All Available Parts - 1967 Ford Mustang

Reproduction pump end return hose for the 67 - 70 Cougar or Mustang. Cut to 2' length.

Used original lower power steering hose mounting bracket for 289 / 302 / 351 1967-69. Comes as shown with rubber insulator. This used version has the indexing tab which the reproduction does not. May come with new bolt and or rubber insulator.Replaces Ford part # C7DZ-3A609-A, C7DZ-3A610-A, C7ZZ-3C510-B, and C8ZZ-3C510-A.

Application could be for any 1967-69 Ford 289 / 302 /351W, but with only a single alternator belt. This is a copy of the Ford 7AA power steering pulley. This pulley mounted correctly on an OEM pump with factory brackets, will run on the second V-belt from the inside. The inner most fan belt runs the alternator. You would be using a single belt on the alternator. Correct application is for 1969 with 351W engines. 5-1/4" diameter and 3/8" sheave width.

C7OZ-3A697-A The most common power steering pump reservoir. Originally found on pumps with tag numbers: HBA-BF, HBA-BF1, and HBA-BR. These apply to 1967-69 Cougar and Mustang with power steering pumps originally installed on 289/302/390/427 and all 1968-1970 428CJ engines. Low pressure line nearly straight. *Note - Excludes 1969 302 & 351 engines. Our Grade B cans will always have some minor to moderate damage that is cosmetic. If you are capable of doing some minor body work they can made to...

Grade B Generic Ford power steering pump reservoir, has low pressure or return fitting point up. Check for hose clearance with your exhaust manifolds or headers on this reservoir. Fits 1967-69, and 1971-73 pumps with the small center hole for the pressure line. Most factory Ford pumps in 1970, had a larger hole, that was offset from center. Originally, these likely came from a full sized Ford car or pickup. Very common to find this style of reservoir on replacement power steering pumps....

Grade A Generic Ford power steering pump reservoir, has low pressure or return fitting point up. Check for hose clearance with your exhaust manifolds or headers on this reservoir. Fits 1967-69, and 1971-73 pumps with the small center hole for the pressure line. Most factory Ford pumps in 1970, had a larger hole, that was offset from center. Originally, these likely came from a full sized Ford car or pickup. Very common to find this style of reservoir on replacement power steering pumps. Our...

C7OZ-3A697-A The most common power steering pump reservoir. Originally found on pumps with tag numbers: HBA-BF, HBA-BF1, and HBA-BR. These apply to 1967-69 Cougar and Mustang with power steering pumps originally installed on 289/302/390/427 and all 1968-1970 428CJ engines. Low pressure line nearly straight. *Note - Excludes 1969 302 & 351 engines. Our Grade A cans are far and few between as often folks like to use a pry bar as leverage to over tighten their belt. These cans will usually have...

Tag marked HBA-BF or HBA-BF1 for use on 1967-68 Cougar and Mustang with power steering pumps originally installed on 289/302/390/427 and all 1968 428CJ engines. Various dates, and could be designated for either a Ford-Thompson (F) or TRW (W) power steering pump. For 1969 dated tags please see the related listing.*Please Note - Current inventory is exclusively 1967-68.

AMK strut rod hardware kit, course threaded bolts and nuts with cotter pins as shown.

Core power steering pump for the Mercury Cougar or Ford Mustang equipped with any V-8 engine. This unit is also for the 1970 Cougar or Mustang equipped with the 428CJ. These are bare pumps, stripped of pulleys, canisters, dip sticks, tags, and brackets. Suitable for core rebuilding. Typically these pumps would have been tagged with numbers which include: HBA-BF, HBA-BF1, HBA-BK, and HBA-BR. *Note - Excludes all 1970 cars with 351 or 302 engines. *NOTE* Core exchange not required. ...

This complete four piece kit is for any small block 289, 302, or 351 Windsor Cougar 1967, 1968 and 1969. 

Kit includes all repair parts necessary to refurbish leaking cylinder/piston rod seal area. Replaces Ford Part #: C1AZ-3A764-A.

This new reproduction power steering ram cylinder is good quality with almost no warranty claims. However, When you go to put your cotter pin in the castle nut you will often find it does not align perfectly which means you may have to drill it for a perfect fit. Keep in mind we will pay $30 in in-store credit for a clean original used ram cylinder so don't throw them away! RAM BOOT SOLD SEPARATELY. Replaces Ford Part #: C3DZ-3A540-A or C7ZZ-3A540-A. ...

This an original, rebuilt power steering slave / ram cylinder. It has not had a cosmetic restoration so it will show external dings, scrapes and general wear associated with a 50 year old part located on the bottom of a car. If you buy our reproduction ram do not throw away your core used ram as we often can give in store credit for the part. RAM DUST BOOT SOLD SEPARATELY.Replaces Ford Part #: C7ZZ-3A540-A.

Reproduction rubber boot for the drag link end of the power steering ram cylinder on most any 1967-70 Ford small and intermediate sized cars. Comes with band style crimp clamp like the originals. Keep in mind that this product is made from material that is thinner and softer than OEM.

Bolt kit for mounting power steering ram cylinder brackets to the frame rail on any 1967-70 Mercury Cougar or Ford Mustang. Kit includes: two short bolts with lock washers, long horizontal bolt, nut, and reinforcing washer. Quality AMK fastener kit.

Mounts onto the transmission. Fits all 1967 - 1968 8 Cylinder.

Kickdown return spring for 1967-68 Mercury Cougar with C4 transmissions, and 1967-69 Mercury Cougar with C6 transmissions. Same for 1965-69 Ford Mustang with C4 and 1967-69 with C6. Actual Ford part number is C5ZZ-7B146-A.

Quality part for your C-4 but will work on the C-6 67-68 transmission. Measures 10.2" long. Replaces Ford Part #: C6OZ-7A187-D.

C4 Automatic transmission kick down cable kit for all 1967-68 Mercury Cougar and 1966-68 Ford Mustangs. Kit includes kick down cable assembly, accelerator kick down lever, retracting spring, and related hardware.

Manual control shift linkage assembly for a floor shift C-4 transmission in any 1967-68 Mercury Cougar or Ford Mustang.  Check out our video on rebuilding your shifter below: ...

First generation Cougars 1967 and 1968, used a single bracket for C4 automatics and both 3 speed and 4 speed manual transmissions. This bracket also carried over to 1969 and 1970 with 351 or Boss 302 engines and either 3 or 4 speed manual transmissions. Ford part number C7ZZ-6A023-D. This part weighs 2.28 pounds and when set on a level surface the height of the mounting hole on the driver side measures 2 1/4" on center and the passenger side 2 3/4" on center.The reproduction Dynacorn part...

New crossmember to adapt the Tremec TKO manual transmission to the Mercury Cougar or Ford Mustang. This unit can also be used for the Ford AOD. 

Reproduction transmission support for 67 - 70 Cougars and Mustangs. We strongly recommend that you buy our used support, as these reproductions are inferior to the originals, and to be honest, they simply do not fit well.

Used transmission support for 67 - 70 Cougars and Mustangs. We strongly recommend that you buy this used support as compared to the reproductions. The repros we offer are inferior to the originals, and to be honest, they simply do not fit as well.

Dust and safety plate for all C4 (code W) automatic transmissions also known as the Cruis-o-Matic transmission. Inspection cover for torque converter and flexplate.

Steel inspection cover for all 1967 Cougar or Mustang with any of the FE engines 390, 427, or 428CJ and C6 automatic transmissions. Dust and inspection cover for the flexplate and torque converter. Usually will have a casting number of C6AP-7986-A stamped on it, also referred to as a Transmission C6 dust cover 390GT, 428GT500, 428CJ, 428SCJ.*Note - Some of these plates do not have the vent, or dimple at the bottom, like in the picture.Please keep in mind that this is a 40+ year old used item....

Reproduction dust and safety plate for all C4 (code W) automatic transmissions also known as the Cruis-o-Matic transmission. Inspection cover for torque converter and flexplate.NOTE - Although the C4 and the FMX inspection plate look similar visually, they are in fact different sizes with different bolt spacing.

Reproduction steel inspection cover for all 67 - 70 Cougars or Mustangs with 390, 427, or 428CJ engines with the C6 automatic transmissions. Dust and inspection cover for the flexplate and torque converter, also referred to as a Transmission C6 dust cover 390GT, 428GT500, 428CJ, 428SCJ.

Pair (2) Bolts for securing the inspection cover for any C-4 automatic transmission 1967-68 Mercury Cougar or 1965-70 Ford Mustang. Additionally also fits FMX transmissions 1969-73 Mercury Cougar.or Ford Mustang.

4 Bolts for securing the inspection cover for any C-6 automatic transmission 1967-70 Mercury Cougar or Ford Mustang.

If your automatic floor shifter has play in it left to right then this is the culprit. Easy to install, (more difficult if you have a 67-68 with center console) these are made from a wear resistant plastic that is better than original. Sold as a pair as two are required per car. This bushing was used in all Ford products equipped with a floor shift automatic from the 1965 Mustang to the late 70's Pinto. Replaces Ford Part # C5ZZ-7A133-A Check out our video on rebuilding your shifter below: ...

Exact reproduction for the 1967 - 1968. Perfect fit and finish. You may want to replace yours with this inexpensive unit just for the fresh new luster alone. Your plastic end buttons may have faded to gray but they were originally black like this one.Replaces Ford Part #: C5ZZ-7213-F.

Black plastic selector button for all 1968-72 Mercury Cougar and Ford Mustang with automatic transmission. This is for all cars with body type 65A, 63A, or 76A. This is for the base model shifter handle. Deluxe shifters were larger and had simulated leather wrapping. Ford part C5ZZ-7C488-M and C5ZZ-7C488-D. Your buttons may have faded to gray after many years. These black buttons are injection molded plastic and have steel wear plates just like the originals. Technically this is a copy of the...

Tired of picking your broken button off the floor? This inserts in the left hand side of your deluxe (colored keyed) shift handle. Quality part made in China, please consider our good used units at half the price! 67 is actually a little different in contour but this will fit fine. Replaces Ford #: C8OZ-7C488-A. Check out our video on rebuilding your shifter below: ...

Adjustable rod that connects the floor shifter to the big block C-6 automatic transmissions. C6 transmissions only, code "U" on your door data plate tag. FE big block 390/427/428CJ engines received the C-6 automatic transmissions. Shift rod approximately 17 inches long. Rod marked C7ZA-7326-A. Check out our video on rebuilding your shifter below: ...

Floor shifter access plug. 1967-73 Mercury Cougar and Ford Mustang, also fits floor shift 1971+ Mercury Comet and Ford Maverick. Ford Part number C7ZZ-7C147-A. Check out our video on rebuilding your shifter below: ...

This group of parts mounts to the top of the AT shifter arm and rides against the thumb activated button on your T shift handle. Its function is to lift the cable that runs through the chrome shifter stem to lock and unlock the shifter out of Park. The Ford technical name for this part is 'Roller - Shift Lever Lock'. We carefully inspect each part to make sure it is in perfect used condition. Ford part number C5ZZ-7D328-A. Check out our video on rebuilding your shifter below: ...

This gives the thumb release button in your T shaped shift handle its tension. If it is rusted then your button will not return back to its outer position easily. Fits 1967-73 Mercury Cougar and 1965-73 Ford Mustang. Technically this spring fits all Ford and Mercury floor shifters 1965-73. Ford part number C5ZZ-7C300-A. The MPC shows this spring to have a free length of 2-1/16 inches.

Automatic shifter cable with slot on the threaded end for all 1969-73 Mercury Cougar and Ford Mustangs. Will also work on 1967-68 but features a slot at bottom so as to remove or adjust easily. The 1967-68 version did not have this slot. Ford part number C9ZZ-7D246-A with the slotted threaded stud on the end. Also fits 1971+ Maverick & Comet with automatic floor shifters. Restoration Hint - We suggest purchasing this upgraded cable for use in 1967-68 shifter levers. Much easier to install, and...

Fit and and function wise this is the same as the 1968 - 1973 XR7 button and we suggest the quality reproduction we offer as a good replacement. However if you want 100% correctness then the 1967 button is different and there are no reproductions for this exact button. The 1967 button has a concave surface, while the 1968-73 button is convex. See the comparison photo below with the 67 deluxe button (Left) next to the 68-73 button (Right). This is a good used part with no pits or cracks. Ford...

This plastic linkage rod / arm connects the floor shifter to the indicator light inside your console that illuminates the PRND21 on your illuminated console panel. Used on all automatic consoles 1967 -1968 XR7 and standard. Ford part number C7ZZ-7E148-A. Check out our video on rebuilding your shifter below: ...

This is a correct reproduction C6 arm for a 1966 - 1969 FoMoCo pony car and midsize with a floor shift C-6 transmission. This also works on the 1970 as long as the lockout rod is removed. Midsize would be Fairlane Cyclone and the individual models associated with them like Ranchero, etc. Replaces Ford Part #: C6OZ-7A256-B Check out our video on rebuilding your shifter below: ...

This arm is attached to your automatic transmission floor shifter (see picture at left). Ford calls technical name for this part is 'Arm, Support'. These used parts will come with an intact bushing and nut. Correct for C-4 and C-6 transmissions. Ford part number C7ZZ-7302-A. ...

Adjustable rod that connects the floor shifter to the "Select-Shift-Merc-O-Matic" automatic transmission. C4 transmissions only, code "W" on your door data plate tag. Small block 289/302 engines received the C-4 automatic transmissions. Rod marked C7ZA-7326-B. Shift rod approximately 17-1/4 inches long. Check out our video on rebuilding your shifter below: ...

Black plastic selector button for all 1967 Mercury Cougar and 1965-67 Ford Mustang with automatic transmission. This is for all cars with body type 65A, 65C, 63A, or 76A. This is for the base model shifter handle. Deluxe shifters were larger and had simulated leather wrapping. Ford part C5ZZ-7C488-M. Check out our video on rebuilding your shifter below: ...

Black plastic dummy button for all 1967 Mercury Cougar and 1965-67 Ford Mustang with automatic transmission. This is for all cars with body type 65A, 65C, 63A, or 76A. This is the non-moving button on the right side of your shifter handle. This is for all cars with body type 65A, 63A, or 76A. This is for the base model shifter handle. Deluxe shifters were larger and had simulated leather wrapping. Ford part C5ZZ-7C488-D.

1968-72 (works on 1967) Mercury Cougar XR7 and Ford Mustang Deluxe shifter button for automatic transmissions. This is for all cars with body type 65B, 76B, and Grande. This is for the deluxe model shifter. These are used, and because of the low grade of chrome plating, these will show some form of light pitting.  handle, which is larger and has a faux leather covered handle in a variety of colors. Ford part number C8OZ-7C488-A. Check out our video on rebuilding your shifter below: ...

This shifter bucket is used on all 1967 - 1968 Mercury Cougars and Ford Mustang without an automatic center console. Bare bucket with good shift detentes and bushing hole that isn't worn out. Ford part number C7ZZ-7A306-B. Check out our video on rebuilding your shifter This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of 50% of our web price for parts delivered in hand or by carrier to...

Steel retaining plate. Ford part number C5ZZ-7B233-A. This plate is needed to fasten the shift indicator bezel on non-console cars. Fits 1967-68 Mercury Cougar and 1965-68 Ford Mustang, without console. Nice reproduction part, better value than used. You may also need a set of 4 attaching screws. Check out our video on rebuilding your shifter below: ...

Automatic shifter arm pawl - early version. Mounts inside the bottom of the shifter arm in the slot with the cable and spring. Fits original chromed shifter levers or arms 1967-70 Mercury Cougar, 1965-70 Ford Mustang, and 1965-66 Ford and Mercury full size cars with floor shift automatic transmissions. The early pawl has a key with a thickness of 0.100", the later (1970ish-73) with a thickness of 0.159". Check your shift lever for the size that you need, this early pawl has a Ford part number...

Locking nut that attaches the shift lever to the shifter arm and support inside the shifter buckets. We normally see the fine threaded nuts on the 1967-70 shifters. Please check your shift arm support for correct threads. Check out our video on rebuilding your shifter below: ...

Attaches to the console shifter bezel on any 1967-68 Mercury Cougar or Ford Mustang. We occasionally have these available when we get broken console bezels. This shifter dial was originally attached with heat to a pin connector. To reattach we suggest using glue. These look like it would be easy to detail the white letters for P R N D 2 1 with a careful hand. May have a chipped corner that is not seen when installed. Ford part # C7ZA-7A213A Check out our video on rebuilding your shifter below: ...

Restored chrome automatic shifter lever for any 1967-68 Mercury Cougar or Ford Mustang without consoles. The 1967-68 is similar to the 1969-73 shift lever, but has the additional chrome window section for holding the indicator light. These have been re-chromed, we sell these bare for those car owners that have pitted shifter levers. Ford part number C7ZZ-7210-A. This lever was also used on the 1968 XR7-G cars with unique consoles.*Note - Chromed lever only, sold without cable, pawl, handle,...

Restored chrome automatic shifter lever for any 1967-68 Mercury Cougar or Ford Mustang with consoles. This console lever is unique to console equipped cars, it has a tab with a hole in it for accepting the shift indicator indicator rod. We sell these bare for those car owners that have pitted shifter levers. Ford part number C7ZZ-7210-C. *Note - Chromed lever only, sold without cable, pawl, handle, etc. Check out our video on rebuilding your shifter below: ...

Complete chrome automatic shifter lever assembly for any 1967-68 Mercury Cougar or Ford Mustang without consoles. The 1967-68 is similar to the 1969-73 shift lever, but has the additional chrome window section for holding the indicator light. Good used part no heavy pitting on the chrome, we sell these levers with installed cable, pawl, spring, and gear release assembly. Ford part number for the lever is C7ZZ-7210-A. This lever was also used on the 1968 XR7-G cars with unique consoles. *Note -...

Allen head set screw for all stock Ford automatic shifter handles on any 1967-73 Mercury Cougar or Ford including Mustang. Uses the same 3/32 inch allen wrench for attaching as the originals. Most handles take two of these set screws, one on the dummy button, and one to attach to the top of the shifter lever. The 1973 all chrome shift handle only uses one of these set screws. Original Ford part number 374985-S. Check out our video on rebuilding your shifter below: ...

Reproduction shifter assembly for the Mercury Cougar or Ford Mustang equipped with the automatic transmission, but without a center console. Check out our video on rebuilding your shifter below: ...

Replacement rubber bushing for repairing any automatic shift arms on any 1967-73 Mercury Cougar or Ford Mustang, and most Fords with automatic floor shift levers. Fits arms with 3/4 inch lower holes for attaching transmission shift rods. Replaces Ford part number C7ZZ-7343 Check out our video on rebuilding your shifter below: ...

Complete console shift assembly for the 67 - 68 Cougar or Mustang. Included in this kit are the T-shifter assy, lever assy, housing and the shifter arm. Ford part numbers: C7ZZ-7210C C7ZZ-7A306A C7ZZ-7302A C7ZZ-7213M Check out our video on rebuilding your shifter below: ...

Power Steering hose bracket insulator for both the small and big block brackets for the 1967 - 1970 Mercury Cougar and Ford Mustang. Replaces Ford part #: C7ZZ-3A609-A or C7ZZ-3609. Customer feedback found at mercurycougar.net: Boy service is just not the same as the "good old"? days. I ordered a half a trunk load of parts and pieces from West Coast Classic Cougar and about 2 hours later got a phone call informing me that the order was picked and shipped. What are things coming to? Where is...

Fit and and function wise this is the same as the 1968 - 1973 XR7 button. However if you want 100% correctness then the 1967 button is different and there are no reproductions for this exact button. The 1967 button has a concave surface, while the 1968-73 button is convex. See the comparison photo below with the 67 deluxe button (Left) next to the 68-73 button (Right). This is a replated part with no pits or cracks. Ford part number C7ZZ-7C488-B. $20 refundable core charge will be added. Click...

Not a very good color match for Cougar owners, but will work well with blue interiors.Stunning quality and far less likely to crack than the originals. The 67 version was actually a little different than 68 - 73 but you would have to look close to see the difference. Check out our video on rebuilding your shifter below: ...

Used C6 arm for a 1966 - 1969 FoMoCo pony car and midsize with a floor shift C-6 transmission. This also works on the 1970 as long as the lockout rod is removed. Midsize would be Fairlane Cyclone and the individual models associated with them like Ranchero, etc. Replaces Ford Part #: C6OZ-7A256-B Check out our video on rebuilding your shifter below: ...

This plastic linkage rod / arm connects the floor shifter to the indicator light inside your console that illuminates the PRND21 on your illuminated console panel. Used on all automatic consoles 1967 -1968 XR7 and standard. Ford part number C7ZZ-7E148-A. Check out our video on rebuilding your shifter below: ...

Reproduction adjustable rod that connects the floor shifter to the big block C-6 automatic transmissions. C6 transmissions only, code "U" on your door data plate tag. FE big block 390/427/428CJ engines received the C-6 automatic transmissions.Includes pin and nut. Shift rod approximately 18 inches long. Replaces Ford part number marked C7ZA-7326-A. Check out our video on rebuilding your shifter below: ...

Reproduction engine spacer plate and inspection cover for the 67 - 68 Cougar, Ford, or Mustang equipped with the 289 or 302 V8 with C-4 transmission (code W). 6 bolt bell housing. See related items for inspection cover plate by itself, or bell housing bolts, or inspection cover bolts. Replaces Ford part number C7AZ-7A008-E.

Formed metal clip that holds the gear end into any transmission. Automatic codes W - C4, X - FMX, U - C6, 1 - 3 speed manual, 5 or 6 - 4 speed manual.

Unlike previous reproductions this has the correct grommet that passes through the firewall. 68 inches long replacement speedometer cable. New picture coming soon. Fits both C-4 and C-6 automatic transmissions for 1967-68 Mercury Cougar and Ford Mustang.Replaces Ford Part #: C7ZZ-17260-A.

Made out of Nylon. Please confirm teeth count and direction of teeth. Color codes do not guarantee direct replacement. 4 speed Toploaders have reversed tooth direction. Click here to use our Speedometer Gear Calculator. Available in 16, 17, 18, 19, 20, 21, and 23 tooth*. Replaces Ford Part: C0DZ-17271-A, C0DZ-17271-B, C0DZ-17271-C, C0DZ-17271-D, C0DD-17271-A, C1DZ-17271-A * - 23 tooth gears are not a Ford part and only have a life expectancy of 25,000 miles. They also have been reported to...

Made out of Nylon. Please confirm teeth count and direction of teeth. Color codes do not guarantee direct replacement. 4 speed Toploaders have reversed tooth direction. Click here to use our Speedometer Gear Calculator. Available in 16, 17, 18, 19, 20, 21, and 23 tooth*. Replaces Ford Part: C0DZ-17271-A, C0DZ-17271-B, C0DZ-17271-C, C0DZ-17271-D, C0DD-17271-A, C1DZ-17271-A * - 23 tooth gears are not a Ford part and only have a life expectancy of 25,000 miles. They also have been reported to...

Made out of Nylon. Please confirm teeth count and direction of teeth. Color codes do not guarantee direct replacement. 4 speed Toploaders have reversed tooth direction. Click here to use our Speedometer Gear Calculator. Available in 16, 17, 18, 19, 20, 21, and 23 tooth*. Replaces Ford Part: C0DZ-17271-A, C0DZ-17271-B, C0DZ-17271-C, C0DZ-17271-D, C0DD-17271-A, C1DZ-17271-A * - 23 tooth gears are not a Ford part and only have a life expectancy of 25,000 miles. They also have been reported to...

Made out of Nylon. Please confirm teeth count and direction of teeth. Color codes do not guarantee direct replacement. 4 speed Toploaders have reversed tooth direction. Click here to use our Speedometer Gear Calculator. Available in 16, 17, 18, 19, 20, 21, and 23 tooth*. Replaces Ford Part: C0DZ-17271-A, C0DZ-17271-B, C0DZ-17271-C, C0DZ-17271-D, C0DD-17271-A, C1DZ-17271-A * - 23 tooth gears are not a Ford part and only have a life expectancy of 25,000 miles. They also have been reported to...

Made out of Nylon. Please confirm teeth count and direction of teeth. Color codes do not guarantee direct replacement. 4 speed Toploaders have reversed tooth direction. Click here to use our Speedometer Gear Calculator. Available in 16, 17, 18, 19, 20, 21, and 23 tooth*. Replaces Ford Part: C0DZ-17271-A, C0DZ-17271-B, C0DZ-17271-C, C0DZ-17271-D, C0DD-17271-A, C1DZ-17271-A * - 23 tooth gears are not a Ford part and only have a life expectancy of 25,000 miles. They also have been reported to...

Made out of Nylon. Please confirm teeth count and direction of teeth. Color codes do not guarantee direct replacement. 4 speed Toploaders have reversed tooth direction. Click here to use our Speedometer Gear Calculator. Available in 16, 17, 18, 19, 20, 21, and 23 tooth*. Replaces Ford Part: C0DZ-17271-A, C0DZ-17271-B, C0DZ-17271-C, C0DZ-17271-D, C0DD-17271-A, C1DZ-17271-A * - 23 tooth gears are not a Ford part and only have a life expectancy of 25,000 miles. They also have been reported to...

Used clip with bolt for attaching the speedometer cable to the transmission of the Mercury Cougar or Ford Mustang. This unit holds the gear end into both automatic and manual transmissions. Automatic codes W - C4, X - FMX, U - C6, 1 - 3 speed manual, 5 or 6 - 4 speed manual.

Used speedometer cable from a 1967 Mercury Cougar or Ford Mustang with C4 transmission. These are assembly line used and would have had a Ford number of C7ZF-17260-D or C7ZZ-17260-D. Has captured hold down bracket at transmission. 1967 cables have a rubber sleave about 3 inches long at the transmission end. These measure out about 63-1/16 inches long. Used condition, will have road grime, and maybe a couple of abrasions or small cracks in the casing. The internal cable has been tested and is...

Reproduction transmission cooling lines for the Mercury Cougar or Ford Mustang equipped with the C-4 automatic transmission. These lines are sold in pairs.

Small Block V8 with C4 Vacuum line for 1967 - 1969 Mercury Cougar / Ford Mustang

Small Block V8 with C4 Vacuum line for 1967 - 1969 Mercury Cougar / Ford Mustang

An Exact copy. Natural gray paint for correct look and rust prevention.

Flawless chrome plating, available in stock depth only. Includes drain plug.

Flawless chrome plating, available in stock depth only. Includes drain plug.

Replacement transmission pan filter and pan gasket kit. For the C-6 (U Code) transmission. Replaces Ford Part Number: C7ZZ-7A098

Fits C4 transmissions. Painted glossy black. O-ring included Replaces Ford part # C6OZ-7A228-B. Application 1967 - 1968 Mercury Cougars with 289/302 engines and automatic (C4) transmissions, code "W" on your door data plate. 1966 - 1968 Ford Mustangs with 28/302 engines and automatic transmissions, code "W" on your door data plate.

An exact copy with a beautiful chrome mirror finish.

Original dipstick or in Ford speak "Indicator - Oil Level" for C4 automatic transmissions. Application for 1967-68 Mercury Cougar 1966-70 Ford Mustang with 289/302 engines and C4 automatic transmissions, code "W" on your door data plate.Ford part # C6OZ-7A020-B.

Fits C4 transmissions. Chrome finish. O-ring included Replaces Ford part # C6OZ-7A228-B. Application 1967 - 1968 Mercury Cougars with 289/302 engines and automatic (C4) transmissions, code "W" on your door data plate. 1966 - 1968 Ford Mustangs with 28/302 engines and automatic transmissions, code "W" on your door data plate.

An exact copy with a beautiful chrome mirror finish. 1 inch deeper than stock.

An Exact copy. Natural gray paint for correct look and rust prevention. 1 inch deeper than stock.

New manufactured transmission oil pan for the Ford C6 transmission as found on 1967-73 Cougar and Mustangs, big block and small block engines. Very high quality heavy gauge steel.Replaces Ford part number C6AZ-7A194-A.

Reproduction transmission dipstick tube for 67 - 70 Cougars or Mustangs equipped with the C4 automatic transmission.Replaces Ford Part number C6AZ-7A020-B

Reproduction transmission cooling lines made of OE steel for the Mercury Cougar or Ford Mustang equipped with a V-8 engine and the C-6 automatic transmission. These lines are sold in pairs.

Reproduction transmission cooling lines made of OE steel for the Mercury Cougar or Ford Mustang produced from 1967 through early 1968 that came equipped with the C-6 automatic transmission and 390 engine. These lines are also available in stainless steel and are sold in pairs.

New manufactured transmission yoke for a T-5 5 speed transmission.

New manufactured transmission slip yoke for either C-4 automatic transmission or small block manual 3 or 4 speed manual transmissions. Ford 1965-1973. 28 splines and 1-1/16" U-joint caps.

1967-70 Cougars with any FE engine (390-2V, 390-4V, 427 GT-E, 428CJ, or 428SCJ) and with C6 automatic transmission or manual transmissions.  Ford part #: C3AZ-7007-D.

1967 1968 Cougar with 289 engines and a 3 or 4 speed manual transmissions. Will only work with 157 tooth bellhousings and flywheels. Replaces Ford part number C5DZ-7007-A.

Reproduction engine spacer plate for the 67 - 68 Cougar or Mustang equipped with the 289 V8 with manual transmissions (6 bolt only).Replaces Ford part number C5DZ-7007-A.

Grade B used inspection plate cover for all 390-4V and 428CJ engines with a manual transmissions, both 3 and 4 speeds. All years 1967 - 1970. Access cover to the flywheel and clutch. This cover will have some rust and a dent or creases. Find the Grade A cover here.