A/C Vent Ducts / Registers / Controls / other Parts

Used push in retainer for any 1967-73 Mercury Cougar or Ford Mustang. These fasteners are used to attach the floor vent / duct to the blower housing, and to connect the defroster assembly to the blower housing, etc. Sold individually.Replaces Ford part number 380464-S.

Used elbow or connector for the passenger side air conditioning register. This connects the duct tube to the louvered vent. Fits any 1971-73 Mercury Cougar and Ford Mustang. Comes with one metal clip as shown for connecting to the register vent.Replaces Ford part numberD1ZZ-19C692-A. The number from the assembly manual is D1ZA-19C677-AA.

Used elbow or connector for the driver side air conditioning register. This connects the duct tube to the louvered vent. Only fits 1971-73 Mercury Cougars.Replaces Ford part number D1WY-19C692-A.

Used retaining spring and two screws for attaching the break away air conditioning vents to any 1968 Mercury Cougar or Ford Mustang with factory installed A/C.

This reproduction knob set is made by Scott Drake Enterprises. Unlike our knobs, these units have a much larger font. Considering the average Classic Mustang owner is probably 50 years old or more, this was a pretty good idea to do them in this manner since the originals are rather hard to read while driving. If you want user friendly, then this is a very nice upgrade. If you want correctness, then our other set is what you will want. Either way, we got you covered.

All new parts for rebuilding the right and left shutoff butterfly in the air conditioning register vents. Fits all 1967-68 Mercury Cougar and Ford Mustang with factory A/C. Kit includes 2 knobs, 2 black butterfly vent doors, 2 shafts, and 2 retainers. All of these individual parts are also separately. Chrome vent registers and vent retainers are also available.

Used strap or support bracket for the foam air conditioning vent tube going to the driver side A/C vent. The electrical assembly manual indicates that this strap bracket behind the dash on the driver side. Our findings from the wrecking yard show that 1967 is typically rubber coated, 1968 is bare steel. Please specify is you have a preference. The rubber coated ones will show some deterioration, plan on re-dipping or use as-is. Not exactly the same as the support for the passenger side.Ford...

Plunger switch that mounts to the air distribution manifold behind the center A/C vent. A mechanical lever operates the switch when the air damper is in the proper location to distribute air through the center air conditioning vent of the dash. This switch controls the clutch on the A/C compressor. 1967-68 Mercury Cougar and 1966-67 B Body Ford, Fairlane, Ranchero, and C Body Mercury Comet and other variations Cyclone etc. Tested and working switch. On Cougar and Mustang it attaches to the...

This reproduction A/C fan switch mounts to the rear of the factory installed air conditioning ventilation control panel.  Save your knobs or consider purchasing the 1969-73 selector button kit, you can find them here.Ford part # C9ZZ-19986-A.

This A/C fan switch mounts to the rear of the factory installed air conditioning ventilation control panel. We always test all of our electrical components and this is a good working switch and wiring pigtail with plug. Save your knobs or consider purchasing the 1969-73 selector button kit. Click this LINK for those little beauties.Ford part # C9ZZ-19986-A.

This used A/C fan switch mounts to the rear of the factory installed air conditioning ventilation control panel on your Mercury Cougar or Ford Mustang. Good working switch and wiring pigtail with plug. Save your knobs or consider purchasing the 1969-73 selector button kit.Ford part # D1ZZ-19986-A.

Mounts to the rear of the factory installed air conditioning ventilation control panel on Mercury Cougar and Ford Mustang. Good working switch and wiring pigtail with plug. Save your knob or consider purchasing the 1967 selector button kit.Ford part # C7ZZ-19986-A.

This used A/C fan switch mounts to the rear of the factory installed air conditioning ventilation control panel on 1968 Mercury Cougar and Ford Mustang. Good working switch and wiring pigtail with plug. Save your knob or consider purchasing our 1968 selector button kit.Ford part # C8ZZ-19986-A.

Used vacuum actuator for controlling the center A/C vent on certain 1969-70 Mercury Cougar or Ford Mustang. This is a bare vacuum valve, that does not have the screwed on extension which make the unique part numbers from the Ford MPC. Tested and holds vacuum. This is the unique valve with two separate vacuum ports. 2 ports for two different positions. Studs are on 1-1/4 inch centers. Common single port vacuum valve is on 2-1/4 inch centers. Ford part number C9ZZ-18A318-A. ...

Used vacuum actuator for controlling the center A/C vent on any 1971-73 Mercury Cougar or Ford Mustang. This is a bare vacuum valve, that does not have the screwed on extension which make the unique part numbers from the Ford MPC. Tested and holds vacuum. This is the unique valve with two separate vacuum ports. 2 ports for two different positions. Ford part number D1ZZ-18A318-A.

Vacuum switch that attaches to the air conditioning lever assembly on all 1967-68 Mercury Cougar and Ford Mustangs with integral A/C.Ford number stamped C7ZA-19B919.

Used vacuum switching manifold and electrical micro switch assembly from a 1969 to early mid 1972 Mercury Cougar and Ford Mustang. This is the all metal version vacuum distribution block. 1972 owners, please check your A/C controller to verify if you have or need the plastic version of this switch. This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of 50% of our web price for parts...

Used vacuum switching manifold and electrical micro switch assembly from a mid to late 1972 through 1973 Mercury Cougar and Ford Mustang. This is the plastic version with riveted micro switch. We test the micro switches prior to shipping. Please check your A/C controller to verify that you have and need the plastic version of this switch. We also have the all metal version with separate micro switch which can be interchanged, but you would need a micro switch.Ford number D2ZA-19B919-A or...

Here is our used vent louver for your Mercury Cougar or Ford Mustang.

Each vent has only one of these louvers with the protruding knob.

This is a complete working assembly with outer housing. Fits driver and passenger side dash outlets, on any 1971-73 Mercury Cougar or Ford Mustang. We sell the louvers individually if your assembly is not broken and all you lack is a couple of missing fins. The fins are easily replaced as they just snap in place. The vent housing has a Ford casting number or D1ZA-6501820. Fits both the right and left sides of the dash. Center vent is different.Ford part # D1ZZ-18C366-A.

Used Grade A Windshield Defroster Nozzle for any 1969-70 Mercury Cougar or Ford Mustang with factory air conditioning. Grade A will be free from physical defects, may have a minor scuff or scratch.Replaces Ford part number C9ZZ-18490-B.

Used Grade B Windshield Defroster Nozzle for any 1969-70 Mercury Cougar or Ford Mustang with factory air conditioning. Grade B will have a small crack or chip, or possibly a broken mounting tab.Replaces Ford part number C9ZZ-18490-B.

Defrost or defroster duct for the windshield on all 1967-68 Mercury Cougar and Ford Mustangs with factory A/C or air conditioning. This Grade A version will be free of all but very cosmetic defects. Meaning no broken tabs, or torn or missing screens. Replaces Ford part numbers C7ZA-18490-E and C8ZA-18490-B.*Note - Only fits those cars with factory or integral air conditioning. Cars with heaters only used two individual nozzles.

Defrost or defroster duct for the windshield on all 1967-68 Mercury Cougar and Ford Mustangs with factory A/C or air conditioning. This Grade B version may have one of the following: crack or chip, have a broken tab, or a torn or missing screen. B grades will install and work, they just may need a bit of duct tape or be held on with 3 of the 4 screws.Replaces Ford part numbers C7ZA-18490-E and C8ZA-18490-B.*Note - Only fits those cars with factory or integral air conditioning. Cars with...

Under dash wiring harness assembly for all 1967 Mercury Cougar and Ford Mustangs with integral, or factory installed air conditioning. All wiring harnesses are test and inspected by our electrical department.Replaces Ford part number C7ZB-19945-A.

Under dash wiring harness assembly for all 1968 Mercury Cougar and Ford Mustangs with integral, or factory installed air conditioning. All wiring harnesses are test and inspected by our electrical department.Replaces Ford part number C8ZB-19945-B.

Used heater control wiring harness for the 1971 Mercury Cougar without A/C. Runs from the blower switch to the resistor box.

Used heater control light wiring harness for the 72 - 73 Cougar with A/C.

Vacuum switch not included. This control switch lever assembly only, for the vacuum and damper door consists of the two lever assembly for the vacuum and cable actuation of the A/C plenums damper doors on Mercury Cougar and Ford Mustang with integral A/C.Ford part # C7ZZ-19B888-A.

This is a blemished piece that we're offering at a discount. We received a shipment of these vents with some issues with the chrome finish. The flaws are visible in direct light but probably not noticeable when installed. Fit and function is the same as our premium units. See example photo for a closeup of the imperfect chrome finish.

Used air conditioning vent for any 1968 Mercury Cougar or Ford Mustang with factory installed A/C. These are different than the 1967 A/C vents. For 1968 the vents detached from the main housing for safety reasons. These were meant to 'break away' in the event of an accident. These attach to the housing with a spring, spring sold separately. Grade A is in limited quantities and will have very good chrome, there will be some minor blemishes found under close scrutiny. B grade versions also...

Grade A used 1968 Mercury Cougar air conditioning chrome bezel, naked as shown. Very minor blemishes, almost insignificant as shown. No extra parts included, spring is available. Does not come with the 1968 only detachable air vent. The 1968 Cougar electrical assembly manual indicates that this is part of C8WA-19C784-A Register and Bezel. (Bright Finish). Ford casting number on reverse of this piece is C8ZA-19C784. Mustang used a shorter bracket, on the reverse you can see the witness line and...

Original retainer for the passenger side A/C vent on Mercury Cougars and Ford Mustangs with equipped with factory A/C. Necessary for correctly installing the upper fastener of the vent.Ford part # C7ZA-19A950-A.

This is a blemished piece that we're offering at a discount. We received a shipment of these vents with some issues with the chrome finish. The flaws are visible in direct light but probably not noticeable when installed. Fit and function is the same as our premium units. See example photo for a closeup of the imperfect chrome finish.This reproduction A/C vent register with knobs is a perfect fit for your Mercury Cougar or Ford Mustang / Shelby. Includes all three control knobs. *NOTE* Mustang...

Passenger side air conditioning register vent with slight manufacturer blemishes. See photos for details.

This is a blemished piece that we're offering at a discount. We received a shipment of these vents with some issues with the chrome finish. The flaws are visible in direct light but probably not noticeable when installed. Fit and function is the same as our premium units. See example photo for a closeup of the imperfect chrome finish. This new reproduction is a spot-on replica of the 1967 passenger side AC vent! It differs from 1968 only in that 1968 used a break-away vent...

Grade A used passenger side air conditioning vent register for 1967 Ford Mustang with standard (non-deluxe) interiors. This one has the factory pebble grain or camera case finish. Very nice used, only have the one available. We also have several Mustang center vents available with the pebble graining.Replaces Ford part number C7ZA-19893. This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store...

This new reproduction is a spot-on replica of the 1967 passenger side AC vent! It differs from 1968 only in that 1968 used a break-away vent that was very prone to failure. This is a fixed, one piece body and will not fall apart. This will be a direct fit to your 1967 and 1968 Ford Mustang with no modification needed. Dealer pricing available. *NOTE* Mustang used the shorter version of this vent than the Cougar did, otherwise they are visually and mechanically the same. Click on images to...

Normally we do not list Mustang specific parts, but since we are the distributor for these new reproductions, we need to have them accessible via our web site to all. This kit is the same as a Mercury Cougar set with the exception that the passenger side is shorter on the Mustang / Shelby than the Cougar. Top quality chrome finish and precision fit worthy of the most scrutinized restoration. Remember when we used to spend hundreds of dollars for "decent" used examples and then take a risk with...

Normally we do not list Mustang specific parts, but since we are the distributor for these new reproductions, we need to have them accessible via our web site. This kit is the same as a Mercury Cougar set with the exception that the passenger side is shorter on the Mustang / Shelby than the Cougar. Top quality chrome finish and precision fit worthy of the most scrutinized restoration. Remember back in the day when we used to spend hundreds of dollars for "decent" used examples and or take a...

A Complete A/C and heater control assembly that includes a bezel or face plate, knobs, bracket control mounting plate, electrical and vacuum switches. Check back often, this type and grade of part is seldom in stock very long.Ford part # C7WA-19980-A.

A Complete A/C heater control assembly that includes a bezel or face plate, knobs, bracket control mounting plate, electrical and vacuum switches. Check back often, this type and grade of part is seldom in stock very long. Ford part # C8WA-19980-A.

A/C and heater control bezel or face plate. Grade A- used condition, standard pebble grain trim. Check back often, this type and grade of part is seldom in stock very long.Bezel only, no levers or switch.Ford part # C7ZA-19C705.

Grade A used 1968 Mercury Cougar air conditioning chrome bezel, naked as shown. Very minor blemishes, almost insignificant as shown. No extra parts included, levers and switches available. Does not come with the 1968 only detachable air vent. The 1968 Cougar electrical assembly manual indicates that this is part of C8WA-19A976-F Register and Control assy. (Bright Finish). Bright finish is Cougar, Ford Mustang bezels had black pebble grain or wood grain finishes attached. Ford casting number on...

Grade A used A/C center vent for any 1969-70 Ford Mustang. This will have almost perfect chrome plating, minor blemishes only, no pitting. Fits all models of 1969 and 1970 Mustang. Limited to stock on hand. Does not come with attaching clips, see 'related' tab. Rear dimensions: 6 x 2-1/4 inches. Replaces Ford casting number C9ZZ-19863-A and C9ZA-19C683-A.

Grade B used A/C center vent for any 1969-70 Ford Mustang. This will some limited chrome pitting in the plating. Fits all models of 1969 and 1970 Mustang. Limited to stock on hand. Does not come with attaching clips, see 'related' tab. Rear dimensions: 6 x 2-1/4 inches. Replaces Ford casting number C9ZZ-19863-A and C9ZA-19C683-A.

Used rear window defog switch and knob assembly with mounting bracket for the 71 - 73 Standard Cougar.