All Available Parts - Other Ford/Mercury

New Bolt kit, for the installation of a water pump on any Ford 352, 390, or 428CJ engine. Fits all 1967-70 Mercury Cougar and Ford Mustang with 390-4V, 390-2V, and 428 Cobra Jet engines.

New Bolt kit, for the installation of a water pump on any Ford 351C or 351 Cleveland engine. Fits all 1970-74 Mercury Cougar and Ford Mustang with 351C, 351CJ engines. 11 total pieces in the kit as shown.

New Bolt kit, for the installation of a water pump on 1970-73 Ford 302, Boss 302, or 351W engine. Fits all 1970 Mercury Cougar and 1970-73 Ford Mustangs. 9 total pieces in the kit as shown.

Reproduction steering gear or seat belt washer for the Mercury Cougar or Ford Mustang. These units are sold individually.Replaces Ford part # 378580-S.

This emblem was used on the driver side of the 1971 - 1972 Cougar hood and on the passenger side of the trunk lid in 1967 - 1968. Also used on various other Mercury products like the Comet, Cyclone, and Marquis prior to 1973. This will not fit on the fender extension of the 1967- 1968 Cougar. Fantastic quality part... In our experience, we have found that you would have to obtain several NOS emblems before you found one with chrome as nice as this. The quality on these new emblems is very...

Refurbished pair of door lock cylinders and ignition cylinder for all double cut key Fords 1970-73. These are coded to the original key code, which was stamped onto one of the door lock cylinders. Sometime after 1973, Ford changed the ignition lock cylinder end. We know it works through 1973, not sure of the change. It must fit the brass lock gear at the bottom of the cylinder hole in the side of the steering column. Refer to your shop manual for removal and installation. Includes two...

Pair of reproduction door pull straps for the 1969 - 1970 Mercury Cougar. Keep in mind that between 69 and 70 there were two different versions of each color. For example, 1969 had the dark green and 1970 had a lighter green...so be sure to order the correct year!

Reproduction manually adjustable convex passenger side view mirror in chrome for the Mercury Cougar or Ford Galaxie. Gasket and screws included. Replaces Ford part # C7AZ-17696. Dimensions: Base Hole Spacing: 5-7/8" Base Length: 6-5/8" Overall Height: 5-1/8" Mirror Width: 5-1/8" Mirror Height: 3-5/16" Do you have questions about installing a passenger side mirror or using Riv-Nuts? Here’s our little video that will make your mirror installation a little easier. ...

*NOTE* EARLY 69's USED THE 2112 MIRROR FOR BOTH PASSENGER AND DRIVER SIDES. LATE 69's USED TWO DIFFERENT SIZES FOR EACH SIDE (2124 for driver side, and 2112 for passenger side). BEFORE ORDERING, PLEASE CHECK YOUR DIMENSIONS AND COMPARE TO OUR LISTINGS. Precision cut replacement lens for any Ford product with sport mirror on the passenger side. This fits any FoMoCo Sport mirror 69 and up, left hand only. Comes with two round pieces of double sided tape. Keep in mind if your lens is bad and it...

Reproduction passenger side (right hand) sport mirror lens for the Mercury Cougar or Ford Mustang and Torino.The mounting screw, that holds the mirror assembly in, is not included by default but is an optional addon. Replaces Ford part # C9AZ-17698-B. Dimensions: 4 7/16" x 2 15/16" This version does NOT include the wording "objects in mirror are closer than they appear". We also sell the version with the wording. Do you have questions about installing a passenger side mirror or using...

Empty shell / head / housing only for a passenger side manual adjust mirror. Found on all FoMoCo products utilizing a manual mirror 1969 - 1973. The remote mirror heads found on many 1970's Ford products do not interchange with the manual "Bullet Style" mirrors. Most customers find our reproduction unit to be a better value as it comes with the mirror and mounting hardware. Do you have questions about installing a passenger side mirror or using Riv-Nuts? Have more questions about installing a...

Lens with mounting hardware only for a passenger side manual adjust mirror. Found on all FoMoCo products utilizing a manual mirror 1969 - 1973. The remote mirror lens assemblies found on many 1970's Ford products do not interchange with the manual "Bullet Style" mirrors. Count on the glass being scratched. The value here is in adjustment / mounting hardware. This unit will be guaranteed to keep its adjustment and not be loose like many have become over the years. Keep in mind this item is...

Used passenger side (right hand) sport mirror that is correct for the Mercury Cougar. This will also work on 1969-70 Cougar, but base height is just a little bit taller. *NOTE* We are currently out of good used mirrors with original bases so if you order this part you will get an original mirror with a reproduction base. Do you have questions about installing a passenger side mirror or using Riv-Nuts? Have more questions about installing a passenger side mirror or Riv-Nuts? Got a mirror lens...

Fits and looks identical to the 1970 mirror base but is slightly taller. The difference in height between the two versions is indiscernible to the naked eye. Very nice product, works well with original mirror heads, save your hardware. Do you have questions about installing a passenger side mirror or using Riv-Nuts? Have more questions about installing a passenger side mirror or using Riv-Nuts? Got a mirror lens that flops around in your Sport Mirror every time you hit a tiny bump in the road?...

*NOTE* EARLY 69's USED THE 2112 MIRROR FOR BOTH PASSENGER AND DRIVER SIDES. LATE 69's USED TWO DIFFERENT SIZES FOR EACH SIDE (2124 for driver side, and 2112 for passenger side). BEFORE ORDERING, PLEASE CHECK YOUR DIMENSIONS AND COMPARE TO OUR LISTINGS. Precision cut replacement lens for any Ford product with sport mirror. This fits any FoMoCo Sport mirror 69 and up. Comes with two round pieces of double sided tape.  Lens measures 4 3/8 X 2 7/8. Do you have questions about installing the...

Pair of reproduction door pull straps for the 1969 - 1970 Mercury Cougar. Keep in mind that between 69 and 70 there were two different versions of each color. For example, 1969 had the dark green and 1970 had a lighter green...so be sure to order the correct year!

This reproduction power window relay mounts to the front inner apron on the passenger side just behind the starter solenoid. This relay can also be used for 1969-73 power convertible tops, and 1971-73 power seat.Replaces Ford part #: C8AB-14677-A.Will replace D1AZ-14677-A, AND C1AF-14677-A but will not be an exact fit

100% Concours Correct PCV Tube for the 1968 Mercury Cougar 427 GT-E, Ford Mustang, Fairlane, or Torino with the 428 Police Interceptor, fits either # C6AE or # C7AE Aluminum PI intake manifold. Replaces Ford Part #: C6AZ-6758-B.

A needed part for giving your car a tune-up. PCV Valve fits all years; 289, 302, 351, 390, and 428 CID; V8. *Note - Not technically correct for 390-4V or 428CJ, those originally used a PCV valve with a threaded top, and the 90° elbow - part number C7OZ-6A706-A.

Hot idle compensator valve assembly for many Ford engines with PCV, starting in 1964 through early 1968. Typically found on 1964-66 Ford 260-2V, and 289-2 engines with air conditioning. 1967-68 289-2V, 302-2V and some 390 engines all with air conditioning and PCV or closed emissions. The Ford assembly manual indicates that the Hot Idle Compensator Valve 'T' Assembly, was installed by removing 3/4 inches of the PCV hose, 2-1/4 inches (on center of the PCV valve). See picture for clarification....

NOS ink stamped Ford script. Connects PCV valve to carburetor spacer plate. For all 289-2V, 289-4, 302-2V, and 302-4V engines. Ford part number C6AZ-6A664-N. These were held on with wire clamps, available here. Fits 1967-68 Mercury Cougar and 1966-69 Ford Mustang. *Note – These molded and contoured hoses were designed to work with original style PCV valve (modern 90° PCV valves won't work). Additionally keep in mind that most anything other than period original intake manifolds, valve covers,...

New foam insulation for the lower tube of the steering columns. Can be used on fixed and tilt columns, from 1968-73, on all Mercury Cougars, Ford Mustangs, and most all other Ford steering columns with a lower tube with inside diameter of 1-5/8 inches. The originals have almost always disintegrated. Adhesive probably isn't needed, but we recommend just a little drop of something to hold it in place. This is a dense foam insulation ring. DIY guys, this material can be found in bulk at home...

Used Release Spring for the 1967 - 1973 Mercury Cougar / 1967 - 1973 Ford Mustang 

Used Spring Sleeve Cap for the 1967 - 1973 Mercury Cougar / 1967 - 1973 Ford Mustang 

Used return spring for any 1970 - 1978 Cougar or Mustang Tilt Column. This spring provides return tension on tilt steering wheels.*NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year.

Reproduction 3D printed retainer / friction clip that replaces broken injected plastic shaft retainers on fixed or tilt steering collapsible columns on most FoMoCo products starting in 1968 and through the 70's. These installs on the upper piece of what Ford called the Steering Column Shaft Assembly, also known as the inner steering column collapsible shaft.  The Steering Column Shaft Assembly is the 2 piece shaft that connects the steering wheel to the rag joint. The upper...

Used bracket for mounting a steering column to the instrument panel on any 1970-71 Mercury Cougar or Ford Mustang. Main bracket only, there is also a side support bracket that is also needed. Bracket also used on 1970 full sized Ford and Mercury cars, and 1970-71 Ford Maverick. Tilt and fixed steering columns.Ford part number D0AZ-3676-A.

Used lateral or side bracket for mounting the steering column to the instrument panel on any 1970-71 Mercury Cougar or Ford Mustang. Support bracket only, there is also a large support bracket that is also needed. Tilt and fixed steering columns.Bracket also used on 1970 full sized Ford and Mercury cars, and 1970-71 Ford Maverick.  Ford part number D0ZZ-3B139-A.

Used lateral or side bracket for mounting the steering column to the instrument panel on any 1972-73 Mercury Cougar or Ford Mustang. Hooped support bracket only, there is also a large main bracket that is also needed. Tilt and fixed steering columns. Bracket also used on 1971 full sized Ford and Mercury cars.  Ford part number D1AZ-3B139-A.

Used bracket for mounting the steering column to the instrument panel on any 1972-73 Mercury Cougar or Ford Mustang. Main bracket only, there is also a hooped support bracket that is also needed. Tilt and fixed steering columns. Bracket also used on 1971 full sized Ford and Mercury cars.  Ford part number D1AZ-3676-A.

Used wiring harness retainer bracket for mounting the steering column bracket, on any 1973 Mercury Cougar or Ford Mustang. Retainer only, many of these are missing. Probably not missed, limited to stock on hand. Basic Ford part number 14A163.

Used flat headed stove bolt and nut, for attaching the two steering column mounting brackets together. Brackets for mounting the steering column to the instrument panel on any 1972-73 Mercury Cougar or Ford Mustang. Two needed per installation, sold individually. This is a 3/8-16 square neck bolt and nut. Ford part number 384527-S2.

If you have already begun to install or have installed this item, it is not eligible for return or refund. This is far superior to the switch Ford put out as a service part in the 90's. It is imperative that you clean every part of your old switch out before carefully installing the new switch. It is best to start both ends at the same time at 6 o'clock and meet at the middle at 12 o'clock. It measures 44" in length. *Note - Will not work in the 1970-74 rim blow steering wheels. Backside width...

Brand new flex plate for all 1970-71 Mercury and Ford with 429CJ engines, and C6 transmissions. Comes complete with new starter ring gear installed as shown.

AMK fastener kit for attaching manual transmission clutch Z-bar brackets. 1969-70 Mercury Cougar and Ford Mustang with 390 or 428CJ engines. AMK number F-473.

AMK fastener kit for attaching manual transmission clutch Z-bar brackets. 1969-70 Mercury Cougar and Ford Mustang with 302 or 351 engines. AMK number F-474.

Bolt kit for installing the idler and adjusting pulley on any 1970-73 Mercury Cougar / 1970-73 Ford Mustang or 1970-73 Ford / Mercury with 302, 351W, and 351C engines. 4 bolts 3/8-16x7/8 inch washer head bolts and 1 thick 3/8 washer.  

Used console lid catch. Plastic piece that screws to the underside lid of your late 1970-73 Mercury Cougar or 1970-78 Ford Mustang. Yep, used on Mustang II's, too.  Ford part number D0ZZ-63060A96-B and stamped into the plastic D0ZB-63060A96-B ...

Quality wiring reproduction for Perfect Circle brand of speed controls as found on most 1967-1971 Ford - Mercury - Lincoln automobiles. Main harness with Ford part number 9A840, can be used on a variety of model and years. Harness connects the servo, has grommet for firewall, and connectors under the dash. Jumper wire to the brake pedal.

Single cylinder head from 1969 Mercury Cougar H or M code 351W engines, 351-2V and 351-4V all the same. Sold as a core, needs thorough cleaning and rebuilding prior to use. Typically this cylinder head has 1.84 and 1.54 inch valves, and the chambers measure out at 60-62 cc's. Basic cylinder head number is 6090. Several Ford casting numbers were used, including the common C9OE-6090-A.These weigh 53 lbs. each, and cannot be combined with other items unless shipping truck freight. ...

Single cylinder head from 1970 Mercury Cougar H code 351W engines, 351-2V. Sold as a core, needs thorough cleaning and rebuilding prior to use. Typically this cylinder head has 1.84 and 1.54 inch valves, and the chambers measure out at 60-62 cc's. Basic cylinder head number is 6090. Several Ford casting numbers were used, including the common D0OE-6090-C. 1970 351 Windsor engine, not to be confused with the 351 Cleveland engine from the same year.These weigh 53 lbs. each, and cannot be...

Single cylinder head from 1967 Mercury Cougar with 390-4V engine with California thermactor smog ports. Sold as a core, needs thorough cleaning and rebuilding prior to use. Typically this cylinder head has 2.02 and 1.55 inch valves, and the chambers measure out at 71-74cc's. With stock pistons, these heads will net an approximate compression ration of 10.5:1. Basic cylinder head number is 6090. This is a GT cylinder head with 14 drilled and tapped exhaust bolt holes. Current...

Single cylinder head from 1972 Mercury Cougar with Q code 351C-4V engines. Sold as a core, needs thorough cleaning and rebuilding prior to use. Typically this cylinder head has 2.19 and 1.71 inch valves, and the chambers measure out at 75.4 cc's. These are considered 'Open Chamber Heads'. With stock pistons, these heads will net an approximate compression ration of 8.6:1. Basic cylinder head number is 6090. Several Ford casting numbers were used, including the common D1ZE-6090-GA. 4V in...

Single cylinder head from either a 1968 X code 390-2V or 1969 Mercury Cougar with 390-4V or 390-IP engine. Sold as a core, needs thorough cleaning and rebuilding prior to use. Typically this cylinder head has 2.02 and 1.55 inch valves, and the chambers measure out at 71-74cc's. With stock pistons, these heads will net an approximate compression ration of 10.5:1 (9.5:1 with X code). Basic cylinder head number is 6090. This is a GT cylinder head with 14 drilled and tapped exhaust bolt holes....

Single cylinder head from 1966 Ford with 390-4V engine. Sold as a core, needs thorough cleaning and rebuilding prior to use. These cylinder heads are factory drilled and tapped for thermactos smog tubes. Typically this cylinder head has 2.02 and 1.55 inch valves, and the chambers measure out at 71-74cc's. With stock pistons, these heads will net an approximate compression ration of 10.5:1. Basic cylinder head number is 6090. This is a GT cylinder head with 14 drilled and tapped exhaust...

Single cylinder head from 1966 Ford with 390-4V engine. Sold as a core, needs thorough cleaning and rebuilding prior to use. Typically this cylinder head has 2.02 and 1.55 inch valves, and the chambers measure out at 71-74cc's. With stock pistons, these heads will net an approximate compression ration of 10.5:1. Basic cylinder head number is 6090. This is a GT cylinder head with 14 drilled and tapped holes for exhaust manifolds. These weigh 48 lbs. each, and cannot be combined with other items...

Rebuilt pair of 390GT cylinder heads for a 1968 S code 390-4V engine. Typically this cylinder head has 2.02 and 1.55 inch valves, and the chambers measure out at 71-74cc's. With stock pistons, these heads will net an approximate compression ration of 10.5:1. Basic cylinder head number is 6090. These are the GT exhaust manifolds with 14 drilled and tapped exhaust bolt holes. This cylinder head PAIR has 4 drilled and tapped, thermactor smog holes. Current dates include: 7M28 and 7M29....

Remanufactured OEM Ford Boss 429 and 429 Cobra Jet manual transmission flywheel. Stamped C9AE-C. New ring gear, resurfaced clutch surface. No visible issues, no discoloration from heat. 1971 Mercury Cougar and Ford Mustang, 1970-71 Ford Torino and Mercury Cyclone and variants. 1969-70 Boss 429. Ford part number C9AE-6375-C.

This manual shows exploded diagrams and part numbers of all the motors Ford used in 1967, not just the Cougar. I use this manual almost daily for identifying air conditioning brackets and various pulleys.

These decals are really impressive quality. They stick on really nicely, have super grip and a nice glossy finish. You can use them to make up your own signs, decorate your shop wall, trailer, or make up that car show easel/sign that you have been needing. Available only in left facing (traditional pose). Check out this video of our 2013 Open House event. See you next year! ...

NEW PRODUCT! This gauge tester can be used to test all gauges on any Ford vehicle from 1956 to 1983. We are privileged to be one of the first companies able to offer this new product that has long been needed by the classic car community. Now you can quickly determine if the gauges in your car are accurate with this gauge tester. You can verify the high medium and low reading for your gauges, and also shows that the Instrument Voltage Regulator is working. If you own a...

Exact Reproduction 289 Hi-Po Main Cap Set offered by Ford. They are cast and machined here in the USA from the original Ford blueprints. A set consists of caps numbered 1- 4 and requires the use of an original rear main cap to finish an engine. These caps are cast from the highest quality Nodular iron and machined for ease of fitting to any 289 block. The I.D. of the main bearing bore is .020 undersize and the side registers are .010 oversize on each side for proper adjustment before line...

Concourse Correct Timing Pointer for any 428 Super Cobra Jet Replaces Part Number C9OZ-6023-A.

Stamped Steel Pointer Mounts to Timing Chain Cover. Correct for 351C in most 1970-72 Mercury Cougar or Ford anything including Mustang. Can be used on any 1970-74 351C engine from Ford. Technically, 1972 California 351C cars and 1973 351C cars used a different timing pointer for what ever reason. Replaces Ford part D0AZ-6023-A.

Stamped Steel Pointer Mounts to Timing Chain Cover. Correct for 1968 Mercury Cougar and Ford Mustang with 390-2V, 390-4V, or 428CJ engines. Mounts with existing timing cover bolts. Reproductions are nice, but they are a copy of the 1969-70 timing pointer. Close, but no cigar. Replaces Ford part C8AZ-6023-A.

Stamped Steel Pointer Mounts to Timing Chain Cover. Correct for 1969-70 Mercury Cougar and Ford Mustang with 390-4V, or 428CJ engines. Mounts with existing timing cover bolts. Replaces Ford part C9AZ-6023-A.* Note 428 Super Cobra Jet uses a different pointer, see related.

Used stamped steel pointer mounts to timing chain cover. Correct for 1967 Mercury Cougar or Ford Mustang with S code 390 engine. Must be used with the 1967 style timing cover.

Fuel pump drive eccentric for Ford 351C engines 1970-74. Used eccentric from our wrecking yard. Includes inner and outer eccentrics, bolt, and washer. 2-1/2 inches in diameter. Ford part number D0AZ-6287-A.

Hex shaped Oil Pressure Sending Unit Extension. Mounts the oil pressure sensor away from the engine blockConstructed from steel with a durable zinc finish. 1/4" NPT male & female ends plus an additional 1/8" NPT female port for items requiring an auxiliary oil pressure source. Eliminates the need for a T-fitting adapter when adding an aftermarket gauge or sensor. Replaces Ford Part # : C2OZ-9B339 and D1UZ-9B339-DP

White reproduction fan for the Thermactor Smog Pump.

Bolt kit for installing the idler and adjusting pulley on any 1970-71 Ford Torino / Mercury Cyclone, or 1971 Mercury Cougar / Ford Mustang with 429/429CJ engines. 4 bolts 3/8-16x7/8 inch washer head bolts.  

Bolt kit for installing the idler and adjusting pulley on any 1968-69 Mercury Cougar / 1968-69 Ford Mustang or 1968-69 Ford / Mercury with small block 289 / 302 / 351W engines. 4 bolts 3/8-16x7/8 inch washer head bolts.  

Pair of bolts for installing the fuel pump on most V-8 engines. 289, 302, 351W, 390, 427-4V, and 428CJ. AMK bolts 3/8-16 x 1-1/2 inches. Sold as a pair, for installation of mechanical fuel pump into the timing covers. AMK F-519. 43530-S8.

Blue reproduction pressure relief valve plug, for the Thermactor Smog Pump. The correct smog pump should have a relief valve and this is the pressure setting plug that goes into the valve on those 1968-71 smog pumps. 1968 manual transmission cars all engines, Holley carburetor equipped cars 1968-71.

Used cover plate or thrust plate that retains the camshaft on the front of Ford V-8 engines such as 351C, 351M, 400, 429, 429CJ, and 460. 1970-76 Mercury Cougar or 1968-76 Ford anything. We have found a Ford number of C8SZ-6269-A. 

Used cover plate or thrust plate that retains the camshaft on the front of Ford FE big block V-8 engines such as 352, 360, 390, 410, 427, 428, and 428CJ. 1963-70 Mercury Cougar or Ford anything. We have found a Ford number of C3AZ-6269-A, 

WE CAN NOT SHIP THIS PRODUCT INTERNATIONALLY WITHOUT SHIPPING IT AS HAZARDOUS MATERIAL. THIS WILL INCUR HAZARDOUS MATERIAL CHARGES VIA UPS AND SOME COUNTRIES DO NOT ACCEPT IMPORTING THIS PRODUCT. New SEM aerosol flexable paint for the Mercury Cougar or Ford Mustang. This is a great match for the 1967, 1968 and 1969 dark blue interior color. SEM brand COLOR COAT is formulated to match, restore or change color on most vinyl surfaces, flexible and rigid plastics, carpet and velour. COLOR...

D0OA-3A14

Single 390GT cylinder head for a 1968 S code 390-4V engine. Sold as a core, needs thorough cleaning and rebuilding prior to use. Typically this cylinder head has 2.02 and 1.55 inch valves, and the chambers measure out at 71-74cc's. With stock pistons, these heads will net an approximate compression ration of 10.5:1. Basic cylinder head number is 6090. These are the GT exhaust manifolds with 14 drilled and tapped exhaust bolt holes. This cylinder head has 4 drilled and tapped, thermactor...

NOS Motorcraft condenser for point type distributors on any 1969-73 Mercury Cougar or Ford Mustang with V8 engines. Ford part number C9AF-12300-B and C9AZ-12300-A.

NOS New Old Stock oil dip stick tube for any 1968 Mercury Cougar or 1968-69 Ford or Mustang with 289 or 302 engines. Bare steel tube. Scott Drake makes a very good reproduction of this item for much less money. See related items.Ford part number C8AZ-6754-A.

NOS New Old Stock air conditioning fixed idler pulley for all 1967 Mercury Cougar and Ford and Mustang, all with 390 engines. Ford part number C7SZ-8678-B.

New Old Stock speaker for the 1967 - 68 Cougar or same year Torino. This is the speaker that fits inside the speaker pods situated behind the kick panels. These speakers are tested and in good shape with no tears on the cones. Good for the Cougar enthusiast who wants to keep their car as close to original as possible.Ford number C7OA-19A067. Sold individually. ...

These pads go between the rear quarter panel and quarter panel reflector on the 1968 Mercury Cougar only. Sold as a pair.  Replaces Ford part #: C8WY-13493.*Note - These were not installed on Ford Mustangs, but they could be installed since they use the same reflector after Feb 15, 1968.

These are the caps placed on the inside of the rear marker reflectors to protect your trunk's contents from damage. These Reproductions are grey. They were originally black with varying shades of grey. Sold in pairs, two pairs per car. Click on images to enlarge. Here is the Rear Marker Reflector without a cap. Here is the new cap on the marker. After you install the Rear Marker, screw the cap onto the Marker from the inside of the trunk. Below is a good used cap on the Marker. ...

Premium quality, exact fit plastic gasket set for both the driver and passenger side door handles. Also fits 66-71 Ford Fairlane and 70-71 Cyclone / Torino as well as several other Mercury, Ford Lincoln models. We are the exclusive retailers in the U.S. for this quality kit.

Authentic looking hard reproduction plastic Sport Mirror pad gasket. Correct for driver side Cougar Sport Mirrors 1971-73 and passenger side Torino / Cougar Sport Mirrors 1970-73. This is the best fitting gasket we've found so far. You may have to punch out the hole for the remote mirror cable. Replaces Ford #: C90Z-17724-B and D1WB-17C701-AB. Do you have questions about installing a passenger side mirror or using Riv-Nuts? Have more questions about installing a passenger side mirror or using...

Fan spacer, measuring 1-1/2 inches. Application includes 1970 Mercury Cougar and Ford Mustang with 351 engines and standard cooling. Reference number YA-21, cross reference to C8OE-8546-A spacer. This is a service replacement design spacer, which came out about 1970. Fits all the same.Ford Motorcraft part # D0AE-8546-B, Ford engineering # D0AZ-8546-B.

Shrink-on plastic sleeve that is found on the lower part of the collapsible steering columns. Used sleeves are often ripped and torn. Simply cut off your old sleeve and install this item to give your column a newer look and feel. Installation: Make sure that your column is clean. Lube the column and inside of the sleeve. Do not remove the crease on the plastic, you need it to help you put the sleeve on the tube. Push the sleeve on as far as you can. Gently tap the sleeve down on a table top...

1FBM-AD or D1MA-19A241 Factory AM/FM stereo radio for 1971 full sized Mercury cars such as Monterey and Marquis. "Mercury" is spelled out on the bezel or face plate. Unknown working condition.

C1AZ-3C590-A Our Ford Master Parts Catalog only goes back to 1965. However, there is a listing for this "Bushing kit - Power steering cylinder mounting rod end". 1965 Mustang V-8 and 1965 Fairlane. It should fit a variety of Ford and Mercury cars from 1961-1965.OEM Ford new in the box Autolite. Kit consists of : 2 - C1AA-3A344-A  Insulator, 1 - AJ-3652-A Spacer, 2 - C3AA-3A345-A Washers, 1 - 33925-S8 Nut, 1- 45218-S8 Nut. ...

GT 350 Holley 715 CFM center pivot bowl to bowl transfer tube. This is not for a regular Holley 4150. These tube ends are about 12-1/2 inches apart. Dual quads?

NOS low fuel sending unit for 1968 mid size Ford and Mercury excluding station wagon and Ranchero. Three prong plug for the low fuel wiring plug. We aren't sure if that 42 year old thermistor has a shelf life or not. Stamped C8OF-9275-A as shown. Ford MPC lists it for 1968, maybe 1969? we aren't entirely sure.Check out the video below on our new gauge tester: ...

Reproduction exterior mirror pad for the passenger side sport mirror on any 1969 Mercury Cyclone or Montego, or 1969 Torino, Ranchero, etc., all with factory sport mirrors. Nice quality plastic reproduction sport mirror pad. Marked C9OB-17C701-A.Replaces Ford part number C9OZ-17724-A.

This is a much cheaper version of the foil sound deadeners and underlays we sell. This particular insulation is basically bubble wrap with two layers of foil on both sides. Good for insulating headliners, floor pans, trunk areas, door panels, kick panels and just about anything else you might want to use it for. This insulation comes in a 48" X 72" roll. Just grab a pair of scissors and cut your shapes. You can use any adhesive you like (contact cement or weatherstrip adhesive,...

Locking pawl cable assembly for 67 - 69 TILT column T-Birds.

Gear Selector Plate for the T-Bird steering column shift machanism. 

Fits many 1970's passenger side sport mirrors (bullet shaped mirror not chrome). This is the Burco brand mirror you see advertised elsewhere for as much as $29 plus shipping. Comes with two sided adhesive tape. No returns and no phone orders on this part please. Measures: 2 3/4" X 4 5/16"Diagonally: 4.3125"Check out our videos on mirror replacement / repair below: ...

These came on most of the ford line up 1965 - 1967.  We will also trade straight across for the red mercury version or the black version with or with out the spinner as seen on our site.  Casting # C5MA-1141-B (on back).

Air conditioning fixed idler pulley for Ford or Mercury with the 289 engines. 1965, 1966, early 1967 Ford and Mercury full and midsized cars all with 289 engines and factory air conditioning. These are all sold with new bearings. If your pulley only needs a bearing, don't sweat it. Click this BEARING link, we've got what you need! Ford part # C5AZ-8678-D. ...

New coil spring compressing tool to compress the coil springs of the 1967-73 Mercury Cougar or 1965-73 Ford Mustang. This tool now comes with a bearing to make the job much easier. This spring compressor is a must for safely removing front coil springs. We also offer a 60 Day Loaner if you only need the tool for a short period of time. *NOTE* Not recommended for heavy duty coil springs like found on pickup trucks and full sized cars. ...

We will loan this coil spring compressor for 60 days, with a 100% refundable purchase price. This tool now comes with a bearing to make the job much easier. Only available to customers that purchase our front suspension rebuild kits. Tool must be returned in undamaged condition with no missing parts within the 60 day time period. Returns past 60 days are subject to a 25% restocking fee. Coil spring compressing tool, this is a must for safely removing front coil springs on any 1967-73...

New strip caulk for the Mercury Cougar or Ford Mustang. These units come in one foot strips and are used for sealing the front fenders to top of aprons and for sealing the fuel tank flange to the trunk floor. They are also used for sealing the floor drain plugs, gas filler necks, door panel water shields, plus many other components that are fastened to the body. This box contains 60 individual strips of black non-hardening caulk.

New spray silicone lubricant for the squeaky Mercury or Ford. This spray lubricant is great for door hinges, trunk hinges, hood hinges and basically anything else that needs to be lubricated. Easy to use and will definitely de-squeak your vehicle.

No more crust, white powdery battery terminals. Just spray this stuff on, and after a few minutes....simply wash off with water! Not only can you use this stuff on your car, you can use it on your ATV's, quads, dirt bikes and even your ride on lawnmower! A handy item to have laying around your garage. Of course, there's a little more messy, mostly free alternative which you can find the ingredients for online, but why bother? This is a simple, fairly cheap product to have.  

Here is another great product form Permatex. This decal and adhesive remover removes bumper and window stickers, tar, sap, bugs and other gooey substances. 

Permatex RTV gasket maker for the automatic transmission in your Mercury or Ford. Great stuff for sealing up that leaky transmission pan gasket!

New adhesive / epoxy applicator to apply our 3M window adhesive to the glass (or whatever else needs bonding) in your Mercury or Ford. This non-drip unit features an easy loading breech, a 1:1 mixing ratio and full cartridge support. We also offer a 60 day loaner if you only need this unit for a short time. ...

New red permanent strength thread locker for your project. This is a must have item if you are reassembling your pride and joy after restoration or just changing out parts. Often times, the vibrations from these antiques can vibrate loose the fasteners used to hold it together. If you use this, you can rest assured that your Merc or Ford will not fall apart from fasteners that have vibrated loose.

New RTV gasket maker for use on the differential of your Mercury or Ford. This gasket maker is specially formulated to withstand today's gear oils and prevent leakage.