Interior

NOS plastic brackets that screw to your roof and then slide a vinyl colored piece over. Sold individually, two are required per car. Ford part # C8AZ-6229232-A.

NOS white colored coat hooks pair. Reproductions only come in black, these are new in the package. White color started in 1970, off white and parchement 1968-69. Fits 1968-73 Mercury Cougar and Ford everything including that Mustang. Ford Part #: D0AZ-6229024-K.

New old stock deluxe shifter handle in light aqua. Perfect condition, no cracks in the plastic. No release button or set screw included. NOS Ford part number C8OZ-7213-AQ The 67 version was actually a little different. Check out our video on rebuilding your shifter below: ...

This is an original chrome lock knob used on 1968 and up Fords with no peeling chrome or obvious scratches. If you compare the originals to the reproductions we have listed you will see a distinct difference. This is for the very particular restorer who really is concerned about detail, especially on prominent pieces like this. Sold individually, very limited supply.Original Ford part number is C8AZ-6221850-A

Good original passenger side door latch rod set. Includes rod for inside lock, outside key lock, and outside door release actuating rod. These are good used parts and are a better quality and value compared to the reproductions. Only fits passenger side doors of 1968 Mercury Cougar and Ford Mustang. 1968 door latches are unique, they have a longer tab for the inside door lock knob typically. Check out our handy diagram below to find other '67-'68 door parts you may need. All the item numbers...

These NOS sill plates always have some degree of shelf wear due to the many years they have been shuffled around. The biggest difference you will see with NOS vs. the two different levels of reproductions is the finish. The NOS parts are far less bright and less prone to showing hairline scratches. One other benefit is that NOS sill plates already have the FORD decal in place. Sold individually.

These interchange left to right, they are a mirror image of one another. We recently did a side by side comparison of these so called "concours" sill plates and found very little difference when comparing them to the "economy" version... They both weigh .52 pounds, just like our NOS sill plates. They both have a high of luster, unlike the originals which featured very little "shine". We found the screw holes to be just a tad larger on the economy version but once the screw is inserted you...

Used rectangular center duct tube for any 1967-68 Mercury Cougar or Ford Mustang with integral or factory air conditioning. Wire reinforced foam, will show some snags or signs of use. Will not have gaping holes. Was originally stapled to the center housing. Ford part number C7ZZ-19B680-B.

These are sold individually, two required per car. This is the aluminum emblem / decal which mounts on the center of all of the 68-73 scuff plates. Features raised script like original. Adhesive backed with a protective coating that peels off after installation. Replaces Ford Part #: C7ZZ-6513208-T.Licensed by FORD

Used end cap with the burl woodgrain for the deluxe door pull straps found in the Mercury Cougar XR7 or Ford Mustang. These units will show a degree of pitting, fine scratches and fading. Also, these door pull strap caps are unique to 1968 and they are not currently being reproduced. 1967 has no border and the woodgrain has a different color and look to it. This is for the person that must have correctness in detail or they just need one to finish off their interior. We highly recommend...

This white plastic spacer fits into the back of the right hand inner knob on cars without factory fader or balance. If your inner knob is loose and will not align, you will want to see if this part is in place. The pictures show an example of how it looks once installed. 1968-70 AM-FM radios would not utilize this part because they have a balance feature. Also found on various 1976-70 Ford and Mercury cars such as Galaxie, Fairlane, Torino, Ranchero, Falcon, Montego, and Thunderbird. The knobs...

Core bench seat for the 1968 Mercury Cougar or Ford Mustang equipped with decor interior. 1968 bench seat without optional headrests, but with seat seat back release latches. The foam will almost always be deteriorating or even missing. All seat cores will be solid frames taken from a Western parts car. Keep in mind 68 and 69 are identical except for how the head rests attach. You can easily add head rests from 69 buckets and bolt them to a 68 pair of buckets or bench if you have all the...

Early 1967 style glove box catch. Fits all 1967-68 Cougars and 1966-68 Mustangs.Replaces Ford part number C6OZ-6206064-A.

Reproduction Glove Box Catch for the 1967 and 1968 Mercury Cougar and Ford Mustang

New old stock 1968 glove box lock. A great optional accessory. All original glove box latches. Includes 2 matching aluminum keys. Fits any 1967-68 Mercury Cougar or Ford Mustang.Ford part number C6OZ-6206081-C. Technically the lock style is for 1968, notice the push button with rounded edges? 1967 push buttons had square edges. 

Correct for any 1967-73 Ford product with a tilt or fixed column. The repros are fine, but the end knob is distinctly different. Extremely difficult part to find in NOS form and very sought after. Keep in mind we also have excellent used pieces at a fraction of the cost. Ford part # D0AZ-13305-A.*NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is the designer of all of...

Note: The set you receive may not be the ones pictured and will usually be in better condition than shown. The chrome bezels will all be in good matching condition, unlike the blemished one in the picture. Call if you need more details or to check inventory on colors. Used pair of dual post head rests for the Mercury Cougar or Ford Mustang. These ultra rare head rests were an option in 1968 only and may come with some slight blemishes. Your 1968 Mustang / Torino / Thunderbird / Cyclone seat...

Currently out of stock. Do you have a pair for sale? Let us know! Four required per car, bolts to the back side of the upper portion of your 1968 seat frame. According to the 1968 Cougar assembly manual the Ford part number is C8ZB-65610B10. This part has an adjustment to fine tune the headrest post alignment.

Good used headrest with no mounting hardware included. No cracks. We never have more than one of these in stock as a single so we most likely will not be able to produce the color of your choice but it never hurts to ask! Basic Ford part number for this item is C8AB-62611-A08. The "08" suffix part of the number may refer to a specific color.

Driver quality used left side or driver side folding door handle. This type of handle was used on the 1967 XR7 models and 1968 Cougars. This is also the deluxe handle found in Mustang and other Ford / Mercury cars. Some pitting, will have a good spring and rubber bumper. Sorry mounting screw not included.

Driver quality used right side or passenger side folding door handle. This type of handle was used on the 1967 XR7 models and 1968 Cougars. This is also the deluxe handle found in Mustang and other Ford / Mercury cars. Some pitting, will have a good spring and rubber bumper. Sorry mounting screw not included.

Sold as a pair, these are a perfect fit, correct texture and are less prone to cracking than originals. They do not have the perforated speaker holes for those utilizing kick panel speakers. Check out our custom made kick panels that accommodate modern speakers.

Reproduction interior kick panels in parchment / off-white for the Mercury Cougar or Ford Mustang. Sold as a pair, these are a perfect fit, correct texture and are less prone to cracking than originals. They do not have the perforated speaker holes for those utilizing kick panel speakers. Check out our custom made kick panels that accommodate modern speakers.

Sold as a pair, these are a perfect fit, correct texture and are less prone to cracking than originals. They do not have the perforated speaker holes for those utilizing kick panel speakers. Check out our custom made kick panels that accommodate modern speakers.

Rubber isolator used in tilt away steering column near the lower bearing. Two required per car. There is an active thread on the Classic Cougar Community Forum discussing tilt columns and trouble shooting. *NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year. ...

This mounts at the top front corner of the driver side rear interior panel. Ford called this part a "Cap - quarter trim panel upper". All 1967-68 Mercury Cougar and also used on 1968 Ford Mustang coupe with deluxe interior or body code 65B.You may also need the attaching screw. Replaces Ford part number C7WY-6531491-B or C7WB-6531491. Fits 67 CougarFits 68 CougarFits 68 Mustang with body code 65B ...

This mounts at the top front corner of the passenger side rear interior panel. Ford called this part a "Cap - quarter trim panel upper". All 1967-68 Mercury Cougar and also used on 1968 Ford Mustang coupe with deluxe interior or body code 65B.You may also need the attaching screw. Replaces Ford part number C7WY-6531490-B or C7WB-6531490. Fits 67 CougarFits 68 CougarFits 68 Mustang with body code 65B ...

Factory knob for the new for 1968 rear window defogger. This is the knob for the 2 speed fan switch mounted to the bottom dash on cars so equipped. Rare option, we try and match these up to the switches. Spares occasionally come in, subject to availability.

Good reproduction of a knob that is always broken off. Made from milled aluminum rather than plastic as the originals were made. This makes it so it is not as susceptible to breaking off. Unique to Cougars with tilt columns in 1968 - 1969. Replaces Ford part number C8MY-17513-C. This part also fits the 68-69 Mustang, Lincoln, Marquis, Thunderbird and other like models with an adjustable steering column.

Used emergency flasher knob for the tilt / tilt away steering column equipped Mercury Cougar or Ford Mustang. This unit is a very fragile part which we never find in good used condition. What you will see when it has been broken off is an exposed Phillips screw head. *NOTE* WCCC services all FoMoCo tilt and tilt-tilt away steering columns 1967-1979. Our shop rate for this service is $90 per hour and most columns with serious problems do need complete tear down and build up which usually takes...

Hard to find knob with no crack or peeling issues, correct for right or left side Torino, Cougar, Mustang. Not for use with console equipped Mustang and Cougar. Casting number is C8OA-18A932-B.

Used on the Mercury Cougar or Ford Mustang with a factory center console and measures 1-3/8 inches tall. Replaces part # C8ZA-8A932-B

This is correct for your 1968 non console Mustang or Cougar. Fits left or right, no cracks or peeling. Casting number is C8ZA-18817-E.

Reproduction radio knob used on Mercury Cougar or Ford Mustang with a factory center console. Replaces part # C8ZA-18817Fits: 1968 Mercury Cougar

Used on Mercury Cougar or Ford Mustang with a factory center console. Replaces part # C8ZA-18817Fits:1968 Mercury Cougar

This set of knobs is for 1968 Cougar / Mustangs without factory console. The exception to the rule would be the XR7G. Cougars equipped with a console need the longer version of this knob to clear the padded console face. If you happen to have a 1969 or newer radio then the radio has longer shafts and these knobs may in fact work with a console. The radios that would not utilize the white plastic spacer would be 1967 radios with factory rear speakers, 68-70 AM radios with rear speakers and...

Good used set of four knobs for your Mercury Cougar or Ford Mustang with a factory center console. These are plastic and much deeper than the non-console version. The radios that would not utilize the white plastic spacer would be 1967 radios with factory rear speakers, 1968-70 AM radios with rear speakers and 1968-70 AM-FM radios, if you need the white spacer we offer it here. Our blow-out price is based on the fact that these are now available new! Knob length 1 1/2"Sleeve length 1 5/16" ...

1967 Cougar Owners: To view our exploded view interactive diagram of the tilt steering column parts, click here. Used upper knuckle for the tilt / tilt away steering column equipped Mercury Cougar or Ford Mustang.  There is an active thread on the Classic Cougar Community Forum discussing tilt columns and trouble shooting. *NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way...

This used assembly includes lamp socket, bracket, mercury switch, and length of wire.Replaces part # C7ZB-15702-A

Used only in 1968 Manual 3spd and 4spd on non xr7 models and Mustang. Very hard to come by with no splits, burns or cracks. We rarely can supply the color you desire but please let us know your desired color and we will try. Grade A will not have UV ray damage and will look right at home in a low mile car. Satisfaction guaranteed.

These reproduction A pillarpads / moulding / trim were used on the 1967 - 1968 Mustang Coupe and Fastback and even though they carry a C7WB part number on the back side they were never used on a 67 or 68 Cougar. Reason being is they are two wide to fit next to the wide Cougar roof side Pinch weld moulding, soft trim. If you use the thin inexpensive pinch weld moulding we sell you can use these. Also note that the 1968 1/2 standard level interior used the thin pinch weld moulding from the...

These reproduction A pillarpads / moulding / trim were used on the 1967 - 1968 Mustang Coupe and Fastback and even though they carry a C7WB part number on the back side they were never used on a 67 or 68 Cougar. Reason being is they are two wide to fit next to the wide Cougar roof side Pinch weld moulding, soft trim. If you use the thin inexpensive pinch weld moulding we sell you can use these. Also note that the 1968 1/2 standard level interior used the thin pinch weld moulding from the...

Reproduction pillar post mouldings for the Mercury Cougar or Ford Mustang. These units are sold as a pair.

Reproduction pillar post mouldings for the Mercury Cougar or Ford Mustang that feature two 2" gauge pods on the driver side. Sold as a pair.

Good reproduction but our used unit is a better value and will clean up just as nice.

CRL brand glass bedding compound for installing the 1967-68 glass windshields and 1967-73 back glass that use rubber gaskets. This is a non-hardening material that seals the glass to the rubber

Used pivot pin for the Mercury Cougar or Ford Mustang / Thunderbird equipped with a tilt / tilt away column. This is a pressed pin with a flange and five are required per car. This pin is internally threaded with a # 6-32 thread. Ford part # C7SZ-3D739-A. *NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year. ...

Factory radio delete or block-off plate from a 1967-68 Mercury Cougar or Ford Mustang. Seldom seen part, roughly 5% of all 1967-68 Mercury Cougars were ordered without any type of radio from the factory. Similar story with the Ford Mustang, most owners added some sort of radio or stereo soon after delivery. The factory radio bezels were made from chromed pot metal, these radio delete plates are made from plastic and vacuum chrome plated. This used example pictured, has most of the plating...