All Available Parts - 1973 Ford Mustang

Used clutch pedal return spring with two original nylon bushings. Ford Part #: C8OZ-7534-B.

Equalizer bar or "Z" bar for 351 and 429CJ engines with a manual transmission. Used after 4-30-1971. Both 3 and 4 speed manual transmissions. This is a used part and it will most likely show some wear form previous use. Ford part # D1ZZ-7528-C.*NOTE* Before 4-30-1971, use Ford part # D1ZZ-7528-A.

Fits 1968 (mid year change) through 1976 Cougar and Ford forks - All engines.Includes:1 Spring Clip2 RivetsReplaces Ford Part #: C8AZ-7B516-A.

Stainless Clutch Pedal Pad Trim. Replaces Ford Part #: C9ZZ-7B544-A.

New Old Stock Ford flywheel. 11 inch clutch, 164 tooth ring gear,12-3/8 inch bolt circle for clutch pressure plate. Cast iron with C5AE-A and C7TE-A. New, never installed Ford manual transmission flywheel. Fits 351W, 351C, and 351CJ. Ring fear installed, factory fresh.

Ford small block engines and with a 3 or 4 speed manual transmission. Fits only the larger 164 tooth flywheel.

New internal speedometer gear fits 4 speed toploader transmissions. The largest number of 4 speed toploaders came stock with this gear. Replaces Ford Part #: C4DZ-17285-A.

Original equipment 4 speed top loader transmission from a 1972 or 1973 Mercury Cougar with engine code Q - 351-4V only. This is a late transmission and was used starting 12-1-1971. Transmission code 5 on the door tag, this would be a wide ratio 4 speed transmission with a 2.78 ratio first gear.Ford part # D2ZZ-7003-H, casting # RUG-BJ1. Percentages of Cougars equipped with a manual transmission by year1967 = 18.5%1968 = 13.2%1969 = 10.5%1970 = 7.8%1971 = 2.8%1972 = 1.5%1973 = 0.7%Total for...

D2ZZ-7210-A Round chromed �Hurst� labeled shifter for all 1972 and 1973 Mercury Cougar and Ford Mustangs with factory installed 4 speed transmissions. Tough part to find loose, most will be attached to the correct vintage Hurst Competition shifter mechanism. These shifters will not come with the round shifter ball knob. Check out our video on rebuilding your shifter below: ...

Hurst built 4 speed manual shift control assembly for any 1972 - 1973 Mercury Cougar or Ford Mustang. This will have the round Hurst shifter lever. Includes shifter mechanism, shift rods, and shift lever. All in used condition.Ford part # D2ZZ-7400-Assembly Check out our video on rebuilding your shifter below: ...

New manufactured Tremec T-5z World Class Transmission. Same transmission as installed in Fox Body Mustangs. This is the common transmission for conversions that does not involve extensive modifications to 1967-73 Mercury Cougar or Ford Mustang. Small block Ford V-8 engines only, 289 / 302 / 351W and 351C. Brand new transmission, no core required. 1 year warranty, with recommended synthetic ATF. Flush and fill after first 500 miles, 30,000 miles there after. Bare transmission as shown, no...

Fits all applications for both automatic and manual transmissions, big block and small block. Will also work with your Tremac / T-5. Replaces Ford part # C4DZ-6068-A.

This is a modern upgrade to your manual transmission cars. It replaces the bushing that is in the crank shaft. Supports the tip of the input shaft of the transmission. Quality part with roller bearings on the inside, fits small block only.Replaces Ford Part #: C7AZ-7600-A.

Replacement rubber material pan gasket for all 1965-73 C4 Ford transmissions. 

Shift kit for the FMX transmission valve body for all 1969-72 and 1969-72 Mercury and Ford. This is a standard shift rebuilding kit for your stock valve body.* Note - 1973 has a different shift kit, see related items.

Replacement seal with boot for all 1969-73 FMX and 1967-73 C6 transmissions. Tail shaft and slip yoke seal. 

Tall style filter for C4 transmissions.  Fits all Ford C4 transmissions for any 1966-73 Mercury Cougar or Ford Mustang with that W code C-4 transmission. This is designated as the 'tall' filter, introduced in 1965. I guess that Ford installed a deeper pan in 1965? Solid metal construction with filter inside.

Set of 6 new correct bolts for attaching the FMX transmission to 351 engines. Fits all 1967-73 Mercury Cougar and 1967-73 Ford and Mustang with transmission code X, or FMX automatic transmissions. Quality fasteners from AMK.

Basic FMX transmission rebuild kit. Kit includes gaskets, seals, bands, filter, modulator, everything as shown. Fits all Ford FMX transmissions for any 1969-73 Mercury Cougar or Ford Mustang with that X code FMX transmission. Quality kit, same as supplied to professional shops. 

O Ring gasket for all automatic transmission dip stick tubes. Replacement gasket for C4, C6, and FMX trans dip stick tubes 1967-73 Mercury Cougar and Ford and Mustang.

Brand new flex plate for all 1969 - 73 Mercury Cougar and Ford Mustang with 302 / 351W / 351C engines, and C4, C6, or FMX transmissions. Comes complete with new starter ring gear installed as shown.*Note - Fits common torque converter bolt pattern of 11.40 inches. In 1972 there was a unique C6 torque converter with a 9.50 inch bolt pattern. 

Original dipstick or in Ford speak "Indicator - Oil Level" for FMX automatic transmissions. Application for 1972 - 1973 Mercury Cougar and Ford Mustang with 351 and FMX automatic transmissions, code "X" on your door data plate. Sometime during 1972 Ford changed to C9AP-7A020-C. Same dip stick, but with a longer handle.Ford casting # C9AP-7A020-C.

This very rare part is unique to the 1972 - 1973 351-4V / 351CJ with C6. We have determined that this part only fits Mercury Cougar and Ford Mustang. Torino and mid sized Ford/Mercury use a different numbered part. Marked D2ZP-AB. Ford Part #: D2ZZ-7A256-A. Check out our video on rebuilding your shifter below: ...

Original dipstick tube, originally painted yellow and is approximately 18-3/64" inches long. Application 1971 - early 1973. Mercury Cougar or Ford Mustang with C6 automatic transmissions, code "U" on your door data plate. For any 351 or 429CJ engine. Ford master part number D1ZZ-7A228-A. *NOTE* Only used until 11-1-1972.

Original dipstick or in Ford speak "Indicator - Oil Level" for C6 automatic transmissions. Application for 1970 Mercury Cougar and Ford Mustang with 351 engines and C6 automatic transmissions, code "U" on your door data plate. Ford part # D3ZZ-7A020-A, Ford part # D3ZP-7A020-A.

Original dipstick tube, painted yellow and is approximately 17-23/32" inches long. Application 1973 Mercury Cougar or Ford Mustang with C6 automatic transmissions, code "U" on your door data plate. Ford master part number D3ZZ-7A228-A. *NOTE* Only used after 11-1-1972.

D1ZZ-6523312-A Bracket that attaches the end of the power window motor to the door on the passenger side of 1971-73 Cougar and Mustangs with power windows.

D1ZZ-6523313-A Bracket that attaches the end of the power window motor to the door on the driver side of 1971-73 Cougar and Mustangs with power windows.

1971 - 1973 Mercury Cougar and Ford Mustang coupe / convertible Grade A factory tinted glass for the driver side door

D1ZZ-6523258-A Black plastic bolt-in door glass bushing. Used on 1970 bolt in door glass and 1971-73 door and quarter glass. White was used in early 1970, and black from 1970-73. There was some overlap in 1970. ...

1971 - 1973 Mercury Cougar and Ford Mustang coupe / convertible Grade A factory tinted glass for the driver side door

Made by Trico who made them originally for Ford. Replaces Ford part #: D1ZZ-17528-A. Sold individually

Used driver side (left hand) grade "B" clear door glass for the Mercury Cougar or Ford Mustang coupe or convertible equipped with power windows. It will not have the faint green tint like the SUN-X factory tinted glass. Good used door glass with minor vertical scratches due to hardened belt line rubber seal and debris caught within the belt line seal. Ford part # D1ZZ-6521411-C.  *NOTE* Air conditioning cars were supposed to have SUN-X tinted glass. Look for the SUN-X logo in the bottom...

Used passenger side (right hand) grade "B" clear door glass for the Mercury Cougar or Ford Mustang coupe or convertible equipped with power windows. This unit will not have the faint green tint like the SUN-X factory tinted glass. Good used door glass with minor vertical scratches due to hardened belt line rubber seal and debris caught within the belt line seal. Ford part # D1ZZ-6521410-C.  *NOTE* Air conditioning cars were supposed to have SUN-X tinted glass. Look for the SUN-X logo in...

Used driver side (left hand) grade "A" clear door glass for the Mercury Cougar or Ford Mustang coupe or convertible equipped with power windows. It will not have the faint green tint like the SUN-X factory tinted glass. Very good used door glass with no deep scratches (multiple faint scratches and water spots often will be present). Not perfect but the best you could expect to find from a 50 year old plus parts car and will of course be a better fit than repro.Ford part # D1ZZ-6521411-C....

Used driver side (left hand) grade "A" clear door glass for the Mercury Cougar or Ford Mustang coupe or convertible equipped with manually operated windows. It will not have the faint green tint like the SUN-X factory tinted glass. Very good used door glass with no deep scratches (multiple faint scratches and water spots often will be present). Not perfect but the best you could expect to find from a 50 year old plus parts car and will of course be a better fit than repro.Ford part #...

Used passenger side (right hand) grade "A" clear door glass for the Mercury Cougar or Ford Mustang coupe or convertible equipped with manually operated windows. This unit will not have the faint green tint like the SUN-X factory tinted glass. Very good used door glass with no deep scratches (multiple faint scratches and water spots often will be present). Not perfect but the best you could expect to find from a 50 year old plus parts car and will of course be a better fit than repro.Ford part...

Very good used door glass with no deep scratches (multiple faint scratches and water spots often will be present). Not perfect but the best you could expect to find from a 50 year old plus parts car and will of course be a better fit than repro. For those wanting Grade "A" glass, we recommend calling us so we can discuss with you the glass that we have available.Need a little help identifying some of the markings on your glass? Check out the Guide to Original Date Coded Glass - Mustang, Boss,...

Stainless steel throttle pedal surround trim. Self attaching to part number D1ZZ-9735-B. This used part may have some wear, but will not have broken tabs. Fine steel wool really shines these up. It appears that this trim may not have been used all the way through 1973. Ford probably eliminated it as a cost saving measure.

Bracket mounts to top of stock cast iron Cleveland intake manifold, holding the throttle cable. All 351C engines, 351-2V and 351-4V. Fits any 1972-73 Mercury Cougar or Ford Mustang with original H or Q code 351C engines. The earlier bracket found on the 1971-72 cars will also work and is stamped slightly differently.Replaces Ford part number D2AZ-9728-A.

Used in-tank, fuel sending unit without the low fuel option. Tested and cleaned units for all 1971-73 Mercury Standard model Cougars and all Ford Mustangs with 22 gallon fuel tanks. This is an original 1971-73 fuel sending unit with two electrical prongs. Ford casting number D1ZF-9275-AB. This unit comes with a new 3/8 inch filter, brass float, and sending unit gasket. *Note - Not compatible with Mercury Cougar XR7 models with low fuel warning light. The sending units with low fuel have 3...

Quality U.S.A. made hose with concours repeating GAS markings. Also include OEM mounting hardware. Replaces Ford Part #: C7ZZ-9327-A. Check out our video on replacing the fuel system on a '68 Cougar! ...

Basic kit for rebuilding your Ford Autolite or Motorcraft spread bore 4300D or 4 barrel carburetor with large secondary venturis. Covers all factory 4 barrel carburetors for all 1972-73 Mercury Cougar and Ford Mustang with Autolite or Motorcraft 4300 carburetors. Excludes earlier square bore 4300 carburetors.

D3ZE-9A589-AB Factory 1973 Autolite / Motorcraft 4300 Carburetor spacer plate with attached EGR valve. The exhaust gas recirculation valves started showing up on American cars in 1973. There will be almost always some erosion from the heated exhaust gases. This is for use with the Motorcraft 4300 carburetor with Ford part number D3ZF-MA.

1973 351-2V Motorcraft 2100 Carburetor, automatic transmissions - both FMX and C6. D3AF-DC stamped on the carburetor base, spreadbore design of 351 cfm. Rebuildable core carburetor with proper numbers, we don't always have the factory Ford Autolite tag that was affixed to the top. *Trivia - all 1973 Cougars with a H code 351-2V engine were automatics, no manual transmissions built.

1973 351CJ-4V Motorcraft 4300D Carburetor, automatic C6 transmission- 50 states. D3ZF-MA stamped on the carburetor base, spreadbore design of 715 cfm. Rebuildable core carburetor with proper numbers, we don't always have the factory Ford Autolite tag that was affixed to the top.

1973 351CJ-4V Motorcraft 4300D Carburetor, 4 speed manual transmissions- 50 states. D3ZF-LA stamped on the carburetor base, spread-bore design of 715 cfm. Rebuildable core carburetor with proper numbers, we don't always have the factory Ford Autolite tag that was affixed to the top. This unit was actually rebuilt and never used.

These stainless steel tubes are made to exact O.E.M. standards and specifications. All choke tubes have the proper fiberglass insulation, fittings, rubber hose, and S-clip.

These steel tubes made to exact O.E.M. standards and specifications.

Reproduction disc brake hose bolt for any 1968-73 Mercury Cougar and generally all other Ford cars with factory disc brakes. Special hollow bolt with cross drilled hole. Attaches the high pressure hose to the caliper.

Reproduction of the plastic square hood insulation clips. 11 used on most vehicles. Sold individually.

Dash pad attaching nut 8-32 threads original zinc plate and dichromate. 5 of these nuts are used to attach the dash pad to the painted steel upper dash panel  (D1ZZ-65044D90-A) on 1971-73 Mercury Cougar and Ford Mustangs. Sold individually.Replaces Ford part number 45271-S36.

Bolts and installation kit for most 1970-73 Mercury Cougar and Ford anything, including Mustang with V-8 engines. Kit includes main pivot bolt and adjusting bolt as shown. Spacer not included, but available used.

Used on front re-tractors, two per side on either side of the re-tractor mounting hole. Used to prevent rattles.

This fits behind the door panel and is needed to install your remote mirror correctly.*NOTE*1969 Cougar owners do not need this part as it is built in the the chromed plastic, rectangular bezel on the door panel.

Replaces Ford Part # C8AZ-2B164-A Sold individually

Kit includes two brackets and grommets for routing battery cable between starter and solenoid on inner fender. Replaces Ford Part # : C5ZZ-14302-K

Used seat belt bolt washer for the Mercury or Ford.

These Spark Plug Wire Separators are made of high-quality ABS plastic. Constructed to hold both standard 7mm and 8mm high-performance spark plug wires. Fits directly on valve cover clip. Available in blue, red and OE black.

Used plastic clip for the Mercury Cougar or Ford Mustang.

Reproduction set of four 2 3/4" black phosphate bolts for the 2 1/4" fan spacer on the 67 - 73 Cougar or Mustang.

D1ZE-9431-B 351-4V Cleveland factory original cast iron exhaust manifold for driver side. At some point there may have been a D1ZE-9431-BA casting number used, which may be substituted as per the Master Parts Catalog. *351C-4V exhaust manifolds only match up to factory 4V intake manifold ports and some aftermarket aluminum intakes such as offered by Weiand and Edelbrock.

351-2V Cleveland, factory cast iron 2V exhaust manifold set, both correct right D2OE-9430-BA and left D1ZE-9431-AA or D3AE-9431-AA side matching exhaust manifolds.

D2OE-9430-BA 351-2V Cleveland engine, factory original cast iron exhaust manifold for passenger side. *351C-2V exhaust manifolds only match up to factory 2V intake manifold ports and some after market aluminum intakes such as one offered by Edelbrock.

351C VALVCOVER Ford engine blue painted valve cover with "Powered by Ford" embossed in the metal. Correct on 1970-1973 Mercury Cougar and Ford Mustang with 351C engines. Ford master parts catalog shows a right and left version of this cover those Service Replacement numbers are D2SZ-6582-A & D2SZ-6582-B. Although we have more of these in inventory, we do not recommend them because the remaining quantities will be less than desireable. *Note - This cover will not work on a 351 Windsor engine. ...

Nice reproduction oil dipstick made from all steel, painted Ford engine blue. Only fits 289 or 302 Ford engines from 1967-73. These dipstick tubes have the 'full' and 'add' markings in the correct place, however they do not have any Ford part numbers stamped on them. Black steel as shown, not plain shiny steel like originals. Replaces Ford part # C7OE-6750-B or C8OE-6750-B.

351-4V Cleveland factory cast iron 4V exhaust manifold set, both correct right and left set of matching exhaust manifolds. Manifolds the same 1971-1973.

D3AZ-6758-B All steel tube that was used on 1973 H code 351-2V engines, one end inserted into the rear of the carburetor vacuum fitting (had a rubber hose connecting them 6N664) and the other end inserted into the straight end of the D3-6A664-2V PCV hose. This is a formed tube with barbed ends, it does not use clamps. *Note - Excludes 1973 Q code 351CJ engines.

D3AZ-6758-C All steel tube that was used on 1973 Q code 351-4V or 351CJ engines, one end inserted into the rear of the carburetor vacuum fitting (had a rubber hose connecting them 6N664) and the other end inserted into the straight end of the D3-6A664-4V PCV hose. This is a formed tube with barbed ends, it does not use clamps. *Note – Excludes 1973 H code 351-2V engines.

D1AZ-6788-A Metal tab that bolts to the intake manifold and has a hole for the round hose retaining ring (part number D2AZ-14A163-K). 1972-1973 all 351 engines, *Restoration Tip - These were painted Ford engine blue when the engines were painted, so paint it Dark Ford engine blue.

D2AZ-14A163-K Black plastic ring that barely fits over the PCV hose. Ring end locks into the D1AZ-6788-A hose bracket. Fits all 1972-73 351 engines, both 2V and 4V engines. This retaining ring came from Ford's electrical section.

Used 1970-72 black AUTOLITE marked oil fill cap with black plastic elbow. Several variations noted from our collection, AUTOLITE and MOTORCRAFT versions. Will need detailing or fresh black paint applied. Would also suggest replacing the rubber grommet. These 50 year old rubber grommets are rock hard and likely leak air. Gasket to valve cover will also need replacement. Even though this cap has a 1971 parts number, we see these on the 1970 351C engines quite often. Replaces Ford part...

Chromed dipstick tube and dipstick for the 351 Cleveland. Average quality part, made in China. Replaces Ford part # D0ZZ-6750-K.

This oil filter is absolutely concours correct. A must for Show. All are silk-screened with multiple colors.

Used oil screen pick up tube assembly from a 1970-74 small block 335 series, or 351C or Cleveland Ford car. This is for front sump oil pans. Used item, should be degreased and cleaned inside and out prior to installation. Tube assemblies with damaged screens, damaged tubes or bends are thrown away or scrapped. We only save undamaged, used oil pick up tubes. Melling sells a quality reproduction of this item. Replaces Ford Part #: D1AZ-6622-A

Rubber oil pan gasket for the 351 Cleveland engine in the 1970, 1971, 1972 and 1973 Mercury Cougar or Ford Mustang.

D1ZE-6312-C Application - Q code 351 Cobra Jets with air conditioning and power steering. Triple sheave pulley, 6-11/16" and 7-9/16" diameters. Ford Master Part number D1ZZ-6A312-A. *Note - References also list casting number D1ZE-6312-CA as being the same.

D2AE-6312-A Application is for both H and Q code 351 engines without air conditioning and without power steering. Single sheave pulley, 6-3/8 inches in diameter and 4-1/8 inches long. Ford Master Part number D2AZ-6A312-A.

A nice reproduction oil pan in Chrome finish for the 351C. Replaces Ford Part #: D0ZZ-6675.

The oil filter made by the original Ford supplier.

Single sheave pulley 6-61/64 inches in diameter.Applications:1970 Boss 302 Eliminators without power steering1970 351 engines without power steering1971 - 1973 351 engines without power steering and without A/C.Ford casting number C9OE-8509-E. Ford part number C9OZ-8905-B *Note - this is a very shallow pulley, it is meant to run in the second belt position from the engine. ...

Reproduction gold dichromate 10 blade alternator fan. Used on Mercury Cougars and Ford Mustangs manufactured after 11/17/1969. Actually this is a Ford part found on most all Ford automobiles from 1970-73. 10 blade alternator cooling fan. Replaces Ford Part #: DOAZ-10A310-B

Famous 'Cal Custom' aluminum finned oil pan that was so popular throughout the 60's, 70's and 80's. It has not been available for years, but it is back again. Pan is made from all new pressure die cast tooling and then fully machined to offer a precise fit and leak free installation. These look great in combination with the Finned Air Cleaner and Valve Covers. Replaces Ford Part #: C5ZZ-6675.

New gaskets for installing your intake manifold. This is the Felpro branded gasket. Fits 1964-73 small block Ford engines with size 260/289/302 cubic inches. C code 289-2V, A code 289-4V, F code 302-2V, and J code 302-4V.*Note - Excludes 1969-70 Boss 302 engines.

New gaskets for installing your intake manifold. This is the Felpro branded gasket. Fits all 1970-73 Ford 351C engines with 2 barrel intake manifolds 1969-70 Mercury Cougar and Ford Mustang with 351C-2V engines. This gasket set includes a metal pan gasket.Any doubts? 351 Windsor engines have 6 bolts holding the valve covers in place. 351 Cleveland engines have 8 bolts holding down the valve covers.*Note - Excludes 351W engines. *Note - Excludes 351C-4V Cleveland engines. ...

D3-6A664-4V Original used hose that connects the oil cap mounted PCV valve and the metal hard line on 1973 Mercury Cougar and Ford Mustang Q-code 351CJ engines only. Used hoses will have faded Motorcraft markings (if present). Very often the rubber will be hard and showing some degree of stress cracks. *Note - Excludes all 1969-72 351, and 1973 351-2V engines. *Note - These molded and contoured hoses were designed to work with original style PCV valve (modern 90° PCV valves won't...

This little device may not appear to be all that important, but it has a big job to do when your engine gets too hot. The threaded end looks a bit like an engine temperature sensor, and that's because it is. It's normally mounted on the intake manifold or engine block where it can sense coolant temperature.The three ports at the other end are for vacuum connections. One goes to manifold vacuum, another to carburetor vacuum, and the third goes to the vacuum advance on the distributor. At normal...

New rubber "O" ring for Ford V-8 distributors from 289/302/351W/351C/429 engines.

Used Distributor / 351C-2V for the 1973 Mercury Cougar / 1973 Ford MustangFord part number D3ZF-12127-BA  

C-4 transmission 90 degree brass fitting for the rear oil cooler line. New reproduction with jamb nut and "O"-ring. Fits 1967-68 Mercury Cougar and 1965-73 Ford Mustang where applicable.

Powerful oil filled coil that generates 40,000 volts, designed to work with the either of our Pertronix Ignitors. Sold in black or chrome. *Note - This coil is not necessarily needed with the Pertronix Ignitors, the stock Ford coil works fine for most applications.

Concours correct Autolite spark plug wires for any 1972-73 Mercury Cougar Eliminator or Ford Mustang with 351C engines. Black wires with 'Motorcraft', 'SIPCON', and the cylinder numbers individually imprinted on the 7mm wires. Orange spark plug boots on this set.

Reproduction hold down clamp rivet for the 67 - 73 Cougar or Mustang. This rivet holds the clip / clamp onto the distributor. Sold individually, 2 per car.

Pertronix brand 7mm spark plug wires. These are performance oriented wires compared to the concours spark plug wires. For any 1967-73 Mercury Cougar and Ford with 289 or 302 engines. Black wires and boots, quality spark plug wires taylor made for the small block Ford engines. Recommended by Pertronix for use with the Flame Thrower coils.

Pertronix brand 7mm spark plug wires. These are performance oriented wires compared to the concours spark plug wires. For any 1967-73 Mercury Cougar and Ford with 351 - 390- 428 - 429 engines. Black wires and boots, quality spark plug wires taylor made for 351 engines and the big block Ford engines. Recommended by Pertronix for use with the Flame Thrower coils.

NOTE: WE SUGGEST LOCAL PICK UP ONLY FOR CORE ENGINE BLOCKS BECAUSE WE CANNOT GUARANTEE BLOCKS WILL NOT HAVE CRACKS INTERNALLY. Long block, factory Q code 351CJ-4V V-8 engine. 351 Cleveland engine rated at 266 Hp with 8.0:1 compression ratio in 1973. These engine blocks have the 4 bolt main caps. Likely 0.030" bored motor that may or may not have been in running condition when pulled. Guaranteed to be rebuildable. Complete engine less carburetor, exhaust manifolds, fan, distributor,...

NOTE: WE SUGGEST LOCAL PICK UP ONLY FOR CORE ENGINE BLOCKS BECAUSE WE CANNOT GUARANTEE BLOCKS WILL NOT HAVE CRACKS INTERNALLY.Used standard bore 4.00" Ford 351C 1971-73 engine block. Will be used, dirty, have measurable taper, and will have a ridge. Good for rebuild. Bare block, may have D0AE, D2AE, castings. When we have them in stock we will post the casting date or dates. Heavy, will require either local pickup or freight shipping. Dated 2C7 or March 7, 1972. D2AE-6015-CA.This item...

Reproduction chrome heater hose elbow is for 351, 390, and 428CJ engines. Replaces Ford Part # D0AZ-18599-C Barbed End: 5/8" hose barbThreads: 1/2" NPT (Tapered Threads) For some helpful tips on upgrading your Cougar (or Mustang) cooling system, check out our video: ...

New 13 Pound Generic Radiator Cap with Safety Release for the 1967 - 1973 Mercury Cougar / Ford Mustang

Cast construction with very good quality chrome. Looks great with chrome valve covers and air cleaner. Replaces Ford Part #: D0ZZ-8592-A.