Engine & Under Hood

C9OZ-6A664-A Original used hose that connects the original PCV valve to the carburetor spacer plate. All 1969-70 351 Windsor 2V and 1969 351Windsor 4V engines. Used hoses will have faded striping (if present), and clamp impressions. Very often the rubber will be hard and showing some degree of stress cracks. This hose is a bit longer than the 289/302 version due to the taller deck height of the 351 Windsor engines. *Note - These molded and contoured hoses were designed to work with the...

C7TZ-6A664-A Used after 02-21-1969. Original used hose that connects the original PCV valve to the carburetor spacer plate. All later 1969 S code 390-4V engines. Used hoses will have faded striping (if present), and clamp impressions. Very often the rubber will be hard and showing some degree of stress cracks. *NOTE* These molded and contoured hoses were designed to work with original style PCV valve (modern 90° PCV valves won't work). Additionally anything other than period original intake...

Used vacuum hose with inline muffler, connects the Servo Valve to the Regulator on 1969 Mercury Cougar and Ford Mustang with factory Speed Control. Hose about 42.7509 inches long. Ford number for hoses is C9ZZ-9D860-A.

New old stock bracket and pulley assembly for Cougars or Mustangs equipped with the 289, 302, or 1969 351W engine. We also offer a bearing replacement service to rebuild your 289, 302, or 1969 351W fixed idler pulley, see item 27539. Ford part # C8AZ-8678-C. ...

Used fixed idler bracket and pulley assembly with new installed bearing for 1968-69 Cougars and Mustangs with the 390 or 428CJ engine. This part will have a small bearing on the pulley and is not marked with a casting number. The 1970 bracket and pulley assembly was a service replacement part and are the same as the 68-69 with the exception of a slightly larger bearing. This later service replacement part is an economically priced service replacement for the earlier originals. All pulleys come...

C8OZ-3C511-B Rear power steering pump support bracket. Also called the high pressure hose indexing bracket. For any 1968 - 1970 Cougar or Mustang with any of the 390 / 427 / 428CJ engines. OEM used part designed to maintain the position of the high pressure power steering hose from coming in contact with with moving or high heat parts. *Note - May or may not work with non-original or replacement high pressure hoses.

C9ZE-9425-A or -B Cast iron intake manifold used on all S code 390-4V engines in a Mercury Cougar or Ford Mustang. Stock 4 barrel intake manifold. Take off manifold with correct casting number of C9ZE-9425-A or -B. Intake shipped bare, less carburetor studs, heater tube, vacuum fittings, and water neck where applicable. Ford master part number C9ZZ-9424-A. Current date 8H14.*Installation Tip - A water heated aluminum spacer plate with PCV provision is needed for proper air cleaner clearance....

C9ZE-9425-D or C9ZE-9425-E Cast aluminum intake manifold used on all 1969 G code Boss 302 engines in a Mercury Cougar Eliminator or Ford Mustang. Stock 4 barrel intake manifold. Take off manifold with correct casting number of C9ZE-9425-D or -E . Intake shipped bare, less carburetor studs, heater tube, vacuum fittings, and water neck where applicable. Ford master part number C9ZZ-9424-C. Has "Buddy Bar" cast into the bottom side.

Cast aluminum Sidewinder intake manifold. Over the counter speed part for the 427 Medium Riser. The offset carburetor placement was to help provided equal length runners in regards to flow. Single 4 barrel intake manifold as shown. Looking closely at the photos, this one has had a repair performed in the past. Intake shipped bare, less carburetor studs, heater tube, vacuum fittings, and water neck where applicable. Ford casting number C6AE-9424-J.

Rechromed GT air cleaner lid for the Mercury Cougar and Ford Mustang equipped with either the Boss 302, GT 390, or 428 CJ engine without the shaker option. It was possible to order a 390 GT motor for your Cougar without ordering the 390 GT package. Cougars equipped with the S code 390 6.5 Litre engine, that did not come with the GT package, would have used the painted air cleaner lid. Replaces Ford part # C7OZ-9661-A.*NOTE* The outside dimension of the lid is 16.75 inches and will not fit the...

This is a 1969 lid. The 1968 lid had several differences, most notable was the stamping wrinkles. This is  Flapper mid plate for use on non-shaker cars. 1969-70 Mercury Cougar with R or Q code engine with ram air. 1969 Mercury mid sized cars such as Montego, and Cyclone all with R code 428CJ or SCJ engines. Ford part number C9ZA-9600-C. This version is said to have been used starting in May of 1968, so there would have been some cars equipped with this mid plate.There are many...

Used engine or 'motor' mount for any 1969 Mercury Cougar or 1967-69 Ford Mustang convertible. There is not a replacement engine mount for the 1967 cars with 289 engine. These have the Ford casting number of C7ZA-6038-F, in the rubber. The mounts that we have in stock are a 30 year accumulation, needless to say it is very limited supply. They all appear to be in good shape without cracks in the rubber. We offer them for those enthusiasts that want correctness for concours judging, we suggest...

Bracket used to mount the thermactor air pump. Casting number C9ZE-9B450-A or C9ZE-9B450-B. Ford part number C9ZZ-9B450-B

Application is for the FE engines 390, 427 428. This assembly is needed for the installation of the cylinder head air supply tubes. Sold as one nut / one ferrule. 8 total needed for smog tube attaching. Originally these were installed in conjunction with a lower tube.

New rubber "O" ring for Ford V-8 distributors from 289/302/351W/351C/429 engines.

Used 1970-72 black AUTOLITE marked oil fill cap with black plastic elbow. Several variations noted from our collection, AUTOLITE and MOTORCRAFT versions. Will need detailing or fresh black paint applied. Would also suggest replacing the rubber grommet. These 50 year old rubber grommets are rock hard and likely leak air. Gasket to valve cover will also need replacement. Even though this cap has a 1971 parts number, we see these on the 1970 351C engines quite often. Replaces Ford part...

Precision machined to the factory specifications. Light gold anodize finish just like the original.

Factory oil cooler as used on 1969-70 R and Q code Super Cobra Jet 428 engines. Nice used condition, comes as shown with one fitting. Will also work for installing an external oil cooler on the other FE motor applications.Ford part number C9OE-6884-B. 

Nicely chromed dipstick tube and dipstick for the Mercury Cougar or Ford Mustang equipped with the 351 Windsor. Replaces Ford part # C9OZ-6750-A or D0AZ-6750-C.

Chromed engine oil dipstick as found on all 1969 Mercury Cougar Eliminator and Ford Mustang with Boss 302 engines (G Code). The handles were chromed originally. Ford part # C9ZZ-6750-A, Ford casting # C9ZE-6750-A.

Concours correct dipsticks for 1967 - 1969 big block engines. These are exact reproductions of the originals with the proper length and oil level for these big block FE's. They have all of the correct markings including the Ford part number and recommended oil weight. Each dipstick is finished with a show quality chrome handle capped with the correct plastic plug. Ford part # C7OZ-6750-A, Ford casting # C7OE-6750-A.

Reproduction blue dipstick tube for the Mercury Cougar or Ford Mustang equipped with the 351 Windsor.

This oil filter is absolutely concours correct. A must for Show. All are silk-screened with multiple colors.

The oil filter made by the original Ford supplier.

New Old Stock oil filter adapter from any 1968-70 Ford with 390 or 428CJ (non SCJ). Fits Cougar, Mustang, Torino, Fairlane, Cyclone, Ranchero, etc. Nice cast aluminum bracket for installing the spin on oil filter and oil pressure sending unit. Ford casting number C8AE-6881-A. Will fit 1967 FE engine blocks too. Those technically used an adapter with a casting number of C0AE-6881-A.

Famous 'Cal Custom' aluminum finned oil pan that was so popular throughout the 60's, 70's and 80's. It has not been available for years, but it is back again. Pan is made from all new pressure die cast tooling and then fully machined to offer a precise fit and leak free installation. These look great in combination with the Finned Air Cleaner and Valve Covers. Replaces Ford Part #: C5ZZ-6675.

Includes drain plug.

Used oil screen pick up tube assembly from a FE or big  block 1966-70 Ford car, such as 352, 390, 410, 428, or 428CJ engine. This is for most front sump oil pans. Used item, should be degreased and cleaned inside and out prior to installation. Tube assemblies with damaged screens, damaged tubes or bends are thrown away or scrapped. We only save undamaged, used oil pick up tubes. Melling sells a quality reproduction of this item. Replaces Ford Part #: C6OZ-6622-A ...

New pair of white and yellow paint sticks for the Mercury or Ford. These units were used by FORD at the assembly plants to mark fender aprons

Front steel vacuum fitting for 390, 427, 428CJ engines. New Old Stock. Replaces Ford part number C7AZ-9A474-A.

New old stock brass intake manifold fitting that screws into the rear of the 428 CJ intake manifold on all 1969 428 Cobra Jet engines. Similar to the 1967-68 version, but this one has an additional smaller nipple coming out of it.  Ford part number C8OZ-9A474-A.

Used threaded PCV valve for use on 390-4V, 428CJ, 427-4V cars from 1967-70. Unknown functioning condition, these have the correct threaded tops and work with either of the 90° elbows available, reproduction or OEM Ford.

Pertronix brand 7mm spark plug wires. These are performance oriented wires compared to the concours spark plug wires. For any 1967-73 Mercury Cougar and Ford with 289 or 302 engines. Black wires and boots, quality spark plug wires taylor made for the small block Ford engines. Recommended by Pertronix for use with the Flame Thrower coils.

Good used single sheave pulley for the alternator on the Boss 302. Ford Part #: C5AF-10A352-H.

C9AF-10A352-A or -B Alternator pulley for use with only one drive belt. Just under 2-3/4" inches in diameter. This later version would have a casting number of C9AF-10A352-A or possibly C9AF-10A352-B stamped on it. Ford master part number is C5AZ-10344-K like the above pulley.

Application, 1969 - 1970 390IP / 428CJ & 428SCJ engines without air conditioning. Casting number 80B. 5-1/2" diameter and 7/16" sheave width.

Application, 1969 Boss 302 Eliminators and Ford Mustang. Ford Part #:  C9OZ-3A733-C Casting #: 90B. 6-3/8" diameter and 5/16" sheave width.

C9OE-9C480-A 1969 and 1970 428 Cobra Jet (R and Q code engines) smog pump pulley with air conditioning, manual and automatic transmissions. 3 bolt smog pump pulley with a diameter of 5.10" inches. Ford part number C9OZ-9B447-A.

1969 Boss 302 Eliminator (G code engine). 3 Bolt smog pump pulley with a diameter of 5.68" inches. Ford part number C8AZ-9B447-E.

Water pump pulley 1 sheave, about 6.11 inches. When measured from the front of the water pump hub (or inside of the pulley) to the center line of the belt sheave the measurement is 2 inches. Application include 1967 Cougar with 289. 1969 Cougar and Mustang with 390-4V. Also various Mustangs 1965-67, all with 289.Replaces Ford casting number C5OE-8509-A.

C8OZ-8509-B 1968 289 or 302 with automatic and 1969 351. All without air conditioning but with power steering. Power steering optional if with dual belt alternators. Two sheave pulley, diameter of 6-7/16 inches. Ford casting number C7OE-8509-D. Overall height or depth is 2-7/16 inches.

C8OZ-8509-C 1968 427 / 390-4V without air conditioning and 1968-1970 428CJ without air conditioning. Thermactor on all applications, power steering optional. 3 sheave pulley with two different diameters. The MPC lists it as 6 inches on the dual sheave portion and 5-1/16 inches on the outer but we find the actual outer most measurements to be 6 1/8" wide on the dual pulley and 5 3/16" wide on the single sheave pulley. When laid on a flat surface the height is 2 3/8" tall. Ford casting number...

Used 'CORE" grade radiator, marked C9ZE-D or D1, .. etc. 20 inch used radiator from 1969 Mercury Cougar with Boss 302 or 351W or 1969 Ford Mustang with 302 or 351W or engines. This radiator will have the lower tank for transmission lines. Core grade, likely it has been recored at some point in the last 45 plus years. Limited to stock on hand.Restoring or re-coring OEM radiators is expensive and more for the concours crowd. New or reproduction radiators makes much more economical sense.Ford...

Used FoMoCo radiator marked C8ZE-L1 and dated 8KB, which we believe is 2nd week of October 1968. This is for an early built 1969 Mercury Cougar or Ford Mustang with 390-4V or 428CJ and 4 speed transmissions. Good used radiator for recoring and restoration.Replaces Ford part number C8ZE-8005-L or C8ZZ-8005-C.

Found on standard cooling and non-air conditioned Mercury Cougar and Ford Mustang 1969 - 1970 all engines. One per car, one on the drivers side of the radiator. *Note - This is a shorter side shield than is found on the 1967 and 1968 Cougar.*Note - Block off plate not needed with the 24 inch radiators.

New 13 Pound Generic Radiator Cap with Safety Release for the 1967 - 1973 Mercury Cougar / Ford Mustang

These concours quality Chrome caps are made in America and bear all the original markings. O.E.M. details include original letter style, "S.M.C.O." and "Autolite". Pound rating is stamped on cap. Replaces Ford Part #: C7ZZ-8100-A.

Brass sensor that screws into intake manifold and activates temperature gauge in dash. Replaces Ford Part #: C6DZ-10884-B (SW-552) or C9WY-10884-A (SW-888)*. Temp Sender Switch Temp Rating : 15.2-19 Ohms Resistance At 220 Deg F Temperature Switch Thread Size : 3/8" x 18 NPT * - The 1969 351 Windsor temperature sending unit has been discontinued. Most manufacturers list the 1968 302 temperature sending unit as the closest replacement.Check out the video below on our new gauge tester: ...