Home > 1973 Mercury Cougar
All Available Parts - 1973 Mercury Cougar
Products (Click sub-categories above to ONLY display results for that Sub-Category) 2901-3000 of 3319
Sorted By:
Availability:
Display Options:
Availability: Out of Stock
Item #: 25562 -
D3AZ-6758-C All steel tube that was used on 1973 Q code 351-4V or 351CJ engines, one end inserted into the rear of the carburetor vacuum fitting (had a rubber hose connecting them 6N664) and the other end inserted into the straight end of the D3-6A664-4V PCV hose. This is a formed tube with barbed ends, it does not use clamps. *Note – Excludes 1973 H code 351-2V engines.
Availability: Out of Stock
Item #: 25272 -
D1AZ-6788-A Metal tab that bolts to the intake manifold and has a hole for the round hose retaining ring (part number D2AZ-14A163-K). 1972-1973 all 351 engines, *Restoration Tip - These were painted Ford engine blue when the engines were painted, so paint it Dark Ford engine blue.
Availability: Out of Stock
Item #: 25495 -
D2AZ-14A163-K Black plastic ring that barely fits over the PCV hose. Ring end locks into the D1AZ-6788-A hose bracket. Fits all 1972-73 351 engines, both 2V and 4V engines. This retaining ring came from Ford's electrical section.
Availability: Out of Stock
Item #: 25552 -
Used on front doors of cars produced after 10-1-71 with no factory door speakers. Ford part number D2AZ-7630322-A, casting number D3AB-6523342-AA. Very hard to find with plastic knob still intact.
Availability: Out of Stock
Item #: 30263 -
Heavy duty door hinge rebuild kit for the 1971 - 1973 Cougar or Mustang. Included in the kit are:2 Machined hinge pins2 Machined steel tubes4 Oil impregnated bushings2 Stainless steel washers2 Zerk FittingsEach kit is enough to do one side and includes one big and one small pin / tube set.
Availability: Out of Stock
Item #: 25366 -
Aluminum clip on guards for the rear edge of the 1971 - 1973 Cougar doors. Would have been part of the exterior decor option. Self attaching, no adhesive or screws needed. Specifically contoured to the Cougar door edge. Ford part number D1WY-6220910-A.
Availability: Out of Stock
Item #: 25380 -
Right side factory aluminum door guard.
Availability: Out of Stock
Item #: 32022 -
NOS aluminum clip on guards for the rear edge of the 1971 - 1973 Cougar doors. Self attaching, no adhesive or screws needed. Specifically contoured to the Cougar door edge. Ford part number D1WY-6220910-A.
Availability: Out of Stock
Item #: 31671 -
This mirror nut for the 70 - 73 Cougar or Mustang is made from stainless steel, as compared to the other reproduction we offer which is made from die cast metal. A few benefits of the stainless steel nut is that the finish on it will not tarnish over time, and that it cannot be cross threaded.
Availability: In-Stock Item
Item #: 31940 -
This NOS remote mirror came to use without a Autolite or Motorcraft box. Current offering while new and never installed does have a small manufacturers defect in the casting as shown. Found on the drivers side of standard model Cougars, no passenger side mate was ever offered with this mirror. Two different versions of this mirror are found on 1971-73 Mecury Cougars, either casting number D1WB-17743-AA or C9AB-17743-A. This mirror has the Ford casting number D1WB-17743-AA. Do...
Availability: Out of Stock
Item #: 32440 -
This unique gasket is only slightly different from the driver side. The angle at the front is just a little different and notice it does not have a hole drilled for the remote mirror cable used on the driver side. This gasket was also used on the 1971 Ford Torino / Ranchero and Mercury Cyclone. This is an upgrade over the reproduction we carry for a 1969 - 1970 Cougar that has a passenger side Sport Mirror. The Ford Engineering number seen on the pad reads D1OB-17724-AA. Do you have questions...
Availability: Out of Stock
Item #: 12223 -
Whenever you take on a door job, its always handy to have a few things available....a helper, a floor jack and a door hinge wrench. While a helper and floor jack might not always be available, a door hinge wrench is a valuable tool to have around when removing / setting a door. This Snap on obstruction wrench (google snap on part # S9608B) is specially curved to allow you to gain access to a few of those hard to reach bolts on your door hinges. We will loan this door hinge wrench for 60 days,...
Availability: Out of Stock
Item #: 26943 -
Used manually adjustable grade "A" side view mirror for the Mercury Cougar Standard or Ford Galaxie. This ambidextrous mirror can be installed on either the passenger or driver side door. This good used mirror will have good glass and nice chrome for your restored or nice original Cougar or Galaxie. Also used on various 1967-73 full sized Ford and Mercury cars. Replaces Ford part # C7AZ-17696.Dimensions: Base Hole Spacing: 5-7/8"Base Length: 6-5/8"Overall Height: 5-1/8"Mirror Width:...
Availability: Out of Stock
Item #: 26944 -
This used grade "A" remote mirror has chrome that looks great and the adjustment wand is unbroken and working. Used on the drivers side of standard Cougars, no passenger side mate was ever offered with this mirror. Two different versions of this mirror are found on 1971-73 Mecury Cougars, either casting number D1WB-17743-AA or C9AB-17743-A will be supplied.Replaces Ford part numbers D1WB-17743-AA and C9AB-17743-A.Do you have riv-nut questions? Here are riv-nut answers! ...
Availability: Out of Stock
Item #: 20065 -
This plastic fastener is used to keep your mirror cable from interfering with the movement of your door glass. It is located at the front of the door near the top.
Availability: Out of Stock
Item #: 22621 -
Reproduction rubber bumper for your 67 - 73 Cougar or Mustang door latch mechanism. The bumper sits on the inside of your door latch mechanism, and is there to dampen the blow from the striker when you close your door.
Availability: Out of Stock
Item #: 25286 -
Used passenger side (right hand) sport mirror that is correct for the Mercury Cougar. This will also work on 1969-70 Cougar, but base height is just a little bit taller. *NOTE* We are currently out of good used mirrors with original bases so if you order this part you will get an original mirror with a reproduction base. Do you have questions about installing a passenger side mirror or using Riv-Nuts? Have more questions about installing a passenger side mirror or Riv-Nuts? Got a mirror lens...
Availability: Out of Stock
Item #: 25315 -
This used grade "B" remote mirror has chrome that looks shabby, adjustment wand is unbroken and working. Used on the drivers side of standard Cougars, no passenger side mate was ever offered with this mirror. Two different versions of this mirror are found on 1971-73 Mecury Cougars, either casting number D1WB-17743-AA or C9AB-17743-A will be supplied.Replaces Ford part numbers D1WB-17743-AA and C9AB-17743-A.Do you have riv-nut questions? Here are riv-nut answers! ...
Availability: Out of Stock
Item #: 23418 -
Ford Casting number as seen on the bottom side is D1OB-17713-AWA. Many people misinterpret it as D10B-17713-AWA, DI0B-17713-AW or Dl0B-17713-AWA. Perfect base with no cracks or bends. Visually it is impossible to tell this part from 1970 with a D0OB-17713-AW casting number on the bottom. The Pastel Blue base is from a 1970 and the Red base from a 1971. Even when placed side by side it is hard to tell the difference. Do you have questions about installing a passenger side mirror or using...
Availability: Out of Stock, On Order
Item #: 24005 -
Used manually adjustable grade "B" side view mirror for the Mercury Cougar Standard or Ford Galaxie. This ambidextrous mirror can be installed on either the passenger or driver side door. This good used mirror will have good glass and will have some pitting in the chrome as shown. Also used on various 1967-73 full sized Ford and Mercury cars. Replaces Ford part # C7AZ-17696.Dimensions: Base Hole Spacing: 5-7/8"Base Length: 6-5/8"Overall Height: 5-1/8"Mirror Width: 5-1/8"Mirror Height: 3-5/16"...
Availability: Out of Stock
Item #: 31711 -
Concours? almost, these are stainless steel screws with the wax tipped coating like the originals, for installing the door sill plates. The wax was deemed necessary by the Ford Motor Co. as a seal. These can be used on all years 1967-73 Mercury Cougar, Ford Mustang and most all other Ford, Mercury, Lincoln cars of the era. Works well with any of the reproduction sill plates, these were really made to be used with the premium reproduction sill plates in stainless steel. 1967-68 Cougar and...
Availability: Out of Stock
Item #: 25582 -
Ford offered the 1973 Mercury Cougar hood emblem in two versions as a service replacement part. It is very rare to find them new in the box with the chrome center hood moulding, usually they are found without the chrome. This was found at the Spring 2007 Ford Carlisle show. Once its gone I doubt we will see another anytime soon. Keep in mind we are always looking for Texaco gas station memorabilia for trades! At this point we are mostly looking for poor condition signs. Will consider good...
Availability: Out of Stock, On Order
Item #: 26151 -
This is an exact replacement for a 1970 remote sport mirror. Nearly indistinguishable from a 1968. Obviously a larger ball and longer than found on 1969, 1971-73 remote mirrors. This threaded replacement wand will require you to cut 8/32" fine threads in your original controller. Your OEM mirror controller is made of a very soft metal so one can often install these as "self tapping".1967 and 1968 are different, see comparison picture. The 1968 version was rounded off due to new safety...
Availability: Out of Stock
Item #: 26612 -
Original used hard plastic sport mirror pad / gasket. Correct for driver side sport mirrors for the 1971-73 Cougar and passenger side sport mirrors 1970-73. Ford engineering # C90Z-17724-B and D1WB-17C701-AB. Do you have questions about installing a passenger side mirror or using Riv-Nuts? Have more questions about installing a passenger side mirror or using Riv-Nuts? Got a mirror lens that flops around in your Sport Mirror every time you hit a tiny bump in the road? WCCC to the rescue! ...
Availability: Out of Stock
Item #: 26613 -
This used driver side (left hand) mirror pad / gasket for use with a standard manual adjust chrome mirror. This unit will not work with a painted sport mirror or any remote mirror. Ford Engineering # imprinted on pad is C7OB-17C701-AA or C8OB-17C701-A. Do you have questions about installing a passenger side mirror or using Riv-Nuts? Have more questions about installing a passenger side mirror or using Riv-Nuts? Got a mirror lens that flops around in your Sport Mirror every time you hit a...
Availability: Out of Stock
Item #: 11-0301 -
Inside door handle release mechanism for the driver side on base model standard 1972-73 Cougar and Mustang. This latch mechanism went through a couple of revisions by the end of 1973. Ford calls this part a 'control and link assembly', this particular one only works with the base door handles as shown in the photo. The Ford MPC describes those door handles as fitting the door panels with detachable armrests, instead of the molded armrests on the door panels, as found on the XR7 and Decor...
Availability: Out of Stock, On Order
Item #: 26324 -
Concours? almost, these are stainless steel screws with the wax tipped coating like the originals, for installing the door sill plates. The wax was deemed necessary by the Ford Motor Co. as a seal. These can be used on all years 1967-73 Mercury Cougar, Ford Mustang and most all other Ford, Mercury, Lincoln cars of the era. Works well with any of the reproduction sill plates, these were really made to be used with the premium reproduction sill plates in stainless steel. 1967-68 Cougar and...
Availability: Out of Stock
Item #: 20541 -
This was an adhesive emblem and has long since fallen off most cars or was removed when the car was painted. We often times have driver quality emblems available, but be aware, they will have some pitting issues.Our reproduction 67-68 pillar emblem is a good substitute.Original Ford part number D1WY-6542532-A.
Availability: Out of Stock
Item #: 20647 -
This is one of the smallest "Cougar" emblems ever put on a Mercury Cougar. Only the 70-73 two spoke cat and xr7-G shift handle Cougar was smaller. It is also the most delicate! Very unusual to find the tail and all limbs intact on this fragile little kitty. Silver spray paint will make this cat look new again, they did not have a chrome finish from the factory. Now that we have reproduced this emblem there is little incentive to purchase this over-priced used emblem.
Availability: Out of Stock
Item #: 25375 -
Found on the C pillars of a 1971 - 1973 Mercury Cougar XR7 Coupe. We rarely get good used examples of these emblems as they are always badly faded. These mount on the lower part of the roof behind the quarter windows. This part of the roof is also known as the 'C' pillar.
Availability: Out of Stock
Item #: 20373 -
This little emblem was used only on the two spoke steering wheels from 1969 - 1973. We can pretty much guarantee one if not both of the two mounting studs will be broken but because of the way it fits into the recess of the steering wheel pad, gluing it into place is not a problem. We rarely have an emblem this nice in stock for more than a few weeks of any one year as the tail was prone to breaking off as well as the "cats" other limbs. We do not list these hard to find parts here to...
Availability: Out of Stock
Item #: 19509 -
This little emblem was used only on the two spoke steering wheels from 1969 - 1973. We can pretty much guarantee one if not both of the two mounting studs will be broken but because of the way it fits into the recess of the steering wheel pad, gluing it into place is not a problem. The tail will always be broken and probably at least one leg is missing on this grade B part. While not an exact fit our 3 spoke wheel emblem cat will fit on this black background.
Availability: Out of Stock
Item #: 25283 -
For 1971-73 Mercury Cougars and Ford Mustangs with the 351W engine manufactured after 10-26-1970. This is a Pitts manufactured pulley and clutch assembly with a pulley diameter of 6-5/16", a clutch diameter of 5-1/8", and an overall thickness of 1-11/16 inches. Ford part # D1OA-2981-A. May also have part numbers D1OA-2981-AA, D1OA-2981-A1A, D1OA-2981-A1B, D1OA-2981-A2A, and D1OA-2981-A2B.
Availability: Out of Stock
Item #: 19769 -
This is the correct emblem that came in the center of the hood moulding on a 1973 XR7 model Mercury Cougar. The price is absolutely ridiculous, I agree. Years ago when they sold for $250 I thought THAT was insane! Replaces Ford part # D3WY-16637-B.
Availability: Out of Stock
Item #: 25481 -
Stainless steel throttle pedal surround trim. Self attaching to part number D1ZZ-9735-B. This used part may have some wear, but will not have broken tabs. Fine steel wool really shines these up. It appears that this trim may not have been used all the way through 1973. Ford probably eliminated it as a cost saving measure.
Availability: Out of Stock
Item #: 27503 -
Dash pad attaching nut 8-32 threads original zinc plate and dichromate. 5 of these nuts are used to attach the dash pad to the painted steel upper dash panel (D1ZZ-65044D90-A) on 1971-73 Mercury Cougar and Ford Mustangs. Sold individually.Replaces Ford part number 45271-S36.
Availability: Out of Stock, On Order
Item #: 16124 -
Bolts and installation kit for most 1970-73 Mercury Cougar and Ford anything, including Mustang with V-8 engines. Kit includes main pivot bolt and adjusting bolt as shown. Spacer not included, but available used.
Availability: Out of Stock
Item #: 20655 -
This 1/2" tall unique little screw was used on several different trim parts on the early Mercury Cougars. In 1967 - 1968 there were eight per wheel lip moulding, two per fender extension moulding, two per center grille moulding and five per hood lip moulding for a total of 50 screws. In 1969-1973 they were used on the wheel lips mouldings. The 1971 - 1973 hood lip mouldings used the same screw but it was 5/8" tall.
Availability: Out of Stock
Item #: 41047 -
Reproduction disc brake hose bolt for any 1968-73 Mercury Cougar and generally all other Ford cars with factory disc brakes. Special hollow bolt with cross drilled hole. Attaches the high pressure hose to the caliper.
Availability: Out of Stock
Item #: 23780 -
Used on front re-tractors, two per side on either side of the re-tractor mounting hole. Used to prevent rattles.
Availability: Out of Stock
Item #: 26132 -
Used seat belt bolt washer for the Mercury or Ford.
Availability: Out of Stock
Item #: 14250 -
Reproduction of the plastic square hood insulation clips. 11 used on most vehicles. Sold individually.
Availability: Out of Stock
Item #: 18965 -
351C VALVCOVER Ford engine blue painted valve cover with "Powered by Ford" embossed in the metal. Correct on 1970-1973 Mercury Cougar and Ford Mustang with 351C engines. Ford master parts catalog shows a right and left version of this cover those Service Replacement numbers are D2SZ-6582-A & D2SZ-6582-B. Although we have more of these in inventory, we do not recommend them because the remaining quantities will be less than desireable. *Note - This cover will not work on a 351 Windsor engine. ...
Availability: Out of Stock
Item #: 19699 -
Used grade A rocker panel clip for the 71 - 73 Mercury Cougar
Availability: Out of Stock
Item #: 31973 -
Used 1970-72 black AUTOLITE marked oil fill cap with black plastic elbow. Several variations noted from our collection, AUTOLITE and MOTORCRAFT versions. Will need detailing or fresh black paint applied. Would also suggest replacing the rubber grommet. These 50 year old rubber grommets are rock hard and likely leak air. Gasket to valve cover will also need replacement. Even though this cap has a 1971 parts number, we see these on the 1970 351C engines quite often. Replaces Ford part...
Availability: Out of Stock
Item #: 33551 -
Used oil screen pick up tube assembly from a 1970-74 small block 335 series, or 351C or Cleveland Ford car. This is for front sump oil pans. Used item, should be degreased and cleaned inside and out prior to installation. Tube assemblies with damaged screens, damaged tubes or bends are thrown away or scrapped. We only save undamaged, used oil pick up tubes. Melling sells a quality reproduction of this item. Replaces Ford Part #: D1AZ-6622-A
Availability: Out of Stock, Discontinued
Item #: 14101 -
Chromed dipstick tube and dipstick for the 351 Cleveland. Average quality part, made in China. Replaces Ford part # D0ZZ-6750-K.
Availability: Out of Stock
Item #: 15381 -
Rubber oil pan gasket for the 351 Cleveland engine in the 1970, 1971, 1972 and 1973 Mercury Cougar or Ford Mustang.
Availability: Out of Stock, On Order
Item #: 31550 -
Made from polyurethane, a bit more rigid and stiffer than our rubber insulators. Sold individually. Two required per vehicle. These are the coil spring insulators available from most Mustang/Cougar suppliers. Replaces Ford Part #: C4DZ-5415-A.
Availability: Out of Stock, On Order
Item #: 26668 -
Tall version 1" thick and can be used with performance springs to bring the car to a stock ride height. Sold as a Pair. Replaces Ford Part #: C4DZ-5415-A.
Availability: Out of Stock, On Order
Item #: 11794 -
This reproduction universal joint fits the differential end of the drive axle and is used on all Mercury Cougars or Ford Mustangs equipped with the 289, 302, 351 Windsor as well as most 351 Clevelands (see chart). Includes a grease fitting for extended life. 3.25" span cups are 1.12" and 1.00" diam. Replaces Ford part # C3AZ-4635-F.
Availability: Out of Stock
Item #: 11793 -
One size fits all universal joint u-bolt kit. Complete kit required to attach universal joint to rear differential. This kit only works with the 1-7/8 inch U-joint caps. Many of the higher performance engines used 2 inch caps and the larger yokes. Replaces Ford Part #: C1AZ-4529-A or D3AZ-4529-A.
Availability: Out of Stock
Item #: 16-0047 -
Application; 390, 427, 351CJ, 428CJ, and 429CJ all with C6 transmission. 428CJ and 429CJ 4 speed transmissions. 1970 351C-4v with FMX.U-joint size 1330, overall length 8-3/4 inches.
Availability: Out of Stock
Item #: 31253 -
Good used axle vent nipple or tube. This vent tube screws into the top of the rear axle and is a breather / vent to equalize the pressure inside the axle tube. Fits both 8 inch and 9 inch rear axles. Fits Mercury Cougar and Ford Mustang 1967-73. A (5/16" inside diameter) rubber hose about 18-1/4 inches long attaches to the nipple. Has a very tiny diameter hole inside, about 0.062". Needs to be kept clear to work properly. Also see the reproduction version from AMK. Concours hose kit with...
Availability: Out of Stock
Item #: 16234 -
Used rear leaf spring retainer for 1967 -73 Mercury Cougar with competition handling or GT suspensions. Additionally it fits 1966-71 Mercury Comet / Montego / Cycolne, 1966-71 Ford Fairlane / Torino, all with HD or GT suspensions. Identified with a stamped number "2" on the top. The inside height is 1-29/32 or 1.91 inches. Sold individually, one for each side for a total of 2 per car. Bead blasted for pictures, most will ship 'as removed'. This suspension part never came painted, there will be...
Availability: Out of Stock
Item #: 10234 -
Reproduction mounting bracket. This is the mounting plate for the end links on the factory rear sway. Mercury Cougar 1970-73 only, this is not a Mustang part. The tab for the end links are mounted forward of the rear axle towards the outside of the car. These plates get sandwiched between the shock mounting plates and the Isolator clamps on your rear axle assembly. Sold individually and you will need two for the installation. Left is the same as right. The total width of this plate at its very...
Availability: Out of Stock
Item #: 25082 -
These are the U-shaped brackets that hold the round part of the rear sway bar. These mount to the rear frame rail. All 1970 - 1973 Cougars should have these mounting holes from the factory, 1969 and earlier Cougars do not have these holes. Two clamps needed for installation.
Availability: Out of Stock
Item #: 25497 -
Bracket mounts to top of stock cast iron Cleveland intake manifold, holding the throttle cable. All 351C engines, 351-2V and 351-4V. Fits any 1972-73 Mercury Cougar or Ford Mustang with original H or Q code 351C engines. The earlier bracket found on the 1971-72 cars will also work and is stamped slightly differently.Replaces Ford part number D2AZ-9728-A.
Availability: Out of Stock
Item #: 31324 -
This is for the person who does not want to modify the off-shore Mustang reproduction wheel lip mouldings we sell but do not have good cores for exchange for our premium set of restored wheel lips. Each one of these wheel lips will show some imperfections, mostly found on the inside where the wheel lip fastens to the wheel arch. The blems most commonly found on our less than perfect wheel lip mouldings may include multiple extra little holes drilled for mud flaps, "speckles" in the finish from...
Availability: Out of Stock
Item #: 42387 -
Rear driver side wheel lip moulding. Fits any 1971-73 Mercury Cougar.Replaces Ford part number D1WY-6529165-A.
Availability: Out of Stock
Item #: 31792 -
Restored passenger side (right hand) aluminum channel for installing the roof side, or upper door and quarter window weather stripping. Passenger and driver sides are contoured differently and are for the 1971-73 Mercury Cougar and Ford Mustang coupes only. These channels also have pre-drilled holes for installation and often times the assembly line workers 'made their own holes' so there often times will have additional assembly line holes. Plan on installing a new roof rail weatherstrip....
Availability: Out of Stock
Item #: 31791 -
Restored driver side (left hand) aluminum channel for installing the roof side, or upper door and quarter window weather stripping. Right and left sides are contoured differently and are for the 1971-73 Mercury Cougar and Ford Mustang coupes only. These channels also have pre-drilled holes for installation and often times the assembly line workers 'made their own holes' so there often times will have additional assembly line holes. Plan on installing a new roof rail weather strip. Shipping...
Availability: Out of Stock
Item #: 11201 -
Used half vinyl top roof trim from a 1971-73 Mercury Cougar for the passenger side. Half vinyl top option was a partial covered vinyl roof starting at the windshield and extending rearwards past mid-way on the roof. Not to be confused with the complete vinyl roof covering trim. Used trim will have minor wear, weathering, and generally be free of defects. This is a trim exchange, if you do not have an acceptable core trim piece, please purchase a core passenger vinyl half roof trim. Call...
Availability: Out of Stock
Item #: 11200 -
Used half vinyl top roof trim from a 1971-73 Mercury Cougar for the driver side. Half vinyl top option was a partial covered vinyl roof starting at the windshield and extending rearwards past mid-way on the roof. Not to be confused with the complete vinyl roof covering trim. Used trim will have minor wear, weathering, and generally be free of defects. This is a trim exchange, if you do not have an acceptable core trim piece, please purchase a core driver vinyl half roof trim. Call 503-463-1130...
Availability: Out of Stock
Item #: 42384 -
Front passenger side wheel lip moulding for any 1971-73 Mercury Cougar.Replaces Ford part number D1WY-16038-A.
Availability: In-Stock Item
Item #: 16747 -
REQUIRES sending your cores in advance.This is a restored aluminum 3 piece trim set from an early 1971 Mercury Cougar. Included are rear of hood trim Ford part # D1ZZ-16B918-A. Both fender trim pieces Replaces Ford part number D1WY-16C133-A and D1WY-16C132-A. Our restored aluminum trim is correctly bright dipped or anodized like originals.Technically these trim pieces were only used during the first 6 months of production on 1971 Mercury Cougar and all XR7 models including...
Availability: Out of Stock
Item #: 25379 -
Left side factory aluminum door guard.
Availability: Out of Stock
Item #: 15-0206 -
Used rubber bumper for the tilt column. 70 - 73 tilt columns require 3 bumpers, one on the lower and two on the upper knuckles. *NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year.
Availability: Out of Stock
Item #: 31282 -
Reproduction locking pawl for the 1970 - 1979 Mercury Cougar or Ford Mustang that is equipped with a factory tilt steering column. This unit works in conjunction with a pin and is responsible for locking the tilt column in place. In many cases, the pin tends to move out of place and break or chip the teeth of the locking pawl. We have found that 3 of 4 tilt columns that we have disassembled have locking pawls with broken or chipped teeth. Replaces Ford part # D0AZ-3B661-A. *NOTE*...
Availability: Out of Stock
Item #: 15-0153 -
This extension holds the inner spring tube in place on the 70 - 73 tilt column. Fragile piece, should take great care when tapping on this pot metal piece. Limited supply. Ford casting number: D0ZA-3790-*NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year. ...
Availability: Out of Stock
Item #: 15-0114 -
Ford part number 3E629. Molded rubber construction, fixed and tilt steering columns. These may have been used as early as late 1972, not sure. Limited stock. The reproduction plastic version for 1969-72 will also fit and work in conjunction with the available foam insulation. *NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year. ...
Availability: Out of Stock
Item #: 33191 -
Shift kit for the FMX transmission valve body for all 1969-72 and 1969-72 Mercury and Ford. This is a standard shift rebuilding kit for your stock valve body.* Note - 1973 has a different shift kit, see related items.
Availability: Out of Stock
Item #: 31238 -
Set of 6 new correct bolts for attaching the FMX transmission to 351 engines. Fits all 1967-73 Mercury Cougar and 1967-73 Ford and Mustang with transmission code X, or FMX automatic transmissions. Quality fasteners from AMK.
Availability: Out of Stock
Item #: 15-0163 -
Good used actuating rod for the ignition switch on the 1971, 1972 and 1973 Mercury Cougar or Ford Mustang. 8-1/8 inches on rod center long.
Availability: Out of Stock
Item #: 15-0169 -
This is a plastic cushion, washer and/or spring between the lower knuckle and inner tube on a 1968 - 1973 tilt-away steering column. These have a larger diameter than the 1967 plastic cushion.*NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year.
Spotlight!
Featured!
Availability: Out of Stock
Item #: 32366 -
NOS retainer / friction clips that replace broken injected plastic shaft retainers on fixed or tilt steering collapsible columns on most FoMoCo products starting in 1968 and through the 70's. These installs on the upper piece of what Ford called the Steering Column Shaft Assembly, also known as the inner steering column collapsible shaft. The Steering Column Shaft Assembly is the 2 piece shaft that connects the steering wheel to the rag joint. The upper piece of this shaft...
Availability: Out of Stock
Item #: 15-0196 -
1973 Complete, solid Mercury Cougar / Mustang tilt column with no missing or cracked parts. Rebuilt with the inclusion of a fixed lower shaft which eliminates the need for the hard to find (and expensive) tilt rag joint. No change to the installation, or function, and will be in stock more often than our full priced 1973 tilt column. Although they may look much alike, each year 1970 - 1973 is unique. Every column we sell has been disassembled and reconditioned by our full time in house tilt...
Availability: Out of Stock
Item #: 15-0197 -
This clip goes on the upper end of your column and keeps your steering shaft from moving around when you pull up on your steering wheel.See item 31804 for new clip.
Availability: Used / Wrecking Yard Item
Item #: 15-0200 -
Ignition housing / cover for the fixed steering column on 71 - 73 Cougars and Mustangs. Technically called a "Flange", the ignition cylinder sits inside this cover.This item will need to be re-painted to match your column.Ford Part number D0AA-3511-CW
Availability: Out of Stock
Item #: 15-0027 -
Good used turn signal stalk with no rust or peeling chrome. The 1970-73 with tilt column used a stalk with an additional plastic bushing near the base. This used unit is only for the person who cares about originality in the smallest of details as our repro is a decent piece, just not exact.*NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is the designer of all of our...
Availability: Out of Stock
Item #: 15-0107 -
Good used upper collar for the tilt column on the 1971, 1972 and 1973 Mercury Cougar or Ford Mustang.*NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year.
Availability: Out of Stock
Item #: 15-0057 -
Used upper steering column bearing for your 67 - 73 Cougar or Mustang. One required per car. Fixed Columns only use the upper bearing, while the tilt columns used an upper and lower. The used lower bearing can be found here. Outside diameter: 1 3/16 " * - may not fit some 67 Mustang applications with a fixed column as these used Ford part # C4OZ-3517-A, which is the same part used in the Fairlanes/Comets with a fixed column. To our knowledge this bearing is not currently reproduced. *NOTE* For...
Availability: Out of Stock, On Order
Item #: 33160 -
Replacement seal with boot for all 1969-73 FMX and 1967-73 C6 transmissions. Tail shaft and slip yoke seal.
Availability: Out of Stock
Item #: 15-0100 -
Steering column to steering box coupler, also known as a 'rag' joint. Used on 1971 1972 1973 Cougar tilt columns. Good used condition, supplied with one, 12 point attaching bolt. You will need to reuse one of your factory ones. Splined end slightly larger than previous years, due to the upgraded integral steering box unique to the later Cougars. This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in...
Availability: Out of Stock
Item #: 33173 -
Basic FMX transmission rebuild kit. Kit includes gaskets, seals, bands, filter, modulator, everything as shown. Fits all Ford FMX transmissions for any 1969-73 Mercury Cougar or Ford Mustang with that X code FMX transmission. Quality kit, same as supplied to professional shops.
Availability: Out of Stock
Item #: 33176 -
O Ring gasket for all automatic transmission dip stick tubes. Replacement gasket for C4, C6, and FMX trans dip stick tubes 1967-73 Mercury Cougar and Ford and Mustang.
Availability: Out of Stock
Item #: 25813 -
Correct for any 1967-73 Ford product with a tilt or fixed column. The repros are fine, but the end knob is distinctly different. Extremely difficult part to find in NOS form and very sought after. Keep in mind we also have excellent used pieces at a fraction of the cost. Ford part # D0AZ-13305-A.*NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is the designer of all of...
Availability: Out of Stock, On Order
Item #: 14200 -
Courtesy light door jamb switch with automatic seat back release option. Three pin switch not for use without seat back release. Additionally, this three prong switch was used on most 1970-76 Full and mid sized Ford, Mercury, and Lincoln. Some with or without the seat back release option. Replaces Ford Part #: D1AZ-13713-E and D0OZ-13713-A.
Availability: Out of Stock, On Order
Item #: 13135 -
Electronic voltage regulator for use on any 1967-73 Mercury Cougar or Ford Mustang or Ford. Same foot print as originals, cover can be swapped.
Availability: Out of Stock, On Order
Item #: 27461 -
This is a good used main power window wiring harness that passes through the firewall, travels along the passenger side engine compartment and mates the the rectangular power window relay. Fits 1971-73 Mercury Cougars with factory power windows. This is a Grade B harness that has been tested, inspected and repaired as needed. This harness will function properly, but will have some obvious repairs. We also sell a Grade A harness that will look much better for judging.Replaces Ford part number...
Availability: Out of Stock
Item #: 41020 -
Power window door and main harness from a 1973 Mercury Cougar or Ford Mustang. This driver side door harness has the power window plug, door ajar plug, and stereo speaker plug. Factory harness, the extra plugs were not used if you had a standard model or AM radio. Tested and inspected and ready to install. Does not include any of the other power window harness segments, i.e. passenger side door, rear windows, or under hood segments. Switches also not included. Does not fit 1972 or earlier...
Availability: Out of Stock
Item #: 12284 -
These are all new, not rebuilt, OEM Ford quality. We recommend these over the generic version and the "concours" version. Marked with Ford D2AF-11450-AA part number, but is functionally correct for all 1967-73 Cougars. Black case as original.Replaces Ford Part #: C7AF-11450-A1 , B6AZ-11450-A , C7AZ-11450-A , D2AF-11450-A , etc
Availability: Out of Stock
Item #: 10048 -
NOS master power window switch for 1973 Cougars and Mustangs. Five switch assembly - driver / passenger front and rear windows, and a master lock out switch. This is a service replacement master switch, the buttons are more rounded than the 1973 version. Still all works the same. NOS E0VY-14529-C.
Availability: Out of Stock
Item #: 54890 -
Used grade "B" power window master switch bezel. One year only bezel for the Cougar. Fair used part with woodgrain appliqué in place and pitted chrome. Ford engineering # D2AB-14527-A.
Availability: Out of Stock
Item #: 14159 -
Used grade "A" power window master switch bezel. One year only bezel for the Cougar. Good used part with woodgrain appliqué in place and good chrome.Ford engineering # D2AB-14527-A.
Availability: Out of Stock, On Order
Item #: 13844 -
Reproduction 4002 incandescent (non-halogen) low beam light bulb for the 1967, 1968, 1969, 1970, 1971, 1972 and 1973 Mercury Cougar. Plugs right in to the factory 3-prong plug and mounts in the outboard position on the car.These are close to OEM wattage (37.5 / 60 watt, OEM was 37.5 / 50 watt) to work with the factory headlight switch, without adding any relays like you would for higher wattage halogen bulbs.Ford Bulb #: 4002, Aftermarket Bulb #: 4000. Sold individually, 2 required per car. ...
Availability: Out of Stock, On Order
Item #: 31714 -
Reproduction driver side drum brake spindle. These are getting hard to find in used condition, considering the after market disc brake conversions that require the use of 1970 drum brake spindles. 1970 was a heavier design over 1968-69. Fits 1970 - 1973 Mercury Cougar, Ford Mustang, and mid sized Ford's such as Torino, Ranchero, Cyclone, etc.
Availability: Out of Stock
Item #: 31946 -
Reproduction pair of drum brake spindles. These are getting hard to find in used condition, considering the after market disc brake conversions that require the use of 1970 drum brake spindles. 1970 was a heavier design over 1968-69. Fits 1970 - 1973 Mercury Cougar, Ford Mustang, and mid sized Ford's such as Torino, Ranchero, Cyclone, etc.
Availability: Out of Stock
Item #: 14126 -
Replacement lamp for the speedometer, heater controls, ashtray, automatic shift indicator, low fuel, seat belt reminder, or emergency flasher warning lights on the visual check panel.
Availability: Out of Stock
Item #: 10742 -
Used brake pedal for the Mercury Cougar or Ford Mustang equipped with an automatic transmission and drum brakes. This is a short style pedal is for cars with four wheel manual drum brakes and is shipped bare.Ford part # D1ZZ-2455-C.