All Available Parts - 1967 Mercury Cougar

This ultra rare NOS center cap decal features a black background and a chrome walking cat and was used when the 10 spoke 15" aluminum Shelby wheels were ordered for your Mercury Cougar. The wheels were marketed through Shelby American in the Cougar catalog titled, "How To Sharpen Your Cats Claws". I was able to obtain the last of their inventory through a previous employee when they closed the doors in the mid 70's. They measure 1-13/16" in diameter and fit well into the 3 bar spinners used on...

NOS Back up light switch for the 1967 Cougar or Mustang. Ford Part # : C7ZZ-15520-A

D5DZ-6221813-A Not for XR7.

C60Z-3047-A Used on many Ford products starting with the 1966 Ford Fairlane.

C7AZ-6571-B

C5ZZ-6522600-C

Original or NOS Ford distributor cap.

C5ZZ-13217-B Front parking lamp to body gasket, driver side. 1967-68 Mercury Cougar and 1965-68 Ford Mustang.

This listing is for a 3 bolt type upper ball joint, NOS, original Ford Service replacement upper control arm assembly. We have a very hard time keeping these in stock but we keep the listing up as it is good for comparison sake when considering the differences between reproduction and OEM. Keep in mind, service replacement parts often differ slightly from what actually came on the car. Over the years tooling is often replaced or modified and suppliers of things like fasteners often change....

Nothing matches the fit and feel of NOS. This will outlast the reproduction armrest three to one.

They made three different versions of this plate for non console Mercury Cougars equipped with a manual three or four speed transmission. This part was not found on Mustangs as the Cougar often used a little "fancier" detail items in and out. Check out our video on rebuilding your shifter below: ...

Sold as a pair only, very limited supply. Driver side part number is C7WY-16304-B and passenger side part number is C7WY-16304-A. The casting number imprinted on the part is C7WB-17B957-B for the driver side and C7WB-17B951-B on the passenger side. The Mercury MPC refers to these as "anti squeak pads".

Also referred to as "Bumperettes", this kit was available as an over the counter option for your 1967 or 1968 Mercury Cougar. According to Kevin Marti's book, "Cougar By The Numbers" 15,018 Cougars received rear bumper guards from the factory in 1968, that data is not listed for 1967 but it is assumed that the numbers are about the same. Keep in mind that the installation of this kit requires drilling two holes in your rear valance, for an example please check out our used valances in the...

Rare find in NOS form. Sold as a pair only. Driver side carries a C7WY-16304-C Ford part number and the passenger side carries a C7WY-16304-D part number. The casting number on the driver side is C7WB-178951-A and the passenger side has a C7WB-17B957-A casting (or engineering) number imprinted on the top of the part.

NOS grille headlight eyelid door vacuum actuator for the Mercury Cougar. No exchange needed for NOS. *NOTE* While original FoMoCo boxes are fun and all, we do not recommend you invest in these units as shown with the multiple crimps at the top. These later dated service replacement units shown here were made out of country and are inferior to what the OEM supplier made back in "the day". The rubber elasticity is not as good as the early units and the porosity of the metal makes them impossible...

Rare find in NOS form and rarely are we able to keep these in stock. The driver side carries a C7WY-6529031-A Ford part number and the passenger side carries a C7WY-6529030-A part number. The Ford engineering number imprinted on the part is C7WB-65280A95-A on the driver side and C7WB-65280A94-A. They are also marked with an R and L to denote which side the attach to.Sold as a pair only.

Very rare find... A restored bezel will look fine but will never retain the sharp edges and matte black finish like this new in the box original Ford part.

C5ZA-2454-G or C5ZZ-2454-D New Old Stock manual transmission disc brake pedal pad with stainless steel insert as shown. Application is 1967-70 Mercury Cougar and 1965-70 Ford Mustang, 3 or 4 speed manual transmissions.

C6OZ-7A533-C. Clutch Pedal Rod To Firewall Seal. Much better than repro. Also fits 1966 Mustang / Fairlane / Comet and others.

D5DZ-6221812-A

NOS Ford key blank for ignition and doors.C7AZ-622053-A Sold Individually. This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of 50% of our web price for parts delivered in hand or by carrier to our Brooks, Oregon location. If you're not interested in store credit, just shoot us an email and we will let you know if it's is something we can pay cash for. We do not send cash for parts in...

Replaces Ford Part #: C6OZ-3C651-A or (service replacement for) C1AZ-3C651-A

These NOS sill plates always have some degree of shelf wear due to the many years they have been shuffled around. The biggest difference you will see with NOS vs. the two different levels of reproductions is the finish. The NOS parts are far less bright and less prone to showing hairline scratches. One other benefit is that NOS sill plates already have the FORD decal in place. Sold individually.

[No Description Provided]

C4DZ-5415-A Sold as a pair

This rare accessory was only offered over the counter, it was not available as a factory option. Great upgrade for the 1970-1973 Cougar owner as cruise control was discontinued after 1969 and not offered again until 1974 on the Mercury Cougar.Ford part number C8OZ-9B742-AClick on images to enlarge. ...

Very rare find in the original service replacement boxes dated 10-07-75. Sold as a pair.Ford part # C8WY-65502B20-A.Click on images to enlarge. ...

Hard to tell the difference between this and the reproduction version except for one *HUGE* difference!!! The reproduction was made to adhere to the outside of the drivers side quarter window and the originals adhere to the inside! Incredibly rare and cool find from a local dealer, very limited supply as you can imagine. Made by Fasson which was the company that made most of the decals for Ford in the 1960's and 1970's. Check out the very first Cougar in our video below! ...

This is an original NOS hot idle compensator for Mercury Cougar or Ford Mustang models with V-8 engine and factory A/C. It is installed in the middle of the hose that connects the PCV valve to the rear of the carburetor spacer. It opens when it reaches a certain temperature which makes the engine run faster when at idle and the A/C is on thereby making the engine run more efficiently. This is an original Ford part that came on air conditioned models from the factory. It was manufactured by...

Rare find, must have for your Concours Cougar. Sold individually.Ford part number C5ZZ-1012-BFits the following models with Styled steel wheels:1967 Mercury Cougar1968 Mercury Cougar1969 Mercury Cougar1970 Mercury Cougar1967 Ford Mustang1968 Ford Mustang1969 Ford Mustang1970 Ford Mustang

Generic hose kit that will fit the 289 or 302 for those who are not concerned about the CONCOURS look. Used on both the 20" and 24" wide radiators Replaces Ford Part #'s C4ZE-8260-A and C4ZE-8286-A. For some helpful tips on upgrading your Cougar (or Mustang) cooling system, check out our video: ...

NOS power steering ram cylinder dated 6H25 or August 25, 1966. This one is date coded for a very early built 1967 Mercury Cougar or Ford Mustang, including Shelby GT350 and GT500. Bendix manufactured, shows a paint marking and gold cadmium? nut and band. Still has the plastic plugs and cardboard protection on the threaded shaft and drag link stud. Seals presumed to be good, but no guarantees.

Please use our contact form to inquire about current colors and conditions of stock on hand. This listing is an example of what you can expect from a grade "A" pair of 1968 decor door panels from us. These are given the grade "A" rating because there is minimal discoloration and light general wear. These panels are very hard to find in grade "A" condition. Most of our panels range in price from $250-$600. NOTE: The pictures shown here are file photos from sets we have sold in the past and...

This reproduction cigar / cigarette lighter socket is a good fit and is easy to install. This lighter socket also comes with the retainer. Replaces Ford part # C6ZZ-15055-B.

Used grade "A" pair of XR7 door panels for the Mercury Cougar. Keep in mind you would not want to paint these panels if at all possible as they have streaks of black in them that cannot easily be duplicated. Black panels would be the exception. Also keep in mind these listings are just a sample of what we often have on hand. We are not able to list all of our used panels and ask that you email or call for stock on hand. Most of our panels range in price from $250-$600. Often at least one map...

Reproduction fuel line that goes from the fuel pump to the carburetor made of OE steel for the Mercury Cougar or Ford Mustang equipped with the 390-4V engine. Fits all FE engines with Holley 4150, as long as they do not have the Carter "X" fuel pump. Carter X fuel pumps are not crimped together.

Used XR7 grade "A" main under hood wiring harness located in the engine compartment. This harness has plugs for the head lights, voltage regulator, starter solenoid, windshield washer pump, and horns. All electrical harnesses are inspected, tested, and ready to install. Grade "A" harnesses are rare uncut beauties. 1967 Mercury Cougar XR7 models only. Not compatible with Standard model Cougar with AMPS warning light. Ford part # C7WY-14290-H.

Differs from all other Cougar console wiring in that it has a black plug for the shift indicator light.

Used XR7 grade "B" main under hood wiring harness located in the engine compartment. This harness has plugs for the head lights, voltage regulator, starter solenoid, windshield washer pump, and horns. All electrical harnesses are inspected, professionally repaired, tested, and ready to install. Grade "B" harness may have one or two repairs where the grade "A" harnesses will be rare uncut beauties. 1967 Mercury Cougar XR7 models only. Not compatible with Standard model Cougar with AMPS warning...

Reproduction console feed harness for the 67 - 68 Cougar or Mustang. This OEM direct fit wiring harness supplies power from the under dash harness to the console harness.

New Old Stock center cap emblem for the Mercury Cougar with XR7 hubcaps / wheel covers. On the XR7 package, this concave aluminum applique was applied to the center of the hubcap / wheel cover. Called an applique. Used only in 1968 on the one style XR7 hubcap. Not sure why it has a 1969 part number, error? Ford part number C9WY-1137-A.

Used set of four nuts and two locking washers used on the knob shafts of all radios 1967 - 1973 used on Cougars, Mustangs, Galaxie, Torino etc.

Used radio bezel Grade A used. For use on 1967-68 Mercury Cougar or Ford Mustang cars without console. 2-3 different castings, need to be side by side to see minor difference. Ford part # C8ZA-18842 and C7ZA-18842.

Factory radio delete or block-off plate from a 1967-68 Mercury Cougar or Ford Mustang. Seldom seen part, roughly 5% of all 1967-68 Mercury Cougars were ordered without any type of radio from the factory. Similar story with the Ford Mustang, most owners added some sort of radio or stereo soon after delivery. The factory radio bezels were made from chromed pot metal, these radio delete plates are made from plastic and vacuum chrome plated. This used example pictured, has most of the plating...

Used functional Mercury Cougar AM-8 track Motorola manufactured radio. These will work and all wiring plugs will be present. Good working and tested radio, fresh installed 8 track belt, may have minor cosmetic issues from a past life. Ford master part # C7WA-18806-A, Chassis and Escutcheon Assembly. *NOTE* Does not include brackets or knobs. Are you going to install this unit yourself? The first issue of Legendary Cougar Magazine has a great how to article that will help you in your journey to...

T7SMW 1967 Mercury Cougar AM-8 track Motorola manufactured radio. May or may not work and wiring plugs may be cut. Good radio for reconditioning, often times the face plate is missing or damaged, one or more functions won't play, etc. Ford master part # C7WA-18806-A, Chassis and Escutcheon Assembly. Are you going to install this unit yourself? The first issue of Legendary Cougar Magazine has a great how to article that will help you in your journey to musical bliss. You can get it here! ...

Used chrome / red center cap for the 1967 and 1968 Mercury Cougar and Ford Mustang Equipped with the Wire Spoke Hubcaps / Wheel Covers. Fits:1967 Mercury Cougar1968 Mercury Cougar

Used grade "A" simulated wire spoke hubcap with 3 bar spinner center / wheel cover that is in excellent condition with no curb scrapes, stress cracks in plastic center or pits in die-cast. The spinner was discontinued in 1967 so only the early models would have them in 67.Ford part # C7WY-1130-B

Used grade "A" simulated wire spoke hubcap / wheel cover that is in excellent condition with no curb scrapes. This listing is for someone who has removed their center from their current damaged cap and wants to save money by purchasing a cap with no center. The same cap was used on Most all FoMoCo products including but not limited to the Falcon, Mustang, Fairlane, Comet, Galaxie, Montego and LTD, only the center logo changed one car to the next. Ford part # C7WY-1130-C. *NOTE* You will often...

Used grade "A" simulated wire spoke hubcap / wheel cover that is in excellent condition with no curb scrapes, stress cracks in plastic center or pits in die-cast. Ford part # C7WY-1130-C.*NOTE* You will often see this same cap with the Mercury head center and a red background. This cap is not correct for Cougar, but was found on other Mercury products such as the Montego.

Used / refurbished center cap emblem for the Mercury Cougar with XR7 hubcaps / wheel covers. On the XR7 package, this concave aluminum applique was applied to the center of the hubcap / wheel cover. These are always faded, so we've "restored" a few with Sharpies, as shown in the picture. Believe it or not, it works pretty well and allows the shiny aluminum to show through the red. Be advised that the sharpie treatment doesn't hold up very well to rain and weather, so this is best for garaged...

Used chrome / black center cap for the 67 - 68 Mercury Cougar equipped with the wire spoke hubcaps / wheel covers.Fits:1967 Mercury Cougar1968 Mercury Cougar

Used chrome / black center cap for the 67 Mercury Cougar equipped with the wire spoke hubcaps / wheel covers. The spinner was only available on cars made prior to 1967 as they were outlawed.Used in conjunction with Mercury cap part # C7WY-1130-C Check out the very first Cougar in our video below! ...

Due to time constraints, we can no longer offer the service of having your own mirror restored, this is now an exchange based service only.Any mention of it in the video below is outdated, please disregard. Restored 1967 early style larger rectangular rear view mirror lens for the Mercury Cougar or Ford Mustang. Unlike our full price restored lenses, these require no core. These lenses look good at first, but if you look close you may see a scratch, tiny chip around the perimeter or...

Pressure die cast, with quality chrome sun visor center bracket and rear view mirror mount. Replaces one of the most visible interior parts on a 1967 Mustang or Cougar. Break away style, two piece construction. Beware of cheap single piece imitations that are available as they are unsafe. Keep in mind you will have to give your screw driver some good pressure when installing to make the mirror fit tight. Replaces Ford part # C7ZZ-17690-A.These are manufactured in the USA. ...

NOS or new old stock - C7SZ-13A165-A Bolt like pin that one or both sides of the hidden headlight hinge rides on. 1967-68 Mercury Cougar uses 4, 1969-70 Mercury Cougar uses 2 on the outsides. Also used on many other 1967-71 Ford, Mercury, and Lincoln cars with the vacuum operated hidden headlights. 1967 - 1970 Mercury Cougar and XR7 1967 - 1969 Ford Thunderbird or T-Bird 1968 - 1969 Ford and Mercury full sized cars 1971 Ford and Mercury full sized cars 1970 and newer Lincoln Continental...

NOTE: WE SUGGEST LOCAL PICK UP ONLY FOR CORE ENGINE BLOCKS BECAUSE WE CANNOT GUARANTEE BLOCKS WILL NOT HAVE CRACKS INTERNALLY. Long block, factory A code 289-4V V-8 engine. Rated at 225 Hp with 9.8:1 compression ratio in 1967. Not standard bore engine block, that may or may not have been in running condition when pulled. May or may not have 9.8:1 pistons. Guaranteed to be rebuildable. Complete engine less carburetor, distributor, exhaust manifolds, fan, accessories, pulleys, and flex...

This option requires you to PRE-PAY a $40 core charge. If we do not receive your core within 30 days of the original purchase, your core charge will be an in-store credit only. If your core is full of rust and debris (sounds like a tambourine) then it most likely is not a core we can give credit on. ALL GRADE B ACTUATORS COME WITH A 60 DAY WARRANTY. You can find the seal rebuild kit here. Used grade "B" headlight door actuator for your Mercury Cougar. Every once in a while (not often) we will...

This used original, color coded set of vacuum hoses is 100% complete and relatively pliable. It comes complete with decades of dirt and grime (patina) for no extra charge. If you want to remove the grime it will take some serious elbow grease but it can be done. The color coded stripes are quite resilient to cleaning as the ink used actually embedded itself into the rubber. "I found a good way to remove 50 years of crud. Soak the lines in hot water and dawn dish soap for a bit then take a...

This single port version was used in the latter part of 1967 and all of 1968. Keep in mind we have units that are not as clean looking but still hold vacuum for about half the price. Cougar part number C7WY-13A185-C headlamp vacuum reservoir.

This used original, color coded set of vacuum hoses is 100% complete and relatively pliable. It comes complete with decades of dirt and grime (patina) for no extra charge. If you want to remove the grime it will take some serious elbow grease but it can be done. The color coded stripes are quite resilient to cleaning as the ink used actually embedded itself into the rubber. If you have a tried and true method of cleaning these hoses let us know and if it sounds good we will post it here!NOTE:...

All of our used insulation hood pads are guaranteed to be filthy dirty, less than perfect (as shown) and include at least one spider. We cannot fold these to ship them and they are too large for UPS. You must pick them up in person or we can ship them for free when you purchase a hood from us.

NOTE: WE SUGGEST LOCAL PICK UP ONLY FOR CORE ENGINE BLOCKS BECAUSE WE CANNOT GUARANTEE BLOCKS WILL NOT HAVE CRACKS INTERNALLY. Dated 5L18, November 18, 1965.  Used 0.030 over bore 4.180" Ford 428 engine block. Bare block, no crank shaft. Will be used, dirty. Good for rebuild or assembly, quality of machining unknown. Bare block, may have C6ME, castings. When we have them in stock we will post the casting date or dates. Heavy, will require either local pickup or freight...

This is what is referred to as a campaign part. It was found that the early 1967 Cougars were having some issues with the headlights and this revised hose kit with ground strap was the fix. Often these have been found opened on dealers shelves with the "near new" take off hoses placed back in the original box. This is a great find for the guy wanting to do a concours restoration on his 1967 Mercury Cougar. Not for use on a 1968 as the switch was located under the dash as opposed to next to the...

NOTE: WE SUGGEST LOCAL PICK UP ONLY FOR CORE ENGINE BLOCKS BECAUSE WE CANNOT GUARANTEE BLOCKS WILL NOT HAVE CRACKS INTERNALLY.Used standard bore 4.00" Ford 289 engine block. Will be used, dirty, have measurable taper, and will have a ridge. Good for rebuild. Bare block, may have C6AE, C8AE, castings. When we have them in stock we will post the casting date or dates. Heavy, will require either local pickup or freight shipping.  Dated 6K4 or October 4, 1966.  This item cannot ship...

NOTE: WE SUGGEST LOCAL PICK UP ONLY FOR CORE ENGINE BLOCKS BECAUSE WE CANNOT GUARANTEE BLOCKS WILL NOT HAVE CRACKS INTERNALLY. Dated 7L1, November 1, 1967.  Used standard bore 4.05" Ford 390 engine block. Will be used, dirty, have measurable taper, and will have a ridge. Good for rebuild. Bare block, may have C6ME, C7ME, castings. When we have them in stock we will post the casting date or dates. Heavy, will require either local pickup or freight shipping.  This item cannot ship...

NOTE: WE SUGGEST LOCAL PICK UP ONLY FOR CORE ENGINE BLOCKS BECAUSE WE CANNOT GUARANTEE BLOCKS WILL NOT HAVE CRACKS INTERNALLY. Dated 8B21, February 21, 1968.  Used standard bore 4.05" Ford 390 engine block. Will be used, dirty, have measurable taper, and will have a ridge. Good for rebuild. Bare block, may have C6ME, C7ME, castings. When we have them in stock we will post the casting date or dates. Heavy, will require either local pickup or freight shipping.  This item cannot ship...

Hard to find pair. This letter series would have been issued in 1968-1969. This particular pair could use a bit of restoring to get back to perfect condition, but they are in good shape and will not have any extra holes like the grade B plates do.   NOTE:  "Due to programming limitations, a license plate that still has a record on the database cannot be reassigned. Therefore, customers returning to California after registering their vehicle out of state cannot have their old...

Used Bracket for mounting the Servo on any 1967-68 Mercury Cougar or Ford Mustang with speed control. The Servo is the rubber bellows. Ford part number C7ZZ-9C736-A.

Big bell shaped oil pressure sending unit for 1967-73 Mercury XR7 and 1967-73 Ford Mustang with actual oil pressure gauges instead of idiot light for the oil pressure. *Note - this pressure switch does use the press on wiring boot. Please check your wiring harness for the proper connector. This oil pressure sending unit also fits the following cars that have analog oil pressure gauges: 1969-71 Continental MKIII, Thunderbird 1965-71.Replaced Ford part # C9ZZ-9278-A Check out the video...

Our grade "A" 1967 - 1968 fender extensions have no obvious dings, scrapes or warping due to over tightening of studs. Hardware not included but if you ask for it we will try to include it at no charge. Note that the inner part just behind the eyebrow moulding is painted black from the factory.Ford casting number as seen from the back side reads C7WB-16019-A. Do you have questions about your Cat’s factory pinstriping? This link may help. This icon means that we're looking to buy this...

Hard to find pair. This letter series would have been issued in 1968-1969. This particular pair has extra holes drilled, which would need to be repaired (see pictures). They could be restored or used as-is. Because of this, we're selling them at a reduced price. NOTE: "Due to programming limitations, a license plate that still has a record on the database cannot be reassigned. Therefore, customers returning to California after registering their vehicle out of state cannot have their old...

New intake manifold that has never been used, but it's missing the packaging, so we're calling it an "out of box special". Port size is for the 2V cylinder heads. Perfect for adding a 4 barrel carburetor to a stock 351 Cleveland 2V engine.

It is not often we get perfect used but nothing fits like OEM!The Engineering number on the bottom of the passenger side reads C7ZB-6521448-ACheck out our video below for helpful tips on disassembling your vent and quarter windows: 67-68 Cougar/Mustang Vent & Quarter Windows - Disassembly for Restoration

Original NOS part, new in box. Ford part # C5ZZ-6503110-A

Reproduction gas tank to filler pipe hose fits the 67 to 70 Mercury Cougar, measures 4 1/2" long. Excludes 1970 with California emissions. Even if yours is not cracked it will be hard if it is over two decades old. We highly suggest you replace this part if yours is in fact hardened with age because a minor rear end collision could cause it to fail and send fuel spilling into your trunk area. Replaces Ford part #: C8ZA-9047-A.

NOS lower inside door seal for any 1967-68 Mercury Cougar or Ford Mustang. No wrapper, this is not a reproduced item. Not very many Cougars or Mustangs came with this seal, we think it may have been for wind noise? Unknown. These are pre-drilled for mounting, no hardware included.Replaces Ford part number C7WY-6520272-A.

Excellent reproduction seals for your 67 - 68 Cougar or Mustang vent windows. Made from Ford's Original Tooling. Much better fit than other reproductions. Replaces For part numbers:C7ZZ-6521449-AC7ZZ-6521448-A

New rubber body plug, fits oval rear shock access hole. 1-3/4" x 3-5/16" oval holes. Sold individually, Usually 2 per car. Fits 1967-70 Mercury Cougar and Ford Mustang.Replaces Ford plugs marked 378923-S.

CRL brand glass bedding compound for installing the 1967-68 glass windshields and 1967-73 back glass that use rubber gaskets. This is a non-hardening material that seals the glass to the rubber

Reproduction disc brake pedal pad for the 1967 Mercury Cougar or 1965-67 Ford Mustang equipped with the automatic transmission. This is identical to the 1968-73 pad, just slightly narrower. 1968 was the introduction of many Federally mandated safety upgrades, the larger pedal being one of them. Replaces Ford part # C5ZZ-2454-C.

Made from Ford's Original Tooling. Much better fit than other reproductions. Replaces Ford Part # : C7ZZ-6521449-O Check out our video below for helpful tips on disassembling your vent and quarter windows: 67-68 Cougar/Mustang Vent & Quarter Windows - Disassembly for Restoration

Made from Ford's Original Tooling. Much better fit than other reproductions. Replaces Ford Part # : C7ZZ-6521448-O Check out our video below for helpful tips on disassembling your vent and quarter windows: 67-68 Cougar/Mustang Vent & Quarter Windows - Disassembly for Restoration

These are a higher quality rubber than the other reproduction available. Mounts to the door jamb and keeps water from going into the quarter panel. Sold as a pair. Replaces Ford part #: C7ZZ-6528182 and C7ZZ-6528183

Leaf spring front bolts for any 1967 Mercury Cougar or Ford Mustang. For some reason the 1967 bolts are a bit longer than later years. AMK F-1065, About 6-1/2 inches long. 6 total pieces, 2 bolts, 2 heavy washers, 2 nuts.

If these drain plugs are absent mice will be able to find their way into your car. Sold as a pair. Replaces Ford part #: C7ZZ-6511202-A.

These keep the trunk hinge spring rods from rattling. These are a reproduction of the anti-rattler for 67-68 Cougar / 65-68 Mustang.   Replaces Ford part # C5ZZ-6545028. These also work for the 69-70 Cougar / Mustang better than what came factory, which, according to the Ford MPC, for 69-70 would have actually been 1/8" x 7/8" Vinyl Foam Weatherstrip Tape, Ford part C6AZ-19627-A. Check out our trunk torsion bar installation video: ...

NOTE: At the moment the supplier is only making the late model version of this beltline kit. The late version has a slight bend in the chromed quarter piece, whereas the early version is straight (see photo above). Made With Exact Materials As Original. Eight piece kit that includes inner and outer belt-line, enough for both pieces of door and quarter glass. These strips run horizontally against your glass and keep water and debris from entering your rear quarter panels and doors causing them...

Reproduction 3/8" fuel line to side apron grommet for the Mercury Cougar or Ford Mustang.Replaces Ford part # C7ZZ-9288.

C7ZZ-5482-B This is a factory used front sway bar. This is the same size 3/4 inch diameter as the 289 and 302 sway bar but has a slight difference in the bends for the 1967 390-4V or 6.5Liter engines. This bar was factory identified with a One-Yellow and One-Blue paint stripe. This factory used front sway bar, does not include any mounting brackets or end link kits.

Restored six piece anodized aluminum front moulding / trim set for the Mercury Cougar. We suggest you make the order online and then send your cores with a copy of your invoice. Once your cores arrive we will ship the restored set.  If you do not have good cores we do have them for sale. These restored original trim parts have the correct satin "bright dip" anodized finish and look like NOS! We have sold hundreds of these trim parts to Cougar owners all over the world, many of which are...

Restored six piece anodized aluminum front moulding / trim set for the Mercury Cougar. We suggest you make the order online and then send your cores with a copy of your invoice. Once your cores arrive we will ship the restored set.  If you do not have good cores we do have them for sale. These restored original trim parts have the correct satin "bright dip" anodized finish and look like NOS! We have sold hundreds of these trim parts to Cougar owners all over the world, many of which are...

Sold individually. Has correct flattened area at top. Competition handling size, measures 7" from inner radius to end of threads. Thread size 7/16-20".  Does not include the OEM style nuts, those are an optional addon.  Replaces Ford Part #: C6OA-5705-C

Steel freeze plug or expansion plug set for any Ford 390 / 427 / 428CJ engine. 1967-70 Mercury Cougar and 1967-70 Ford Mustang. 17 piece set with threaded screw in plugs as shown. 

Fuel pump drive eccentric for most small block Ford engines 1963-72. Including 221, 260, 289, 302, and 351W. Used eccentric from our wrecking yard. Includes eccentric, bolt, and washer. 2-1/2 inches in diameter.Ford part number C3AZ-6287-B.

Used rear leaf spring retainer for 1967 -73 Mercury Cougar with competition handling or GT suspensions. Additionally it fits 1966-71 Mercury Comet / Montego / Cycolne, 1966-71 Ford Fairlane / Torino, all with HD or GT suspensions. Identified with a stamped number "2" on the top. The inside height is 1-29/32 or 1.91 inches. Sold individually, one for each side for a total of 2 per car. Bead blasted for pictures, most will ship 'as removed'. This suspension part never came painted, there will be...

NOS driver side (left hand) fender extension moulding / trim for the Mercury Cougar. These NOS parts will almost always show some amount of shelf wear and often the tooling was near the end of its life so do not be alarmed when you find the fit and finish is not as good as our restored trim.Ford part # C7WY-16075-A.*NOTE* Keep in mind we buy most trim and mouldings found on a Cougar.

NOS passenger side (right hand) hood lip moulding / trim for the Mercury Cougar. These NOS parts will almost always show some amount of shelf wear. The tooling was often near the end of its life, so do not be alarmed when you find the fit and finish is not as good as our restored trim.Ford part # C7WY-16856-A.*NOTE* Keep in mind we buy most trim and mouldings found on a Cougar.

Core driver side (left hand) hood lip moulding / trim for the Mercury Cougar. Good used core with minor dings, scratches, and dullness.Ford part # C7WY-16855-A.

Core passenger side (right hand) hood lip moulding / trim for the Mercury Cougar. Good used core with minor dings, scratches, and dullness.Ford part # C7WY-16856-A.*NOTE* Keep in mind we buy most trim and mouldings found on a Cougar.