang could have come factory installed with either red or gold. 1967 - 1969 factory serviced cars could have gotten the red or gold until stock was...

Permatex RTV gasket maker for the automatic transmission in your Mercury or Ford. Great stuff for sealing up that leaky transmission pan gasket!

New RTV gasket maker for use on the differential of your Mercury or Ford. This gasket maker is specially formulated to withstand today's gear oils and prevent leakage.