Heater with Air Conditioning & Air Conditioning Components

Complete heater and air conditioning control assembly that includes a bezel or face plate, knobs, bracket control mounting plate, electrical and vacuum switches. Functional, driver quality, heater control assembly for your Mercury Cougar and Ford Mustang until 1-3-1972. Does not include the indicator light plug and harness. Ford part # D1ZZ-19A884-A. *Restoration Tip* You can purchase some plastic polish (or try toothpaste) and polish for the lens back to new. Find a silver paint pen...

Complete heater and A/C control assembly includes bezel or face plate, bracket control mounting plate, electrical and plastic vacuum switches. Functional, driver quality, heater control assembly. This unit is for 1972-73 Cougars and Mustangs produced after 1-3-1972. The prior years 1971-72 assembly without the plastic vacuum switch assembly will fully interchange with this unit. Knobs and light socket wiring harness not included. Ford part # D2ZZ-19980-A. *RESTORATION TIP* If you like to...

This is a used A/C center vent attaching clip. Two required per center AC vent, the two tiny tabs fit in the holes on the sides of the vent assembly and when you tighten the Phillips screw it will pull the vent tight against the dash pad. Very hard to come by, others have used silicone to bond the chrome vent in place when clips could not be found.Replaces Ford part number C7AZ-14570-A.

NOS long shaft bearing for use on all 289, 302, or 390 engines. After 50 years of heat and use, many idler adjusting bearings have seized or are on their way out. This is your answer! This part requires a press to install it. Bearing surface is 1-7/16", bearing diameter is 1.180".  Shaft length (sticking out of bearing) 1 1/8" Ford numbers C4AZ-2990-A, C4AA-2A898-A. ...

Repair your own idler / tensioner with our bearing for use on all 289, 302, or 390 engines. After 50 years of heat and use, many idler adjusting bearings have seized or are on their way out. This is your answer! This part requires a press to install it. Bearing surface is 1-7/16", bearing diameter is 1.180".  Shaft length (sticking out of bearing) 1 1/8"Overall length 2-3/4" Ford numbers C4AZ-2990-A, C4AA-2A898-A. ...

Repair your own idler / tensioner with our kit which includes a dust cover and is for use on all 289, 302, or 390 engines. After 50 years of heat and use, many idler adjusting bearings have seized or are on their way out. This is your answer! This part requires a press to install it. Bearing surface is 1-7/16", bearing diameter is 1.180".  We have had a machinist shorten the shaft on these bearings so that they are easily pressed into the cast pulley brackets that use the short...

Grade A used A/C center vent for XR7 (non Standard) model Cougars. These will have some minor chrome blemishe in the plating, but no heavy pitting or damage. Fits the XR7 model (65B) Cougars with woodgrain dash faces. See our other listing for Grade B versions of this air conditioning center register or vent. *Note - Will not fit Standard model Cougars. Replaces Ford number C7WY-19893-D.

Reproduction A/C center vent for XR7 (non Standard) model Cougars. These are great quality vents with bright chrome finish. Fits the XR7 model (65B) Cougars with woodgrain dash faces. *Note - Will not fit Standard model Cougars. Replaces Ford number C7WY-19893-D.

Grade B used 1968 Mercury Cougar air conditioning chrome bezel, naked as shown. Some blemishes as shown. No extra parts included, levers and switches available. Does not come with the 1968 only detachable air vent. The 1968 Cougar electrical assembly manual indicates that this is part of C8WA-19A976-F Register and Control assy. (Bright Finish). Bright finish is Cougar, Ford Mustang bezels had black pebble grain or wood grain finishes attached. Ford casting number on reverse of this piece is...

Grade A used A/C center vent for standard (non XR7) model Cougars. These will have almost perfect chrome plating, minor blemishes only, no major pitting. Fits the standard model (65A or 65C) Cougars with padded dash face pads. See our other listing for Grade B versions of this air conditioning center register or vent.*Note - Will not fit XR7 model Cougars.Replaces Ford casting number C7WA-19623 and C7WY-19893-A.

Grade B used A/C center vent for standard (non XR7) model Cougars. These will have some defective chrome plating, and pitting. Fits the standard model (65A or 65C) Cougars with padded dash face pads. See our other listing for Grade A versions of this air conditioning center register or vent.*Note - Will not fit XR7 model Cougars.Replaces Ford casting number C7WA-19623 and C7WY-19893-A.

Reproduction A/C center vent for standard (non XR7) model Cougars. These are great quality vents with bright chrome finish. Fits the standard model (65A or 65C) Cougars with padded dash face pads. *Plastic chrome vent plate included.*Note - Will not fit XR7 model Cougars.Replaces Ford casting number C7WA-19623 and C7WY-19893-A.

Grade B used A/C center vent for XR7 (non Standard) model Cougars. These will have some defective chrome plating, and pitting. Fits the XR7 model (65B) Cougars with woodgrain dash faces. See our other listing for Grade A versions of this air conditioning center register or vent. *Note - Will not fit Standard model Cougars. Replaces Ford number C7WY-19893-D.

Lower dash bezel to the left of the steering column. This one is for those 1971-73 Mercury Cougars with factor air conditioning. Cars with only the heater option used a different bezel that has a hole for the vent cable. This bezel is blank, and only has the rectangular hole for the air conditioning vent register.Replaces Ford part number D1WB-65044A13-BC (cast on the part) or D1WY-6504393-B

Used heater blower motor for very late 1967 and all 1968 Mercury Cougars and Ford Mustangs with integral or factory air conditioning. The tell tale sign is the early motors have a nipple of attaching the rubber elbow. This later version has a round hole for attaching a different rubber elbow. These are good used original FoMoCo units and have the correct pigtails in place. This used unit also carries a one year warranty compared to the reproduction that carries a 30 day warranty. The mounting...

Used heater blower motor for Mercury Cougars and Ford Mustangs with integral or factory air conditioning. These are good used original FoMoCo units and have the correct pigtails in place. This used unit also carries a one year warranty compared to the reproduction that carries a 30 day warranty. The mounting plate is included and mounted to the motor. On the reproduction units, the mounting plates are sold separately. These are the 1969-70 variety, which have specific colored wires and leads....

Used heater blower motor for Mercury Cougars and Ford Mustangs with integral or factory air conditioning. These are good used original FoMoCo units and have the correct pigtails in place. This used unit also carries a one year warranty compared to the reproduction that carries a 30 day warranty. The mounting plate is included and mounted to the motor. On the reproduction units, the mounting plates are sold separately. These are the 1971-73 variety, which have specific colored wires and leads....

Used heater blower motor for 1967 Mercury Cougars and Ford Mustangs with integral or factory air conditioning. The tell tale sign is the early motors have a nipple of attaching the rubber elbow. Later version has a round hole for attaching a different rubber elbow. These are good used original FoMoCo units and have the correct pigtails in place. This used unit also carries a one year warranty compared to the reproduction that carries a 30 day warranty. The mounting plate is also included. On...

Used mounting bracket from a 1967-68 Mercury Cougar or Ford Mustang with factory installed air conditioning. This is the tab that is riveted to the blower housing, the stud goes through the firewall. Bracket with stud only, no other hardware included. Normally this will ship with the old fiberglass remnants still riveted to this bracket. 

Used mounting bracket from a 1971-73 Mercury Cougar or Ford Mustang with factory installed air conditioning. This is the tab that is riveted to the blower housing, the stud goes through the firewall. Bracket with stud only, no other hardware included. Normally this will ship with the old fiberglass remnants still riveted to this bracket. 

Used bracket or mounting tab that often gets lost when servicing the air conditioning plenum. Attaches to the box with two screws and has stud that goes through the engine firewall for mounting the A/C box assembly under the dash. Basically the same part as found on 1967-68 brackets, but this one has a slightly longer stud. Replaces Ford part number C9ZZ-18A456-A.

Used bracket or mounting tab that often gets lost when servicing the air conditioning plenum. Attaches to the box with two screws and has stud that goes through the engine firewall for mounting the A/C box assembly under the dash. Basically the same part as found on 1969-70 brackets, but this one has a slightly shorter and pointed stud. Replaces Ford part number C7ZZ-18A456-A.

1967 Cougar and Mustang tubular steel brace. Connects and supports the rear of the air compressor to the factory intake manifold. From what we can tell there is no difference 67 to 68.Ford part # C7ZZ-2889-A.

Used bracket for installing the defrost nozzles assembly to the dash on all 1969-70 Mercury Cougar or Ford Mustang with factory air conditioning. Bracket only, no attaching hardware.

This is used on Mercury Cougars and Ford Mustangs equipped with factory A/C. This is the bracket for the valve that stops the flow of warm coolant when A/C is turned on. This is an exact reproduction and has the zinc dichromate finish.

This bracket clamps the liquid fitting on the liquid hose to the discharge hose on the inside of the radiator support. It's purpose is to keep the lines from moving around during operation.

Two of these little plastic protectors came on Mercury Cougars and Ford Mustangs equipped with Air Conditioning. They are affixed to the front cross member using the same bolts that holds your condenser in place. Their purpose was to protect the wiring harness from potential damage if the car were to get into a collision. These are very hard to find today as most were discarded the first time the condenser was replaced. Even your most experienced judges usually have never seen or heard of this...

Used rubber bumper that fits into the bracket in the bottom center of the door shell. Fits all 1967-68 Mercury Cougar and 1965-68 Ford Mustangs. This is the rubber bumper for the window rest when the door glass is at its lowest. Bracket is in bottom of the center of the door. Fits both right and left doors. Correct for 1967 - 1968 but will work in 1969 - 1970 with Bolt-in glass if you cut it down. Sold separately, two required per car. Replaces Ford part # C5ZZ-6521762-B  Check out...

Nice reproduction fresh air vent cable pull assembly. Comes with dash mounted bracket as shown. Much stronger construction than the originals, which were made with a plastic sleeve instead of metal.Replaces Ford part number C7ZZ-6501891-A and C7ZZ-6501891-C.

These were a very poor design and most break where they mount to the bracket. We also have this in the service replacement version with the improved metal housing, very tough part for us to keep in stock. The metal version is a better part and you can get our metal reproduction unit right here!Ford part # C7ZZ-6501891. ...

Under dash bracket used to mount the pull cable for the fresh air vent on the driver side of your Mercury Cougar or Ford Mustang.

Grade A used A/C center vent for any 1969-70 Mercury Cougar. These will have almost perfect chrome plating, minor blemishes only, no pitting. Fits all models of 1969 and 1970 Cougar. See our other listing for Grade B versions of this air conditioning center register or vent. Limited to stock on hand. Does not come with attaching clips, see 'related' tab. Rear dimensions: 6-1/4 x 2 inches. Alternately, this center vent can be installed in a 1969-70 Ford Mustang. Similar dimensions, doesn't have...

Grade B used A/C center vent for any 1969-70 Mercury Cougar. These will have some blemishes, or pitting. Fits all models of 1969 and 1970 Cougar. See our other listing for Grade A version of this air conditioning center register or vent. Does not come with attaching clips, see 'related' tab.  Rear dimensions: 6-1/4 x 2 inches. Alternately, this center vent can be installed in a 1969-70 Ford Mustang. Similar dimensions, doesn't have the small angle bend. C9ZZ-19863-A or C9ZA-19C683-A....

Black plastic air conditioning center vent register bezel for any 1971-73 Mercury Cougar or Ford Mustang with Factory installed or integral A/C. Mounts Horizontally in the dash panel. Individual vents roll 360 degrees to blow air straight or to the sides. For that extra level of detail, we suggest using a silver paint pen for detailing the silver edges. Ford part number D1ZZ-19893-A.

Used air conditioning distribution chamber. Comes as shown, plastic housing, internal flapper door with rod, with attached bracket for attaching vacuum actuator. Actuator, lever, switch, and hardware sold separately. Unbroken condition, it will definitely need new foam on the door. Stapled foam seal to center vent may not be perfect.Replaces Ford part number C7ZA-19740-B.

Used air conditioning distribution chamber. Comes as shown, plastic housing, internal flapper door with rod, with attached bracket for attaching vacuum actuator. Actuator, lever, and hardware sold separately. Unbroken condition, it will definitely need new foam on the door.Replaces Ford part number C9ZZ-18471-A.

Used air conditioning distribution chamber. Comes as shown, plastic housing, internal flapper door with rod, with attached bracket for attaching vacuum actuator. Actuator and hardware sold separately. Unbroken condition, it will definitely need new foam on the door.Replaces Ford part number D1ZZ-18471-A.

25 AMP circuit breaker for all 1968 Mercury Cougars and Ford Mustangs with factory air conditioning. Mounts on the panel, under the dash, next to the fuse block. This particular breaker was also used on the ASC installed 1968 sunroofs. It is 1.07" x 0.40" and has a single green and red dot. Box is marked Tung Sol, 25AMP 12V, and made in the U.S.A. Electrical schematics list this circuit breaker. Ford part # C8ZB-14526-A, C8ZZ-14526-A.

These are used hose clamps that bolt to the body and lateral A/C bracket. These were dipped in a rubber like substance to prevent chaffing. The ones that we have available may have some cracking or damage to this coating. It should be easy to 'dip' them again with the product that is available in most hardware stores. We normally see 2 of these clamps, securing the hoses on most cars. Replaces Ford part number 374125-S100.

This A/C tag clip fastens the aluminum tag to top of the A/C pump.

Clips that attach to the dash for mounting the defrost nozzles. Package of 4 clips and 4 nuts, enough for non air conditioned cars, same clips used for air conditioned cars. Cars with A/C only need 3 clips installed though. Nuts are different than OEM, but work fine, we suggest adding a flat washer though.

Clips that attach to the dash for mounting the defrost nozzles. Package of 3 clips and nuts. Good for cars with or without A/C. Typically found on 69-73 cars, but will also fit and work on 1967-68 as well.Replaces Ford part number 357849-S100.

Core used set of Eaton clutch brushes, we save these because of the FoMoCo stamped bracket with Ford part number C7AA-2979-A. It is possible to reuse the FoMoCo stamped bracket from the originals and re-rivet to reproduction version. Yes, you can make it sneaky concours. You would have to figure out the rivets though. See related items for NEW Eaton brushes. Pitts compressor clutch is the most common one starting in 1969. Replaces Ford part #: C5ZZ-2979. C7AA-2979-A ...

This set of brushes only fits the Eaton brand of air compressor clutch. These are exact reproductions made from the original tooling. It is possible to reuse the FoMoCo stamped bracket from the originals and re-rivet to this version. Yes, you can make it sneaky concours. You would have to figure out the rivets though. See related items for core brushes with stamped Ford numbers. Pitts compressor clutch is the most common one starting in 1969. Replaces Ford part #: C5ZZ-2979. C7AA-2979-A ...

This unit is for Mercury Cougars and Ford Mustangs, is pre-assembled, and includes the drier and all brackets.

Our new high performance condenser kit comes pre-assembled with the drier and all brackets. 1967 - 1968 condenser shown. These condensers are one of the highest performing, durable condensers available in today's automotive market. This condenser was designed specifically to increase heat transfer for lower head pressures during idle situations, allowing more airflow to pass through the condenser and give the radiator enough airflow to operate properly. Remember to remove your coupler...

Original used factory air conditioning coupler for all 1967-73 liquid line or sight glass hoses. Brass construction, includes the plunger and spring. Sold as a two piece kit which includes the male and female components. Replaces Ford part number C1SZ-19B596-A and C1SZ-19B595-A.Components also sold individually.

Original used male half of the factory air conditioning coupler for all 1967-73 liquid line or sight glass hoses. Brass construction, includes the plunger and spring. Also sold as a two piece kit which includes the male and female components. Replaces Ford part number C1SZ-19B595-A.