Interior

1967 Cougar Owners: To view our exploded view interactive diagram of the tilt steering column parts, click here. This is the part of the tilt switch that the turn signal wand screws into. This part is always included when you purchase a new turn signal switch. 1967-69 mechanism has two springs on either side, the 1970-73 mechanism uses just one spring. There is an active thread on the Classic Cougar Community Forum discussing tilt columns and trouble shooting. *NOTE* For tilt column service,...

Ford called this part a 'sleeve'. Attaches to the lower shifter arm with a hitch pin. Has nice bushing, with correct nut, washer, and pin. The 1967/68 and 1969/73 versions are identical. The C1AA-7353-C sleeve has fine threads, the C9OZ-7353-A has course threads. Fits all 1967-73 Mercury Cougar and Ford Mustang, and we suspect many other Ford vehicles beginning in 1961. This fine thread version is hard to keep in stock, consider the 1969-73 course thread version as an alternative. Check out...

Correct texture and molded-in colors, with steel insert molded into foam to increase strength. Extra thick vinyl skins. American made. Replaces Ford part # C8ZZ-6524100-BK.

Although many would disagree, these are in my opinion average quality. "BUT" they are currently the best available reproduction. The inner portion where your fingers go have too sharp of edges and they do not hold up nearly as well as the originals do. We also have used available. Available in Black, Dark Red, Blue, Parchment, Ivy Gold, Aqua , Saddle, or Nugget Gold. Replaces Ford part # C8ZZ-6524100 and C8ZZ-6524101. *NOTE* The Ivy Gold and Aqua armrests are not correctly colored for the...

This armrest is correct for the 1968 Shelby / Ford Mustang, but works well as a reasonably close substitute for the 1967 - 1968 Mercury Cougar XR7. The contour is the same as found on the 1968 XR7, the 1967 XR7 had more squared off edges. The texture is not course like the XR7, but rather smooth to match the grain of vinyl on the perimeter of the XR7 door panels, sides of seats and Cougar dash pad. It does not look out of place in my opinion and is what I would consider to be average to good...

This armrest is correct for the 1968 Shelby / Ford Mustang, but works well as a reasonably close substitute for the 1967 - 1968 Mercury Cougar XR7. The contour is the same as found on the 1968 XR7, the 1967 XR7 had more squared off edges. The texture is not course like the XR7, but rather smooth to match the grain of vinyl on the perimeter of the XR7 door panels, sides of seats and Cougar dash pad. It does not look out of place in my opinion and is what I would consider to be average to good...

Used driver side (left hand) rear armrest for the Mercury Cougar that is in grade A condition. Grade "A" armrests are not pulling away from their backing and have no splits, cigarette burns or other obvious defects. They may need to be painted with vinyl paint, especially since we can almost guarantee we will not have both sides in your color in stock. Please indicate in the notes which color you would prefer, we will do our best to accommodate you. *NOTE* If you have a standard or decor 1967...

Good used armrest with no cracks or cigarette burns. The lighter colors like aqua and white often need to be repainted as they show discoloration more often than the darker colors. The armrests shown were all taken from 1969- 1970 Decor and XR7 Cougars. Standard model Cougars did not have rear armrests in 1969 - 1970 Coupes. Unlike the 1967 - 1968 rear armrests the 1969 - 1970 rear armrests are far less prone to pulling away from their backing. These armrests are also a direct fit to your 1967...

Good used armrest with no cracks or cigarette burns. The lighter colors like aqua and white often need to be repainted as they show discoloration more often than the darker colors. The armrests shown were all taken from 1969- 1970 Decor and XR7 Cougars. Standard model Cougars did not have rear armrests in 1969 - 1970 Coupes. Unlike the 1967 - 1968 rear armrests the 1969 - 1970 rear armrests are far less prone to pulling away from their backing. These armrests are also a direct fit to your 1967...

Good used armrest with no cracks or cigarette burns. The lighter colors like aqua and white often need to be repainted as they show discoloration more often than the darker colors. The armrests shown were all taken from 1969- 1970 Decor and XR7 Cougars. Standard model Cougars did not have rear armrests in 1969 - 1970 Coupes. Unlike the 1967 - 1968 rear armrests the 1969 - 1970 rear armrests are far less prone to pulling away from their backing. These armrests are also a direct fit to your 1967...

Four per car unless you have a 1968 decor or standard model that has the unique three hole armrest and then you will need six. Replaces Ford part # C7AZ-6224146. Check out our handy diagram below to find other '67-'68 door parts you may need. All the item numbers shown can be typed in to the search bar on our site. (Click image to view full size) ...

Used upper steering column bearing for your 67 - 73 Cougar or Mustang. One required per car. Fixed Columns only use the upper bearing, while the tilt columns used an upper and lower. The used lower bearing can be found here. Outside diameter: 1 3/16 " * - may not fit some 67 Mustang applications with a fixed column as these used Ford part # C4OZ-3517-A, which is the same part used in the Fairlanes/Comets with a fixed column. To our knowledge this bearing is not currently reproduced. *NOTE* For...

NOTE: At the moment the supplier is only making the late model version of this beltline kit. The late version has a slight bend in the chromed quarter piece, whereas the early version is straight (see photo above). Made With Exact Materials As Original. Eight piece kit that includes inner and outer belt-line, enough for both pieces of door and quarter glass. These strips run horizontally against your glass and keep water and debris from entering your rear quarter panels and doors causing them...

This is a very hard to come by one year part used on both the Mustang and Standard - Decor level interiors on the Cougar. Whereas the plastic base and pad this attaches to can easily be modified from automatic configuration to manual, this part cannot. This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of 50% of our web price for parts delivered in hand or by carrier to our Brooks,...

Emergency flasher bezel for the side of the tilt steering column. Another hard to find, fragile, plastic part. Subject to availability. Paint to match your interior.

Used bezel for the dual head rest found in the Mercury Cougar or Ford Mustang. This bezel measures 3 1/2" long and is correct for all 1968 models that use this part (including Shelby and Ford Mustang except the XR7 Mercury Cougar. Due to extra thick seat foam, the XR7 uses a taller bezel. Good used part with no peeling chrome or obvious cracks (may have hairline crack in threaded area). Ford originally had a special tool for installing and removing these guide sleeves. Ford tool division was...

Used bezel for the dual post head rest for the Mercury Cougar XR7. This bezel measures 4" long and is correct for the XR7. Due to extra thick seat foam, the XR7 uses this taller bezel. Good used part with no peeling chrome or obvious cracks (may have hairline crack in threaded area). Ford originally had a special tool for installing and removing these guide sleeves. Ford tool division was known as Rotunda. Down deep near the threads is a molded hex shape that allowed a tool to tighten without...

This is the correct horn panel bezel for all 1968 Cougar XR7 steering wheels. The satin paint will need to be resprayed but the two mounting studs are in place and there are no cracks or burns. Unique to the XR7, identified by having the grey inserts. Please see related for standard model bezel.Ford part number C8AA-3D754-A. * Note - Will not work on standard model Cougar pads without removal of the inserts.

Reproduction pair of black seat belt buckle bezels for the Mercury Cougar, Ford Mustang, or Ford Torino. It is little details like these that often make the difference between first and second place at the show. 

Very rare find... A restored bezel will look fine but will never retain the sharp edges and matte black finish like this new in the box original Ford part.

This shift indicator will work on a 1967 or 1968 Cougar or Mustang equipped with automatic transmission. It comes with all items shown here.

Inner front bolt, long length to clear sound deadener. Used in conjunction with a thick, gold spacer washer.

Rear seat belt bolt, four per car used in conjunction with two red washer / spacers. 13/16" hex head, 1-1/4 inch bolt with a 3/16 inch shoulder. Can be either smooth headed or have a Heavy or Light "A". There is another version of this same bolt with a smooth head and no markings.

Used Vent Frame Bolt Kit 1967 and 1968 Mercury Cougar and Ford Mustang.Consists of: 1 bolt - 379384-S2 1 bolt - 378694-S 2 lock nuts - 33797-S2 set screws -  375694-S2

This flexible vinyl cover attaches to the upright brackets that mount your center fold down arm rest. The number stamped on the back for the cover closest to the driver is C5ZB-6561693-BW. If yours is other than black in color the BW will be something else. Very rare part that is difficult to obtain.

This flexible vinyl cover attaches to the upright brackets that mount your center fold down arm rest. The number stamped on the back for the cover closest to the driver is C5ZB-6561692-BW. If yours is other than black in color the BW will be something else. Very rare part that is difficult to obtain.

Unique pedal that works with the wider collapsible 1968 steering column and with a clutch pedal. Longer arm than drum brake pedals. Keep in mind automatic transmission brake pedals can be trimmed down to work as manual transmission pedals. Pedal shipped bare, picture may show hardware and pedal pad with trim. *Note* On some 1968 Cougars you will have to drill holes in your existing pedal hanger (many are pre-drilled) to accomomdate the power brake pedal. Since systems with a vacuum booster...

Pictured here is a representation of the console you can expect to get from us. Notice this is not a restored console, but rather a compilation made from several units taken out of parts cars to make one good example. As with the console shown here, it will not be perfect. If you would like to know where the blemishes are on the console you will receive, please contact us for details. Do know we understand how delicate they are and make every effort to ensure it is packaged properly. We do...

Pictured here is a representation of the console you can expect to get from us. Notice this is not a restored console, but rather a compilation made from several units taken out of parts cars to make one good example. As with the console shown here, it will not be perfect. If you would like to know where the blemishes are on the console you will receive, please contact us for details. Do know we understand how delicate they are and make every effort to ensure it is packaged properly. We do...

This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of 50% of our web price for parts delivered in hand or by carrier to our Brooks, Oregon location. If you're not interested in store credit, just shoot us an email and we will let you know if it's is something we can pay cash for. We do not send cash for parts in advance but we often can compensate you within hours of receiving the...

Nice original Saddle XR7-G center console with original leather and all pieces intact with no cracks. This unit is trimmed for a car with factory A/C. Harness to fog lights and sunroof sold separately. Ford part # C8WY-65045A36-X1A for the lower main body. This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of 50% of our web price for parts delivered in hand or by carrier to our Brooks,...

Good used base for the XR7G with no cracks. The Cougars equipped with air conditioning had the last few inches trimmed off. It is a rather rough, hand cut from the factory.  *NOTE* The base shown has been cut for AC.

Two of these clips per side are required to hold the interior padded pillar pads the the "A" pillars on your 1968 Cougar.Replaces Ford part number 381896-S2.

These little clips are what were used to fasten the dash face pad to the dash bezels on a 1968 standard or decor level Cougar. They are very difficult to come by and we have yet to find a suitable substitute. We suggest that if you need more than a few of these clips that you consider using strips of adhesive Velcro in lieu of these clips as Velcro holds the fragile aluminum trim more evenly against your bezels and is easier to install and remove for future maintenance. *NOTE* There are 13 of...

C7WY-15000-A 1967 - 1968 Standard Cougar body code 65A or 65C, found optionally in the small center pod of the instrument cluster. Used clocks generally do not work after 40 years. These are considered cores. We also offer clocks with modern quartz movements or NOS movements in restored clocks. Check out the videos below on our new gauge tester and the "Cougar Dash Surgery Clock and Speaker Install by Andrew Chenovick: ...

Used clock for the center console equipped Mercury Cougar XR7. Most used clocks typically do not work after 40+ years and you can also expect that the lens will have some cracks. However, we offer a nice reproduction lens or restored clocks with a modern quartz movement or NOS movement.Ford part # C7WY-15000-B.Check out the video below on our new gauge tester: This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we...

NOS plastic brackets that screw to your roof and then slide a vinyl colored piece over. Sold individually, two are required per car. Ford part # C8AZ-6229232-A.

NOS white colored coat hooks pair. Reproductions only come in black, these are new in the package. White color started in 1970, off white and parchement 1968-69. Fits 1968-73 Mercury Cougar and Ford everything including that Mustang. Ford Part #: D0AZ-6229024-K.

Developed on a 3D printer, good fit but notice the texture is not the same. Four speed and Automatic transmission use the same bezel.

This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of 50% of our web price for parts delivered in hand or by carrier to our Brooks, Oregon location. If you're not interested in store credit, just shoot us an email and we will let you know if it's is something we can pay cash for. We do not send cash for parts in advance but we often can compensate you within hours of receiving the...

NOS dash face pad for the standard Mercury Cougar equipped WITH air conditioning. This unit will be like new and will not have any cracks. Includes surround trim, but without mounting clips. *NOTE* Attaching clips for this unit are like hen's teeth. We suggest using velcro strips that will secure this unit to your dash.Check out the "Cougar Dash Surgery, Clock and Speaker Install" video by Andrew Chenovick: ...

This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of 50% of our web price for parts delivered in hand or by carrier to our Brooks, Oregon location. If you're not interested in store credit, just shoot us an email and we will let you know if it's is something we can pay cash for. We do not send cash for parts in advance but we often can compensate you within hours of receiving the...

This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of 50% of our web price for parts delivered in hand or by carrier to our Brooks, Oregon location. If you're not interested in store credit, just shoot us an email and we will let you know if it's is something we can pay cash for. We do not send cash for parts in advance but we often can compensate you within hours of receiving the...

Many people seek this part when changing their XR7 over to factory installed AC. Not only will we give you a substantial credit when you send in your non AC center bezel, we will also carefully match our stock to your bezel to ensure ours does not look out of place when place next to your existing panels. If you send in a substantially faded panel for exchange we will credit back $$$.Finding Grade A dash panels which do not have any fading is nearly impossible. Check back we do get them...

This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of 50% of our web price for parts delivered in hand or by carrier to our Brooks, Oregon location. If you're not interested in store credit, just shoot us an email and we will let you know if it's is something we can pay cash for. We do not send cash for parts in advance but we often can compensate you within hours of receiving the...

New Tooling as of May 2016! The previous version had a heavier grain than original and had a built in defect / scratch on the driver side top. This new version is the best repro Cougar pad offered to date, satisfaction guaranteed. Reproduction dash pad in black for the 1967 and 1968 Mercury Cougar. This is the same Dashes Direct pad you see advertised elsewhere. Beware of the "other" brand of dash pad out there, it will not fit. First off I must say this is the best version of this much needed...

Good used original upper black dash pad. The pad shown is for a 1968 but will work a 1967. The difference is the 68 has a relief cut for the aluminum VIN tag located on the passenger side and 67 did not. Grade B dash will have no cracks, possible missing corner stud and not as soft and pliable as Grade A version. ...

New old stock deluxe shifter handle in light aqua. Perfect condition, no cracks in the plastic. No release button or set screw included. NOS Ford part number C8OZ-7213-AQ The 67 version was actually a little different. Check out our video on rebuilding your shifter below: ...