Your cart is empty!
Our shopping cart requires the use of cookies. If you have your cookies disabled, please enable them for our site to place an order. If you have cookies enabled and have added an item to your cart, but you are still seeing this message, that could indicate that the cookie for our shopping cart is corrupted on your computer.You should be able to fix this by either:
Buy Details
Complete set of front seat belt bolts for your 67 - 68 Cougar or Mustang. Included are the 4 bolts, 4 large washers, 2 spacers and 4 rubber anti-rattle gaskets. Get the rear set here.
Complete set of rear seat belt bolts for your 67 - 68 Cougar or Mustang. Included are the 4 bolts and 4 spacers. Get the front set here.
Fits 1968 Standard or XR7
Fits 1967 - 1973 Standard or XR7. Pins not used on 71-73 buckets.
Fits 1968 - 1970 Standard or XR7
New 8-32 set screw for the rear window crank handles. Fits 1968-70 Mercury Cougar and Ford Mustang. Allen hex size of 5/64".
Missing some of the hardware used to bolt on your shock tower braces? Here are our reproduction shock tower brace mounting kit for the Mercury Cougar or Ford Mustang.
Driver side bracket that fits onto the rear radio bracket assembly on the 67 - 68 Cougar or Mustang equipped with a console. The bracket assembly is 3 separate pieces, this is for the driver side bracket only.
Passenger side bracket that fits onto the rear radio bracket assembly on the 67 - 68 Cougar or Mustang equipped with a console. The bracket assembly is 3 separate pieces, this is for the passenger side bracket only.
This kit is similar to the original type mounted in every drivers side door. These OEM style Riv-Nuts will be a challenge to install unless you have the special tool. Almost every body shop will have this rivet gun type of tool but here are a couple of ways to tackle the installation without the correct tool. Hole size is 1/4". Replaces Ford Part #: C7AZ-17696. Check out our video below for more info on mirror installation: Still have riv-nut questions? Here are riv-nut answers! ...
Reproduction Smog Pump Pully Bolt for the 1967 - 1968 Mercury Cougar or Ford MustangSold individually
Keeps spark plug wires neat and orderly. Mounts on valve covers. Replaces Ford Part #: B8Q-12297-A.
Made of heat resistant black nylon. Keeps spark plug wires neat and orderly.
This clip holds the speedometer cable gear to the end of the cable. Replaces Ford Part # : C1DZ-17292
These brackets are intended to make sure that the brake pads and the caliper stay in the correct alignment, as well as for anti-rattle. Replaces Ford Part # C8OZ-2B295-A. Sold individuallyCheck out our caliper tips and tricks video below: ...
Sold individually. Zinc Dichromate (yellow-rainbow)
Reproduction dark zinc starter bolt for the Mercury Cougar or Ford Mustang equipped with the small block engine. These units are sold individually.
Fits Standard and XR7
Universal wire loom plastic clip for any application on Cougars or Mustangs, as well as many other models.5" x .26"
This nut fits onto the strut brace at the front of the car, and not the control arm end. It is the lock nut that goes on after the the bigger strut rod bushing nut.Replaces Ford part # 340460-S
Stud for attaching heat shield to passenger side exhaust manifold. Fits all 1968 Mercury Cougar or Ford Mustang and other Ford too. Sold individually. Phosphate & Oil (gray-black)
Stud for attaching exhaust manifold heat shield on passenger side. Sold individually Phosphate & Oil (gray-black) Replaces Ford Part # 382338-S
Stud that screws directly into the 289 exhaust manifold on most 1965-67 Ford 289 engines, including Mercury Cougar and Ford Mustang. Sold individually Zinc (dark silver)
New blue removable strength thread locker for your project. This is a must have item if you are reassembling your pride and joy after restoration or just changing out parts. Often times, the vibrations from these antiques can vibrate loose the fasteners used to hold it together. If you use this, you can rest assured that your Merc or Ford will not fall apart from fasteners that have vibrated loose.
New red permanent strength thread locker for your project. This is a must have item if you are reassembling your pride and joy after restoration or just changing out parts. Often times, the vibrations from these antiques can vibrate loose the fasteners used to hold it together. If you use this, you can rest assured that your Merc or Ford will not fall apart from fasteners that have vibrated loose.
Sold individually Zinc (dark silver)
1967-68 XR7 over head console pad clip. Two needed per car. Sold individually # C3AB-63519A16
Seven (7) of these acorn nuts are used to hold the trunk trim moulding on to the trunk. Replaces Ford Part # 377767 For more insight on this tricky trunk trim, check out our video below: ...
Replacement U-nut or clip for any 1967-70 Mercury Cougar trunk lid. These slide into the bottom of the trunk lid for attaching the hinges. Correct 5/16-18 threads, 7/8" from center of hole to edge. 4 total per trunk lid, sold individually.
9" inside the arch to the end of the threads. Thread size 7/16-20, includes tall nuts as shown. Concours Grade 5 flange nuts available separately, see related items.
Sold individually, two per side, four per car required. These often get destroyed when you go to replace your door window regulator slides. Two of these are used to install the C7ZZ-6523288-A track. Check out our handy diagram below to find other '67-'68 door parts you may need. All the item numbers shown can be typed in to the search bar on our site. (Click image to view full size)Not sure where to begin when it comes to replacing your window regulator? Check out our how-to video...
Almost identical to the original, tab is a bit longer. *NOTE*1969 Cougar owners do not need this part as it is built in the the chromed plastic, rectangular bezel on the door panel.
Used on all four 1967 belts for a total of 8 per car. Found to be slightly dished on most examples we see.
This is the rubber spacer / washer that goes between the bolt head and the metal washer of your seat belt hardware. The purpose of the rubber washer is to dampen any vibrations caused by the movement of the seat belt.Sold individually# 354959-S
Reproduction steering gear or seat belt washer for the Mercury Cougar or Ford Mustang. These units are sold individually.Replaces Ford part # 378580-S.
Used on the retractors.
These spacer / washers were used on the rear belts of 1968 - 1973 Cougars. 1968 used two per bolt for a total of eight, 69-71 used one per rear belt for a total of four and 72-73 used one per belt on the inner only as the outer belts had a re-tractor in the rear 72-73. They were red to guide the line workers on placement.
These spacer / washers were used on the rear belts of 1968 - 1973 Cougars. 1968 used two per bolt for a total of eight, 69-71 used one per rear belt for a total of four and 72-73 used one per belt on the inner only as the outer belts had a re-tractor in the rear 72-73. They were red to guide the line workers on placement. Sized like the originals, but do not have the dimples all over. 0.53" ID x 0.88" OD.
Same as 69-73 but with no markings.
Sold individually, phosphate & Oil (gray-black).
Reproduction Wire Loom Mounting Kit for the 1968 Mercury Cougar / Ford Mustang
Master clip kit which includes the following fasteners:Engine bayEngine feedFirewallFront crossmemberParking lightsPassenger side apron below relayRadio cable to dashKeep in mind that not all fasteners found on 1967 Courgars / Mustangs are in this kit.
Master clip kit which includes following fasteners: Driver side apronEngine feedFirewallFront crossmemberGas tank senderHorns and regulatorPassenger side apron below relayRadio cable to dashKeep in mind that there are many other fasteners on 1968 Cougars / Mustangs that are not in this kit.
Reproduction XR7 Console Fastener Kit for the 1967 and 1968 Mercury Cougar
New black oval Phillips headed screws with correct sized heads for seating into the original and reproduction 1967 XR7 rocker hash marks.
[No Description Provided]