Engine & Under Hood

A needed part for giving your car a tune-up. PCV Valve fits all years; 289, 302, 351, 390, and 428 CID; V8. *Note - Not technically correct for 390-4V or 428CJ, those originally used a PCV valve with a threaded top, and the 90° elbow - part number C7OZ-6A706-A.

Powerful oil filled coil that generates 40,000 volts, designed to work with the either of our Pertronix Ignitors. Sold in black or chrome. *Note - This coil is not necessarily needed with the Pertronix Ignitors, the stock Ford coil works fine for most applications.

Reproduction Exhaust Manifold Pipe Stud Kit for the 260, 289, 302, 351 and 1969 390GT 1967 - 1972 Mercury Cougar and Ford Mustang

Kit has the longer studs for use with spacers or butterfly spacers, between 390 and 428CJ passenger side exhaust manifolds and H pipe flange.

Used cover plate or thrust plate that retains the camshaft on the front of Ford V-8 engines such as 351C, 351M, 400, 429, 429CJ, and 460. 1970-76 Mercury Cougar or 1968-76 Ford anything. We have found a Ford number of C8SZ-6269-A. 

Used air cleaner base plug, plugs the area pre cut from the factory. Typically found on 70 - 73 Cougar and Mustang.

Brass screw in plug for select Autolite distributor vacuum advance units from 1968-71, typically the banded single advance units factory installed. Solid brass, originals were not, we believe that they were cadmium plated. Solid plug, should be hollow, with a 3/4 inch hex head. Works as it should. Fits most all vacuum advance that have a plug in the end as shown. *Note, when removing the old plug, there is a spring and washer inside. 

Used power steering oil cooler for many 1971-73 Ford, Lincoln and Mercury cars with air conditioning. Specifically these came from 1971-73 Mercury Cougar or Ford Mustangs with factory installed air conditioning and power steering. This unit mounts to the top of the A/C compressor. This installs inline with the low pressure return hose.  Manufactured by the Blissfield Company and has a Ford stamped number of D1AA-3D746-AB. The Ford engineering number is D1AZ-3D746-D. 

Aluminum Preheater hose that is used to preheat carburetor air. This 2" X 18" aluminum flex / stretch type hose attaches from the exhaust manifold shroud to the bottom of your air cleaner snorkel.  This hose is sold individually and does not come with clamps.If you prefer, you can grab the cloth type hose here.  ...

Reproduction alternator pulley, single sheave. Fits 1967-73 Mercury Cougar and 1965-73 Ford Mustang and most all other 1965-73 Ford vehicles.

Reproduction alternator pulley, two sheave. Fits 1967-73 Mercury Cougar and 1965-73 Ford Mustang and most all other 1965-73 Ford vehicles.

Has casting number D0OE-6312-B stamped on the inside. Application for 1970 all 351 engines, 1971 M code 351-4V, and 1971 and 1972 H code 351-2V engines with power steering or idler pulley. Dual sheave crankshaft pulley measurement of 8.00" and 6-11/16" diameters. No air conditioning. Ford Master Part number D0OZ-6A312-E. Four bolts hold it on too.

Single sheave crankshaft pulley. No options, one single fan belt around the crank shaft pulley, water pump pulley, and the alternator. Probably found on Boss 351, and other 351C cars without power steering or air conditioning.Pulley marked D1ZE-6312-AA.

D0OE-6312-A For both Windsor and Cleveland 351 engines starting in 1970. This is a single sheave pulley, meaning without air conditioning and without power steering. One groove with a diameter of 6-11/16 inches in diameter. Ford Master Part number D0OZ-6A312-A. A four bolt hole crankshaft pulley for use with 1970 and upward crank dampeners.

D0AE-6312-C For both the Cleveland and Windsor variety. Starting in 1970 Ford tried to standardize many of the engine parts. This is the "with air conditioning" pulley for all 1970 - 1971 351-2V & 351C-4V engines, and all 1972 -1973 351-2V engines. Triple sheave 6-23/32", 8.00", 8-13/32" inch diameters. A four bolt hole crank shaft pulley for use with 1970 and upward crank dampeners. Ford Master Part number D0AZ-6A312-C. *Excludes 1972 and 1973 Q code 351CJ engines. This means all 1972 and...

Applications, 1970 - 1971 - 1972 351c engines, All with or without air conditioning. Casting number D0OR-B. 6-1/4" diameter and 7/16" sheave width.

Applications, 1970 351w engines, 1971 429CJ engines, and 1973 351c engines. All with or without air conditioning. Casting number D0AR-A. 5-3/4" diameter and 7/16" sheave width.

Applications various 302 / 351/ 429 engines. All with or without air conditioning. Casting number D0AR-B. 5-13/32" diameter and 7/16" sheave width.Ford part number C9TZ-3A733-D.

Used water pump pulley used on 1970-73 Mercury Cougar and Ford Mustang with 351 engines and air conditioning. This pulley is 5-15/16 inches in diameter. Pulley stamped C9OE-8509-F.

Single sheave pulley 5-15/16 inches in diameter. When measured from the front of the water pump hub (or inside of the pulley) to the center line of the belt sheave the measurement is 2-5/16 inches.Application:1971 - 1973 351 engines with power steering and A/C. Ford casting number D1AE-8509-AA.Ford Part Number C9OZ-8509-C or D2OZ-8509-A

Single sheave pulley 6-61/64 inches in diameter. This pulley is designed to run on the inner most belt plane next to the water pump. When measured from the front of the water pump hub (or inside of the pulley) to the center line of the belt sheave the measurement is 2-5/16 inches. Applications:1970 Boss 302 Eliminators with power steering**1970 351 with power steering**1971 - 1973 351 engines with power steering or with idler pulley without air conditioning* Ford casting number D1AE-8509-BA....

Single sheave pulley 6-61/64 inches in diameter. When measured from the front of the water pump hub (or inside of the pulley) to the center line of the belt sheave the measurement is 2-5/16 inches. Applications:1970 Boss 302 Eliminators with power steering**1970 351 with power steering**1971 - 1973 351 engines with power steering or with idler pulley without air conditioning* Ford casting number C9OE-8509-G.  Ford part number C9OZ-8509-D Note:  * The Master Parts...

Usually ships in 3-5 business days. Reproduction direct fit OE style 3 row MaxCore radiator, designed for optimal performance with increased tube size and amount of fins. Our supplier uses higher copper purity for long lasting durability and heat transfer.

New old stock Chrome radiator cap. Motorcraft stamped, with RS-512A, and 13# Pound rating is stamped on cap. Replaces Ford Part #: C9ZZ-8100-A.

Keeps the corrosive agent in your coolant from destroying vital engine components

These concours quality Zinc caps are made in America and bear all the original markings. O.E.M. details include original letter style, "S.M.C.O." and "Autolite". Pound rating is stamped on cap. Replaces Ford Part #: C7ZZ-8100-A.

These concours quality Zinc caps are made in America and bear all the original markings. O.E.M. details include original letter style, "S.M.C.O." and "Autolite". Pound rating is stamped on cap.

New old stock Zinc radiator cap. Motorcraft stamped, with RS 12A, and 13# Pound rating is stamped on cap. Replaces Ford Part #: C9AZ-8100-A.

These are O.E.M. replacements and will not fit most after market radiators.

Four needed per fan shroud. Sold individually.Ford Part Number: 383152-S

Reproduction plastic upper radiator seal for 1971-73 Mercury Cougar and Ford Mustang. Also called a radiator air deflector.  There are 2 versions of this deflector for different depth radiators. This is the larger version (smaller version is not reproduced) and can be cut down to work on cars with narrower radiators.  Some cars used clips to hold these on, but most used staples. Also fits 1970-71 Torino, Ranchero, Cyclone and Montego. As well as 1970-72 full sized Ford and...

Air conditioning bearing replacement service. Send your flat bearing style, fixed or adjustable A/C pulley and we will exchange it or rebuild your exact pulley with a new flat bearing. Either large or small flat bearings, same price.  Dust caps hand fitted, for seamless installation. No extra tool marks, other than the factory peening. Check photos.Ford casting #'s D0AA-8A617-B, D0AZ-8678-D, C8AZ-8678-B, C8AZ-8678-C, C8AZ-8678-A, D8OH-19W653-A, D0AZ-8678-D.*Note* All new bearings will...

These Spark Plug Wire Separators are made of high-quality ABS plastic. Constructed to hold both standard 7mm and 8mm high-performance spark plug wires. Fits directly on valve cover clip. Available in blue, red and OE black.

This is a good quality non-concours starter solenoid. Inexpensive replacement if you are not worried about being 100% correct. Disappointing quality, often will fail in less than a year, we recommend buying original FoMoCo. Replaces Ford part # B6AZ-11450-A, C7AZ-11450-A & D2AF-11450-A.

Original retainer that clips onto the breather element nipple sticking through the air cleaner base and holds the elbow for the hose going to the PCV valve.  Ford calls this part the Crankcase Emissions Filter Retainer.The Master Parts Catalog says this part is only for 1971 and newer cars, but this part has been found on low mile 1970 cars as well. Ford part # D1AZ-9E628-A.

Replaces Ford Part Number: B7A-12200-A / DR-5 And C5TZ-12200-A / DR-87 (Service Replacement)

New slotted pan head screw for mounting distributor points or condensers. Three total, per single advance Ford distributors. We know that these fit FoMoCo, Autolite and Motorcraft marked distributors 1967-73. These are AMK screws 8-32x9/32". Sold individually, but you likely need 3. 

New phosphate dipped slotted pan head screw for mounting distributor vacuum advances. Two total, per Ford distributor. We know that these fit FoMoCo, Autolite and Motorcraft marked distributors 1967-73. These are AMK screws 8-32x1". Sold individually, you will need 2. 

Reproduction black Holley "Sniper" fuel injection conversion carburetor for the 67 - 73 Cougar or Mustang. Upgraded Sniper II also now available! Dual Pattern bolt on carburetor replacement, designed to fit 4150 Flange & Spread Bore manifolds - (Spread Bore Sealing Plate Part #9006 is recommended)Throttle body mounted ECU – no extra boxes to mountSupports up to 650hp with Four 100 Lb/Hr InjectorsOnly 4 Wiring Connections Required! (Battery +, Battery - , Switched Ignition & RPM)Includes...

The #1 EFI conversion system just got better! Introducing Sniper 2 EFI - a self-tuning, easy-to-install, EFI conversion for common 4-barrel (4150 flange) style carburetors. Holley took everything that they learned from the original Sniper EFI system and added 14 new features that will make your EFI conversion more simple, reliable, and modern. Like all Sniper EFI systems, Sniper 2 is designed to work with the Sniper Ecosystem that includes Hyperspark ignition, complete fuel systems, multiple...

Application is for all 1971 Cougars with 351 engines, both 2V and 4V engines. Additionally it includes 1972 351-4V without NOx. Our research shows that NOx was a California emissions requirement. Ford part number D10Z-9A626-B. *Note - 1972 49 state 351-4V air cleaner snorkel.

Application would be for only 1971 Cougars with the 429CJ option, either ram air or non-ram air. Original Ford part number was D0GY-9A626-A, this unit is from a Ford Truck, part #is from a D3TZ-9A626-G. This is a low cost alternative to a very rare part. Click on images to enlarge. ...

Air cleaner pre-heater paper hose. Should fit most applications from 1970-73 Mercury Cougar and Ford Mustang with V8 engines. 2 inch inside diameter, we cut these to about 9 inches long. Correct black paper outside, flexible paper tube, kind of like a Slinky. Please verify your needed length, we leave them a bit longer than needed so that they fit more than one application.

Alternator spacer bracket for all 351 engines. 1970-73 Mercury Cougar and Ford Mustang among others such as Torino, Cyclone, Galaxie, LTD, etc. Aluminum material, 2-1/4 inches long, with a 7/16" hole. Sometimes solid and sometimes open along the side. Ford part number D0OZ-10A370-A.

Aluminum spacer for mounting the alternator on 1971 Mercury Cougar and Ford Mustang with 429 Cobra Jet engines. Also fits 1970-71 Cyclone and Torino with 429CJ engines. Spacer measures approximately 1-1/16 inches long. Fits between the cylinder head and alternator housing.

Used alternator fan spacer for the 1967 - 1973 Mercury Cougar or Ford Mustang.  This spacer also fits many other Ford applications.  Ford part number: C5AZ-10A344-B.

Reproduction 384543-S8 Power steering pump adjusting spacer for use without air conditioning. For most 1970 - 1973 Mercury Cougar or Ford Mustang with 351C engines. Spacer dimensions: 7/16" I.D. and 1/2" thick.*Note 1970 and later cars with 302 or 351W engines use a 3/4 inch spacer.

Correct Autolite 24 spark plugs for all 1970-73 351 Cleveland engines. This is what Ford installed originally from the factory. Typically these should have a electrode gap of 0.035", with either stock points or Pertronix ignition systems. Sold individually.