All Available Parts - 1970 Ford Mustang

Trico brand wiper blade refills for 1969-70 Mercury Cougar or Ford Mustang with original wiper arms

Original stainless wiper blade assembly, pulled right off of a 1969 Mercury Cougar. ANCO brand original marked Made in USA O. E. by ANCO. Sold individually, two per car, 16" rubber wiper blade not included. These are production line installed wiper holders, we very seldom have them in stock. Originals didn't easily allow the replacement of the rubber blades. Notice the metal flap keeper on each end for capturing the rubber wiper blade?

Used vented fuel, or gas cap as installed on 1967-69 Mercury Cougar and 1970 cars without California emissions. Also fits 1969-70 Shelby Mustang. In 1970 California required a non-vented fuel cap. This version does have a check valve, one way vented. This is probably a service replacement fuel cap. Typically, OEM factory caps only said "VENTED", see our related item for that specific gas cap.We stock these in limited quantities, and will have an intact paper gasket. "ANTI SURGE"...

This used fuel / gas tank shows small dents on the underside but the top side is perfect and the inside has no corrosion. This tank would be good for "splitting" and combining this good used upper half with a reproduction lower half. We recommend converting to the non-evaporative 1970, 49 state tank, unless concours is desired. Conversion requires 1970, 49 state style filler neck and filler hose. We prefer that you come to pick this one up as we cannot ship anything that smells like...

Quality U.S.A. made hose with concours repeating GAS markings. Also include OEM mounting hardware. Replaces Ford Part #: C7ZZ-9327-A. Check out our video on replacing the fuel system on a '68 Cougar! ...

Factory original Carter fuel pump that was taken from a low mile 427 GTE in 1997. The "X" pump was used only on the Boss 302, 427, 428 and 429 Cobra Jet, and Super Cobra Jet.

Used Carter fuel pump lever. From Carter made fuel pump as installed on Ford 352, 390, 410, 427, 428CJ FE engines. Many of the Carter "X" fuel pumps with screw together rebuildable pumps often times have Ford small block levers. Housings are he same. Levers are removable, see youtube for the rebuilding and assembly procedure.

Nice rebuildable core of the Carter X 4441S fuel pump for all 1968-70 428 Cobra Jet engines. Has "X" casting, 4441S stamped, dated 10B9A, February 10, 1969. Kits available for rebuilding. 

Reproduction fuel pump for all 1967-70 Mercury Cougars and Ford Mustangs equipped with the 289, 302 or 351W engines. Be aware that this pump has a 3/8 inch fitting for the fuel line.

These Spark Plug Wire Separators are made of high-quality ABS plastic. Constructed to hold both standard 7mm and 8mm high-performance spark plug wires. Fits directly on valve cover clip. Available in blue, red and OE black.

If you find that this tube has too small of fittings for your OEM 4150 / 4160 Holley carburetor than what has happened is that someone has replaced your transfer tube and fittings with one of the after-market kits available at speed shops. This is the ONLY correct transfer tube for a Cougar equipped with a Holley from 1967 - 1970.  Ford part # C9AZ-9H576-A.

Used Under-dash Wiring Harness Plastic Cover / Clip for the 1969 and 1970 Mercury Cougar or Ford Mustang

Used plastic clip for the Mercury Cougar or Ford Mustang.

Delicate clip that attaches to a nail-head stud attached to the firewall. Very functional and visible, rather hard to find in unbroken condition.

Reproduction intermediate pipe exhaust bracket for the 67 - 70 Cougar or Mustang. Used on big block vehicles equipped with the transverse muffler. Attaches to the resonator exhaust hangers just before the muffler pipe rises above the rear end. Sold individually, 2 required per car.

Used intermediate pipe exhaust bracket for the 67 - 70 Cougar or Mustang. Used on big block vehicles equipped with the transverse muffler. Attaches to the resonator exhaust hangers just before the muffler pipe rises above the rear end. Sold individually, 2 required per car.

New gaskets for installing your intake manifold. This is the Felpro branded gasket. Fits 1969-70  Boss 302 Ford engines. 1969-70 Mercury Cougar Eliminator and Ford Mustang with G code 302HO engines. *Note - Excludes 289 / 302 / 351C / 351W engines. 

New gaskets for installing your intake manifold. This is the Felpro branded gasket. Fits all 1970-73 Ford 351C engines with 2 barrel intake manifolds 1969-70 Mercury Cougar and Ford Mustang with 351C-2V engines. This gasket set includes a metal pan gasket.Any doubts? 351 Windsor engines have 6 bolts holding the valve covers in place. 351 Cleveland engines have 8 bolts holding down the valve covers.*Note - Excludes 351W engines. *Note - Excludes 351C-4V Cleveland engines. ...

C9ZE-6A360-A Very unique part and a component to the 'drag pack' option on the 428SCJ engines. This is an additional counter weight used on conjunction with the SCJ crankshaft, SCJ crankshaft balancer. Ford part number C9ZZ-6359-A.

New gaskets for installing your intake manifold. This is the Felpro branded gasket. Fits 1964-73 small block Ford engines with size 260/289/302 cubic inches. C code 289-2V, A code 289-4V, F code 302-2V, and J code 302-4V.*Note - Excludes 1969-70 Boss 302 engines.

New gaskets for installing your intake manifold. This is the Felpro branded gasket. Fits 1969-73 small block Ford engines with size 351 cubic inches, Windsor engine only. 1969-70 Mercury Cougar and Ford Mustang with 351W engines.Any doubts? 351 windsor engines have 6 bolts holding the valve covers in place. 351 Cleveland engines have 8 bolts holding down the valve covers.*Note - Excludes 289/302 engines. *Note - Excludes 351C or 351 Cleveland engines.

Ford casting number D0ZE-6316-A Includes all 1970 G code Boss 302 engines. Ford master part number D0ZZ-6316-A. Has the timing marks on rim. This good quality used balancer is a good option for those wanting to keep a 100% original looking appearance on a concours car that does not get driven or see high RPM's. If you have a rebuildable core D0ZE-6316-A balancer to trade, we can offer a substantial discount.*Note - Excludes 1969 Boss 302 and all non-Boss 302 engines.

Ford casting number C8AE-6316-C Includes all 1969-70 Q or R code 428SCJ engines or those cars with the drag pak option. The C8AE-6316-C harmonic balancer is identified by the 3 bolt holes for attaching the crankshaft pulley. Outside diameter is approximately 7-1/2 inches. Ford part number C8AZ-6316-C. Has the timing marks on rim. The rubber in this used balancer will be the original and will not be showing cracks or signs of having shifted. This good quality used balancer is a good option for...

D0ZE-9425-E Cast aluminum intake manifold used on all 1970 G code Boss 302 engines in a Mercury Cougar or Ford Mustang. Stock 4 barrel intake manifold. Take off manifold with correct casting number of D0ZE-9425-E . Intake shipped bare, less carburetor studs, heater tube, vacuum fittings, and water neck where applicable. Ford master part number C9ZZ-9424-D or -E.

Reproduction dual port vacuum advance for most all 1968-70 Ford V-8 engines. Very close replica of the factory installed vacuum advance. This version has one pressed in brass fittings for vacuum hose, and one threaded port with added vacuum fitting as shown. This working vacuum advance will need to have your threaded plug installed in the port end. OEM Ford units had gold colored bands instead of this silver band as shown. This unit very closely matches the 1968-69 vacuum advance, the later...

Concours vacuum hose kit with colored stripes. Multiple pieces, connects carburetor, distributor, and thermal vacuum switch on the water neck. Fits all 1968-69 Mercury Cougar or Ford Mustang with S or X code engines. Additionally fits 1968-70 428 Cobra Jet engines. This kit is for the distributor vacuum advance units with single nipple connections. Often times it is the ones with manual transmissions, but not always.

Original distributor vacuum advance control valve, also called a ported vacuum switch (PVS) valve, that was installed on all Ford models including Mercury Cougar, Ford Mustang, and Torino starting in 1967. This is a used original pot metal and brass part. It has the FORD oval logo and part number C8AE-A casting.This casting number is correct for all 1968 1969 and 1970 Fords and Mercury. It was used on all engine options including 302 351C 351W 429 and 429CJ models. Because of the heavy demand...

Reproduction hold down clamp rivet for the 67 - 73 Cougar or Mustang. This rivet holds the clip / clamp onto the distributor. Sold individually, 2 per car.

New rubber "O" ring for Ford V-8 distributors from 289/302/351W/351C/429 engines.

Pertronix brand 7mm spark plug wires. These are performance oriented wires compared to the concours spark plug wires. For any 1967-73 Mercury Cougar and Ford with 289 or 302 engines. Black wires and boots, quality spark plug wires taylor made for the small block Ford engines. Recommended by Pertronix for use with the Flame Thrower coils.

Pertronix brand 7mm spark plug wires. These are performance oriented wires compared to the concours spark plug wires. For any 1967-73 Mercury Cougar and Ford with 351 - 390- 428 - 429 engines. Black wires and boots, quality spark plug wires taylor made for 351 engines and the big block Ford engines. Recommended by Pertronix for use with the Flame Thrower coils.

Powerful oil filled coil that generates 40,000 volts, designed to work with the either of our Pertronix Ignitors. Sold in black or chrome. *Note - This coil is not necessarily needed with the Pertronix Ignitors, the stock Ford coil works fine for most applications.

NOTE: WE SUGGEST LOCAL PICK UP ONLY FOR CORE ENGINE BLOCKS BECAUSE WE CANNOT GUARANTEE BLOCKS WILL NOT HAVE CRACKS INTERNALLY. Used standard bore 4.00" Ford 351C 1970 engine block. Will be used, dirty, have measurable taper, and will have a ridge. Good for rebuild. Bare block, Will have D0AE casting. 1970 Cleveland blocks have a unique "D" shaped raised casting mark. When we have them in stock we will post the casting date or dates. Heavy, will require either local pickup or freight...

NOTE: WE SUGGEST LOCAL PICK UP ONLY FOR CORE ENGINE BLOCKS BECAUSE WE CANNOT GUARANTEE BLOCKS WILL NOT HAVE CRACKS INTERNALLY.Used standard bore 4.00" Ford 351W engine block. Will be used, dirty, have measurable taper, and will have a ridge. Good for rebuild. Bare block, will have C9OE-6015 casting. Dated 9J23, September 23, 1969. Picture may show item with damaged oil pan and crank shaft and pistons. When we have them in stock we will post the casting date or dates. Heavy, will require...

NOTE: WE SUGGEST LOCAL PICK UP ONLY FOR CORE ENGINE BLOCKS BECAUSE WE CANNOT GUARANTEE BLOCKS WILL NOT HAVE CRACKS INTERNALLY. Long block, factory H code 351-2V V-8 engine. 351 Cleveland engine rated at 250 Hp with 9.5:1 compression ratio in 1970. Likely 0.030" bored motor that may or may not have been in running condition when pulled. Guaranteed to be rebuildable. Complete engine less carburetor, distributor, exhaust manifolds, fan, accessories, pulleys, and flex plate. Intake manifold and...

Used Distributor / 351C-2V / for the 1970 Mercury Cougar / 1970 Ford Mustang Ford part number D0AF-12127-V  

Used distributor for the Mercury Cougar or Ford Mustang that is equipped with the 351 Cleveland 2V engine.

Used core distributor for 1970 Mercury Cougar and Ford Mustang with M code 351-4V and automatic transmission. Core distributors will have correct stamping of D0OF-Z, 351 Cleveland Engine. Original Ford part number D0OF-12127-Z.

Used core distributor for 1970 Mercury Cougar and Ford Mustang with M code 351C-4V and either 3 or 4 speed manual transmission. Core distributors will have correct stamping of D0OF-V. Original Ford part number D0OF-12127-V. 351 Windsor engines use a smaller distributor gear (about 1-1/4"), Cleveland.distributor gear is about 1-7/16" in diameter.

Used core distributor for 1970 Mercury Cougar and Ford Mustang with Q code 428CJ and automatic transmission. Core distributors will have correct stamping of D0ZF-G. Original Ford part number D0ZF-12127-G.

Used core distributor for 1970 Mercury Cougar and Ford Mustang with 428 Cobra Jet and 4 speed manual transmission. Also fits 428SCJ engines with 4 speed stick. Core distributors will have correct stamping of D0ZF-C. Ford part # D0ZF-12127-C.

This little device may not appear to be all that important, but it has a big job to do when your engine gets too hot. The threaded end looks a bit like an engine temperature sensor, and that's because it is. It's normally mounted on the intake manifold or engine block where it can sense coolant temperature.The three ports at the other end are for vacuum connections. One goes to manifold vacuum, another to carburetor vacuum, and the third goes to the vacuum advance on the distributor. At normal...

Used core distributor for 1969-70 Mercury Cougar and Ford Mustang with G code Boss 302 engine. Core distributors will have correct stamping of C9ZF-E. Original Ford part number C9ZF-12127-E. No vacuum advance included. Current distributor has a date of 9J8, or Sept 8, 1969. Early 1970 build date.

Used Distributor / 351W-2V for the 1970 Mercury Cougar / 1970 Ford Mustang Ford part number D0AF-12127-H  

Factory oil cooler as used on 1969-70 R and Q code Super Cobra Jet 428 engines. Nice used condition, comes as shown with one fitting. Will also work for installing an external oil cooler on the other FE motor applications.Ford part number C9OE-6884-B. 

Replacement "cool white" LED single post light bulb for 67-73 Cougar and Mustang courtesy light applications. Can also be used for trunk lights, under hood lights, under dash lights, and more. Good replacement for 97 and 631 bulb applications. Some may find Our Plasma bulbs too bright for the Opera Lights and prefer to tone it down with these. ...

This used plug end will work on your 69 - 70 Standard or XR7 as well as the 69 - 70 Mustang. This plug housing is used to connect the under dash main loom to the gauge cluster.*Does not include wires

C9ZZ-14A318-A-Used Wire lead for the accessory terminal found optionally on 1969-70 Mercury Cougar and Ford Mustang fuse blocks. Lead comes with factory molded triple female connector for plugging in the various accessories such as 1969 swing away steering column, rear window defogger, speed or cruise control, etc. Wire can be marked with C8OB-14A318-A or C9ZB-14A318-A. NOTE: There are two version of this wire, one is long and the other is short. The shorter version has a smaller gauge wire. ...

C8OZ-14A033-C Brass clip with accessory terminal for attaching the accessory lead wire with multi connector. Missing attaching screw and nut. Attaches to all 1969-73 fuse blocks found on Mercury Cougars and Ford Mustangs. Accessory feed terminal for such things as 1969 swing away steering column, rear window defogger, speed or cruise control, etc. Includes fuse block mounting hardware.*Note - Naked, no machine screw and nut for mounting to fuse block. 

This Autolite capacitor is stamped with part number C6OA-18832-A. It attaches to one of the lugs on the voltage regulator, bullet lead plugs into wiring harness. Sometimes called a radio ignition interference suppressor. About 1-15/16" inches long. This is one of those small detail items that judges like. All Ford and Mercury vehicles from 1966-1971 used this "Autolite" marked capacitor when a radio was installed by the factory. Starting in 1972 there is a Motorcraft version which has a...

This is the electrical portion of the new for 1970, locking column mounted switch. This is the rod actuated device mounted on the top of your column under the plastic collar cover. See page 33-02-06 of your 1970 shop manual for proper installation and adjustment. Working, used ignition switch. This is only the electrical side, the mechanical key and lock section is not included. These are tested and repaired as necessary by our Electrical Dept. Ford part number D0AZ-11572-A. While there's...

Used Autolite water temperature sending unit, fits 351C and Boss 302 engines. 260° stamped, for Mercury Cougar 1970-73, and Ford Mustang 1970-73.  Ford number D0WY-10884-A. *Note - these are specifically NOT for 1969 351W. Ford had a unique part number for that one engine.... and we don't stock that one. Sorry.Check out the video below on our new gauge tester: Check out our video on replacing the fuel system on a '68 Cougar! ...

Used Autolite water temperature sending unit, fits 1970 351W-2V, 428CJ, and 429CJ engines. 258° stamped, for Mercury Cougar 1970-73, and Ford Mustang 1970-73.  Ford number D0ZZ-10884-A. *Note - these are specifically NOT for 1969 351W. Ford had a unique part number for that one engine.... and we don't stock that one. Sorry.Check out the video below on our new gauge tester: Check out our video on replacing the fuel system on a '68 Cougar! ...

Used Autolite water temperature sending unit, fits 1969 Mercury Cougar and Ford Mustang with 351W-2V, 351W-2V engines. Ford number C9WY-10884-A.Check out the video below on our new gauge tester: Check out our video on replacing the fuel system on a '68 Cougar! ...

The automatic seat back release option was added in early 1970 for Cougar and Mustang. The automatic seat back release would pull the release lever on both of the bucket seats. This only happens when the either the driver or passenger side door is opened. Kit comes with the 1970 specific wiring harnesses from the solenoid, includes 3 pin switch for the passenger pillar post, relay, solenoids, and cross over wiring. This option is best added to seats prior to upholstery. We are not sure...

Big bell shaped oil pressure sending unit for 1967-73 Mercury XR7 and 1967-73 Ford Mustang with actual oil pressure gauges instead of idiot light for the oil pressure. *Note - this pressure switch does use the press on wiring boot. Please check your wiring harness for the proper connector. This oil pressure sending unit also fits the following cars that have analog oil pressure gauges: 1969-71 Continental MKIII, Thunderbird 1965-71.Replaced Ford part # C9ZZ-9278-A Check out the video...

Reproduction, non functional "dummy" correct looking rev limiter. Also referred to as an electronic engine governor or RPM limiter. These were used on 1970 BOSS 302 engines. Replaces Ford part number DOZF-12450-B.Note that Ford used a solid state voltage regulator that uses the same case starting in 1966 that has been found on Trucks, Thunderbirds, Galaxies and other full size cars. These units have been known to have engineering numbers of C6AF-10316-A, C6TF-10316-A, and D2HF-10316-AA...

Reproduction, non functional "dummy" correct looking rev limiter. Also referred to as an electronic engine governor or RPM limiter. These were used on 1970 428 Cobra Jet engines when the car was equipped with a manual transmission. Replaces Ford part number DOZF-12450-A.

Used battery clamp to inner fender apron "L" bracket for 69 - 70 Cougars and Mustangs.This bracket secures the battery clamp to the inner fender apron. Ford Part # C9ZZ-10A705-A

Good used group 27 tray for 1969-70 Mercury Cougar or Ford Mustang. Assembly line installed group 27 battery tray. For those that want to keep it very original.Current tray has some erosion on the battery surface from use as shown. One little rust hole in the corner.

Mint condition part that is almost always missing on cars equipped with group 27 battery. Great addition to your 1970 BOSS 302 Eliminator. Also correct for Mustang and Torino. Ford part # D0OZ-10A682-A, casting number as seen on part is D0OB-10A682-A. There is currently no correct reproduction of this part. Click here for more information on this rare part.

This is a reproduction of the original engine displacement decal. Located on the top of the air cleaner. M code 351 4 barrel Cleveland.  NOTE: This decal has a pinkish/orange tint to it. Fits the following models with a 351-4V engine: 1970 Cougar 1970 Mustang

NOS grease cap for front wheels of the Mercury Cougar or Ford Mustang. 2 Required per car, sold individually. New from Ford. Replaces Ford part # B5A-1131-A.

This reproduction emergency / parking brake cable equalizer mounts to the end of the parking brake release assembly and captures the emergency brake cable. A very nice reproduction!Replaces Ford part # C6OZ-2A602-A.

This reproduction emergency / parking brake idler bracket welds to the under side of the floor on the driver side (left hand) of the vehicle and has the factory spec pin.

This passenger side (right hand) reproduction emergency / parking brake cable idler bracket mounts to the right front floor pan. The idler bracket is often discarded when the floor pan is removed for replacement. We also have good used units in stock for those that desire 100% correctness.

Set of 5 reproduction firewall inspection decals. During final inspection, these decals where placed in different locations on the firewall / cowl area and one P decal between the weatherstrip and dash pad inside the drivers door jam. This decal set has the assembly line inspectors names stamped on them. These decals would have been used on cars equipped with Boss 302 and BOSS 429 engines.

New old stock emergency / parking brake pedal pad that features all stainless steel construction. Fits any 1969-73 Mercury Cougar and Ford Mustang.Replaces Ford part # C9ZZ-2A487-C.

Used emergency / parking brake assembly for the Mercury Cougar or Ford Mustang. The 1969 model used a T shaped chrome release handle and 1970 used a black plastic T shaped or chrome release knob. Seldom in stock, please check out the reproduction version. Ford part # D0ZZ-2780-A.

Used hairpin clip for attaching the brake light switch to the brake pedal. This clip was also used to attach the clutch rod to the clutch pedal on manual transmission cars. Fits all years 1967-73, Ford and Mercury.Ford Part # 380699-S

4 oz. tube of non-melting, water resistant grease for disc and drum brake hardware, hood hinges, window regulators, quarter windows, vent window hinges, pretty much whatever needs lubing. A little dab will do ya!Do you have questions about Glue-In vs Bolt-In glass? How about how to properly install Glue-In glass in your 1969 Cougar or Mustang? Check out our video below for some great glassy information!1969 Glue-In Glass: The Comprehensive Repair Guide Video ...

This kit contains all the replacement springs and hold down components required to do a professional job on rear drum brakes. Kit includes enough parts for two wheels. This is for the 9 inch drum brakes commonly found on the early 6 cylinder cars with 7-1/4 inch rear ends.*Note - Kit does not include hardware for rear emergency brakes.

This kit was sold by Ford Service Departments back in the day for those who were tired of their manual drum brakes. This kit includes all you will need to convert your six cylinder Mustang or V8 Cougar / Mustang from manual to power drum brakes. Technically it is correct only for a 1968 but will work on any year 67-70. The conversion carries a Ford part number of C8ZZ-2A091-A. Ford was generous and gave you both a manual transmission and a automatic transmission brake pedal in the kit. When...

C3OZ-1126-B Used brake drum with the vintage casting look. Guaranteed to successfully be turned and not exceed the manufacturers inside maximum of 10.060". When we say the "vintage casting look", we mean with the proper groove and contours. Reproductions are fine, but do not retain the casting design of the original casting company. When looking for used brake drums, the rule of thumb is to find ones with a brake surface area of 1/4 inch more than the brake shoe width.

C9OZ-2211-B Right hand rear brake backing plate for use with 2 inch wide brake shoes. Clean Western part with no heavy corrosion like you see on Eastern cars. Inspected for excessive wear. Used on cars with 10" drums.Originally manufactured by Kelsey-Hayes, KH part number 71085. Originally manufactured by Bendix, part number 317559.

C9OZ-2212-B Left hand rear brake backing plate for use with 2 inch wide brake shoes. Clean Western part with no heavy corrosion like you see on Eastern cars. Inspected for excessive wear. Used on cars with 10" drums.Originally manufactured by Kelsey-Hayes, KH part number 71086. Originally manufactured by Bendix, part number 317558..

Used brake shoe guide plate, or anchor pin, that holds the top of the drum brake shoes together on your Mercury Cougar or Ford Mustang equipped with drum brakes. For the money our reproduction plate is a better value and cleaner, too. These have 1/2 inch holes in them.Replaces Ford part number C4UZ-2028-A.

Used brake shoe guide plate, or anchor pin, that holds the top of the drum brake shoes together on your Mercury Cougar or Ford Mustang equipped with drum brakes. For the money our reproduction plate is a better value and cleaner, too. These have 1/2 inch holes in them.Replaces Ford part number C4UZ-2028-A.

Reproduction brake light switch for Mercury Cougars and Ford Mustangs equipped with manual brakes. Ford originally called these stop lamp switches.Replaces Ford Part #: C9ZZ-13480-A.

Reproduction passenger side (right hand) outer frame rail patch for Mercury Cougar or Ford Mustang.Here's our little film to help you fortify your flexxy feline!

Reproduction passenger side (right hand) torque box outer section for Mercury Cougar and Ford Mustang coupe and convertible.Here's our little film to help you fortify your flexxy feline!

Reproduction passenger side (right hand) torque box for Mercury Cougar and Ford Mustang convertibles.Here's our little film to help you fortify your flexxy feline!

Used driver side grille assembly found in all 1970 Mercury Cougar and Ford Mustang quarter panels inside the door jamb. Grade A used condition, will have all rubber flaps intact, plastic in good condition. B grade used also available.Replaces Ford part number D0ZB-65280B63-A.*Trivia - This part was also used on 1971-73 Mercury Cougars and Ford Mustangs but they swapped sides. This part goes to the driver side of 1971-73 Cougars and Mustangs. The Ford and Mercury Master Parts Catalogs are...

New pair of white and yellow paint sticks for the Mercury or Ford. These units were used by FORD at the assembly plants to mark fender aprons

Full passenger (right hand) side front frame rail that measures 52" long and the outer rail has weld nuts installed for proper installation. Fits: 1967 Mercury Cougar1968 Mercury Cougar1969 Mercury Cougar1970 Mercury Cougar 1967 Ford Mustang1968 Ford Mustang1969 Ford Mustang1970 Ford Mustang ...

Full passenger (right hand) side front frame rail that measures 52" long. Fits: 1967 Mercury Cougar1968 Mercury Cougar1969 Mercury Cougar1970 Mercury Cougar 1967 Ford Mustang1968 Ford Mustang1969 Ford Mustang1970 Ford Mustang ...

Here is our reproduction SPI torque box for the driver side (left hand) of your Mercury Cougar coupe.

Here is our reproduction passenger side (right hand) SPI torque box for your Mercury Cougar coupe.

Universal driver side (left hand) or passenger side (right hand) inner floor frame patch that you can trim to fit the area that needs to be repaired.

Reproduction driver side (left hand) outer front frame patch for Mercury Cougar and Ford Mustang.Here's our little film to help you fortify your flexxy feline!

Full driver (left hand) side front frame rail that measures 52" long. Fits: 1967 Mercury Cougar1968 Mercury Cougar1969 Mercury Cougar1970 Mercury Cougar 1967 Ford Mustang1968 Ford Mustang1969 Ford Mustang1970 Ford Mustang ...

Reproduction inner floor frame rail patch for the Mercury Cougar and Ford Mustang coupe and convertible. As this item is for a Mustang, you will find that you will have to modify it to work with your Cougar. This unit measures 28" long where the Cougar piece is 19". This unit is a 1/4" wider than the Cougar piece as well.

Now you can replace this original part, which is commonly stripped out, with a nice reproduction. Must be welded to floor pan. 6 total per car, 2 inboard in the transmission tunnel, and 4 on the rear seat pans. The front outboard anchors are part of the rocker rails. Rectangular shaped like the 1967-73 cars. We have noticed that the last generation 1971-73 Cougars had 4 round shaped plates in the rear floors. Same threads, all work the same. These were pretty much used on all Ford...

Passenger side (right hand) front seat floor pan. This pan is cut from the full floor pans in order to save on shipping costs when a customer does not need the entire length pan. Cutting from the Dynacorn full length pans means this will be a quality cut, when compared to other pans on the market.   1967-68 style ribbing, works in 1969-70 and can be modified to fit 1971-73. *NOTE* This floor pan has the outside lip bent down which is proper for coupes, convertibles were bent up....

These correct floor pan patches are for the 1969-70 coupe and do not have drain plugs like the 1967-68 panels. These are made from a really rigid steel and do not easily bend or dent easily like many of the offshore pans you find on the market. These 20 gauge panels are 24" long, 15 1/4" wide and a 5/8" flange that butts up against the inner rocker. Great for the person doing a "Correct" restoration on their 1969-70 Cougar / Mustang / Shelby.

These correct floor pan patches are for the 1969-70 coupe and do not have drain plugs like the 1967-68 panels. These are made from a really rigid steel and do not easily bend or dent easily like many of the offshore pans you find on the market. These 20 gauge panels are 24" long, 15 1/4" wide and the ninety degree flange that butts up to the inner rocker is 5/8" tall. Great for the person doing a "Correct" restoration on their 1969-70 Cougar / Mustang / Shelby.

These correct floor pan patches are for the 1969-70 convertible and do not have drain plugs like the 1967-68 panels. These are made from a really rigid steel and do not easily bend or dent easily like many of the offshore pans you find on the market. These 20 gauge panels are 24" long and 15 1/4" wide. Great for the person doing a "correct" restoration on their 1969-70 Cougar / Mustang / Shelby.

Must have for 69-70 convertible owners or anyone else who wishes to tighten up the notoriously weak front inner structure of the 67-70 Cougar / Mustang. All three of these easy to install upgrades are outlined in the BOSS 302 Chassis Modification book that is NOT included in this package. After you install this kit you will wonder how you could have possibly lived this long without it. Even if you already have the one piece export brace, the chances are it is the old ill fitting off-shore...

Must have for 69-70 convertible owners or anyone else who wishes to tighten up the notoriously weak front inner structure of the 67-70 Cougar / Mustang. All three of these easy to install upgrades are outlined in the BOSS 302 Chassis Modification book that is NOT included in this package. After you install this kit you will wonder how you could have possibly lived this long without it. Even if you already have the one piece export brace, the chances are it is the old ill fitting off-shore...

Original used three piece tack strips for the 1969 - 1970 Cougar convertible. Over-sized, must be shipped via UPS.