All Available Parts - 1967 Ford Mustang

Used rectangular center duct tube for any 1967-68 Mercury Cougar or Ford Mustang with integral or factory air conditioning. Wire reinforced foam, will show some snags or signs of use. Will not have gaping holes. Was originally stapled to the center housing. Ford part number C7ZZ-19B680-B.

Original used female half of the factory air conditioning coupler for all 1967-73 liquid line or sight glass hoses. Brass construction, includes the plunger and spring. Also sold as a two piece kit which includes the male and female components. Replaces Ford part number C1SZ-19B596-A.

Vacuum tested working hot water valve for Mercury Cougars and Ford Mustangs equipped with factory A/C. This valve stops the flow of warm coolant when the A/C is on and has the original cast brass valve with bracket and vacuum pod. We are unable to guarantee that the water seal is good. Ford part # C7ZZ-18495-A, casting number on vacuum valve C7ZA-18C310-A.

Regardless of which V-8 engine, C7ZA-19972-E is the correct part number. This hose is approximately 20 inches long. Two different crimped ends, smooth and waffle may be the difference between Dearborn and San Jose or 1967 and 1968. Anyone know?The Ford MPC number is C7AZ-19972-A.

These beautiful reproductions replace rusty and corroded originals. 5/8" Replaces Ford Part #: C6AZ-18599-C

This is a blemished piece that we're offering at a discount. We received a shipment of these vents with some issues with the chrome finish. The flaws are visible in direct light but probably not noticeable when installed. Fit and function is the same as our premium units. See example photo for a closeup of the imperfect chrome finish.This reproduction A/C vent register with knobs is a perfect fit for your Mercury Cougar or Ford Mustang / Shelby. Includes all three control knobs. *NOTE* Mustang...

Used strap or support bracket for the foam air conditioning vent tube going to the passenger side A/C vent. The electrical assembly manual indicates that two of these strap brackets were installed above inside the dash above the glove box. Our findings from the wrecking yard show that zero or one may have been installed. We have found a single bracket, no doubles, if at all. This part will seldom be in stock, but is fairly easy to fabricate. Find some 1/2 inch wide thin steel and cut a piece...

This is a blemished piece that we're offering at a discount. We received a shipment of these vents with some issues with the chrome finish. The flaws are visible in direct light but probably not noticeable when installed. Fit and function is the same as our premium units. See example photo for a closeup of the imperfect chrome finish. This new reproduction is a spot-on replica of the 1967 passenger side AC vent! It differs from 1968 only in that 1968 used a break-away vent...

Vacuum switch not included. This control switch lever assembly only, for the vacuum and damper door consists of the two lever assembly for the vacuum and cable actuation of the A/C plenums damper doors on Mercury Cougar and Ford Mustang with integral A/C.Ford part # C7ZZ-19B888-A.

This new reproduction is a spot-on replica of the 1967 passenger side AC vent! It differs from 1968 only in that 1968 used a break-away vent that was very prone to failure. This is a fixed, one piece body and will not fall apart. This will be a direct fit to your 1967 and 1968 Ford Mustang with no modification needed. Dealer pricing available. *NOTE* Mustang used the shorter version of this vent than the Cougar did, otherwise they are visually and mechanically the same. Click on images to...

Original retainer for the passenger side A/C vent on Mercury Cougars and Ford Mustangs with equipped with factory A/C. Necessary for correctly installing the upper fastener of the vent.Ford part # C7ZA-19A950-A.

C7ZZ-15520-C Backup lamp switch that mounts to the factory 3 speed shifter linkage. 67 - 68 Mercury Cougar and Ford Mustang applications. Autolite or Motorcraft switch number SW-573. *Note - 3 speed switches are different than the manual 3 speed switches.

C7ZZ-15520-USED Backup lamp switch that mounts to the factory 4 speed shifter linkage. 67 - 68 Mercury Cougar and Ford Mustang applications. Autolite or Motorcraft switch number SW-561. Ford part number C7ZZ-15520-A. *Note - 4 speed switches are different than the 3 speed switches.

Normally we do not list Mustang specific parts, but since we are the distributor for these new reproductions, we need to have them accessible via our web site to all. This kit is the same as a Mercury Cougar set with the exception that the passenger side is shorter on the Mustang / Shelby than the Cougar. Top quality chrome finish and precision fit worthy of the most scrutinized restoration. Remember when we used to spend hundreds of dollars for "decent" used examples and then take a risk with...

Stud that the factory line workers used for locating the air conditioning pedestal bracket. Then backed up with a nut. Used on 289 / 302 / 351W / 390 / 428CJ pedestals from 1967 - 1973. We sell this item as reproduction, see related items.*Note - Excludes 351C and 429CJ.

OEM Ford stove type bolt for the securing the early style belt tensioner pulley. Used on Cougars and Mustangs produced before 1/3/1967. For use with C5AA-8A919-B Air conditioning belt tensioning pulley.

Used 14x5" stamped steel wheel for your Mercury Cougar or Ford Mustang. We save some of the better stock wheels and some have probably ridden in trunks most of their lives. These were offered in 1967, we believe that a 5-1/2 inch wheel was used starting in 1968-69. Have a bent or damaged wheel? Don't have a spare? Shipped bare. Various conditions and subject to availability. Used 'as is', wheel as found in the wilds of our wrecking yard.*Note - these wheels will not work with disc brakes...

Used 14x5-1/2" stock stamped steel wheel for your Mercury Cougar or Ford Mustang. We save some of the better stock wheels and some have probably ridden in trunks most of their lives. This 1967 specific wheel is slightly different than the more common 1968-69 stamped steel wheel. Limited to stock on hand.These were offered from 1967 through 1969. Have a bent or damaged wheel? Don't have a spare? Shipped bare. Various conditions and subject to availability. Used 'as is', wheel as found in the...

Used 14x6" stock stamped steel wheel for the Mercury Cougar or Ford Mustang. We save some of the better stock wheels you will ever find due to our mild climate and some have probably ridden in trunks most of their lives. This were offered in 1967 with S code 390-4V option. Hard to find the 1967 manufactured version, we generally have the 1968-70 wheels, but they have a different center section. Have a bent or damaged wheel? Don't have a spare? These wheels will fit over front disc brakes....

Unfortunately we are not presently offering this wheel as the supplier has been consistently sending us inferior product and poor customer service at an ever increasing price. Please consider our Legendary wheel line, here is a video that shows more: ...

Clean no nonsense look. 12MM Threads. Check out our video on rebuilding your shifter below:

Adapter plate for mounting the 3 or 4 speed shifter control assembly to the Top Loader transmission.Ford part # C7ZZ-7E046-A. Check out our video on rebuilding your shifter below: ...

This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of 50% of our web price for parts delivered in hand or by carrier to our Brooks, Oregon location. If you're not interested in store credit, just shoot us an email and we will let you know if it's is something we can pay cash for. We do not send cash for parts in advance but we often can compensate you within hours of receiving the...

C7ZZ-7515-D Manual transmission clutch fork - 3 and 4 speed, stick shift transmissions. Fork measures 12 inches long. Cougar 1967 through 2-15-1968. 390-4V engines only, XR7, XR7-G. Mustang 1967 through 2-15-1968. 390-4V only, GT. Mustang 1967. K code 289 HiPo 4 speed only. GT

Used speedometer cable from a 1967-68 Mercury Cougar or Ford Mustang with 4 speed transmission. These are assembly line used and would have had a Ford number of C7ZF-17260-A or C7ZZ-17260-J. Has captured hold down bracket at transmission. Cable has a rubber hose at the transmission end. These measure out about 76 inches long. Also has a metal sleeve about 10 inches from the speedometer cluster end, Cable clamp? Used condition, will have road grime, and maybe a couple of abrasions or small...

Nice reproduction clip for attaching the speedometer cable onto 3 and 4 speed 1967-70 Mercury Cougar and Ford Mustangs. Mounts to the firewall.

New internal speedometer gear fits 4 speed toploader transmissions. The largest number of 4 speed toploaders came stock with this gear. Replaces Ford Part #: C4DZ-17285-A.

D1TZ-7600-A New Old Stock service replacement clutch pilot bushing for all 1965-71 390/428/429 engines with manual transmissions. Will fit 1967-71 Mercury Cougar and Ford Mustang with 390-4V, 428CJ, 428SCJ, and 429CJ engines with 4 speed manual transmissions. Fits Fairlane, Cyclone, Torino, Ranchero also.

Good used setup as taken from a parts car. Will have good bushings in the hanger and show average wear is all the normal places. We will not send you worn out junk...

Ford small block engines and with a 3 or 4 speed manual transmission. Fits only the larger 164 tooth flywheel.

This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of 50% of our web price for parts delivered in hand or by carrier to our Brooks, Oregon location. If you're not interested in store credit, just shoot us an email and we will let you know if it's is something we can pay cash for. We do not send cash for parts in advance but we often can compensate you within hours of receiving the...

Manual transmissions, include both 3 and 4 speed Top Loader transmissions. Ford part number C6OZ-6392-B. The latest research shows that the casting number C60A-6394-B bellhousing may have been for 1966-68 Cougar, Mustang, Fairlanes and Comets with an 11 inch clutch disc.  Shipped bare, no hardware or clutch fork.

Grade A used inspection plate cover for all 390-4V and 428CJ engines with a manual transmissions, both 3 and 4 speeds. All years 1967 - 1970. Access cover to the flywheel and clutch. This is a real clean rust free cover but if you are wanting to save money, we have grade B's which will have a dent or creases for about half the price. Find the grade B here.Ford part number C3AZ-6366-A. ...

Stainless Steel Transmission Modulator Line for the 1967, 1968, 1969 and 1970 Mercury Cougar or Ford Mustang with the C6 transmission.

RAN-D or RAN-D1 Original equipment 3 speed top loader 3.03 transmission from a 1967 - 1968 Mercury Cougar with engine code C - 289-2V, or engine code A - 289-4V only. Could also have a casting number of RAN-D1. Ford master part number C5ZZ-7003-V.Percentages of Cougars equipped with a manual transmission by year1967 = 18.5%1968 = 13.2%1969 = 10.5%1970 = 7.8%1971 = 2.8%1972 = 1.5%1973 = 0.7%Total for 1967 to 1973 = 10.1% (Mustangs for the same time frame were 25.2%)Percentage of each...

RAT-N Original equipment 3 speed top loader 3.03 transmission from a 1967 Mercury Cougar with engine code S - 390-4V only. Ford master part number C7ZR-7003-A. *Note - RAT-N1 and RAT-N2 could be interchanged.Percentages of Cougars equipped with a manual transmission by year1967 = 18.5%1968 = 13.2%1969 = 10.5%1970 = 7.8%1971 = 2.8%1972 = 1.5%1973 = 0.7%Total for 1967 to 1973 = 10.1% (Mustangs for the same time frame were 25.2%)Percentage of each transmission;X = 46.8%W = 33.6%U = 9.5%1 = 7.2%5...

New manufactured flywheel for manual transmissions. Fits all 1967-68 Mercury Cougar and Ford Mustang with 289 engines with 3 or 4 speed manual transmissions. This flywheel has a 157 tooth ring gear. This flywheel will fit many other Ford small block V-8's with the 157 tooth gear.*Note - Most 1968 and newer Cougars came with 164 tooth flywheels, and they are not compatible.

Original dipstick tube. Application 1967 - 1969 Mercury Cougar or Ford Mustang with C6 automatic transmissions, code "U" on your door data plate. Ford master part number C8ZZ-7A228-A.

Used speedometer cable from a 1967-68 Mercury Cougar or Ford Mustang with C-6 automatic transmission. These are assembly line used and would have had a Ford number of C7ZZ-17260-C. Has captured hold down bracket at transmission. About 66-9/16 inches long. Used condition, will have road grime, and maybe a couple of abrasions or small cracks in the casing. The internal cable has been tested and is good. Tags generally are not present on these. Look at the related items, you may need a firewall...

This clips affixes the plastic speedometer gear to the cable. Some have found that this OEM original clip fits a little better than the reproduction we offer. *Trivia* Did you know the first Cougar cast for production in 1968 was this "Custom Cougar"? This fine example was offered up on ebay summer 2008 for a mere $6500.

Set of new bolts for attaching the floor shift bucket to the hump in the floor board, 1/4-20 bolts with washer head and 3/8 inch hex head. Sold as a set of 4 bolts. Fits all 1967 - 1973 Mercury Cougar and Ford Mustangs, and likely all of other floor shift Ford products from this time period. Check out our video on rebuilding your shifter below: ...

[No Description Provided]

Reproduction power steering hose retaining bracket and retainer. This is the bracket needed if you are routing the PS lines under the lower control arm instead of over as found on the 67 - 68 small block. Bracket and retainer will work on 1967-70 Mercury Cougar and Ford Mustang with small block V8 cars with the correct  power steering hoses. Replaces Ford part # C7ZZ-3C510-A, and C7ZZ-3C510-C.

Complete floor shift assembly for the 67 - 68 Cougar or Mustang. Included in this kit are the T-shifter assy, lever assy, housing and the shifter arm. Ford part numbers: C7ZZ-7210A C7ZZ-7A306B C7ZZ-7302A C7ZZ-7213M Check out our video on rebuilding your shifter below: ...

Ford called this part a 'sleeve'. Attaches to the lower shifter arm with a hitch pin. Has nice bushing, with correct nut, washer, and pin. The 1967/68 and 1969/73 versions are identical. The C1AA-7353-C sleeve has fine threads, the C9OZ-7353-A has course threads. Fits all 1967-73 Mercury Cougar and Ford Mustang, and we suspect many other Ford vehicles beginning in 1961. This fine thread version is hard to keep in stock, consider the 1969-73 course thread version as an alternative. Check out...

Attaches to the console shifter bezel on any 1967-68 Mercury Cougar or Ford Mustang. We occasionally have these available when we get broken console bezels. This surround or "U" plate was originally attached with heat to pin connectors. To reattach we suggest using glue. This U part attaches to the bottom of the console shifter bezel and shrouds the light. Check out our video on rebuilding your shifter below: ...

1967-69 Mercury Cougar and 1965 - 1969 Ford Mustang shifter handle for automatic transmissions. We find this smaller early style chromed shifter handle in lots of 1969 Cougars, we believe that there was a transition period before the C8OZ-7213-A was used. This is the base model shifter handle with both black buttons, and set screws. Ford part numbers C5ZZ-7213-F, C5ZZ-7C488-M, C5ZZ-7C488-D. Click on images to enlarge. Check out our video on rebuilding your shifter below: ...

Excellent high quality reproduction of the automatic transmission shifter bezel / indicator assembly for the 1967 and 1968 Mustang without console and 1968 Mercury Cougar XR7-G with XR7-G console. While not technically correct, this bezel can also be used on non-console Cougars (1967-1968) without modification. Ford part # C7ZZ-7D443-C. Check out our video on rebuilding your shifter below: ...

Stunning quality and far less likely to crack than the originals. The 67 version was actually a little different than 68 - 73 but you would have to look close to see the difference. Check out our video on rebuilding your shifter below: ...

Stunning quality and far less likely to crack than the originals. The 67 version was actually a little different than 68 - 73 but you would have to look close to see the difference. Check out our video on rebuilding your shifter below: ...

Stunning quality and far less likely to crack than the originals. The 67 version was actually a little different than 68 - 73 but you would have to look close to see the difference. Check out our video on rebuilding your shifter below: ...

Factory transmission support bracket for use on all 1967 - 1970 Cougars with 390-2V, 390-4V, 427-4V, 428 Cobra Jet engines and C6 automatic transmissions. Ford part number C7ZZ-6A023-B. This part weighs 3.5 pounds and when set on a level surface the height of the mounting hole on the driver side measures 2 3/4" on center and the passenger side is 3 1/2" on center. These "sometimes" will be stamped 390 on the inside.*NOTE* The key identifier on this C-6 unit that separates it from the...

Reproduction of the very hard to find crossmember for any 67 - 70 Cougar or Mustang with the 390 or 428 engine and the C6 transmission. Replaces Ford Part number C7ZZ-6A023-B

NOS power steering ram cylinder dated 6H25 or August 25, 1966. This one is date coded for a very early built 1967 Mercury Cougar or Ford Mustang, including Shelby GT350 and GT500. Bendix manufactured, shows a paint marking and gold cadmium? nut and band. Still has the plastic plugs and cardboard protection on the threaded shaft and drag link stud. Seals presumed to be good, but no guarantees.

This is a much higher quality bracket than other reproductions. Correct texture and fit. The bracket offered by most companies is just pot metal sprayed gray. Replaces Ford Part #: C7SZ-3A732-B or C7ZZ-3A732-B.

Tag marked HBA-BF or HBA-BF1 for use on 1967-68 Cougar and Mustang with power steering pumps originally installed on 289/302/390/427 and all 1968 428CJ engines. Various dates, and could be designated for either a Ford-Thompson (F) or TRW (W) power steering pump. For 1969 dated tags please see the related listing.*Please Note - Current inventory is exclusively 1967-68.

The originals hang at a slightly different angle than the reproductions. Comes as shown with original rubber insulator. New rubber available upon request. Seldom in stock, we suggest the 1969 small block version. It is very close to this one. Please see related item. This is the bracket needed if you are routing the PS lines under the lower control arm instead of over as found on the 67 - 68 small block. Replaces Ford part # C7ZZ-3C510-A, and C7ZZ-3C510-C.

Although this premium reproduction strut rod bushing kit appears very similar to the economy kit, they are in fact superior. The main difference being that the bushings are made from a higher quality rubber compound.Replaces Ford Part #: C6OZ-3A187-AR.

C5AZ-6221850-A Door lock knob for all 1967 Mercury Cougar and Ford Mustang. Additionally fits 1965 Ford full size cars such as Galaxie and Thunderbird. 1966-67 mid sized Ford Fairlane and Mercury Comet. Sold individually. Nice used condition.

Great option for international customers. Light weight, and all you need is a PC or laptop, and you can plug this drive in and access all the same information that you'd find in the full sized shop manual books.

Reproduction concours weave black rear interior panel windlace that helps hold the rear interior panels in place. It is also known as the pinch weld moulding. This one piece of windlace will fit on either the driver and passenger side and is about 2 total feet worth of windlace. You will have to trim this unit to fit and it should be about 20 inches when correctly trimmed. *NOTE* There are two types of this trim found in the 1967-68, the smooth or rough textured version like the one shown...

Four per car unless you have a 1968 decor or standard model that has the unique three hole armrest and then you will need six. Replaces Ford part # C7AZ-6224146. Check out our handy diagram below to find other '67-'68 door parts you may need. All the item numbers shown can be typed in to the search bar on our site. (Click image to view full size) ...

Early 1967 style glove box catch. Fits all 1967-68 Cougars and 1966-68 Mustangs.Replaces Ford part number C6OZ-6206064-A.

Reproduction Glove Box Catch for the 1967 and 1968 Mercury Cougar and Ford Mustang

This reproduction cigar / cigarette lighter socket is a good fit and is easy to install. This lighter socket also comes with the retainer. Replaces Ford part # C6ZZ-15055-B.

This is the stainless steel, single prong version fuel sending unit for 67 - 68 Cougars and Mustangs. Cougars equipped with the convenience control package, and the XR7's used a three prong version. These units are better than original being made from stainless. The function however is not as good as original but adequate and usually will work for years. If you have an original, often times it's just the float that needs replacing, so don't be quick to discard your original. *Note - This...

1967 390-4V Holley 4150 carburetor, automatic C6 transmission- California DSO 52 and 53. C70F-9510-D stamped on the carburetor air horn, Holley list #3796, 600 cfm. Core carburetor with proper numbers, we don't always have the factory Ford Autolite tag that was affixed to the top. S code 390-4V or 390GT engines and automatic transmissions. *Note - For use with California Thermactor smog equipped cars.

Used in-tank, fuel sending unit without the low fuel option. Tested and cleaned units for all 1967 Mercury Standard model Cougars and all Ford Mustangs with 16 gallon fuel tanks. This is an original 1967 fuel sending unit with one electrical prong. Ford casting number C7ZF-9275-C. This unit comes with a new 5/16 inch filter, brass float, and sending unit gasket. The only difference between this sending unit and the 1968 sending unit is the diameter of the pickup tube. The 1968 verison of this...

Reproduction fuel line that goes from the fuel pump to the carburetor made of OE steel for the Mercury Cougar or Ford Mustang equipped with the 390-4V engine. Fits all FE engines with Holley 4150, as long as they do not have the Carter "X" fuel pump. Carter X fuel pumps are not crimped together.

These steel tubes made to exact O.E.M. standards and specifications.

1967 289-4V Autolite 4300 carburetor, 3 or 4 speed manual transmission - California DSO 52 and 53. C7DF-C or AG stamped on the carburetor base, 1.00" venturi size 470 cfm. Application for 3 and 4 speed manual transmissions. Core, rebuildable carburetor with proper numbers. We don't always have the factory Ford Autolite tag that was affixed to the top. PCV spacer plates also available and required for stock air cleaner clearance on top of engine. A code 289-4V engines and manual...

1967 289-4V Autolite 4300 carburetor, Automatic C4 transmission- 49 states. C7DF-M stamped on the carburetor base, 1.00" venturi size and 470 cfm. Core carburetor with proper numbers, we don't always have the factory Ford Autolite tag that was affixed to the top. PCV spacer plates also available and required for stock air cleaner clearance on top of engine. A code 289-4V engines with automatic transmissions. *Note - Not for DSO 52 and DSO 53 California destined cars. ...

1967 390-4V Holley 4150 carburetor, 3 or 4 speed manual transmission - California DSO 52 and 53. C70F-9510-C stamped on the carburetor air horn, Holley list #3795, 600 cfm. Core carburetor with proper numbers, we don't always have the factory Ford Autolite tag that was affixed to the top. S code 390-4V and 390GT engines with manual transmissions. *Note - For use with California Thermactor smog equipped cars.

1967 289-2V Autolite 2100 carburetor, manual transmission - 49 states. C7DF-S stamped on the carburetor base, 1.02" venturi size 240 cfm. Application for 3 and 4 speed manual transmissions. Rebuildable core carburetor with proper numbers, we don't always have the factory Ford Autolite tag that was affixed to the top. PCV spacer plates also available and required for stock air cleaner clearance on top of engine. *Note - Not for DSO 52 or DSO 53 cars destined for California. *NOTE* Take a...

1967 289-2V carburetor, automatic C4 transmission - 49 states. C7DF-F stamped on the carburetor base 1.14" venturi size 300 cfm. Core carburetor with proper numbers, we don't always have the factory Ford Autolite tag that was affixed to the top. PCV spacer plates also available and required for stock air cleaner clearance on top of engine. C code 289-2V engines and automatic transmissions. *Note not for DSO 52 and DSO 53 California destined cars. *NOTE - Take a kid for a ride in a classic...

1967 289-2V Autolite 2100 carburetor, automatic C4 transmission - California DSO 52 and 53. C7DF-H stamped on the carburetor base, 1.02" venturi size 240 cfm. Core, rebuildable carburetor with proper numbers. We don't always have the factory Ford Autolite tag that was affixed to the top. PCV spacer plates also available and required for stock air cleaner clearance on top of engine. C code 289-2V engines and automatic transmissions. *Note-for use with California Thermactor smog equipped...

1967 289-2V Autolite 2100 carburetor, automatic C4 transmission - California DSO 52 and 53. C7DF-N stamped on the carburetor base, 1.02" venturi size 240 cfm. Core, rebuildable carburetor with proper numbers. We don't always have the factory Ford Autolite tag that was affixed to the top. PCV spacer plates also available and required for stock air cleaner clearance on top of engine. C code 289-2V engines and automatic transmissions. *Note-for use with California Thermactor smog equipped...

1967 289-2V Autolite 2100 carburetor, automatic C4 transmission - California DSO 52 and 53. C7DF-V stamped on the carburetor base, 1.14" venturi size 300 cfm. Core, rebuildable carburetor with proper numbers. We don't always have the factory Ford Autolite tag that was affixed to the top. PCV spacer plates also available and required for stock air cleaner clearance on top of engine. C code 289-2V engines and automatic transmissions. *Note-for use with California Thermactor smog equipped...

1967 289-2V autolite 2100 carburetor, automatic C4 transmission - 49 states. C7DF-F stamped on the carburetor base, 1.02" venturi size and 240 cfm. Core carburetor with proper numbers, we don't always have the factory Ford Autolite tag that was affixed to the top. PCV spacer plates also available and required for stock air cleaner clearance on top of engine. C code 289-2V engines and automatic transmissions. *Note - Not for DSO 52 and DSO 53 California destined cars. ...

1967 289-2V Autolite 2100 carburetor, manual transmission - California DSO 52 and 53. C7DF-G stamped on the carburetor base, 1.02" venturi size 240 cfm. Application for 3 and 4 speed manual transmissions. Core, rebuildable carburetor with proper numbers. We don't always have the factory Ford Autolite tag that was affixed to the top. PCV spacer plates also available and required for stock air cleaner clearance on top of engine. C code 289-2V engines and manual transmissions. *Note - For...

1967 289-2V Autolite 2100 carburetor, manual transmission - 49 states. C7DF-E stamped on the carburetor base, 1.02" venturi size 240 cfm. Application for 3 and 4 speed manual transmissions. Rebuildable core carburetor with proper numbers, we don't always have the factory Ford Autolite tag that was affixed to the top. PCV spacer plates also available and required for stock air cleaner clearance on top of engine. C code 289-2V engines and manual transmissions. *Note - Not for DSO 52 or DSO...

C7OE-9431-A Factory original cast iron exhaust manifold for driver side. 1967, 1968, and 1969 390/427 left side manifold remained unchanged for all three years. Includes 1968 X code 390-2V Premium fuel cars. Click on images to enlarge. ...

Generic hose kit that will fit the 289 or 302 for those who are not concerned about the CONCOURS look. Used on both the 20" and 24" wide radiators Replaces Ford Part #'s C4ZE-8260-A and C4ZE-8286-A. For some helpful tips on upgrading your Cougar (or Mustang) cooling system, check out our video: ...

C-4 transmission 90 degree brass fitting for the rear oil cooler line. New reproduction with jamb nut and "O"-ring. Fits 1967-68 Mercury Cougar and 1965-73 Ford Mustang where applicable.

Dated 7C20, March 20, 1967. Big block Ford water pump core, suitable for rebuilding. This version has a casting number of C6AE-8505-B. Found on many Ford 390 engines from 1966-67. These have casting dates, we list the dates when we have them in stock. Plan on sending it to a vendor that specializes in water pump rebuilding. In all likelihood, the rear cover, heater tube, and impeller will need replacing. See our other core water pump listings for other casting numbers. Two different...

Dated 7C17, March 19, 1967. Big block Ford water pump core, suitable for rebuilding. This version has a casting number of C6AE-8505-B. Found on many Ford 390 engines from 1966-67. These have casting dates, we list the dates when we have them in stock. Plan on sending it to a vendor that specializes in water pump rebuilding. In all likelihood, the rear cover, heater tube, and impeller will need replacing. See our other core water pump listings for other casting numbers. Two different...

Used FoMoCo 22 inch big block radiator marked C7ZE. This is for a 1967 Mercury Cougar or Ford Mustang with 390-4V and C-6 (automatic code U) transmission. This supplier with the Ford number stamped on the side strap is typically from Dearborn assembled cars. Used core radiator for recoring and restoration. This listing currently has an older replacement 4 tube core. The lower tank has minor damage to the area of the pet cock as shown. Typical Dearborn installed assembly line radiator.Replaces...

Used FoMoCo 22 inch big block radiator marked C7ZE. This is for a 1967 Mercury Cougar or Ford Mustang with 390-4V and manual transmission. Used core radiator for recoring and restoration. This listing currently has a lower tank with minor damage to the area of the hose outlet as shown. Typical Dearborn installed assembly line radiator.Replaces Ford part number C7ZE-8005

Used FoMoCo 20 inch small block radiator. This is for a 1967 Mercury Cougar or Ford Mustang with 289-2V, or 289-4V and automatic transmission (code w). Used core radiator for recoring and restoration. Typical Dearborn installed assembly line radiator. Factory installed automatic transmission radiators came with the fittings in the bottom tank for transmission cooling. Current listing is dated 7EC or 3rd week of May 1967. Late production date. Ford part number C7ZE-8005-S1 ...

C6OE-9428-A 390-4V factory original cast iron exhaust manifold for passenger side. Even though the photo shows a chamfer where an exhaust donut would go, the proper 1967 manifold would have been cast flush, and a butterfly spacer would have been used. The spacer had a flapper that partially blocked the pipe and allow heat to be dissipated upwards to the choke. Spacers not included. We suggest purchasing the later version of manifold that did not use the spacer. *Note, a spacer may be needed if...

Factory original cast iron exhaust manifold for the passenger/right side and is probably a mid-year change for 1967. For both S & X code 390 engines and W code 427 GT-E engines up until 2/15/1968. Butterfly spacer not included. Ford part # C7OE-9430-C.

This is the Water Pump Bolt Kit for 1967-68 Mercury Cougar and 1965-68 Ford Mustang with the 289 or 302 engines without air conditioning. This kit includes the 11 bolts needed to mount the water pump to the motor.  This kit comes with an instruction sheet, and shows the correct placement of the bolts.

Small block Ford water pump core, suitable for rebuilding. This version has a casting number of C6OE-A. Found on many Ford 289 engines from 1966-67. These do not have casting dates, and plan on sending it to a vendor that specializes in water pump rebuilding. In all likelihood, the rear cover, heater tubes, and impeller will need replacing. Occasionally they have the original non-HiPo cast iron impeller, but not always. See our other core water pump listings for other casting...

Dated 6M29, December 29, 1966. Big block Ford water pump core, suitable for rebuilding. This version has a casting number of C6AE-8505-B. Found on many Ford 390 engines from 1966-67. These have casting dates, we list the dates when we have them in stock. Plan on sending it to a vendor that specializes in water pump rebuilding. In all likelihood, the rear cover, heater tube, and impeller will need replacing. See our other core water pump listings for other casting numbers. Two...

Direct aluminum replacement for small block 1967 - 1969 cast iron pumps. Probably the last water pump you'll ever buy. Built to cool better and last longer than any other pump. Features state of the art high efficiency impeller with 16 veins and NASCAR roller type bearing. Race proven for reliability and performance. Includes Gasket. Several other websites state that there was a mid-year change in 1969 Cougar's with a 351W, but all the documentation we have and the cars we have on hand...

Good used crank correct for 1967 XR7 or standard models. No obvious blemishes, driver quality. The Ford part # is C5ZZ-6523342-C, casting number as found on the back reads C7ZB-6523348-A. *Customer Feedback* Don, Lin and staff; Just to let you gentlemen know that I have received the 1967 XR7 saddle tan door panels you sent and I am extremely happy with the condition and the service! It has been less than a week since I ordered them and they arrived via USPS, as per requested, with a very...

Fine scratches but great for the guy who wants original. The Reproduction does not have the II-DMI-6 lettering at the bottom like this original. You will have to carefully peel (roll back) the aluminum backing that is glued in place before gluing it in your mirror. If you use needle nose pliers and take your time it usually works fine. Note that the pictures of our 67-68 mirrors and lens can be deceiving. This is a tapered mirror, the narrow end faces upward on a Cougar, it is reversed when...

Refurbished pair of door lock cylinders and ignition cylinder for all double cut key Fords 1967-69. These are coded to the original key code, which was stamped onto one of the door lock cylinders. Includes two door lock cylinders, two Ford keys, and one ignition lock cylinder. Assembled from the best used locks. Replaces Ford part # C7AZ-6222050-A or C9AZ-6222050-A.

These two original hinges have been rebuilt with steel sleeves to retain the over-sized oil impregnated bushings. They feature hollow hinge pins which allows grease to fill the steel tube, lubricating the bushings under pressure from the inside-out. The threaded Zerk fittings are easily accessible from inside the car when the door is opened and are guaranteed to NEVER wear out or we will rebuild them for FREE! This offer has been in place for 20+ years by our rebuilder and they have never been...

Whenever you take on a door job, its always handy to have a few things available....a helper, a floor jack and a door hinge wrench. While a helper and floor jack might not always be available, a door hinge wrench is a valuable tool to have around when removing / setting a door. This Snap on obstruction wrench (google snap on part # S9608B) is specially curved to allow you to gain access to a few of those hard to reach bolts on your door hinges. We will loan this door hinge wrench for 60 days,...