All Available Parts - 1972 Ford Mustang

Due to the small amount of clearance between the back of your speaker and the door glass when lowered, these and the 60 Watt Kenwood version of this speaker are the only speakers on the market that will replace your worn out originals and fit like OEM without modifications. Rated at 30 watts peak power and 4 ohms.  Nice upgrade over the low wattage originals. Sold as a pair only. Replaces Ford part # C9ZZ-18808-A.   These pictures show what every 69-70 door panel looks like on the...

Due to the small amount of clearance between the back of your speaker and the door glass when lowered, these and their 30 watt little brother are the only speakers on the market that will replace your worn out originals and fit like OEM without modifications. Features Kenwood 60 watt peak power speakers, nice upgrade over the low wattage originals. Sold as a pair.   These pictures show what every 69-70 door panel looks like on the backside.  They are all perforated from from the...

These are identical on the driver and passenger sides.  Two required per car, sold individually. Dimensions: 9" x 3 1/2" Replaces part #: D2ZZ-18978.

Used original driver side (left hand) key lock to latch door lock rod for anu 1971-73 Mercury Cougar or Ford Mustang.Ford part # D1ZZ-6522135-A.

Ford calls this Rod - Door Latch Push Button. This is the driver side manual door locking rod. Side specific to the driver side on any 1971-73  Mercury Cougar and Ford Mustang. Your chromed plastic lock knob threads onto the threaded end, the lower end hooks onto the door latch. Ford part number D1ZZ-6521853-A.

Ford calls this Rod - Door Latch Push Button. This is the passenger side manual door locking rod. Side specific to the driver side on any 1971-73  Mercury Cougar and Ford Mustang. Your chromed plastic lock knob threads onto the threaded end, the lower end hooks onto the door latch. Ford part number D1ZZ-6521852-A.

Good original passenger side door latch rod set. Includes rod for inside lock, outside key lock, and outside door release actuating rod. These are good used parts and are a better quality and value compared to the reproductions. Only fits passenger side doors of 1971-73 Mercury Cougar and Ford Mustang.

Good original driver side door latch rod set. Includes rod for inside lock, outside key lock, and outside door release actuating rod. These are good used parts and are a better quality and value compared to the reproductions. Only fits driver side doors of 1971-73 Mercury Cougar and Ford Mustang.

Protects door panels from the abrasive action of rotating handles. Made from a very hard nylon type material featuring the correct milky white color. Replaces Ford Part Number #C8AZ-6223370-ADiameter 1-1/2"

This handle is a good replacement for the window cranks found on the 1971 - 1972 Cougar both front and back. The originals were 4 1/4" total length and this replacement handle is 4 7/8" long. The important detail on these is the fact that the female portion that attaches to the splined window regulator protrudes from the back 5/16". If you are using our chrome backing plates on your 69 -70, then this is the crank you will need to provide the correct clearance.Used before 10/71,...

Used on both the front and rear of the 1971-1972 Mercury Cougar produced before 10/1/71. The picture above shows the difference between the early version (right) and the later version (left). Plan on purchasing new knobs to go with the bare crank, we have 7 different colors to choose from. See related items. Inquire about a B grade knob if you are looking for something just so that you have a window crank. Ford Part # D0AZ-7630322-A, casting # as seen on the back D1AB-7630322-AWA. ...

Easy to install quality reproduction. Sorry, aqua is not available at this time. Includes crescent spring and correct aluminum pin that features shoulder and locking knurls. Fits 1968-71 cars and about 1 month into 1972. Please see the window crank handles to see the difference between 1968-71 handles and 1972-73 window crank handles. Replaces Ford Part # C8AZ-6223352 *TIP* To install remove your window crank and place knob and crank in the jaws. To protect the knob you will want to place a...

Perfect fit, great reproduction. These plastic discs are found on all 69-70 convertibles on the rear of both decor and xr7 interior levels. We are unclear as to all the "exact" applications on all years and models but one application we have verified is the fronts of 1971 - 73 Cougars equipped with standard interior. The reason the standard interior 71-73 Cougars came with these is that the door panels were very thick on the 71-73 decor / XR7 models and quite thin on the standard models and...

Fits both 8 inch and 9 inch rear ends. Phosphate and oil coated with thread sealer. These are one time only nuts. They should not be reused per Ford. Replaces Ford part #: 371518-S

Retainer or keeper for door hinge pins on all 1968-73 Mercury Cougar and Ford Mustang, plus most all other Ford products with a typical door hinge pin. The factory installed the hinges with the pins driven in from the bottom as viewed with the doors installed. Most restorations install the pins from the top so that gravity holds them in. These retainers allow the pins to be mounted concours correctly. You must use a socket or other tool to install. These fit the door hinge pins with 5/16 inch...

Reproduction window crank used on front doors of cars produced after 10-1-71 with no factory door speakers. Replaces Ford part number D2AZ-7630322-AOriginals have a casting number of D3AB-6523342-AA.

This reproduction power window relay mounts to the front inner apron on the passenger side just behind the starter solenoid. This relay can also be used for 1969-73 power convertible tops, and 1971-73 power seat.Replaces Ford part #: C8AB-14677-A.Will replace D1AZ-14677-A, AND C1AF-14677-A but will not be an exact fit

The High tone is indicated in raised letters located on the perimeter of the horn. The 1971-73 almost uses the same horn and bracket as the 1967-68, but was mounted at a different angle, so if you have a 1971-73 you will need to loosen the screw that holds the horn to the bracket and rotate the horn to the correct position.  These horns are close but not actually correct for a Cougar. 1967-68 Cougars used part number C7WF-13802-B Lo / C7WF-13801-B Hi and 1971-73 used D0DF-13802-A Lo /...

Reproduction 384543-S8 Power steering pump adjusting spacer for use without air conditioning. For most 1970 - 1973 Mercury Cougar or Ford Mustang with 351C engines. Spacer dimensions: 7/16" I.D. and 1/2" thick.*Note 1970 and later cars with 302 or 351W engines use a 3/4 inch spacer.

Used water pump pulley used on 1970-73 Mercury Cougar and Ford Mustang with 351 engines and air conditioning. This pulley is 5-15/16 inches in diameter. Pulley stamped C9OE-8509-F.

Single sheave pulley 6-61/64 inches in diameter. This pulley is designed to run on the inner most belt plane next to the water pump. When measured from the front of the water pump hub (or inside of the pulley) to the center line of the belt sheave the measurement is 2-5/16 inches. Applications:1970 Boss 302 Eliminators with power steering**1970 351 with power steering**1971 - 1973 351 engines with power steering or with idler pulley without air conditioning* Ford casting number D1AE-8509-BA....

Used pair of lower radiator brackets as taken from any 1971-73 Mercury Cougar or Ford Mustang. Additionally these will also fit 1970-71 Ford Torino / Fairlane and 1970-71 Mercury Montego / Cyclone. Should be for all engines. 250 6 cylinder, 302, 351, and 429. Right and left are different, plan on purchasing the insulating rubbers, they may not always be included. Ford part numbers D0OB-8052 or D0OZ-8052-A for passenger side, D0OB-8B381 or D0OZ-8052-B for the driver side. Check out our video on...

Concours for 1970 351C-2V and 351C-4V with correct ink stamped Ford script, 17 1/2" long including the 90 degree bend. Connects PCV valve to carburetor spacer plate. Other parts houses list this as a 71-73 but the 71-72 is 25" long (so it can reach to the front of the driver side valve cover) on both the 2V and 4v 351 Cleveland and this hose will not reach. This will work for the 1973 Q-code 351C-4V as the 73 mates to a metal tube and is only 11".This hose was originally installed from the...

D1OZ-6A664-B Original used hose that connects the valve cover mounted PCV valve and the carburetor spacer plate on 1971 through 1972 Mercury Cougar and Ford Mustang 351C or Cleveland engines only. Used hoses will have faded striping (if present), and clamp impressions. Very often the rubber will be hard and showing some degree of stress cracks. *Note - Excludes all 1969-71 351W or Windsor engines, 1970 351C or Cleveland, and 1973 351C engines. *Note - These molded and contoured hoses were...

For 351 Cleveland or Windsor when equipped with the "Flame Arrestor" PCV Valve. Also fits multiple applications with 1" hole in steel valve covers in which the PCV valve presses into. Inside diameter is 23/32". Replaces Ford Part #: C8SZ-6892, C8SZ-6A892-A or 381898S.

Replaces Ford part #C7AZ-6892. For round hole with two notches, aluminum or steel valve covers.

Replaces grommet in chrome oil cap with PCV valve. Inside diameter is 37/64". Replaces Ford part #: C8AZ-6892 or C8AZ-6A892-A.

A needed part for giving your car a tune-up. PCV Valve fits all years; 289, 302, 351, 390, and 428 CID; V8. *Note - Not technically correct for 390-4V or 428CJ, those originally used a PCV valve with a threaded top, and the 90° elbow - part number C7OZ-6A706-A.

Clips or clamps for attaching the 3/8" hard fuel lines to the body of any 1968-73 Mercury Cougar or Ford Mustang. Clips only, save your attaching body bolts. Sold in packages of 4 clips as shown. Will work on 1967 cars if you change to 3/8 lines. 1971-73 Cougar owners can use item 27565 attaching bolts, they are the same as the fuel tank mounting bolts. See related items. Replaces Ford 354663-S8

New flat nut, these attach both the shifter seal and shifter dial to the under side of the automatic shifter bezel. Check out our video on rebuilding your shifter below: ...

Rechromed 1967 deluxe shifter button. Unique to the deluxe faux leather wrapped T handle shifter starting in 1967. One year only design, this one has a convex button for you thumb. Starting in 1968 the button was more rounded to comply with the added safety features mandated in 1968. Core deposit is required, fully refundable with returned 1967 deluxe button. Ford part number C7ZZ-7C488-B. Check out our video on rebuilding your shifter below: ...

Reproduction Firewall Insulation Pad Clip Kit for the 1967 - 1973 Mercury Cougar / Ford Mustang

Reproduction thin firewall insulation pad with clips for the Mercury Cougar or Ford Mustang. This unit will fit both the A/C and non A/C Cougar or Mustang.

Screw for attaching steering column plate to floor board. Usually 4 are needed and go through the carpet and into the toe board. Correct finish and style of AMK bolt. Length 1 3/16"#14 Threads

Used driver side interior kick panel for any 1971-73 Mercury Cougar. Ford calls this item a "Panel - Cowl Trim". These came in a variety of different colors, please indicate a desired color in the notes. Plan on painting the panel with a quality vinyl paint such as those made by SEM for a quality installation. These are used, and will likely show some scuffing from hard shoes.  Ford part number D1WB-6502344, D2WB-6502344, D3WB-6502344. ...

Used driver side interior kick panel for any 1971-73 Mercury Cougar. Ford calls this item a "Panel - Cowl Trim". These came in a variety of different colors, please indicate a desired color in the notes. Plan on painting the panel with a quality vinyl paint such as those made by SEM for a quality installation. These are used, and will likely show some scuffing from hard shoes.  Ford part numbers D1WB-6502345, D2WB-6502345, D3WB-6502345.

Good used console clock surround bezel with no cracks, or peeling chrome. Engineering number on the backside reads D1ZB-15017-AA

Used metal dash support brace for all 1971-73 Mercury Cougar and Ford Mustangs. Fastens to the lower flange of the metal dash panel and attaches to the inner cowl, 10 inches long. Replaces Ford part numbers D1ZB-6504672-A.

Replacement throttle pedal spring for your 71 - 73 Cougar or Mustang. Easy to replace, keeps correct tension on your gas pedal.

Finally, a reproduction radio knob set for your 1971-73 Mercury Cougar or Ford Mustang! These little units are very hard to find in NOS form or good used condition with flawless chrome. Most knobs are peeling bad enough to cut you if you are not being cautious. It's often little detail pieces like these that separate first and second place at car shows.Replaces Ford part #'s D1ZZ-18817-A for the outer (tuner / volume) knob, Ford casting # D1ZA-18822-AA for the outer (tuner / volume) knob....

This kit is similar to the original type mounted in every drivers side door. These OEM style Riv-Nuts will be a challenge to install unless you have the special tool. Almost every body shop will have this rivet gun type of tool but here are a couple of ways to tackle the installation without the correct tool. Hole size is 1/4". Replaces Ford Part #: C7AZ-17696. Check out our video below for more info on mirror installation: Still have riv-nut questions? Here are riv-nut answers! ...

New mirror glass, for the passenger side on practically any 1969-73 Ford with painted sport mirrors. This is the convex style of mirror, think "Objects in mirror are closer than they appear". Nice fit, exact shape of originals. Dimensions: 4 3/8 x 2 7/8 Do you have questions about installing a passenger side mirror or using Riv-Nuts? Have more questions about installing a passenger side mirror or using Riv-Nuts? Got a mirror lens that flops around in your Sport Mirror every time you hit a tiny...

Pair of reproduction brackets and rods for the sun visors in the Mercury Cougar or Ford Mustang. *NOTE* These units will also work for the 1971-73 Ford Mustang fastback (sport roof).

For fixed steering wheel. Special molded rubber sleeve that holds the bearing in place. Exact reproduction. Replaces Ford part # D1AZ-3518 or E2AZ-3518

Used plunger spring used in the bale of the tilt / tilt away steering column found in the Mercury Cougar or Ford Mustang. Small plunger spring for 1967-69 tilt columns. Maintains pressure on the heavy wire tilt release bale. This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of 50% of our web price for parts delivered in hand or by carrier to our Brooks, Oregon location. If you're not...

Replacement filter for FMX transmissions. Fits all Ford FMX transmissions for any 1969-73 Mercury Cougar or Ford Mustang with that X code FMX transmission. 

Used retaining clip for the adjustment bar in the tilt / tilt away steering column in the Mercury Cougar or Ford Mustang. Two required per car, used to hold the tilt position adjustment bar in place.  * While not technically correct, this also will work for 1970 - 1974 Cougar/ Mustang tilt columns. SOLD INDIVIDUALLY*NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our...

This item holds the release bale to the upper knuckle. It is different than the 67 - 69 clip although both can be used. *NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year.

This linkage fits between the gear at the bottom of the key lock and rod that goes to the ignition switch on the tilt column.*NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year.

1972 working, used ignition switch. This is only the electrical side, the mechanical key and lock section is not included. See appropriate shop manual for proper alignment and installation. Tested and working ignition switch. Follow the instruction in your shop manual for installation and adjustment. Original Ford part number was either D2AZ-11572-A or D1AZ-11572-B. Application also for 1971 Lincoln MK III and 1971 Ford Thunderbird. Ford had a service replacement ignition switch with a part...

Used pivot pin for the Mercury Cougar or Ford Mustang / Thunderbird equipped with a tilt / tilt away column. This is a pressed pin with a flange and five are required per car. This pin is internally threaded with a # 8-32 thread. Ford part # D0AZ-3D739-A. *NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year. ...

This is the part of the tilt switch that the turn signal wand screws into. This part is always included when you purchase a new turn signal switch. 1967-69 mechanism has two springs on either side, the 1970-73 mechanism uses just one spring. There is an active thread on the Classic Cougar Community Forum discussing tilt columns and trouble shooting. *NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many...

Tilt release lever or bale. *NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year.

Used locking pawl for the 1970 - 1979 Mercury Cougar or Ford Mustang that is equipped with a factory tilt steering column. This unit works in conjunction with a pin and is responsible for locking the tilt column in place. In many cases, the pin tends to move out of place and break or chip the teeth of the locking pawl. We have found that 3 of 4 tilt columns that we have disassembled have locking pawls with broken or chipped teeth. These units will be mint with no broken or chipped teeth....

Used lower steering column knuckle for the Mercury Cougar or Ford Mustang. This unit is used in the 1970-73 tilt only column and can be the issue when you have a sloppy feeling tilt column. The hard steel pin will often waller out the soft cast metal and cause play in the column. Ford part # D1AZ-3D651-A, casting number D1AA-3D651-AA or D0AA-3508-F. *NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent...

Used upper steering column knuckle for the Mercury Cougar or Ford Mustang. This unit is used in the 1970-73 tilt only column. Ford casting # D1AZ-3511-AWA.*NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year.

Used lock insert for the steering column in the Mercury Cougar or Ford Mustang equipped with the tilt steering column.*NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year.

Used lock insert for the steering column in the Mercury Cougar or Ford Mustang equipped with the fixed steering column.*NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year.

1967-68 XR7 over head console pad clip. Two needed per car. Sold individually # C3AB-63519A16

NOTE: Some modification required to fit Cougars! These are actually 69-70 Mustang wheel lip mouldings, which have a different shape / contour. However, with a bit of massaging they can be made to fit the 71 - 73 Cougar. They are the closest alternative we have found that fits and looks reasonably good for much less than restored originals. Check out our video below, showing how easy it is to install these mouldings on a Cougar ...

Restored four piece aluminum rear window moulding / trim set correctly restored with an anodized and a bright dip finish and polished to a very high luster.Ford part #s D1ZZ-6542405-A, D1ZZ-6542404-A, D1ZZ-6542430-A, D1ZZ-6542431-A.

Good used four piece aluminum rear window moulding / trim set with some dings and or minor scratches. Ready to install on your Cougar as is, or polish them to be installed on a daily driver. These original FoMoCo mouldings are far superior to the off shore reproductions that do not fit well and have an incorrect color to them. Ford part #s D1ZZ-6542405-A driver side (left hand) lower, D1ZZ-6542404-A passenger side (right hand) lower, D1ZZ-6542430-A passenger side upper, and D1ZZ-6542431-A...

Our used passenger (right hand) side upper rear aluminum window mouldings / trim will have light scratches and minor dings. These are suitable for restoration or for a lower quality daily driver. We will not send you kinked or gouged trim as it is not feasible to restore heavily damaged trim. Ford part # D1ZZ-6542430-A.

Our used passenger (right hand) side lower rear aluminum window mouldings / trim will have light scratches and minor dings. These are suitable for restoration or for a lower quality daily driver. We will not send you kinked or gouged trim as it is not feasible to restore heavily damaged trim. Ford part # D1ZZ-6542404-A.

Our used driver (left hand) upper rear aluminum window mouldings / trim will have light scratches and minor dings. These are suitable for restoration or for a lower quality daily driver. We will not send you kinked or gouged trim as it is not feasible to restore heavily damaged trim. Ford part # D1ZZ-6542430-A. ...

Our used driver (left hand) lower rear aluminum window mouldings / trim will have light scratches and minor dings. These are suitable for restoration or for a lower quality daily driver. We will not send you kinked or gouged trim as it is not feasible to restore heavily damaged trim. Ford part # D1ZZ-6542430-A.

Our core passenger (right hand) upper rear aluminum window mouldings / trim will have some scratches and dings and are suitable for restoration. We will not send you kinked or gouged trim as it is not feasible to restore heavily damaged trim.Ford part # D1ZZ-6542430-A.

Our core driver (left hand) upper rear aluminum window mouldings / trim will have some scratches and dings and are suitable for restoration. We will not send you kinked or gouged trim as it is not feasible to restore heavily damaged trim.Ford part # D1ZZ-6542431-A.

Our core passenger (right hand) lower rear aluminum window mouldings / trim will have some scratches and dings and are suitable for restoration. We will not send you kinked or gouged trim as it is not feasible to restore heavily damaged trim.Ford part # D1ZZ-6542404-A.

Our core driver (left hand) lower rear aluminum window mouldings / trim will have some scratches and dings and are suitable for restoration. We will not send you kinked or gouged trim as it is not feasible to restore heavily damaged trim.Ford part # D1ZZ-6542405-A.

Our core aluminum rear window mouldings / trim will have scratches and dings and are suitable for restoration. This kit consists of one driver side (left hand) upper, one passenger side (right hand) upper, one driver side lower, and one passenger side lower core window moulding / trim. These original FoMoCo mouldings are far superior to the off shore reproductions that do not fit well and have an incorrect color to them. We will not send you kinked or gouged trim as it is not feasible to...

Restored pair of windshield mouldings / trim for the Mercury Cougar or Ford Mustang coupe. These units have been restored using the correct bright dip anodize and will look better than NOS.  Ford part # driver side D1ZZ-6503145-A, passenger side D1ZZ-6503144-A.

Used pair of windshield mouldings / trim for the Mercury Cougar or Ford Mustang coupe. The bright dip anodize has worn off of these and they may have some very fine scratches, but they will not be dented or have any heavy scratching. Suitable for your daily driver or for restoration.Ford part # driver side D1ZZ-6503145-A, passenger side D1ZZ-6503144-A.

Core pair of windshield mouldings / trim for the Mercury Cougar or Ford Mustang coupe. These units may have some dings, scratches and will be dull. A cheap and easy fix for your cat or pony that may have missing windshield trim.  Ford part # driver side D1ZZ-6503145-A, passenger side D1ZZ-6503144-A.

Restored passenger side (right hand) windshield moulding / trim for the Mercury Cougar or Ford Mustang coupe. This unit has been restored using the correct bright dip anodize and will look better than NOS.  Ford part # D1ZZ-6503144-A.

Used passenger side (right hand) windshield moulding / trim for the Mercury Cougar or Ford Mustang coupe. The bright dip anodize has worn off of this unit and it may have some very fine scratches, but will not be dented or have any heavy scratching. Suitable for your daily driver or for restoration.  Ford part # D1ZZ-6503144-A.

Core passenger side (right hand) windshield moulding / trim for the Mercury Cougar or Ford Mustang coupe. This unit may have some dings, scratches and will be dull. A cheap and easy fix for your cat or pony that may have missing windshield trim.  Ford part # D1ZZ-6503144-A.

Core driver side (left hand) windshield moulding / trim for the Mercury Cougar or Ford Mustang coupe. This unit may have some dings, scratches and will be dull. A cheap and easy fix for your cat or pony that may have missing windshield trim. Ford part # D1ZZ-6503145-A. 

Used driver side (left hand) windshield moulding / trim for the Mercury Cougar or Ford Mustang coupe. The bright dip anodize has worn off of this unit and it may have some very fine scratches, but will not be dented or have any heavy scratching. Suitable for your daily driver or for restoration.  Ford part # D1ZZ-6503145-A.

Restored driver side (left hand) windshield moulding / trim for the Mercury Cougar or Ford Mustang coupe. This unit has been restored using the correct bright dip anodize and will look better than NOS.Ford part # D1ZZ-6503145-A.

Stainless trim that affixes to the leading edge of the quarter window on coupe or convertible. Does not come with weather strip.

Reproduction four piece aluminum rear window moulding / trim set for the 71 - 73 Cougar or Mustang. Customers have mentioned that these are very hard to install on the Cougar. Ford part #s D1ZZ-6542405-A, D1ZZ-6542404-A, D1ZZ-6542430-A, D1ZZ-6542431-A.

Reproduction pair of windshield mouldings / trim for the Mercury Cougar or Ford Mustang coupe. Replaces Ford part #'s driver side D1ZZ-6503145-A, passenger side D1ZZ-6503144-A.

Stainless trim that affixes to the leading edge of the quarter window on coupe or convertible.

Seatbelt warning light relay for most Ford Lincoln and Mercury cars. This one has a D2AB-10B924-AA part number, but should be the same as the C7AB-10B924-A relay, they are identical except for the part number and the inclusion of "Motorcraft". This is a timed relay that allows several seconds of illumination to your seat belt warning light.These are tested and guaranteed to work.

Used in 1971-73 Mercury Cougars and Ford Mustang for the stop lamps, located under the dash on a panel next to the fuse block.15amp circuit breaker. It is 1.25" x 13/16" and has a single green dot. Box is marked FASCO, 15AMP 12V, and made in the U.S.A. Integrated mounting tab for this application. Ford part number D1MY-14526-A. *NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the...

Tested and working relay for the 'headlights - on' reminder. Relay with mounting tab for 1971-73 Mercury Cougar and Ford Mustang. This relay controls a buzzer as a reminder to turn off the headlights or remove the key, when the door is opened.Replaces Ford part number D1AB-10C838-A or D1AZ-10C838-A.

This direct replacement is the 2-1/4 inch H pipe only and is for any 1971-73 Mercury Cougar or Ford Mustang with stock cast iron exhaust manifolds. These units are manufactured right here in the good old USA from 2-1/4 inch aluminized pipes and made from an original 1971 Cougar and Mustang with either the H, M, or Q code 351C engine. We also sell OEM style dual exhaust systems that include the H pipe, mufflers, and tail pipes.*NOTE* Will not fit 351 Windsor, 1970 351 Cleveland engines. Please...

This direct replacement is the 2 inch Y pipe only with 2-1/4 intermediate pipe outlets and is for any 1971-73 Mercury Cougar or Ford Mustang with stock cast iron exhaust manifolds. These units are manufactured right here in the good old USA from 2 inch aluminized pipes and made from an original 1971 Cougar and Mustang with the 351C 2V engine. We also sell OEM style dual exhaust systems that include the H pipe, mufflers, and tail pipes.*NOTE* Will not fit 1970 351 Cleveland engines. Please...

Now in grey with no zipper, our comfy WCCC hoodie features bold new walking cat graphics on front and back. Perfect for staying warm in the garage, or out and about with your Cougar! This sweatshirt is made with soft, mid weight fleece and generous fit for comfort. Features a jersey lined hood, heavy gauge drawcord with metal eyelets and 1x1 ribbing at cuffs and waistband. 8.5 oz fleece80% cotton 20% polyester blend100% cotton 20 singles face yarnSplit stitch double needle sewing on all...

Now in black with no zipper, our comfy WCCC hoodie features bold new walking cat graphics on front and back. Perfect for staying warm in the garage, or out and about with your Cougar! This sweatshirt is made with soft, mid weight fleece and generous fit for comfort. Features a jersey lined hood, heavy gauge drawcord with metal eyelets and 1x1 ribbing at cuffs and waistband. 8.5 oz fleece80% cotton 20% polyester blend100% cotton 20 singles face yarnSplit stitch double needle sewing on all...

Housing overall width - 55-3/4 inches flange to flange. Spring perches are 43 inches apart on center. Bare housing with proper axle pad spacing for all 1971-1973 Cougars. Over-sized shipping length.Axles needed: Passenger side - 32 inches long, Driver side 28 inches long.

Right side axle, 28 spline 31-7/8 inch length. Ships with used bearing, bearing retainer plate, and 5 pressed in wheel studs. *Note 429 CJ equipped Cougars came with heavy duty 31 splined axles.

Left side axle, 28 spline 27-13/16 inch length. Ships with used bearing, bearing retainer plate, and 5 pressed in wheel studs. *Note 429 CJ equipped Cougars came with heavy duty 31 splined axles.

Since we always claim to have parts nobody else does... This welds to the bottom side of the car just above the differential. When the rear suspension bottoms out, this is the plate the rubber snubber / bumper (mounted on the front on top of the dif.) makes contact with.

Also called a pumpkin, 2.75:1 open ratio. Check your door tag under "Axle". 1968 code 1 1969-73 code 2

Mounts over rear axle ends into the body/frame, two required per car, this is the more pointed Christmas tree shaped version.Ford part # C6AZ-4730

D0OZ-4204-9A300 1968-1973 9 Inch Third Member - Used Also called a pumpkin, 3.00:1 open ratio. These 3rd members will have the fill plug. Check your door tag under "Axle".

NOTE! When we ship a rear end, we will remove the third member and ship it in a separate box. Some assembly will be required. Housing overall width - 55-3/4 inches flange to flange. Spring perches are 43 inches apart on center. Overall width measured from faces of axles, not the tips. All 1971-73 have the same overall width of 61 inches.  Rear axle assembly - Housing, Axles, brake backing plates, and third member. As removed from a 1971-73 West Coast Cougar organ donor car. We...

#373820-S Copper washer for attaching the 8 inch or 9 inch third members to the axle housings. Steel washers will leak, made from copper which is a soft metal and seals under the attaching nuts. Copper washers like the OEM Ford installed washers. Takes 10 washers total for both 8 and 9 inch rear ends. *Tip - It is a good idea to inspect or replace your old washers, many times they have tool marks from the housing or nuts that cause small troublesome leaks.