All Available Parts - 1972 Mercury Cougar

D1ZA-3B153-AA 1971 - 1973 Manual steering pitman arm. May also have casting number D3ZA-3B153-AB. Ford part number D1ZZ-3590-A.

Economy replacement vinyl top that looks great and fits perfect. This economy version top has the fuzzy white backing, not common on the more expensive vinyl tops.

CUSTOM ORDER, DROPSHIP ONLY. A top quality replacement vinyl top that looks great and fits perfect. We talked to the manufacturer about making 1/2 vinyl tops, but they said that they would need to charge the same amount for the 1/2 top and all they would do is just cut the top to the length requested, so their suggestion was to just let customers who need a 1/2 vinyl top purchase the full vinyl top and let them cut the top to the exact dimensions for their top.

CUSTOM ORDER, DROPSHIP ONLY. A top quality replacement vinyl top that looks great and fits perfect. We talked to the manufacturer about making 1/2 vinyl tops, but they said that they would need to charge the same amount for the 1/2 top and all they would do is just cut the top to the length requested, so their suggestion was to just let customers who need a 1/2 vinyl top purchase the full vinyl top and let them cut the top to the exact dimensions for their top.

Rear seat bottom or lower cushion from any 1971-72 Mercury Cougar or Ford Mustang convertible. Minimal rust, solid, just needs clean up and upholstery. We usually leave the upholstery on the frame when we ship. Verify that both of your seat belts anchor under the seat. All of 1973 and possibly late 1972 had the retractor portion of the seat belts in the rear interior panels. That seat belt end, would anchor in the panel area.Replaces Ford part number D1ZB-7663120.*Note - Does not fit coupe or...

Rear seat back or upper cushion from any 1971-73 Mercury Cougar or Ford Mustang convertible. Minimal rust, solid, just needs clean up and upholstery. We usually leave the upholstery on the frame when we ship.Replaces Ford part number D1ZB-7666700.*Note - Does not fit coupe, or fast back.

Rear seat bottom or lower cushion from any 1972-73 Mercury Cougar or Ford Mustang convertible. Minimal rust, solid, just needs clean up and upholstery. We usually leave the upholstery on the frame when we ship. Verify that only two of your seat belts anchor, are under the seat. All of 1973 and possibly late 1972 had the retractor portion of the seat belts in the rear interior panels. That seat belt end, would anchor in the panel area.Replaces Ford part number D3ZB-7663120.*Note - Does not fit...

This is a grade 'A' used mirror assembly with no UV damage and has had the mirror lens "re-silvered". Keep in mind a restored lens that is decades old will look good when finished but almost never flawless as the surface of the glass will usually have light scratches and often faint spotting on the backside from previous water damage / staining. Sold outright, no core required. NOTE: Pictured is black, but if you would like a specific color other than black please mention it in the...

Professional strength adhesive for attaching your rearview mirror bracket to your windshield. Good for 1968 - 1973 Cougars and Mustangs. 1967's Didn't have the bracket attached to the windshield.

Due to time constraints, we can no longer offer the service of having your own mirror restored, this is now an exchange based service only.Any mention of it in the video below is outdated, please disregard. Restored rear view mirror lens for the 68 - 73 Mercury Cougar or Ford Mustang. Unlike our full price restored lenses, these require no core. These lenses look good at first, but if you look close you may see a scratch, tiny chip around the perimeter or discoloration in the lens. If your...

Used bezel for the driver side power seat switch on the 71 - 73 Cougar or Mustang. Ford part number D1ZB-14A706-AA This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of 50% of our web price for parts delivered in hand or by carrier to our Brooks, Oregon location. If you're not interested in store credit, just shoot us an email and we will let you know if it's is something we can...

Grade A used passenger side bucket seat textured plastic trim panel. Available in black, blue, red, ginger, avocado, green, and white. Please specify in the notes your desired color, ginger seems to be the most prolific color, the others may or may not be available. Grade A will not be chalky or have major scuffs or scratches. Various Ford part numbers associated with this panel, here are a few: D12B-6260762, D3ZB-6561632, D1FZ-6260762, D2ZZ-6260762, and D3ZZ-6560762. We also...

Grade A used driver side bucket seat textured plastic trim panel. Available in black, blue, red, ginger, avocado, green, and white. Please specify in the notes your desired color, ginger seems to be the most prolific color, the others may or may not be available. Grade A will not be chalky or have major scuffs or scratches. Various Ford part numbers associated with this panel, here are a few: D12B-6260763, D3ZB-6561633, D1FZ-6260763, D2ZZ-6260763, and D3ZZ-6560763. We also have B...

Core driver side (left hand) and passenger side (right hand) pair of bucket seats with center seat release for the Mercury Cougar or Ford Mustang. The seat frame is the same in the standard, decor or XR7 and are the same driver to passenger side. The foam almost will always be deteriorating, or even missing, and will need to be recovered. These units will be solid core frames taken from a Western parts car. Seat tracks are sold separately. Seat hinge covers and hardware available...

Core driver side (left hand) bucket seat frame with center seat release for the Mercury Cougar or Ford Mustang. This unit is the same driver to passenger side. The foam almost will always be deteriorating, or even missing, and will need to be recovered. These will be solid core frames taken from a Western parts car. Seat tracks are sold separately. Seat hinge covers and hardware available separately. *NOTE* Want to save on shipping? If you only need the bottom portion of the bucket...

This desirable option was used only on the driver side seat of the LATE 71-73 Cougar and Mustang. This is for seats that have the seat release knobs on the outsides of the seats. The early 71's had the release in the center of the seat. It can be installed on the passenger side with no modification other than extending the wiring that runs under the carpet.  Before we send out a system it will have been tested and will work in all positions and will not show excessive wear or...

This passenger side (right hand) moulding is correct for hardtop or coupe. On convertibles, the top portion is trimmed to allow it to slide under the sun visor bracket. Convertibles show the same casting numbers on the part, but are a modified before assembly. We do have factory cut convertible mouldings both early and late. Ford part # D1ZZ-6503598, engineering # imprinted on the back D1ZB-6503598 for 1971-72, D3ZB-6503599 for 1973. *NOTE* Excludes Mustang Fastback and Mach 1 models. This...

This passenger side moulding is correct for convertible. On convertibles the top portion is trimmed to allow it to slide under the sun visor bracket. The engineering number imprinted on the back is D1ZB-6503598 for 1971-1972 and D3ZB-6503599 for 1973. Convertibles show the same casting numbers on the part, but are a modified before assembly. We do have factory cut convertible mouldings both early and late. Ford part # D1ZZ-7603598. *NOTE* Excludes Mustang Fastback and Mach 1 models. ...

There currently are no reproductions of this curved, thin package tray. Included with the tray are both slender strips of thin sound deadener / insulation. These package tray cover boards will not have heavy water damage, but will need paint. Replaces Ford part number D1WY-6546668-A.

Used interior quarter window moulding for the driver side (left hand) of the Mercury Cougar coupe. This trim installs vertically behind the quarter window. Unfortunately we cannot guarantee we will be able to supply the color of your choice, but we will try to accommodate.

This driver side moulding is correct for hardtop or coupe. On convertibles the top portion is trimmed to allow it to slide under the sun visor bracket. The engineering number imprinted on the back is D1ZB-6503599 for 1971-1972 and D3ZB-6503599 for 1973. Convertibles show the same casting numbers on the part, but are a modified before assembly. We do have factory cut convertible mouldings both early and late. Master part number D1ZZ-6503599.*NOTE* - Excludes Mustang Fastback and Mach 1 models. ...

Chrome trim for the upper headlight housing. "L" shaped trim in Grade B used condition, very common to find in this condition. Fits 1971-72 Mercury Cougar only. Grade B trim will have limited pitting or minor road scars. Not quite show quality, but will be unbroken. Driver side upper trim.Replaces Ford part number D1WB-13B165-AA.

NOS Ford replacement passenger side headlight housing for the 1971 - 1973 Mercury Cougar. The 73 headlight housing will fit on 71 - 72, but not vice versa. This is a new in the box original replacement part that inludes the headlight cups and rings. Ford part number D3WY-13008-A

NOS Ford replacement driver side headlight housing for the 1971 - 1973 Mercury Cougar. The 73 headlight housing will fit on 71 - 72, but not vice versa. This is a new in the box original replacement part that inludes the headlight cups and rings. Ford part number D3WY-13008-B

Best used bezel we can find from a Western parts car "Almost" pit free. If you look close you will see some tiny specs. Click onto the image to enlarge the picture.

This is a tough little unit to find in NOS form or grade "A" condition. Most of these will come with some very minor freckling in the chrome. Usually the attaching nuts are missing from the Ford boxes. May or may not include the Ford box, depends on stock.Mercury part # D1WY-16958-A, Mercury casting # D1WB-16958-AA.

Chrome trim for the upper headlight housing. "L" shaped trim in Grade A used condition, very tough to find in this condition, click the 'notify me' tab for email notification of new available stock. Fits 1971-72 Mercury Cougar only. Grade A trim will be pit free, but will have some freckling present. Driver side upper trim.Replaces Ford part number D1WB-13B165-AA.

These are our average used, or Grade B, front license plate mounting bracket that attaches to the passenger side of the bumper of all 1971-72 Mercury Cougars. It may or may not have the rubber anti rattle bumpers present, but will have either original or reproduction plastic inserts for screwing on the license plate. This B grade bracket will function properly, but will have some slight damage or signs of straightening.Replaces Ford part number D1WY-17A385-A.

Chrome driver side (left hand) bezel that wraps around the outside of the front turn signal lens on the 1971 or 1972 Mercury Cougar. This bezel will be blemished. Blemishes could include cracks, pitting, or bends. Will not be missing any pieces. Ford part # D1WB-13237-AA.*NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is the designer of all of our solid state sequential...

No Excuses chrome bezel that wraps around the outside of the front turn signal lens on the 1971 or 1972 Mercury Cougar. Ford part # D1WB-13237-AA.*NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is the designer of all of our solid state sequential systems. There is no question he cannot answer! Here is a link to a great source of information on the subject.Here's our...

No excuses passenger side (right hand) chrome bezel that wraps around the outside of the front turn signal lens on the 1971 or 1972 Mercury Cougar. Ford part # D1WB-13236-AA.*NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is the designer of all of our solid state sequential systems. There is no question he cannot answer! Here is a link to a great source of information...

This grille will be less than perfect with one or two cracks, bend showing and pitting. A Grade "B" will not be cracked around the perimeter and will not be missing any pieces. Good for a driver quality car. This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of 50% of our web price for parts delivered in hand or by carrier to our Brooks, Oregon location. If you're not interested in...

This grille will be less than perfect with one or two cracks, bend showing and pitting. A Grade "C" WILL be cracked around the perimeter, but will not be missing any pieces. Good for a driver quality car.

Easy to install kit that converts your two speed wiper system to a variable speed system. These "off shore" units are spotty at best. We recommend our good used unit which you can get right here.

Made by Trico who made them originally for Ford. Replaces Ford part #: D1ZZ-17528-A. Sold individually

These are our best used front license plate mounting bracket that attaches to the passenger side of the bumper of all 1971-72 Mercury Cougars. It may or may not have the rubber anti rattle bumpers present, but will have either original or reproduction plastic inserts for screwing on the license plate.Replaces Ford part number D1WY-17A385-A. This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store...

Very good used door glass with no deep scratches (multiple faint scratches and water spots often will be present). Not perfect but the best you could expect to find from a 50 year old plus parts car and will of course be a better fit than repro. For those wanting Grade "A" glass, we recommend calling us so we can discuss with you the glass that we have available.Need a little help identifying some of the markings on your glass? Check out the Guide to Original Date Coded Glass - Mustang, Boss,...

These Spark Plug Wire Separators are made of high-quality ABS plastic. Constructed to hold both standard 7mm and 8mm high-performance spark plug wires. Fits directly on valve cover clip. Available in blue, red and OE black.

Quality U.S.A. made hose with concours repeating GAS markings. Also include OEM mounting hardware. Replaces Ford Part #: C7ZZ-9327-A. Check out our video on replacing the fuel system on a '68 Cougar! ...

Used plastic clip for the Mercury Cougar or Ford Mustang.

All of our used insulation hood pads are guaranteed to be filthy dirty, less than perfect (as shown) and include at least one spider. We cannot fold these to ship them and they are too large for UPS. You must pick them up in person or we can ship them for free when you purchase a hood from us.

New gaskets for installing your intake manifold. This is the Felpro branded gasket. Fits all 1970-73 Ford 351C engines with 2 barrel intake manifolds 1969-70 Mercury Cougar and Ford Mustang with 351C-2V engines. This gasket set includes a metal pan gasket.Any doubts? 351 Windsor engines have 6 bolts holding the valve covers in place. 351 Cleveland engines have 8 bolts holding down the valve covers.*Note - Excludes 351W engines. *Note - Excludes 351C-4V Cleveland engines. ...

Good used original distributor for the 351 Cobra Jet. Ford Part # D2ZF-12127-GA.

Good used original distributor for the 351 Cobra Jet. Ford Part # D2ZF-12127-GB.

Reproduction hold down clamp rivet for the 67 - 73 Cougar or Mustang. This rivet holds the clip / clamp onto the distributor. Sold individually, 2 per car.

New rubber "O" ring for Ford V-8 distributors from 289/302/351W/351C/429 engines.

Pertronix brand 7mm spark plug wires. These are performance oriented wires compared to the concours spark plug wires. For any 1967-73 Mercury Cougar and Ford with 289 or 302 engines. Black wires and boots, quality spark plug wires taylor made for the small block Ford engines. Recommended by Pertronix for use with the Flame Thrower coils.

Pertronix brand 7mm spark plug wires. These are performance oriented wires compared to the concours spark plug wires. For any 1967-73 Mercury Cougar and Ford with 351 - 390- 428 - 429 engines. Black wires and boots, quality spark plug wires taylor made for 351 engines and the big block Ford engines. Recommended by Pertronix for use with the Flame Thrower coils.

Powerful oil filled coil that generates 40,000 volts, designed to work with the either of our Pertronix Ignitors. Sold in black or chrome. *Note - This coil is not necessarily needed with the Pertronix Ignitors, the stock Ford coil works fine for most applications.

Concours correct Autolite spark plug wires for any 1972-73 Mercury Cougar Eliminator or Ford Mustang with 351C engines. Black wires with 'Motorcraft', 'SIPCON', and the cylinder numbers individually imprinted on the 7mm wires. Orange spark plug boots on this set.

Cast iron intake manifold used on all 1972 Q code 351-4V or 351CJ engines in a Mercury Cougar or 1971-72 Ford Mustang. Stock 4 barrel spread bore intake manifold. Take off manifold with correct casting number of D1ZE-9425-BB . Intake shipped bare, less carburetor studs, heater tube, vacuum fittings, and water neck where applicable. Ford master part number D1ZE-9425-BB. *Note - 351 Cleveland engines only.

Good used original distributor for the 351 Cobra Jet. Ford Part # D2ZF-12127-EA.

Good used original distributor for the 351 Cobra Jet. Ford Part # D2ZF-12127-HA.

Good used original distributor for the 351 Cobra Jet. Ford Part # D2ZF-12127-HB.

Good used original distributor for the 351 Cobra Jet. Ford Part # D2ZF-12127-FA.

This little device may not appear to be all that important, but it has a big job to do when your engine gets too hot. The threaded end looks a bit like an engine temperature sensor, and that's because it is. It's normally mounted on the intake manifold or engine block where it can sense coolant temperature.The three ports at the other end are for vacuum connections. One goes to manifold vacuum, another to carburetor vacuum, and the third goes to the vacuum advance on the distributor. At normal...

This is a restored taillight housing assembled in-house. Complete assembly with new sockets and repaired pigtails in place. Reflective background has been re-painted silver. No major cracks or chips, every unit is thoroughly tested. NOTE: 71-72 housings will not work on the 73, and vice versa. While you're at it, you can grab some new gaskets here. Ford Part Number: D1WB-13441-AA ...

This is a restored taillight housing assembled in-house. Complete assembly with new sockets and repaired pigtails in place. Reflective background has been re-painted silver. No major cracks or chips, every unit is thoroughly tested. NOTE: 71-72 housings will not work on the 73, and vice versa. While you're at it, you can grab some new gaskets here. Ford Part Number: D1WB-13440-AA ...

Good used original distributor for the 351 Cleveland with a 2 barrel carburetor. Ford Part # D2ZF-12127-CA.

Good used original distributor for the 351 Cleveland with a 2 barrel carburetor. Ford Part # D2AF-12127-KA.

Good used original distributor for the 351 Cleveland with a 2 barrel carburetor. Ford Part # D2ZF-12127-AA.

NOTE: WE SUGGEST LOCAL PICK UP ONLY FOR CORE ENGINE BLOCKS BECAUSE WE CANNOT GUARANTEE BLOCKS WILL NOT HAVE CRACKS INTERNALLY. Long block, factory Q code 351CJ-4V V-8 engine. 351 Cleveland engine rated at 266 Hp with 8.0:1 compression ratio in 1972. 4 Bolt main caps on these engine blocks. Likely 0.030" bored motor that may or may not have been in running condition when pulled. Guaranteed to be rebuildable. Complete engine less carburetor, exhaust manifolds, fan, distributor, accessories,...

NOTE: WE SUGGEST LOCAL PICK UP ONLY FOR CORE ENGINE BLOCKS BECAUSE WE CANNOT GUARANTEE BLOCKS WILL NOT HAVE CRACKS INTERNALLY.Used standard bore 4.00" Ford 351C 1971-73 engine block. Will be used, dirty, have measurable taper, and will have a ridge. Good for rebuild. Bare block, may have D0AE, D2AE, castings. When we have them in stock we will post the casting date or dates. Heavy, will require either local pickup or freight shipping. Dated 2C7 or March 7, 1972. D2AE-6015-CA.This item...

Complete assembly with good sockets and pigtails in place. No cracks or chips, every unit is thoroughly tested.Ford Part Number: D1WB-13441-AA

Complete assembly with good sockets and pigtails in place. No cracks or chips, every unit is thoroughly tested.Ford Part Number: D1WB-13440-AA

Grade "B" 1971-72 passenger side tail light lens. Grade B lens will have 1 or 2 blemishes which may include a small crack, chip, discoloration, or other defect.  Replaces Ford part number D1WY-13450-A. *NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is the designer of all of our solid state sequential systems. There is no question he cannot answer! Here is a...

Used battery tray, may not be exactly like the assembly line tray. Group 27 battery tray is typical for cars with air conditioning and higher amp alternators. Fits 1971-73 Mercury Cougar and Ford Mustang. Also 1970-71 Ford Torino and Mercury Cyclone and variants of the B or C midsize Ford and Mercury bodied cars. Used condition, minor pitting as shown. Replaces Ford Part #: D0OZ-10732-B.

We have a very difficult time keeping grade "A" tail light lenses in stock. This lens is prone to cracking in between the clear and red portion of the lens. Let us know if you have extras to sell or trade!*NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is the designer of all of our solid state sequential systems. There is no question he cannot answer! Here is a link to...

Replacement "cool white" LED single post light bulb for 67-73 Cougar and Mustang courtesy light applications. Can also be used for trunk lights, under hood lights, under dash lights, and more. Good replacement for 97 and 631 bulb applications. Some may find Our Plasma bulbs too bright for the Opera Lights and prefer to tone it down with these. ...

Used Autolite water temperature sending unit, fits 351C and Boss 302 engines. 260° stamped, for Mercury Cougar 1970-73, and Ford Mustang 1970-73.  Ford number D0WY-10884-A. *Note - these are specifically NOT for 1969 351W. Ford had a unique part number for that one engine.... and we don't stock that one. Sorry.Check out the video below on our new gauge tester: Check out our video on replacing the fuel system on a '68 Cougar! ...

Reproduction battery powered  (AA battery) scratch built clock. Great alternative for those without a core for rebuild. American made reproduction console clock. Adjustment to clock is made from the reverse side of the clock, there is no stem through the lens for adjustment. Illumination of the dial is through the factory harness. Includes new lens and battery. No Core Required! Quartz movement clocks have second hands that click around, original clocks had a constant sweep...

New temperature sending unit for the 1970 - 1973 Mercury Cougar and Ford Mustang with an actual temperature gauge. Fits 351C and 351W engines. Temp Sender Switch Temp Rating : 22.7-25.5 Ohms Resistance At 220 Deg F Temperature Switch Thread Size : 3/8" x 18 NPTF Replaces Ford Part #: D0WY-10884-A (SW-924)Check out the video below on our new gauge tester: ...

1971 - 1973 Mercury Cougar Ford Mustang rectangular clock found optionally in the center console. Used clocks generally do not work after 36 years. These are considered cores. We also offer clocks with modern quartz movements or NOS movements in restored clocks.Ford Part Number: D1ZZ-15000-C. This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of 50% of our web price for parts delivered...

Good Used Clock Harness for the 1971, 1972 or 1973 Mercury Cougar or Ford Mustang Mach 1. Wiring harness, or pigtail that goes from the back of the clock to the main under dash wiring harness, and ashtray light socket and shroud. The Mustang wiring harness for the clock generally does not include the light socket for the ashtray. The MPC indicates that the Mach 1 did receive this Cougar wiring harness. Ford part number: D1WY-15A006-A and D1WB-15A006-A.

Big bell shaped oil pressure sending unit for 1967-73 Mercury XR7 and 1967-73 Ford Mustang with actual oil pressure gauges instead of idiot light for the oil pressure. *Note - this pressure switch does use the press on wiring boot. Please check your wiring harness for the proper connector. This oil pressure sending unit also fits the following cars that have analog oil pressure gauges: 1969-71 Continental MKIII, Thunderbird 1965-71.Replaced Ford part # C9ZZ-9278-A Check out the video...

Used Wire lead for the accessory terminal found optionally on 71 - 73 Mercury Cougar and Ford Mustang fuse blocks. Lead comes with factory molded triple female connector for plugging in the various accessories such as 1969 swing away steering column, rear window defogger, speed or cruise control, etc. Wire will be marked with D1AB-14A318-AB

C8OZ-14A033-C Brass clip with accessory terminal for attaching the accessory lead wire with multi connector. Missing attaching screw and nut. Attaches to all 1969-73 fuse blocks found on Mercury Cougars and Ford Mustangs. Accessory feed terminal for such things as 1969 swing away steering column, rear window defogger, speed or cruise control, etc. Includes fuse block mounting hardware.*Note - Naked, no machine screw and nut for mounting to fuse block. 

The following excerpt was taken from the advance summary sheets mailed to dealers in 66 and 67.- "For when your customer feels like putting his foot down! Cougar has got a heart of "GO" - just as it comes from the factory. But there are bound to be buyers who will get under the hood to sharpen Cougar's claws. To satisfy the needs of these high performance buffs, here are a number of performance equipment items designed especially for Cougar by Shelby American, Inc. We suggest you stock a...

Mint condition part that is almost always missing on cars equipped with group 27 battery. Great addition to your 1970 BOSS 302 Eliminator. Also correct for Mustang and Torino. Ford part # D0OZ-10A682-A, casting number as seen on part is D0OB-10A682-A. There is currently no correct reproduction of this part. Click here for more information on this rare part.

Everything you need to hold the battery down on your 71 -73 Cougar or Mustang. Included in this kit are the two stainless steel J-bolts, the hold down bracket and the hold down clamp.

This is the 100% correct Ford original battery hold down clamp. Stamped with D0OB10755A. Ford Part #: D0OZ-10718-B. Note: The battery hold down clamp offered by many Mustang / Cougar vendors as "Concours Correct" is actually for the 1974 - 1978 Cougar /  Mustang.

Used hairpin clip for attaching the brake light switch to the brake pedal. This clip was also used to attach the clutch rod to the clutch pedal on manual transmission cars. Fits all years 1967-73, Ford and Mercury.Ford Part # 380699-S

This bracket connects the battery hold down clamp to the fender apron to stop the battery from rocking from side to side. Most cars are missing this crucial part to stabilize the battery. Replaces Ford Part #: D0OZ-10757-A.

This used emergency / parking brake cable connector is for the Mercury Cougar only. That is because it is longer than the Mustang version due to the Cougar's longer wheelbase. This connector connects the two ball ends of the long and short emergency brake cables. Ford part # C7WY-2A790-A.

New old stock emergency / parking brake pedal pad that features all stainless steel construction. Fits any 1969-73 Mercury Cougar and Ford Mustang.Replaces Ford part # C9ZZ-2A487-C.

Used grade "A" emergency / parking brake release handle with bezel and cable for the Mercury Cougar. This unit fits both the Standard and XR7. Our grade "A" part will have a good cable sheath and the chrome on the release handle will be very nice, but not perfect. Ford Part Number: D1WY-2760-A or D1WY-2A760-A This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of 50% of our web...

This reproduction emergency / parking brake idler bracket welds to the under side of the floor on the driver side (left hand) of the vehicle and has the factory spec pin.

This passenger side (right hand) reproduction emergency / parking brake cable idler bracket mounts to the right front floor pan. The idler bracket is often discarded when the floor pan is removed for replacement. We also have good used units in stock for those that desire 100% correctness.

Reproduction brake light switch for the Mercury Cougar and Ford Mustang equipped with manual brakes. High quality replacement part, but the appearance is not original. Ford originally called this unit the stop lamp switch. Replaces Ford part # D1ZZ-13480-A.Here are some pictures of the 2008 Prowl Show hosted by the Cascade Cougar Club. Click on images to enlarge. ...

This is the gear on the upper side of the gearbox. The cables go over each side of the gear.NOTE: Be sure the gear is in good condition so your cables don't get worn out!

4 oz. tube of non-melting, water resistant grease for disc and drum brake hardware, hood hinges, window regulators, quarter windows, vent window hinges, pretty much whatever needs lubing. A little dab will do ya!Do you have questions about Glue-In vs Bolt-In glass? How about how to properly install Glue-In glass in your 1969 Cougar or Mustang? Check out our video below for some great glassy information!1969 Glue-In Glass: The Comprehensive Repair Guide Video ...

Used brake shoe guide plate, or anchor pin, that holds the top of the drum brake shoes together on your Mercury Cougar or Ford Mustang equipped with drum brakes. For the money our reproduction plate is a better value and cleaner, too. These have 1/2 inch holes in them.Replaces Ford part number C4UZ-2028-A.

Used brake shoe guide plate, or anchor pin, that holds the top of the drum brake shoes together on your Mercury Cougar or Ford Mustang equipped with drum brakes. For the money our reproduction plate is a better value and cleaner, too. These have 1/2 inch holes in them.Replaces Ford part number C4UZ-2028-A.

Steel tubing features tin/lead coating and plated zinc chromate fitting and are exact copies of the originals with color coded fittings.

Used passenger side (right hand) sunroof cable for the Mercury Cougar. We have a really hard time keeping these units in stock. Keep in mind this same basic cable design was used on many makes including Porsche, BMW, Mercedes and several other cars through the early 1980's. The same basic design (minor changes through the years) was used on Lincolns, Thunderbirds and other Ford products through the mid seventies. We are buyers of used sunroof cables, motors and misc parts so keep us in mind...

Used driver side (left hand) sunroof cable for the Mercury Cougar. We have a really hard time keeping these units in stock. Keep in mind this same basic cable design was used on many makes including Porsche, BMW, Mercedes and several other cars through the early 1980's. The same basic design (minor changes through the years) was used on Lincolns, Thunderbirds and other Ford products through the mid seventies. We are buyers of used sunroof cables, motors and misc parts so keep us in mind you...

Used inner and outer driver side (left hand) wheel house as cut from a 1971-73 Mercury Cougar parts car. This is a hard part for us to obtain as we have to sacrifice all surrounding parts to remove it in its entirety. The almost always will have a substantial amount of rust showing at the very tips of the outers where they end behind the wheel. If you want to save shipping costs we can sacrifice the inner wheel house and sell you only the outer portion. Used inner and outer driver side...

Crating Fee Applies To This Item. You will be contacted once your order is reviewed to discuss the crating fee. Crating fees generally run between $175 - $250 (this does not include truck freight charges). If an item has a crating fee, this usually indicates that it must ship via Truck Freight and can only be shipped to US addresses and select Canadian addresses. Since we never have all years and sides in stock at any given time in Grade "A" form, and since almost every panel has "some" minor...

Our grade "A" fenders are truly what you would expect from an "A" rated part! We never get returns on our grade "A" fenders which is very important considering the shipping costs involved. Grade "A" fenders have no rust or excessive filler and nothing more than dings or light scrapes for damage. When you turn it over you will not see anything more than light surface rust, no distorted wheel lip areas from over sized tires. We really inspect the area where the fender extension bolts on well as...

Used original FoMoCo upper cowl cut for all 1971-73 Mercury Cougars and Ford Mustangs without A/C. Bear in mind that the inner metal section, or the undersides, did not get paint and is the upper cowl section as shown. A/C cars differ, they have a fresh air duct arrangement. Note that this part will not be perfect and will require hours of spot weld removal due to how large we cut them. The shipping will also be much more than our repro. We highly suggest buying the repro as it is a direct...