Body

This driver quality manual adjust driver side mirror shows wear and the chrome will not polish out.*NOTE* Mustang uses a different mirror and will not fit contrary to what you may have seen advertised elsewhere!Hole spacing: 4 3/8"Ford part # C7WY-17696-ADo you have riv-nut questions? Here are riv-nut answers!Cougar Applications:1967 Mercury Cougar1968 Mercury Cougar ...

NOS unpackaged driver side manual adjust mirror. Shows some shelf wear, a small scuff on the base and a smudge on the glass. Don't forget to select a mounting gasket and mounting kit if needed. Casting number reads C7WB-17743-B Ford part # C7WY-17696-A. *NOTE* Mustang uses a different mirror and will not fit contrary to what you may have seen advertised elsewhere! Hole spacing: 4 3/8" Do you have riv-nut questions? Here are riv-nut answers! ...

Working grade "A" driver side (left hand) remote mirror with nice chrome. This would look right at home on a low mile unrestored car. Hole spacing: 4 3/8"Do you have riv-nut questions? Here are riv-nut answers!

Quality reproduction mirror for your 1967 Cougar. Whereas it is not easily detected at first glance, the head of the mirror does have a slightly different contour than original. The base is spot on perfect and the controller, cable assembly are all excellent quality. The wand (sold separately) is correct for 1967 (fluted, baseball bat shaped wand) as opposed to the 1968 version with a ball on the end (which we also sell). Plastic mounting pad and hardware included. *NOTE* Mustang mirrors...

Fine scratches but great for the guy who wants original. The Reproduction does not have the II-DMI-6 lettering at the bottom like this original. You will have to carefully peel (roll back) the aluminum backing that is glued in place before gluing it in your mirror. If you use needle nose pliers and take your time it usually works fine. Note that the pictures of our 67-68 mirrors and lens can be deceiving. This is a tapered mirror, the narrow end faces upward on a Cougar, it is reversed when...

If your are missing your factory Riv-Nuts, or you are installing a passenger side mirror, these are a very easy to use alternative to the metal riv-nuts we offer. Another good application for these is when your existing mirror mounting holes are "hogged out" these slightly over sized inserts are just the ticket. Keep in mind our kit is not only less money than others you may find but the screws are stainless steel. Hole size for these rubber inserts is 3/8". Keep in mind the upper lip stands a...

New old stock, This unit is also known as a bumper filler, rock guard, or filler panel. Fits any 1967-68 Mercury Cougar.Ford part # C7WY-17779-A.

Used driver side (left hand) sunroof cable for the Mercury Cougar. We have a really hard time keeping these units in stock. Keep in mind this same basic cable design was used on many makes including Porsche, BMW, Mercedes and several other cars through the early 1980's. The same basic design (minor changes through the years) was used on Lincolns, Thunderbirds and other Ford products through the mid seventies. We are buyers of used sunroof cables, motors and misc parts so keep us in mind you...

Used passenger side (right hand) sunroof cable for the Mercury Cougar. We have a really hard time keeping these units in stock. Keep in mind this same basic cable design was used on many makes including Porsche, BMW, Mercedes and several other cars through the early 1980's. The same basic design (minor changes through the years) was used on Lincolns, Thunderbirds and other Ford products through the mid seventies. We are buyers of used sunroof cables, motors and misc parts so keep us in mind...

1967 Cougar Owners: To view our exploded view interactive diagram of the tilt steering column parts, click here. NOS new old stock door jamb switch to release tilt/tilt-away columns on a 67, 68 or 69 Mercury Cougar or Ford Mustang. Here is an excerpt from the 1967 owners manual: The wheel will swing to the right and up towards the instrument panel whenever the driver opens his door, provided the ignition switch is turned off. When re-entering the vehicle on the drivers side, pull the...

This tiny little spring has a diameter no larger than a pencil. Its function is to attach the deck lock cover to the deck lock housing and to keep the deck lock cover closed. This is a unique spring to this application and rather hard to find.Check out our video below showing how to easily remove and reinstall your 67-68 trunk latch, lock, and cover plate, and some info on getting a new key made. ...

This is an upgraded version from what you see in our video but the idea is the same. This tool has a square hole so you can use your 3/8" drive ratchet or breaker bar to get the correct angle and have even better control of your leverage when placing the torsion bar into the slot. Used to remove the hinge springs (torsion rods) off the 1967 - 1973 Cougar or Mustang. No more trying to remove with the wrong tools . These can be tricky to remove without this tool.  Will not work on 1964 -...

Reproduction passenger side (right hand) torque box for Mercury Cougar and Ford Mustang convertibles.Here's our little film to help you fortify your flexxy feline!

Here is our reproduction SPI torque box for the driver side (left hand) of your Mercury Cougar coupe.

Here is our reproduction passenger side (right hand) SPI torque box for your Mercury Cougar coupe.

Reproduction passenger side (right hand) torque box outer section for Mercury Cougar and Ford Mustang coupe and convertible.Here's our little film to help you fortify your flexxy feline!

NOTE: We've been getting reports that these reproduction torsion bars lose their tension after a few weeks and will no longer lift the deck lid. These reproduction rods are installed horizontally in your trunk and attach to the trunk lid hinges.  Replaces Ford part numbers C7WY-6544890-A and C7WY-44891-A. The body section of the shop manuals describe how to adjust these bars, we offer a torsion bar adjusting tool for this purpose. *Note - Does not fit Mustang. Check out our...

Used driver side (right hand) spring from a door latch assembly fits many Ford and Mercury cars. This will fit all years 1967-70. 

Used passenger side (right hand) spring from a door latch assembly fits many Ford and Mercury cars. This will fit all years 1967-70. 

These reproduction J clips mount to the underside of the deck lid and fit Standard and XR7 trunk lids.

Good used, rust free valance with minor amounts of filler, dings and creases. These are not paint ready flawless parts, but rather 40 years old and taken from a parts car. Unless you have body work skills these are not a good value considering the amount of work needed to make them paint ready. We are very happy with the repro front valance we sell.Ford part # C7WY-17620-A. ...

Good used, rust free valance that will have minimal prep time to be paint ready. Getting to be hard to find without excessive filler. If you have the optional rear bumper guards then you will want a valance like the one pictured that has the factory holes for them. These are not paint ready, flawless parts but rather 40 years old, taken from a parts car. Ford part # C7WY-6540544-A.

Good used, rust free valance for the 67 - 68 XR7G Cougar that will have minimal prep time to be paint ready. Getting to be hard to find without excessive filler. If you have the optional rear bumper guards then you will want a valance like the one pictured that has the factory holes for them. These are not paint ready, flawless parts but rather 40 years old, taken from a parts car. Ford part # C7WY-6540544-A.

Decent used, rust free valance that will need work done. Getting to be hard to find without excessive filler. These are not paint ready, flawless parts but rather 40 years old, taken from a parts car that will have small dents, creases and often some amount of filler. The current reproduction rear valances (unlike the front) do not fit very well.Ford part # C7WY-6540544-A.

We have a very hard time keeping these NOS rear lower valences in stock. Since the reproductions don't quite fit right, NOS and good used are the best options at this time.Ford part # C7WY-6540544-A. This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of 50% of our web price for parts delivered in hand or by carrier to our Brooks, Oregon location. If you're not interested in store...

Good used, rust free valance with provisions for rear bumper guards. Getting to be hard to find without excessive filler. We have a local body man take out the small dents and he does not load them up with Bondo. He removes the filler and works the dent out properly. If you have the optional rear bumper guards then you will want a valance like the one pictured that has the factory holes for them. These are not paint ready, flawless parts but rather 40 years old, taken from a parts car. We do...

Decent used, rust free valance that will need substantial work. Getting to be hard to find without excessive filler. These are not paint ready, flawless parts but rather 40 years old, taken from a parts car that will have small dents, creases and often some amount of filler. We do have NOS and on occasion we get in a flawless used example.Ford part # C7WY-6540544-A.

New Old Stock passenger side (right hand) vent / wing window handle for the 1967 Mercury Cougar or Ford Mustang. Also fits 1966 Ford and Mercury mid sized cars. Ford part number C6OZ-6222916-A.

High quality reproduction black vinyl top for the Mercury Cougar that features both the correct pattern and finish. This concours correct top also features a durable moisture resistant backing that will look better and last longer than any economy priced version. Thinking about installing this unit yourself? Check out our video below for some inspiration. ...

This threaded replacement wand will require you to cut 8/32" fine threads in your original controller. Your OEM mirror controller is made of a very soft metal so one can often install these as "self tapping".1967 and 1968 are different, see comparison picture. The 1968 version was rounded off due to new safety standards. The mirror nut tool will fit over the 1967 wand, but not the 1968.

This product has received the 'Crappy Product' certificate. Items that receive the 'Crappy Product' certificate are products that we carry for comparison purposes as they are often the version offered by other vendors or because it is the only version available. We would not be willing to use these parts on our own cars, and we do not recommend purchasing these parts. WE ARE NOT ABLE TO ACCEPT RETURNS FOR THESE PARTS. Economy replacement vinyl top that looks great and fits perfect. This...

Good used crank correct for 1967 XR7 or standard models. No obvious blemishes, driver quality. The Ford part # is C5ZZ-6523342-C, casting number as found on the back reads C7ZB-6523348-A. *Customer Feedback* Don, Lin and staff; Just to let you gentlemen know that I have received the 1967 XR7 saddle tan door panels you sent and I am extremely happy with the condition and the service! It has been less than a week since I ordered them and they arrived via USPS, as per requested, with a very...

1967 was the last year for the 3/8"-16 threads. We also carry the J bolt C6OZ-1448-A, and the top plate or disc C5ZZ-1424-A. Wing-nut, spinner. *NOTE* The original 67 wing nut had no protruding tabs in the recessed area as did most of the 1968 - 1973 wing nuts.

Used wrench or crank, for manually closing the factory installed sunroof installed on any 1967-73 Mercury Cougar. Sunroofs, technically moonroofs, were originally installed by ASC or American Sunroof Corporation. Hertz 1968 XR7-G cars all came with factory sunroofs, as did the Hertz rental 1969-70 Cougar Eliminators. ASC also installed sunroofs in Ford Thunderbird, Lincoln MK III.ASC used Golde mechanical parts from Germany. Golde was a manufacturer of sliding canvas and metal roofs on...