1968 Ford Mustang

This is a much higher quality bracket than other reproductions. Correct texture and fit. The bracket offered by most companies is just pot metal sprayed gray. Replaces Ford Part #: C7SZ-3A732-B or C7ZZ-3A732-B.

These Brackets are made from stamped steel just like the original, and built to Ford specifications for an exact fit. Available in correct OEM Black. customers looking for a little more flash under the hood might be interested in the highly-polished stainless steel version of this bracket! Replaces Ford Part #: C7ZZ-8A193-A. Check out our video on Radiator and Fan upgrades below: ...

Good reproduction but our used unit is a better value and will clean up just as nice.

Reproduction pair of mounting nuts for any 68 - 70 Cougar or Mustang with power brakes.

Reproduction support brace to be used with 1967-70 Mercury Cougar and Ford Mustang export braces. Can be used with OEM, NOS or reproduction export braces. Contoured to match the curvature of the cowl.*Note - Will not fit early Shelby Mustangs.This part never came from the factory, but the idea was taken from the fact that Shelby cars had plates like these, though these are not interchangeable with Shelby export braces or export brace plates because of hole placement. The original Shelby part...

Spare tire, with styled steel wheel hold down disc. Fits all 1968-70 Mercury Cougar and Ford Mustang. Original Ford part number C8MY-1424-A. About 3 inches in diameter, this is the specified trunk hold down plate for the use with the factory mag wheels.

Spare tire, with styled steel wheel hold down disc. Fits all 1968-70 Mercury Cougar and Ford Mustang.  About 3 inches in diameter, this is the specified trunk hold down plate for the use with the factory mag wheels. We won't always have the used in stock, but the reproduction version is very good.Replaces Ford part number C8MY-1424-A.

Used Nodular Iron 9 inch third member case, known as "N" - Case. typically found on cars with 427-4V, 428CJ, 429CJ, Boss 302, Boss 351, or Boss 429. These are the factory installed heavy duty third members typically with 31 splined axles. These are bare cases as shown. Current dates available: 8L27, November 27, 1968; 0E29, May 29, 1970. Please have your desired date in mind when calling or place it in the comments section of your on-line order. We have removed the peg leg gears and parts...

CRL brand glass bedding compound for installing the 1967-68 glass windshields and 1967-73 back glass that use rubber gaskets. This is a non-hardening material that seals the glass to the rubber

Application is for the FE engines 390, 427 428. This assembly is needed for the installation of the cylinder head air supply tubes. Sold as one nut / one ferrule. 8 total needed for smog tube attaching. Originally these were installed in conjunction with a lower tube.

Used set of four nuts and two locking washers used on the knob shafts of all radios 1967 - 1973 used on Cougars, Mustangs, Galaxie, Torino etc.

New rubber "O" ring for Ford V-8 distributors from 289/302/351W/351C/429 engines.

O Ring gasket for all automatic transmission dip stick tubes. Replacement gasket for C4, C6, and FMX trans dip stick tubes 1967-73 Mercury Cougar and Ford and Mustang.

OEM Style Transverse Resonator Exhaust Hanger 1967, 1968 and 1969 Mercury Cougar and Ford Mustang

Used 1970-72 black AUTOLITE marked oil fill cap with black plastic elbow. Several variations noted from our collection, AUTOLITE and MOTORCRAFT versions. Will need detailing or fresh black paint applied. Would also suggest replacing the rubber grommet. These 50 year old rubber grommets are rock hard and likely leak air. Gasket to valve cover will also need replacement. Even though this cap has a 1971 parts number, we see these on the 1970 351C engines quite often. Replaces Ford part...

Precision machined to the factory specifications. Light gold anodize finish just like the original.

Concours correct dipsticks for 1967 - 1969 big block engines. These are exact reproductions of the originals with the proper length and oil level for these big block FE's. They have all of the correct markings including the Ford part number and recommended oil weight. Each dipstick is finished with a show quality chrome handle capped with the correct plastic plug. Ford part # C7OZ-6750-A, Ford casting # C7OE-6750-A.

This oil filter is absolutely concours correct. A must for Show. All are silk-screened with multiple colors.

The oil filter made by the original Ford supplier.

New Old Stock oil filter adapter from any 1968-70 Ford with 390 or 428CJ (non SCJ). Fits Cougar, Mustang, Torino, Fairlane, Cyclone, Ranchero, etc. Nice cast aluminum bracket for installing the spin on oil filter and oil pressure sending unit. Ford casting number C8AE-6881-A. Will fit 1967 FE engine blocks too. Those technically used an adapter with a casting number of C0AE-6881-A.

Famous 'Cal Custom' aluminum finned oil pan that was so popular throughout the 60's, 70's and 80's. It has not been available for years, but it is back again. Pan is made from all new pressure die cast tooling and then fully machined to offer a precise fit and leak free installation. These look great in combination with the Finned Air Cleaner and Valve Covers. Replaces Ford Part #: C5ZZ-6675.

Includes drain plug.

Used oil screen pick up tube assembly from a FE or big  block 1966-70 Ford car, such as 352, 390, 410, 428, or 428CJ engine. This is for most front sump oil pans. Used item, should be degreased and cleaned inside and out prior to installation. Tube assemblies with damaged screens, damaged tubes or bends are thrown away or scrapped. We only save undamaged, used oil pick up tubes. Melling sells a quality reproduction of this item. Replaces Ford Part #: C6OZ-6622-A ...

Full passenger (right hand) side front frame rail that measures 52" long and the outer rail has weld nuts installed for proper installation. Fits: 1967 Mercury Cougar1968 Mercury Cougar1969 Mercury Cougar1970 Mercury Cougar 1967 Ford Mustang1968 Ford Mustang1969 Ford Mustang1970 Ford Mustang ...

This is identical to the 67 pad just slightly wider. 1968 was the introduction of many Federally mandated safety upgrades, the larger pedal being one of them. Replaces Ford part number D3ZZ-2454-A

WE CAN NOT SHIP THIS PRODUCT INTERNATIONALLY WITHOUT SHIPPING IT AS HAZARDOUS MATERIAL. THIS WILL INCUR HAZARDOUS MATERIAL CHARGES VIA UPS AND SOME COUNTRIES DO NOT ACCEPT IMPORTING THIS PRODUCT. This SEM plastic and leather paint prep is for cleaning surfaces before applying the SEM flexible vinyl paint. Removes mold, grease, oil and other contaminates from leather, carpet, velour and vinyl.

New pair of white and yellow paint sticks for the Mercury or Ford. These units were used by FORD at the assembly plants to mark fender aprons

Replacement rubber material pan gasket for all 1965-73 C4 Ford transmissions. 

Front steel vacuum fitting for 390, 427, 428CJ engines. New Old Stock. Replaces Ford part number C7AZ-9A474-A.

C7AE-6A666-B is stamped on this used PCV valve. Absolutely correct for 1968 390GT, 427-4V GT-E, and 428CJ Mercury and Ford cars. Must be used with either of the 90° elbows available, reproduction or OEM Ford.. This is used, no guarantee that it functions like new. Ford MPC number C7OZ-6A666-A. There is a published procedure for refurbishing these valves. These positive crankcase ventilation valve can be disassembled. ...

Used threaded PCV valve for use on 390-4V, 428CJ, 427-4V cars from 1967-70. Unknown functioning condition, these have the correct threaded tops and work with either of the 90° elbows available, reproduction or OEM Ford.

Pertronix brand 7mm spark plug wires. These are performance oriented wires compared to the concours spark plug wires. For any 1967-73 Mercury Cougar and Ford with 289 or 302 engines. Black wires and boots, quality spark plug wires taylor made for the small block Ford engines. Recommended by Pertronix for use with the Flame Thrower coils.

Used brake shoe guide plate, or anchor pin, that holds the top of the drum brake shoes together on your Mercury Cougar or Ford Mustang equipped with drum brakes. For the money our reproduction plate is a better value and cleaner, too. These have 1/2 inch holes in them.Replaces Ford part number C4UZ-2028-A.

Used brake shoe guide plate, or anchor pin, that holds the top of the drum brake shoes together on your Mercury Cougar or Ford Mustang equipped with drum brakes. For the money our reproduction plate is a better value and cleaner, too. These have 1/2 inch holes in them.Replaces Ford part number C4UZ-2028-A.

Reproduction pinion seal for the 9 inch ring gear on the 1967 - 1973 Mercury Cougar or Ford mustang. 

C3AZ-4730-B Rubber bumper that mounts to the metal axle snubber on Ford nine inch rear ends on 1967 - 1970 Mercury Cougar and Ford Mustangs. Good used part with solidly mounted metal threaded stud. Pinion bumper. The casting number seen on the 67-68 is C3AA-4906-C, this version has fine threads. The version most often seen on the 69-70 is C9OA-4906-A. It will have a coarse threaded mounting stud. Two of these were used on certain 1967 Shelby Mustangs with traction bars.

Used pinion yoke for an 9 inch rear end on any 1967-73 Mercury Cougar or 1967-73 Ford Mustang. 1310 U-Joint. Part cleaned for pictures, used parts shipped the way they come off of the cars. Shipped bare, no hardware included.Ford part number C3AZ-4851-L.

Used pivot pin for the Mercury Cougar or Ford Mustang / Thunderbird equipped with a tilt / tilt away column. This is a pressed pin with a flange and five are required per car. This pin is internally threaded with a # 6-32 thread. Ford part # C7SZ-3D739-A. *NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year. ...

This rubber plug is found on the bottom side of 68 and 69 Cougars without tilt column. It covers the access hole for the bolt that removes the column head / collar. We notice that most cars do not have them in place. This could be due to over site at the factory or them being lost over the years as the car has been serviced. We have also noted that Dearborn cars rarely if ever have them present and San Jose built cars often have them in place. If you have a Dearborn built car and have this...

C6AA-3D746-A Oil cooler used on all 1968 Shelby Mustangs with power steering. Both GT-350 and GT-500 models. www.thecoralsnake.com/TRIVIA.HTML 2-3 items down.

This item will have a refundable core charge added to your order. Multi-year power steering pump, 1967-69, and 1971-73, excludes 1970. When fully assembled you will notice that this year P/S pump has a centered fitting for the pressure hose on the back of the reservoir. Most factory 1970 Mercury Cougar and Ford Mustang have an offset fitting. The only 1970 exception is the R or Q code 428 Cobra Jet engines, they used this pump. Manufacurers note: In place of the paper gaskets, it is...

Cylindrical shaped brass valve, some times called the pressure control valve or 'cigar' valve. Starting in 1968, disc brake cars have it mounted almost directly on the Pressure Differential Valve on the driver side fender apron. The pressure differential valve is also commonly called the 'brake distribution block'. We also sell our brake distribution blocks complete with the proportioning valves. The C8OA numbered proportioning valve started way late for the 1968 model year. We almost...

Ford part number C8AZ-6A312-A. Application 390-2V, 390-4V engines, and 428 Cobra Jet with air conditioning. Power steering optional, with dual alternator belts. Ford casting number C8AE-6312-A. Triple sheave 68 crank pulley.

1968 390-4V all with factory manual transmissions and factory air conditioning. Pulley diameter 5.89" inches. Ford part number casting # C8AE-9B480-B. Mounting bolts sold separate.

C8OZ-8509-B 1968 289 or 302 with automatic and 1969 351. All without air conditioning but with power steering. Power steering optional if with dual belt alternators. Two sheave pulley, diameter of 6-7/16 inches. Ford casting number C7OE-8509-D. Overall height or depth is 2-7/16 inches.

C8OZ-8509-C 1968 427 / 390-4V without air conditioning and 1968-1970 428CJ without air conditioning. Thermactor on all applications, power steering optional. 3 sheave pulley with two different diameters. The MPC lists it as 6 inches on the dual sheave portion and 5-1/16 inches on the outer but we find the actual outer most measurements to be 6 1/8" wide on the dual pulley and 5 3/16" wide on the single sheave pulley. When laid on a flat surface the height is 2 3/8" tall. Ford casting number...

Good used driver side (left hand) quarter window guide for the Mercury Cougar or Ford Mustang. Grade A will have no rust or erosion from moisture. This unit will have all three window stops and both window guides still attached. Riveted window stops have part number of C4ZB-6529838-A. Ford part # C7ZZ-6529753-A. Do you have questions about Glue-In vs Bolt-In glass? How about how to properly install Glue-In glass in your 1969 Cougar or Mustang? Check out our video below for some great...

Good used passenger side (right hand) quarter window guide for the Mercury Cougar or Ford Mustang. Grade A will have no rust or erosion from moisture. This unit will have all three window stops and both window guides still attached. Riveted window stops have part number of C4ZB-6529838-A. Ford part # C7ZZ-6529752-A. Do you have questions about Glue-In vs Bolt-In glass? How about how to properly install Glue-In glass in your 1969 Cougar or Mustang? Check out our video below for some...