Body

Steel plate for mounting the door pull or grab handle on 1967-68 Mercury Cougar XR7. Right and left is dependent upon which way the nylon inserts are installed. Comes complete as shown with nylon inserts for attaching the door pulls. The screws with 1/2 inch flat head for mounting this plate to the doors are also a available (three required).

Used mounting bracket for the sunroof motor on the 67 - 70 Mercury Cougar. This bracket is only used with the 67 - 70 power sunroof motor.

Reproduction mounting bracket / retainer for the XR7G headlight eyelid emblem. The emblem will attach to this bracket with double sided tape or epoxy, whichever you choose. Emblem and 3/8" 10/24 nuts not included.

Spare tire, with styled steel wheel hold down disc. Fits all 1968-70 Mercury Cougar and Ford Mustang. Original Ford part number C8MY-1424-A. About 3 inches in diameter, this is the specified trunk hold down plate for the use with the factory mag wheels.

4" mounting Plate for Standard Spare Tire. Replaces Ford Part #: C5ZZ-1424-A.

3 1/8" Style Steel Wheel Spare Tire Hold Down. Available in Black or Chrome. Ford Master Parts Catalog indicates that this hold down was found on some 68 and 69 Cougars with SS Wheels. You may need to bend the ears in slightly to get them to fit properly inside the hole in the center of the wheel. Replaces Ford Part #: C8MY-1424-A.

Correct looking mounting plates used to mount the 1970 original spoilers. Comes with all hardware shown, not intended for 1969 spoilers as the use of these requires large rectangular holes, found only on 1970 of the bottom side of the deck lid.

Reproduction side view mirror screw. These screws are sold individually. Do you have riv-nut questions? Here are riv-nut answers!

These spacers are required to properly mount the trunk lock housing to the trunk. Two required per car, sold individually. Ford part number C7WY-6543565-A. Check out our video below showing how to easily remove and reinstall your 67-68 trunk latch, lock, and cover plate, and some info on getting a new key made. ...

These spacers are required to properly mount the trunk lock housing to the trunk lid.  Sold as a pair. Replaces Ford part number C7WY-6543565-A. Follow this link to find the lock housing nuts. Check out our video below showing how to easily remove and reinstall your 67-68 trunk latch, lock, and cover plate, and some info on getting a new key made. ...

10 of these are used to mount the 1968-71 Cougar hood scoop found on the 68 428 CJ, 1969-70 Eliminator, 1969-70 428 Ram Air equipped Cougars, and 1971 GT and 429CJ. Sold individually Zinc (dark silver).

This is our reproduction quarter panel extension nut for the Mercury Cougar or Ford Mustang. These are sold individually.Replaces Ford part # 373556-S. Fits: 1967 Mercury Cougar1968 Mercury Cougar1969 Mercury Cougar1970 Mercury Cougar 1967 Ford Mustang1968 Ford Mustang1969 Ford Mustang1970 Ford Mustang ...

New O-ring gasket for the 1967-68 Mercury Cougar flip trunk lock cylinder. Lock cylinder must be removed from the trunk lock housing to install. Original O-rings are normally cracked and broken when we disassemble them. 

Here is a free download for the operating instructions for the sunroof panel on the 1968 Mercury Cougar.

Full driver (left hand) side front frame rail measures 52" long and the outer rail has weld nuts installed for proper installation.

This listing is for the outer wheel house on a 1967 or 1968. Often when you replace the skin you will find multiple soft spots in the outer wheel house, especially down low. If you do not want to pay the oversized shipping on these large items we do sell patch panels.We also sell these as a complete set of four, which will save you money on shipping as we unbox them and nest all four together and fit them in one box. ...

This listing is for the outer wheel house on a 1967 or 1968. Often when you replace the skin you will find multiple soft spots in the outer wheel house, especially down low. If you do not want to pay the oversized shipping on these large items we do sell patch panels.We also sell these as a complete set of four, which will save you money on shipping as we unbox them and nest all four together and fit them in one box. ...

This listing is for the outer wheel house upper patch for the driver side of your 67-68. 

This listing is for the outer upper wheel house patch for the passenger side of your 67-68.  

This listing is for outer wheel house lower patches, front and rear for the driver side of your 67-68. There is no cost savings on the purchase price, but often people only need the lower section and shipping these (especially overseas) can be cost prohibitive. Since we cut these in house you can request where we cut if you would like a custom cut different than what is pictured here.

This listing is for outer wheel house lower patches, front and rear for the passenger side of your 67-68. There is no cost savings on the purchase price, but often people only need the lower section and shipping these (especially overseas) can be cost prohibitive. Since we cut these in house you can request where we cut if you would like a custom cut different than what is pictured here.

New reproduction 1968 XR7 Overhead console warning light bar. Unlike 1967 XR7, 1968 features a woodgrain overlay and white lettering painted on the surface of each lens. Ever noticed how the originals have a chunk of vacuum hose wedged behind the mounting tabs? That is because the originals used the wrong grade of steel and the soft metal tabs would not hold them in place without help. We fixed that by using the correct quality of steel.

New product that is in stock and ready to ship! Unlike 1968 the 1967 xr7 console indicator light bar had no woodgrain applique. This will work fine on your 68 and some prefer the 1967 look over the 1968 version. We have a few of these with a 1968 Burl Wood Overlay applied to them. If you would like one of these, mention it in the order notes and if we have any remaining will send you one of these. These two pictures give you an idea what the lights will look like when illuminated. When not lit...

These decals are cut to fit the 1968 end caps. The 1967 end caps had a larger woodgrain insert without a black border. We also sell a slightly larger version of this kit for the 1967 owners. Simple peel-and-stick installation. Here’s a little inspiration for you to get our vinyl overlay kit and wrap your own parts! ...

Wow! Almost nothing is 100% correct about these rear package trays... No, your monitor is not out of adjustment, these colors are truly wrong except for the black. A couple of the colors are "close" to original but most will have to be repainted if you are concerned about correctness. The mesh is much lighter weight than the original and the speaker holes are not exact but the fit is good and overall this is a durable attractive piece. NOTE: Package Tray has a perforation you have to bend on...

Wow! Almost nothing is 100% correct about these rear package trays... No, your monitor is not out of adjustment, these colors are truly wrong except for the black. A couple of the colors are "close" to original but most will have to be repainted if you are concerned about correctness. The mesh is much lighter weight than the original and the speaker holes are not exact but the fit is good and overall this is a durable attractive piece. NOTE: Package Tray has a perforation you have to bend on...

Wow! Almost nothing is 100% correct about these rear package trays... No, your monitor is not out of adjustment, these colors are truly wrong except for the black. A couple of the colors are "close" to original but most will have to be repainted if you are concerned about correctness. The mesh is much lighter weight than the original and the speaker holes are not exact but the fit is good and overall this is a durable attractive piece. If you buy the insulation pad that lies beneath this panel...

Wow! Almost nothing is 100% correct about these rear package trays... No, your monitor is not out of adjustment, these colors are truly wrong except for the black. A couple of the colors are "close" to original but most will have to be repainted if you are concerned about correctness. The mesh is much lighter weight than the original and the speaker holes are not exact but the fit is good and overall this is a durable attractive piece. NOTE: Package Tray has a perforation you have to bend on...

Wow! Almost nothing is 100% correct about these rear package trays... No, your monitor is not out of adjustment, these colors are truly wrong except for the black. A couple of the colors are "close" to original but most will have to be repainted if you are concerned about correctness. The mesh is much lighter weight than the original and the speaker holes are not exact but the fit is good and overall this is a durable attractive piece. NOTE: Package Tray has a perforation you have to bend on...

Wow! Almost nothing is 100% correct about these rear package trays... No, your monitor is not out of adjustment, these colors are truly wrong except for the black. A couple of the colors are "close" to original but most will have to be repainted if you are concerned about correctness. The mesh is much lighter weight than the original and the speaker holes are not exact but the fit is good and overall this is a durable attractive piece. If you buy the insulation pad that lies beneath this panel...

Wow! Almost nothing is 100% correct about these rear package trays... No, your monitor is not out of adjustment, these colors are truly wrong except for the black. A couple of the colors are "close" to original but most will have to be repainted if you are concerned about correctness. The mesh is much lighter weight than the original and the speaker holes are not exact but the fit is good and overall this is a durable attractive piece. NOTE: Package Tray has a perforation you have to bend on...

These fasteners were used to keep your package tray in place. In 1969 - 1970 the two clips were held in place with screws. Sold individually. We have seen various tech type screw with both large and small heads on them for fastening these clips. Same clip as was used in 1967-68, but without the push clip. We try to supply the screw, but you would likely want to get fresh ones, they are nothing special.Replaces Ford part number C4AB-6246698-A.

These fasteners were used to keep your package tray in place. In 1971 - 1973 three clips were used, held in place with screws. Sold individually.

Reproduction mastic sound deadener for the package tray on your 1967 Mercury Cougar. 

Reproduction mastic sound deadener for the package tray on your 1968 Mercury Cougar.

If losing weight in your 1969 - 1970 Coupe is what you are after then this would be a good part for you as it weighs less than one pound and the original weighs approximately five pounds. The original is made of the same material as the sound deadener found under the carpet and we rarely get good examples in stock.

Great for those wishing to shed a few pounds from their early Cougar as this insulation weighs less than one pound and the original weighed almost four pounds. If you want to keep your Cougar original then you will want to check out our used package tray sound deadener / insulation / jute. *NOTE* This is actually patterned for a 1968 Cougar, but will work in a 1967.

These fasteners were used to keep your package tray in place. In 1967 - 1968 two T shaped fasteners were held in place with a spring clip. Sold individually. Ford part number C4AB-6246698-A

Reproduction cover board for the rear package tray found on the 1967 Mercury Cougar behind the rear seat, visible through the rear window. The 1967 tray is deeper as it installs over the tops of the rear side panels. In 1968 they installed under the rear vinyl covered panels. The difference between the WCCC panels and the others on the market is that we run them through a drum sander so as to give the textured side a more muted look and feel than unsanded masonite board. The other brands do...

WE CAN NOT SHIP THIS PRODUCT INTERNATIONALLY WITHOUT SHIPPING IT AS HAZARDOUS MATERIAL. THIS WILL INCUR HAZARDOUS MATERIAL CHARGES VIA UPS AND SOME COUNTRIES DO NOT ACCEPT IMPORTING THIS PRODUCT. This ORR LAC chassis black paint will give the appearance of an expensive, baked on finish. Also usable on other tools, equipment, vehicle frames, shop racks, trailers and more. ORR-LAC 923 Semi Gloss black.

WE CAN NOT SHIP THIS PRODUCT INTERNATIONALLY WITHOUT SHIPPING IT AS HAZARDOUS MATERIAL. THIS WILL INCUR HAZARDOUS MATERIAL CHARGES VIA UPS AND SOME COUNTRIES DO NOT ACCEPT IMPORTING THIS PRODUCT.This VHT roll bar and chassis paint will give the appearance of an expensive, baked on finish. Heat resistant to 250 degrees, this epoxy coating also resists chemicals, rust, corrosion and salt. No primer is needed. Also usable on other tools, equipment, vehicle frames, shop racks, trailers and more. ...

VHT epoxy paint is great for a number of applications. It's a unique one step protective coating that dries quickly and doesn't require a primer. It provides excellent rust, corrosion and chemical resistance which, needless to say, is ideal for anything you're doing under your hood or under and around the body of your car. One can covers about 12 - 14 square feet.

WE CAN NOT SHIP THIS PRODUCT INTERNATIONALLY WITHOUT SHIPPING IT AS HAZARDOUS MATERIAL. THIS WILL INCUR HAZARDOUS MATERIAL CHARGES VIA UPS AND SOME COUNTRIES DO NOT ACCEPT IMPORTING THIS PRODUCT. SEM brand COLOR COAT paint is formulated to match, restore or change color on most vinyl surfaces, flexible and rigid plastics, carpet and velour. COLOR COAT is fade resistant, flexible and is a semi-permanent coating. We do not recommend this product for driver side arm rests, door pull straps, shift...

WE CAN NOT SHIP THIS PRODUCT INTERNATIONALLY WITHOUT SHIPPING IT AS HAZARDOUS MATERIAL. THIS WILL INCUR HAZARDOUS MATERIAL CHARGES VIA UPS AND SOME COUNTRIES DO NOT ACCEPT IMPORTING THIS PRODUCT. This is a GOOD match for 1967-68 Cougar parchement / off-white interiors. SEM brand COLOR COAT is formulated to match, restore or change color on most vinyl surfaces, flexible and rigid plastics, carpet and velour. COLOR COAT is fade resistant, flexible and is a semi-permanent coating. We do not...

This charcoal black aerosol paint is a very close match to the original finish used on 1967-68 Cougar XR-7 lower dash structures and steering columns. We've tried it ourselves and have been satisfied with the results. Our only critique is that it's a bit slower to dry than other paints we're used to. The AccuMatch(TM) Interior Paints are the result of years of work and perfectly match the original color shades. Each color has been expertly color-matched. Paints feature extra-high pigment...

Professional grade paintless dent removal kit. This kit is designed to work with smaller blemishes such as dents from hail, door dings, etc. Complete with universal high strength glue sticks, puller, and a variety of different sized gluing tabs. NOTE: Remove glue with 91% alcoholAlthough we work with 67 - 73 Cougars and Mustangs, this kit is good for a wide variety of different vehicles.

Pan head screw for attaching the sport mirror glass assembly into the passenger side painted sport mirror head. Found on all FoMoCo products utilizing a manual mirror 1969 - 1973. 8-32 pan head screw with Phillips screw head. Do you have questions about installing a passenger side mirror or using Riv-Nuts? ...

Reproduction anti rattler board - 1/8" panel board that prevents rattling noise. Installs on top of fuel tank on the side where the jack and spare tire mount.Measures 12" X 6"