All Available Parts - 1973 Mercury Cougar

This group of parts mounts to the top of the AT shifter arm and rides against the thumb activated button on your T shift handle. Its function is to lift the cable that runs through the chrome shifter stem to lock and unlock the shifter out of Park. The Ford technical name for this part is 'Roller - Shift Lever Lock'. We carefully inspect each part to make sure it is in perfect used condition. Ford part number C5ZZ-7D328-A. Check out our video on rebuilding your shifter below: ...

This gives the thumb release button in your T shaped shift handle its tension. If it is rusted then your button will not return back to its outer position easily. Fits 1967-73 Mercury Cougar and 1965-73 Ford Mustang. Technically this spring fits all Ford and Mercury floor shifters 1965-73. Ford part number C5ZZ-7C300-A. The MPC shows this spring to have a free length of 2-1/16 inches.

Automatic shifter cable with slot on the threaded end for all 1969-73 Mercury Cougar and Ford Mustangs. Will also work on 1967-68 but features a slot at bottom so as to remove or adjust easily. The 1967-68 version did not have this slot. Ford part number C9ZZ-7D246-A with the slotted threaded stud on the end. Also fits 1971+ Maverick & Comet with automatic floor shifters. Restoration Hint - We suggest purchasing this upgraded cable for use in 1967-68 shifter levers. Much easier to install, and...

This keeper affixes to the top of the plastic indicator arrow.  Screws included. Check out our video on rebuilding your shifter below: ...

This fragile little plastic arrow is illuminated by the little bulb in your shifter housing. Fits 1969-73 Mercury Cougar and Ford Mustang. Also fits 1971 and newer Pinto, Bobcat, Maverick and Comet with floor shift automatic transmissions. Ford part number C9ZZ-7A110-A. Check out our video on rebuilding your shifter below: ...

Lamp diffuser for all 1969-73 Mercury Cougar and Ford Mustangs. Note the comparison picture. The reproduction is a shade or two lighter than original. The complete Ford part number is not available, the basic part number for this item is 15811. Check out our video on rebuilding your shifter below: ...

Bare automatic shifter bucket or housing. Fits all 71 -73 Mercury Cougar and Ford Mustangs with or without console. Also fits 1971+ Maverick and Comet with automatic floor shifters. If one runs with really worn shifter bushings for too long the hole in the side that the shifter arm passes through may be worn beyond tolerances. Ford part number D1ZZ-7A306-A. We inspect the shift detentes and the hole where the bushings go for wear. This bucket is different than the 1969-70 version as shown on...

Very nice chrome on this used shifter lever for automatic transmissions. Can fit all 1969-73 Mercury Cougar and Ford Mustangs with FMX or C-6 automatic transmissions. We have found that there is an early and a late version of these levers. The late versions used the C9ZZ-7C442-A pawl. The easiest way to determine which is early or late is the width of the slot at the bottom of the lever. If one nickel fits into the slot, it is early. Two nickels will easily fit into the later slot. Bare...

This arm is attached to your automatic transmission floor shifter (see picture at left). Fits all 1969-70 Mercury Cougar and Ford Mustang. Ford calls technical name for this part is 'Arm, Support'. These used parts will come with an intact bushing and nut. Correct for FMX and C-6 transmissions. Ford part number C9ZZ-7302-A. This part may have the course threads or fine threads. Normally this item ships with the course threads. We also stock the 1971-73 version that has a captured stud for...

Complete chrome automatic shifter lever assembly for any 1969-73 Mercury Cougar or Ford Mustang with or without consoles. This is the early version with small width pawl. Good used part no heavy pitting on the chrome, we sell these levers with installed cable, pawl, spring, and gear release assembly. Ford part number for the lever is C9ZZ-7210-A. *Note - Chromed lever and internals only, no T handle. Check out our video on rebuilding your shifter below: ...

Complete chrome automatic shifter lever assembly for any 1969-73 Mercury Cougar or Ford Mustang with or without consoles. This is the late version with wider width pawl. Good used part no heavy pitting on the chrome, we sell these levers with installed cable, pawl, spring, and gear release assembly. Ford part number for the lever is C9ZZ-7210-C. *Note - Chromed lever internals only, no T handle. Check out our video on rebuilding your shifter below: ...

Allen head set screw for all stock Ford automatic shifter handles on any 1967-73 Mercury Cougar or Ford including Mustang. Uses the same 3/32 inch allen wrench for attaching as the originals. Most handles take two of these set screws, one on the dummy button, and one to attach to the top of the shifter lever. The 1973 all chrome shift handle only uses one of these set screws. Original Ford part number 374985-S. Check out our video on rebuilding your shifter below: ...

Reproduction of the little plastic shift indicator arrow, that is illuminated by the little bulb in your shifter housing. Fits 1969-73 Mercury Cougar and Ford Mustang. Also fits 1971 and newer Pinto, Bobcat, Maverick and Comet with floor shift automatic transmissions. Ford part number C9ZZ-7A110-A. Check out our video on rebuilding your shifter below: ...

Restored chrome automatic shifter lever for some 1970 Mercury Cougar or Ford Mustang, and all 1971-73 Cougar and Mustangs, with or without consoles. Sometime in the 1970 era, Ford switched to a larger pawl. Easy to identify if you look at the slit on the lever. We sell these bare for those car owners that have pitted shifter levers. Ford part number C9ZZ-7210-C. *Note - Chromed lever only, sold without cable, pawl, handle, etc. Check out our video on rebuilding your shifter below: ...

Restored shifter T handle as found on all 1973 Mercury Cougar or Ford Mustang with automatic transmissions. This handle will actually fit on most Ford automatic floor shift levers of the era. Design is a little more ergonomic in design, compared to earlier designs. Core charge applies.Replaces Ford part number D3OZ-7213-A.

Exact reproduction for the 1969 - 1973. Perfect fit and finish. You may want to replace yours with this inexpensive unit just for the fresh new luster alone. Your plastic end buttons may have faded to gray but they were originally black like this one. Replaces Ford Part #: C8OZ-7213-A, C90Z-7213-B, D3OZ-7213-A. Check out our video on rebuilding your shifter below: ...

This arm is attached to your automatic transmission floor shifter. Fits all 1969-73 Mercury Cougar and Ford Mustang. Ford calls technical name for this part is 'Arm, Support'. This used part will come with a captured lower stud for attaching the shift rod as shown. Correct for FMX and C-6 transmissions. This version is found on 1972-73 cars, it has the captured lower stud for mounting the automatic shift rod to the transmission. Ford part number D1ZZ-7302-A. Check out our video on rebuilding...

Black plastic selector button for all 1973 Mercury Cougar and Ford Mustang with automatic transmission. It does not fit with the 1968-72 chromed T-handle.  Check out our video on rebuilding your shifter below: ...

Not a very good color match for Cougar owners, but will work well with blue interiors.Stunning quality and far less likely to crack than the originals. The 67 version was actually a little different than 68 - 73 but you would have to look close to see the difference. Check out our video on rebuilding your shifter below: ...

Reproduction console shift assembly for the 69 - 73 Cougar or Mustang. Included in this kit are the T-shifter assy, lever assy, housing and the shifter arm, seals and hardware. Replaces Ford part numbers: C7ZZ-7210C C7ZZ-7A306A C7ZZ-7302A C7ZZ-7213M Check out our video on rebuilding your shifter below: ...

Reproduction engine block spacer plate for 69 - 73 Cougars or Mustangs with 351 engines and 3 or 4 speed manual transmissions. According to the Master Parts Catalog, it also fits 164 tooth bellhousings on 1968-70 with 302 engines too. We also stock the early version from 1968 and 157 tooth versions.

Formed metal clip that holds the gear end into any transmission. Automatic codes W - C4, X - FMX, U - C6, 1 - 3 speed manual, 5 or 6 - 4 speed manual.

Unlike previous reproductions this has the correct grommet that passes through the firewall.  Replaces Ford Part #: C9ZZ-17260-A.  This cable measures 58 1/2" at its very most outer ends.

Made out of Nylon. Please confirm teeth count and direction of teeth. Color codes do not guarantee direct replacement. 4 speed Toploaders have reversed tooth direction. Click here to use our Speedometer Gear Calculator. Available in 16, 17, 18, 19, 20, 21, and 23 tooth*. Replaces Ford Part: C0DZ-17271-A, C0DZ-17271-B, C0DZ-17271-C, C0DZ-17271-D, C0DD-17271-A, C1DZ-17271-A * - 23 tooth gears are not a Ford part and only have a life expectancy of 25,000 miles. They also have been reported to...

Made out of Nylon. Please confirm teeth count and direction of teeth. Color codes do not guarantee direct replacement. 4 speed Toploaders have reversed tooth direction. Click here to use our Speedometer Gear Calculator. Available in 16, 17, 18, 19, 20, 21, and 23 tooth*. Replaces Ford Part: C0DZ-17271-A, C0DZ-17271-B, C0DZ-17271-C, C0DZ-17271-D, C0DD-17271-A, C1DZ-17271-A * - 23 tooth gears are not a Ford part and only have a life expectancy of 25,000 miles. They also have been reported to...

Made out of Nylon. Please confirm teeth count and direction of teeth. Color codes do not guarantee direct replacement. 4 speed Toploaders have reversed tooth direction. Click here to use our Speedometer Gear Calculator. Available in 16, 17, 18, 19, 20, 21, and 23 tooth*. Replaces Ford Part: C0DZ-17271-A, C0DZ-17271-B, C0DZ-17271-C, C0DZ-17271-D, C0DD-17271-A, C1DZ-17271-A * - 23 tooth gears are not a Ford part and only have a life expectancy of 25,000 miles. They also have been reported to...

Made out of Nylon. Please confirm teeth count and direction of teeth. Color codes do not guarantee direct replacement. 4 speed Toploaders have reversed tooth direction. Click here to use our Speedometer Gear Calculator. Available in 16, 17, 18, 19, 20, 21, and 23 tooth*. Replaces Ford Part: C0DZ-17271-A, C0DZ-17271-B, C0DZ-17271-C, C0DZ-17271-D, C0DD-17271-A, C1DZ-17271-A * - 23 tooth gears are not a Ford part and only have a life expectancy of 25,000 miles. They also have been reported to...

Made out of Nylon. Please confirm teeth count and direction of teeth. Color codes do not guarantee direct replacement. 4 speed Toploaders have reversed tooth direction. Click here to use our Speedometer Gear Calculator. Available in 16, 17, 18, 19, 20, 21, and 23 tooth*. Replaces Ford Part: C0DZ-17271-A, C0DZ-17271-B, C0DZ-17271-C, C0DZ-17271-D, C0DD-17271-A, C1DZ-17271-A * - 23 tooth gears are not a Ford part and only have a life expectancy of 25,000 miles. They also have been reported to...

Made out of Nylon. Please confirm teeth count and direction of teeth. Color codes do not guarantee direct replacement. 4 speed Toploaders have reversed tooth direction. Click here to use our Speedometer Gear Calculator. Available in 16, 17, 18, 19, 20, 21, and 23 tooth*. Replaces Ford Part: C0DZ-17271-A, C0DZ-17271-B, C0DZ-17271-C, C0DZ-17271-D, C0DD-17271-A, C1DZ-17271-A * - 23 tooth gears are not a Ford part and only have a life expectancy of 25,000 miles. They also have been reported to...

Made out of Nylon. Please confirm teeth count and direction of teeth. Color codes do not guarantee direct replacement. 4 speed Toploaders have reversed tooth direction. Click here to use our Speedometer Gear Calculator. Available in 16, 17, 18, 19, 20, 21, and 23 tooth*. Replaces Ford Part: C0DZ-17271-A, C0DZ-17271-B, C0DZ-17271-C, C0DZ-17271-D, C0DD-17271-A, C1DZ-17271-A * - 23 tooth gears are not a Ford part and only have a life expectancy of 25,000 miles. They also have been reported to...

Speedometer cable that fits all 1969-73 Mercury Cougar and Ford Mustang with C-6 transmissions. This replacement cable is longer than the originals and does not have the firewall grommet. This cable measures 80" inches in length. Does not include speedometer gear, has correct style plastic clip that attaches to the back of the speedometer. Replaces Ford part # C9ZZ-17260-B, D0ZZ-17260-D, and D1ZZ-17260-G.

Used clip with bolt for attaching the speedometer cable to the transmission of the Mercury Cougar or Ford Mustang. This unit holds the gear end into both automatic and manual transmissions. Automatic codes W - C4, X - FMX, U - C6, 1 - 3 speed manual, 5 or 6 - 4 speed manual.

Reproduction transmission cooling lines made from OE steel for the Mercury Cougar or Ford Mustang equipped with the FMX automatic transmission and 351 engine.

Reproduction transmission cooling lines made of stainless steel for the Mercury Cougar equipped with the FMX automatic transmission and 351 engine. These lines are sold in pairs.

Reproduction transmission cooling lines made of Stainless Steel for the Mercury Cougar equipped with the C-6 automatic transmission and 351 engine. These lines are sold in pairs.

OE Steel Modulator Vacuum Line for all V8 engines with a C6 transmission except 429CJ or the 351C with a 4 barrel carburetor.

Stainless Steel Modulator Vacuum Line for all V8 engines with a C6 transmission except 429CJ or the 351C with a 4 barrel carburetor.

Reproduction Stainless Steel FMX Transmission Modulator Line for the 1972-1973 Mercury Cougar or Ford Mustang

Stainless Steel Transmission Modulator Line for the 1973 Mercury Cougar with a 351 Cleveland, a 4 barrel carburetor, and a C-6 Transmission.

Reproduction OE Steel Transmission Modulator Line for the 1972-1973 Mercury Cougar or Ford Mustang with a 351 and a FMX Transmission.

OE Steel Transmission Modulator Line for the 1973 Mercury Cougar with a 351 Cleveland, a 4 barrel carburetor, and a C-6 Transmission.

Used transmission line adapter and check valve for all FMX transmissions. This fitting goes into the rear part of the transmission case and connects the rear most cooling line to the case. Has internal ball check valve to prevent fluid from back flowing. All FMX transmissions 1969-73 Mercury Cougar or Ford Mustang. The male threads going into the transmission case are 1/2-20 pipe threads.Replaces Ford part number C3AZ-7D174-A.

Reproduction transmission cooling lines made of Stainless Steel for the Mercury Cougar equipped with the C-6 automatic transmission and 351 engine. These lines are sold in pairs.

Rod used for locking the FMX transmission in "Park". Connects to the lower tab of the steering column and the FMX transmission shift arm. Prevents the transmission from shifting out of park when the ignition key is removed. Rod is about 13 inches long and was originally marked with a yellow mark. Casting number stamped on rod - D1ZA-7E330-AA. The FMX, automatic transmission, was used on all 1971 - 1973 Cougars with the 351-2V engine (Letter "H" in the 5th position of your VIN). Transmission...

Rod used for locking the C-6 transmission in "Park". Connects to the lower tab of the steering column and the C-6 transmission shift arm. Prevents the transmission from shifting out of park when the ignition key is removed. Rod is about 13 inches long and was originally marked with a red paint mark or daub. Casting number stamped on the rod - D1ZA-7E330-BA. The C-6, automatic transmission, could be ordered with any engine from 1971 - 1973. Transmission code "U" on your door data tag.

Replacement transmission pan filter and pan gasket kit. For the C-6 (U Code) transmission. Replaces Ford Part Number: C7ZZ-7A098

Original dipstick tube originally painted blue and approximately 19-29/32" inches long. Application 1973 Mercury Cougar or Ford Mustang with FMX automatic transmissions, code "X" on your door data plate. Ford master part number D3ZZ-7A228-B.

Reproduction automatic shifter lever in chrome for the Mercury Cougar or Ford Mustang. Comes with inside cable parts. See the related items for more of your shifter needs. Check out our video on rebuilding your shifter below: ...

Replacement rubber bushing for repairing any automatic shift arms on any 1967-73 Mercury Cougar or Ford Mustang, and most Fords with automatic floor shift levers. Fits arms with 3/4 inch lower holes for attaching transmission shift rods. Replaces Ford part number C7ZZ-7343 Check out our video on rebuilding your shifter below: ...

Replacement transmission pan filter and pan gasket kit. For the FMX (X Code) transmission. Replaces Ford Part Number: C9ZZ-7A098

New manufactured transmission oil pan for the Ford C6 transmission as found on 1967-73 Cougar and Mustangs, big block and small block engines. Very high quality heavy gauge steel.Replaces Ford part number C6AZ-7A194-A.

These clutch pedals feature an improved design (removable pin) for easier installation. Compatible with existing hanger assembly even in automatics. Replaces Ford Part # D1ZZ-7519-B.

D1ZZ-7519-B Good used pedal but these pedals will no doubt show some wear around the clutch rod holes. Three and four speed pedals are all the same. Mustang is the same too.

These four speed gears have the teeth reversed from the direction of the automatic gears. Made from Nylon. These gears only fit the 4 speed Toploaders. Click here to use our Speedometer Gear Calculator.   Replaces Ford Part # : C2DZ-17271-C 20 Tooth Gear Pictured

These four speed gears have the teeth reversed from the direction of the automatic gears. Made from Nylon. These gears only fit the 4 speed Toploaders. Click here to use our Speedometer Gear Calculator.   Replaces Ford Part # : C2DZ-17271-G 20 Tooth Gear Pictured

These four speed gears have the teeth reversed from the direction of the automatic gears. Made from Nylon. These gears only fit the 4 speed Toploaders. Click here to use our Speedometer Gear Calculator.   Replaces Ford Part # : C2DZ-17271-A 20 Tooth Gear Pictured

These four speed gears have the teeth reversed from the direction of the automatic gears. Made from Nylon. These gears only fit the 4 speed Toploaders. Click here to use our Speedometer Gear Calculator.   Replaces Ford Part # : C2DZ-17271-B 20 Tooth Gear Pictured

These four speed gears have the teeth reversed from the direction of the automatic gears. Made from Nylon. These gears only fit the 4 speed Toploaders. Click here to use our Speedometer Gear Calculator.   Replaces Ford Part # : C2DZ-17271-D 20 Tooth Gear Pictured

New internal speedometer gear fits 4 speed toploader transmissions. Replaces Ford Part #: C5ZZ-17285-A.

Very good quality replacement speedometer cables. 76 inches Replaces Ford Part # : C9ZZ-17260-B

These four speed gears have the teeth reversed from the direction of the automatic gears. Made from Nylon. These gears only fit the 4 speed Toploaders. Click here to use our Speedometer Gear Calculator.   Replaces Ford Part # : C2DZ-17271-G 20 Tooth Gear Pictured

Clutch Fork Pivot for Cougars manufactured after 2/16/1968. Replaces Ford Part #: C8AZ-7522-A.

C8AZ-7515-B Manual transmission clutch fork - 3 and 4 speed, stick shift transmissions. Fork measures 12-5/16 inches long. Alternate number C8AA-7515-B or C8AA-7541-B. Couple of variations of this fork. Most versions will not be stamped. Spring and side holes not needed for Mustang and Cougar applications. Originally for 1968 full sized cars with 289 or 302 engines and manual transmissions. Maybe 6 cylinders, not sure, but vert likely. Cougar 1971 - 1973, 351 Engines. Mustang 1971 - 1973,...

Used original pan removed from a Western parts car, 14 bolt holes. This pan is not available new. These will have some likely have some minor scrapes. These were not painted originally, may have light rust that will clean up. The best available, won't be in stock often. See our Grade B pans for less than half the price. This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of 50% of our...

New manufactured transmission yoke for a T-5 5 speed transmission.

New manufactured transmission slip yoke for either C-4 automatic transmission or small block manual 3 or 4 speed manual transmissions. Ford 1965-1973. 28 splines and 1-1/16" U-joint caps.

Correct for 1971, 1972 and 1973 only. 351-2V and 351-4V engines , including Boss 351 for 1971 - 73. Ford part number D1TZ-6392-A and D1TZ-6392-C. Shipped bare, no hardware or clutch fork.

Reproduction bolts and washers for the manual transmission bell housing on any 1969 - 73 Cougar or Mustang equipped with a 302 / 351 engines and either 3 or 4 speed manual stick shift transmissions. Bell housing to engine block bolts. Fits most all other Ford small block V-8's from 1969-73.

Backup light switch retainer for Hurst shifters as installed on 1970-73 Mercury Cougar, Ford Mustang, and most vintage Ford cars with factory installed Hurst shifters.

Backup light switch for factory installed Hurst competition shifters from 1970-73. This is a Daniel Carpenter reproduction, these are still being made by Hurst in small quantities (see our premium version). It does not include the bracket for holding the switch.Listed in the Motorcraft catalog as SW-943Also fits:CometFairlaneMontegoTorino Check out our video on rebuilding your shifter below: ...

Fits 3 speed or 4 speed manual floor shifts. Sold individually. Check out our video on rebuilding your shifter below:

You will not need to make any modifications to run this leather unit in place of your original rubber boot used on three and four speed manual transmissions.

Reproduction chrome center cap with a black background and chrome Walking Cat logo for the Mercury equipped with the Magnum 500 wheel. The screw on mounting system on this reproduction cap is far superior to the original clip-on center caps. There are other reproduction center caps out there, but they are not nearly as nice. When using center caps on Legendary wheels, you will need these adapter plates. *NOTE* When installing these die cast center caps, keep in mind over tightening will...

Reproduction chrome center cap with a black background and chrome Mercury Man logo for the Mercury equipped with the Magnum 500 wheel. The screw on mounting system on this reproduction cap is far superior to the original clip-on center caps. There are other reproduction center caps out there, but they are not nearly as nice. When using center caps on Legendary wheels, you will need these adapter plates. *NOTE* *NOTE* When installing these die cast center caps, keep in mind over tightening...

Reproduction chrome center cap with a red background and chrome Mercury Man logo for the Mercury equipped with the Magnum 500 wheel. The screw on mounting system on this reproduction cap is far superior to the original clip-on center caps. There are other reproduction center caps out there, but they are not nearly as nice. When using center caps on Legendary wheels, you will need these adapter plates. *NOTE* When installing these die cast center caps, keep in mind over tightening will separate...

Reproduction chrome center cap with a blue background and chrome Mercury Man logo for the Mercury equipped with the Magnum 500 wheel. The screw on mounting system on this reproduction cap is far superior to the original clip-on center caps. There are other reproduction center caps out there, but they are not nearly as nice. When using center caps on Legendary wheels, you will need these adapter plates. *NOTE* When installing these die cast center caps, keep in mind over tightening will...

Set of 4 Chrome center caps with Blue background and chrome walking cat logo. These long awaited caps bolt right onto any Magnum 500 wheel with no modifications. They are 2 3/4" at their widest point and 5/8" tall. Fits the following models with Magnum 500 wheels: 1969 Mercury Cougar 1970 Mercury Cougar These will work with multiple brands / styles of after market wheels as well. Sold individually. When using center caps on Legendary wheels, you will need these adapter plates. *NOTE* Certain...

Set of 4 Chrome center caps with Blue background and chrome Mercury man logo. Better than original! These are held on by a sturdy plate and two screws from the backside which is much better than the original clip-on type. The Magnum 500 wheel was not available on the Mercury line-up until 1974 and it came with a red center cap, star-burst pattern, made from plastic. This brand new to the market cap is a great alternative for the many folks wanting to run an attractive, era correct looking...

The price you see is a temporary price reduction due to overstock. Set of 4 Chrome center caps with black background and chrome Mercury Man logo. Better than original! These are held on by a sturdy plate and two screws from the backside which is much better than the original clip-on type. When using center caps on Legendary wheels, you will need these adapter plates. *NOTE* Certain late model disc brake rotors and aftermarket rotors have a slight clearance issue with the dust cap and...

Set of 4 Chrome center caps with Red background and chrome Walking Cat logo. Better than original! These are held on by a sturdy plate and two screws from the backside which is much better than the original clip-on type. There are other reproductions out there but none are of this quality. When using center caps on Legendary wheels, you will need these adapter plates. *NOTE* Certain late model disc brake rotors and aftermarket rotors have a slight clearance issue with the dust cap and these...

Set of 4 Chrome center caps with red background and chrome Mercury man logo. Better than original! These are held on by a sturdy plate and two screws from the backside which is much better than the original clip-on type. There are other reproductions out there but none are of this quality. When using center caps on Legendary wheels, you will need these adapter plates. *NOTE* Certain late model disc brake rotors and aftermarket rotors have a slight clearance issue with the dust cap and these...

Reproduction chrome center cap with black background and chrome Walking Cat logo. Better than original! These are held on by a sturdy plate and two screws from the backside which is much better than the original clip-on type. There are other reproductions out there, but none are of this quality. When using center caps on Legendary wheels, you will need these adapter plates. *NOTE* Certain late model disc brake rotors and aftermarket rotors have a slight clearance issue with the dust cap...

Chrome center cap with Red background and chrome Ford logo. Better than original! Original look wheel emblem is made from original dies. This plastic cap is painted and detailed in the original colors. This was never used on any year of Cougar but they do look good!  When using center caps on Legendary wheels, you will need these adapter plates. *Note - Certain late model disc brake rotors and aftermarket rotors have a slight clearance issue with the dust cap and these center...

Reproduction chrome center cap with Blue background and chrome walking cat logo. These long awaited caps bolt right onto any Magnum 500 wheel with no modifications. They are 2 3/4" at their widest point and 5/8" tall. These will work with multiple brands / styles of after market wheels as well. Sold individually.  When using center caps on Legendary wheels, you will need these adapter plates. *NOTE* When installing these die cast center caps, keep in mind over tightening will...

Reproduction spinner cap for the Magnum 500 Legendary series wheel. Also works with the Magstar II wheel. Each spinner is die-cast with precision and finished in a show quality chrome plating. The exclusive anti-theft retainer plate keeps them in place and secure. A stamped aluminum Magnum 500 emblem and a "Bullseye" emblem are included so owners can choose which one to personalize their car with.Sold individually ...

This plastic center cap comes with each Legendary Wheel we sell at no cost. We list them for those that may lose or break one. The overall width is 2 1/2" and they are designed for a opening that is 2 3/8 " wide. Sold individually.Check out our video on Legendary Wheels below: ...

Reproduction set of 4 short valve stem assemblies for the Mercury Cougar or Ford Mustang. These new stems will look great on your Magnum, Styled Steel, Shelby, Eliminator or even stamped steel wheel.

Reproduction 15x7" Eliminator wheel with a black center and chrome rim for the Mercury Cougar or Ford Mustang / Torino. The only version of this wheel Mercury ever used on a factory order for a Mercury Cougar was a painted 14x6 with a trim ring used on the 1969 Eliminator. This black 15x7 is a really great custom made wheel that adds flash without deviating too far from the original look. As always, the cap is sold separate. Click here for the hubcap we recommend for this wheel. If you need a...

Reproduction 15x7" Eliminator wheel with a charcoal center and chrome rim for the Mercury Cougar or Ford Mustang / Torino. The only version of this wheel Mercury ever used on a factory order for a Mercury Cougar was a painted 14x6 with a trim ring used on the 1969 Eliminator. This charcoal 15x7 is a really great custom made wheel that adds flash without deviating too far from the original look. As always, the cap is sold separate. Click here for the hubcap we recommend for this wheel. If you...

Reproduction 15x7" Eliminator wheel with a silver center and chrome rim for the Mercury Cougar or Ford Mustang / Torino. The only version of this wheel Mercury ever used on a factory order for a Mercury Cougar was a painted 14x6 with a trim ring used on the 1969 Eliminator. This silver 15x7 is a really great custom made wheel that adds flash without deviating too far from the original look. As always, the cap is sold separate. Click here for the hubcap we recommend for this wheel. If you need...

These off-shore Magnum wheels are supplied to us by Scott Drake. We no longer carry the US made version as the quality was VERY inconsistent. This wheel has a 4 1/4" backspace. We now have Magnum 500 caps that feature the Mercury Logo and the walking cat caps as well. Center caps and lugs are sold separate.   NOTE! These wheels are intended to be balanced with a lugcentric adapter. They will not balance with a traditional cone spacer on the tire spin balancer. Many tire shops do not deal...

These off-shore Magnum wheels are supplied to us by Scott Drake. We no longer carry the US made version as the quality was VERY inconsistent. This wheel has a 4 1/4" backspace. We now have Magnum 500 caps that feature the Mercury Logo and the walking cat caps as well. Center caps and lugs are sold separate.  These are best suited for 1971-73 Cougars. To run a tire larger than a 225/60/15 you may have to modify your fenders and quarters.  NOTE! These wheels are intended to be...

New aluminum 15x8" Magnum 500 wheel for your Mercury Cougar or Ford Mustang. A great way to reduce the un-sprung weight on your Cat or Pony and look great while doing it! This item also includes a center cap, but they are a cheap plastic chromed cap with a blacked out center. We recommend using the adapter plates and Magnum 500 center caps we sell from Scott Drake. Lug nuts sold separately, get them here. ...

New aluminum 17x7" Magnum 500 wheel for your Mercury Cougar or Ford Mustang. A great way to reduce the un-sprung weight on your Cat or Pony and look great while doing it!  This item also includes a center cap, but they are a cheap plastic chromed cap with a blacked out center.  We recommend using the adapter plates and Magnum 500 center caps we sell from Scott Drake. Lug nuts sold separately, get them here. ...

New Legendary Series 15x7" Glossy Finish Magnum 500 wheel for your Mercury Cougar or Ford Mustang. While they look almost identical to the original chromed steel version, these are actually a lighter, better-balanced aluminum alloy with a protective coating. These wheels come with free chromed plastic center caps. The caps have a red Legendary logo but we can include at no cost, a set of black and chrome walking cat decals (click here). Just add it to your cart if you'd like these decals. If...

New Legendary Series 15x7" Satin Finish Magnum 500 wheel for your Mercury Cougar or Ford Mustang. While they look almost identical to the original chromed steel version, these are actually a lighter, better-balanced aluminum alloy with a protective coating. These wheels come with free chromed plastic center caps. The caps have a red Legendary logo but we can include at no cost, a set of black and chrome walking cat decals (click here). Just add it to your cart if you'd like these decals. If...

ETA FOR THIS ITEM IS 12/14/23Reproduction Scott Drake 16x8" Satin Black Magnum 500 wheel for your Mercury Cougar or Ford Mustang. These are the best quality of the three different Magnum 500 wheels you will find on the market today. The chrome is not only brilliant but it holds up great year after year. You may save a few dollars buying the other brands out there but why? We sell these wheels with a 4 1/2" backspace unless you specify otherwise. We now have Magnum 500 caps that feature the...

New Legendary Series 15x8" Glossy Finish Magnum 500 wheel for your Mercury Cougar or Ford Mustang. While they look almost identical to the original chromed steel version, these are actually a lighter, better-balanced aluminum alloy with a protective coating. These wheels come with free chromed plastic center caps. The caps have a red Legendary logo but we can include at no cost, a set of black and chrome walking cat decals (click here). Just add it to your cart if you'd like these decals. If...

New Legendary Series 17x7" Glossy Finish Magnum 500 wheel for your Mercury Cougar or Ford Mustang. While they look almost identical to the original chromed steel version, these are actually a lighter, better-balanced aluminum alloy with a protective coating. These wheels come with free chromed plastic center caps. The caps have a red Legendary logo but we can include at no cost, a set of black and chrome walking cat decals (click here). Just add it to your cart if you'd like these decals. If...

New Legendary Series 17x8" Glossy Finish Magnum 500 wheel for your Mercury Cougar or Ford Mustang. While they look almost identical to the original chromed steel version, these are actually a lighter, better-balanced aluminum alloy with a protective coating. These wheels come with free chromed plastic center caps. The caps have a red Legendary logo but we can include at no cost, a set of black and chrome walking cat decals (click here). Just add it to your cart if you'd like these decals. If...