Body

Used door lock and trunk lock cylinder retainer clip. Not exactly the same as the door lock clips. Trunk clips have the small hole, a hooked tool would be used for removal. Not used on 1967 - 1968 Cougar trunk lock cylinders. *Note - For use on Cougar trunk locks built prior to 3-1-1972. Please see Ford part number D2WY-6243629-A for your Cougar needs on cars built after 3-1-1972 (used only).

Used, with little to no scratches, suitable for every day driver.

Spring steel clip located under the drive cable housing as seen on page 16, figure 19 of our free download of the sunroof panel service procedure manual.

This strip has a series of seven retaining clips that hold the headlining panel to the roof panels as seen on page 14 of the sun roof manual.

This strip has a series of five retaining clips that hold the headlining panel to the roof panels as seen on page 14 of the sun roof manual.This is for the 1971-73 Mercury Cougar with factory sunroof. Sunroof measurements are roughly 19-1/2 x 39 inches. This panel is 32-1/4 inches long with 5 clips as shown.

Replaces the original Ford part that features a # C7SB-17B732-A casting number. Basically correct for 1967 but works just as well on 1968 mirrors. These nuts are are not 100% correct for a 67 or 68, kind of a mixture of both.Very nice chrome quality at a reasonable price. NOTE: Our mirror nut removal tool works & fits perfectly with the original mirror nuts. However, you will find the tool will NOT fit this reproduction nut properly, it will require that it be filed a...

We have created all of the components needed to economically install the steel nutsert or Riv-nut for the exterior mirrors that mount to the car doors. Our steel Riv-nut uses a 1/4 inch hole. You will need a 5/32 Allen or hex key, 3/8 inch wrench, and a 7/16 inch wrench. The Riv-nut needs to be assembled on the kit as shown prior to installation. The assembly is installed flush, in the pre-drilled hole. The Allen wrench and the 7/16 are held stationary, while the 3/8 wrench is used to tighten...

Correct rivets for use after you have painted your car or installed a new door. No special tools needed for installation. Simply lightly tap the center recessed portion with a small bolt or blunt punch. If your plate is missing you can obtain a correct reproduction with your unique codes at www.martiauto.com. Sold as a pair. Replaces Ford Part #: C5ZZ-6223000-A or 354921-S.

This is the nylon roller that fits on the end of the window regulator arms. Includes rivet.Sold individually. 2 rollers required per window, 4 rollers required per car.Replaces Ford part number C5AZ-57262A32-A. Dimensions: 11/16" DiameterHere's an instructional video on how to install the rollers. Keep in mind that this is a YouTube video from Danchuk Manufacturing installing a different type roller, but the technique is the same: 1969 Glue-In Glass: The Comprehensive Repair Guide Video ...

Reproduction roof / headliner insulation kit for your Mercury Cougar or Ford Mustang. An effective item that will increase the efficiency of your heater or A/C. This will also insulate your interior from outside sounds.

Reproduction roof brace for the 67 - 68 Cougar or Mustang. This is the leading front support on your roof, directly above your windshield.

Reproduction roof repair kit that includes the roof skin, C pillars and the rear window channel for the 67 - 68 Mercury Cougar. C pillars are cut from our reproduction quarter panels. This kit must ship via truck freight. Expect to pay $400 or more to have these items shipped. Our online shipping calculator is not very accurate for truck freight items so we encourage you not to pay for the order up front but rather bypass paying for your order by selecting "contact us for...

Good used center reinforcement beam, or structural brace section for the roof skin. It does not actually attach to the roof skin. Attaches to unitized structure of the roof frame sides. Ford part number is 50222, or 6550244.

In the past, you would have had to purchase a used roof cut from a parts car which meant that you would most likely have do a bit of work to get it straight and clean enough for paint. But now our friends over at Dynacorn have finally come through with a quality reproduction roof panel skin for the 1967-68 Mercury Cougar. If you need a partial roof we can cut this part down to your specifications with a plasma cutter. The price will remain the same but if you need only a half of a roof you...

These were installed only on early production 1967 Cougars but can be installed on any 1967 Cougar. Later in the year they quit installing these and just used a rubber plug to fill the hole. 1968 was not drilled for these. Sold as a pair.

New rust treatment in aerosol form for the Mercury or Ford. Provides one-step treatment that destroys old rust and prevents new rust. Just spray it on. Within minutes, rust is replaced by a durable black polymer coating that may be painted. Excellent protective primer. Follow directions for use, wear gloves it does not wash off readily.*NOTE* This item can only be shipped via UPS ground. No Foreign orders please. ...

Good grade A used jack with correct fine threads. The most common jack as identified by the fine threads. This version was made by several suppliers, and may have slight variations from the picture. Some have date codes and some do not. Grade A will not have rust or damage.

Good used jack with correct fine threads. Notice the remnants of the original jack instruction decal. The most common jack as identified by the fine threads. This version was made by several suppliers, and may have slight variations from the picture. Some have date codes and some do not.Grade B will have Rust and or the top portion letter "M" fitting may be damaged.

Sold Individually. Chrome plated oval head screw to hold door sill plates in position. Two sill plates require 18 screws - available as a screw kit - Best value! Replaces Ford Part # 376290.

Sold individually, three per side, six per car required. These often get destroyed when you go to replace your door window regulator slides. Three of these are used to install the C7ZZ-6523288-A track. Stainless steel.Thread size: 8/32 Check out our handy diagram below to find other '67-'68 door parts you may need. All the item numbers shown can be typed in to the search bar on our site. (Click image to view full size) Not sure where to begin when it comes to replacing your window regulator?...

One kit does both rear armrests for the XR7 or Standard interior coupe.

One size fits all.  Set of 4.  Good replacement if not worried about show quality. 1967 – 1968 Coupe 6 Required per car 1969 – 1973 Coupe 4 required per car 1969 – 1973 Convertible 2 required per car Will also work on the 69 - 73 shifter bezels. 4 required. Not recommended for our Mass Backed Carpeting. Please see related items for the longer screws. Replaces Ford Part #: 381571-S

Fits all Mustangs

Sold in a set of 18 Replaces Ford # 376290

These reproduction quarter panel end seal screws fit both the Standard and XR7.

These reproduction fender shield to bumper screws fit bot the standard and XR7.

Here are our reproduction fender splash shield screws that fit 1967 Standard and XR7.

When it's time to replace your old decaying foam seal, go with our reproduction weatherstrip retainer foam roll with peel off adhesive. Goes between the roof and door / window channel.  These are not technically manufactured to fit the Cougar / Mustang, however these are very close to the originals and come from the manufacturer in a roll that is 4' X 1" X 1/8".  One roll is more than enough to do one side, but you will need 2 rolls to do both sides. ...

Seals between chrome vent frames and door on exterior side. Stops water from leaking between vent window and door. Keep in mind that this seal comes as one strip and it meant to be cut down the middle.Sold as a pair.Replaces Ford part #: C6OZ-6322280 or C6OZ-63222A80-A.

These high quality vent window seals are the first on the market to replace the original Ford part exactly. This is the small seal at the front of the door and next to the door weatherstrip. Sold as a pair. Replaces Ford Part #:C7ZZ-6522332/3

These are good reproductions of the originals for your American Sunroof Corporation Golde Sun Roof. The roof opening seal is 89 1/4" x 3/4" and the seal that affixes to the rear edge of the roof panel measures 42 1/2" x 3/4". These have the correct aluminum inner core with rubber bead, wrapped in the correct felt textured, black material. They're are made by the original manufacturer in Germany and will fit all Cougars equipped with the ASC sunroof. Very hard to find seals at a reasonable...

Premium reproduction rubber seal with the proper thickness of the 1967-68 seal as found on Mercury Cougar and Ford Mustang except these are not molded to the extension contours. Starting in 1969 this channel seal was manufactured slightly smaller which tightened up the gap on the fender and quarter extension seals. This seal maintains the slightly larger gaps. Sold as a pair, two pairs needed per car.  Each package has 2 strips of 25 1/2" lengths. *NOTE* Do not over tighten the...

Used seat belt anchor plate that has been cut out from a car in our salvage yard. Must be welded to floor pan. 6 total per car, 2 inboard in the transmission tunnel, and 4 on the rear seat pans. The front outboard anchors are part of the rocker rails. Rectangular shaped like the 1967-73 cars. We have noticed that the last generation 1971-73 Cougars had 4 round shaped plates in the rear floors. Same threads, all work the same. These were pretty much used on all Ford cars starting in...

The Cougar used a seat riser that was about one inch lower in height compared to the Mustang so as to compensate for the more plush foam and upholstery.

The Cougar used a seat riser that was about one inch lower in height compared to the Mustang so as to compensate for the more plush foam and upholstery.

This seat riser / platform is specific to Mustang, but if you're "vertically challenged"....you may want to go ahead and use this part on your Cougar. It'll raise your seat up enough so that you don't have to use phone books anymore!

This seat riser / platform is specific to Mustang, but if you're "vertically challenged"....you may want to go ahead and use this part on your Cougar. It'll raise your seat up enough so that you don't have to use phone books anymore!

Here is our free download for the 1968 Mercury Cougar sunroof panel service procedures.

Reproduction shock support for the 67 - 68 Cougar. This support sits underneath the transition hump and attaches the upper mounts of each rear shock. The shock hardware is accessible through two access holes on the hump.

If you buy this reproduction tower, you will no doubt save you time in clean up. But nothing will ever fit and look like original FoMoCo towers!Here's a little film to help you fortify your flexxy feline!

Excellent condition tower as cut from a Western parts car. No specific part number for this structural front suspension section.Generic Ford part # C7ZZ-16055-D or E, includes apron and side member.Here's a little film to help you fortify your flexxy feline! ...

We highly suggest you look at our mint condition used towers for about the same price. Why mess around with repo when you can get FoMoCo?!Here's a little film to help you fortify your flexxy feline!

Excellent condition tower as cut from a Western parts car. If you are replacing two towers because of cracks, we strongly suggest upgrading to a 1969-70 pair of reinforced towers. The 69 and 70 towers are an exact fit into your 1967-68 Ford Mustang or Mercury Cougar. There are no specific part numbers for this structural front suspension section.Generic Ford part #s C7ZZ-16054-C or C7ZZ-16054-E, includes apron and side member. Here's a little film to help you fortify your flexxy feline! ...

Used driver side shock tower and apron assembly for the Mercury Cougar or Ford Mustang.Here's our little film to help you fortify your flexxy feline!

Reproduction passenger side shock tower and apron assembly for Mercury Cougar and Ford Mustang.Here's a little film to help you fortify your flexxy feline!

Used passenger side shock tower and apron assembly for the Mercury Cougar and Ford Mustang.Here's our little film to help you fortify your flexxy feline!

Solid, undamaged driver and passenger side shock tower braces. Fits all 1967-68 Mercury Cougar and Ford Mustang. Ford part #s C5ZZ-16A053-B driver side (left hand) and C5ZZ-16A052-C passenger side (right hand). *NOTE* Excludes 1967-68 Mustang Convertible. **Installation Tip** These brackets attach under the cowl lip. ...

Shock tower coil spring cover installation hardware that fits Cougar and Mustang coupe, fastback and convertible.