Your cart is empty!
Our shopping cart requires the use of cookies. If you have your cookies disabled, please enable them for our site to place an order. If you have cookies enabled and have added an item to your cart, but you are still seeing this message, that could indicate that the cookie for our shopping cart is corrupted on your computer.You should be able to fix this by either:
Buy Details
This is the "Chrome" trim across the top of the windshield on the inside. This piece will need to be sandblasted and repainted. Many people have chromed these, but because of Federal safety regulations from the factory they were painted satin silver.Ford Part Number: D1ZZ-7603606-A.
Our core aluminum rear window mouldings / trim will have scratches and dings and are suitable for restoration. This kit consists of one driver side (left hand) upper, one passenger side (right hand) upper, one driver side lower, and one passenger side lower core window moulding / trim. These original FoMoCo mouldings are far superior to the off shore reproductions that do not fit well and have an incorrect color to them. We will not send you kinked or gouged trim as it is not feasible to...
Reproduction four piece aluminum rear window moulding / trim set for the 71 - 73 Cougar or Mustang. Customers have mentioned that these are very hard to install on the Cougar. Ford part #s D1ZZ-6542405-A, D1ZZ-6542404-A, D1ZZ-6542430-A, D1ZZ-6542431-A.
Restored four piece aluminum rear window moulding / trim set correctly restored with an anodized and a bright dip finish and polished to a very high luster.Ford part #s D1ZZ-6542405-A, D1ZZ-6542404-A, D1ZZ-6542430-A, D1ZZ-6542431-A.
Good used four piece aluminum rear window moulding / trim set with some dings and or minor scratches. Ready to install on your Cougar as is, or polish them to be installed on a daily driver. These original FoMoCo mouldings are far superior to the off shore reproductions that do not fit well and have an incorrect color to them. Ford part #s D1ZZ-6542405-A driver side (left hand) lower, D1ZZ-6542404-A passenger side (right hand) lower, D1ZZ-6542430-A passenger side upper, and D1ZZ-6542431-A...
NOTE: Some modification required to fit Cougars! These are actually 69-70 Mustang wheel lip mouldings, which have a different shape / contour. However, with a bit of massaging they can be made to fit the 71 - 73 Cougar. They are the closest alternative we have found that fits and looks reasonably good for much less than restored originals. Check out our video below, showing how easy it is to install these mouldings on a Cougar ...
Original sway bar mount for your 1971-73 Mercury Cougar or Ford Mustang. Nice original, removed from our better cars. Metal cleanup needed, we cut these a little generously to protect the bracket. Original part number is 5A483. The MPC and other manuals refer to this bracket as: reinforcement and mounting bracket for front stabilizer bar. One per side, right and left are the same. See related items.
According to the MPC 1970 primarily, a few 1971-1973's. If you have a hardtop or coupe, (VIN numbers starting with either 0F91 or 0F93) and standard wheels with hub caps. Or, any 1971 - 1973 with style steel wheels. Total length is 6-1/4 inches, with 4 inches being threaded. Threads 1/2-13. We find this bolt to only have 2 1/2" of threads. More data is needed as the MPC is not reliable on these items. What do you have in your trunk? We want to know! Search words 70 71 72 73 1972
1971 - 1973 Mercury Cougar hard tops and coupes with regular steel wheels and hub caps. J bolt total length listed in MPC is 8-3/4 inches, with 6-1/2 inches threaded on the straight end but we find the actual length to be 10" long with about 4" of threads. We also see this used with the 1971 - 1973 Kelsey Hayes Styled Steel wheel even though the MPC lists another size. There are absolutley to absolutes when it comes to items like these and what Ford "may" have called for. Would love to hear...
Cast iron pedestal mount for the air conditioning compressor on all 1970 - 1973 Mercury Cougars and Ford Mustangs with the 351C engine, both the H code 351-2V and M code 351-4V engines. Ford MPC part # D0ZA-2882-C.
Used alternator mounting bracket for any 1970-73 Mercury Cougar, Ford or Ford Mustang with 302, 351W, or 351C engines. Replaces Ford part number D0OE-10156-A.
D0DZ-9D664-B Bracket for mounting the charcoal canister to the body.
C8OZ-2B293-A Driver side caliper mounting bracket, also called a caliper anchor bracket in the Ford Master Catalog.Check out our caliper tips and tricks video below: ...
C8OZ-2B292-A Passenger side caliper mounting bracket, also called a caliper anchor bracket in the Ford Master Catalog.Check out our caliper tips and tricks video below: ...
Bracket mounts to top of stock cast iron Cleveland intake manifold, holding the throttle cable. Used on both the 351-2V and 351-4V engines with original Ford cast iron intake manifolds. There are two versions of this bracket per the MPC, it is such a minute detail, it is hardly worth listing separately.Replaces Ford part number D1ZZ-9728-E and D1AZ-9728-H.
Original FoMoCo used two speed windshield wiper motor mounting bracket for your 1971-73 Mercury Cougar or Ford Mustang. This used bracket comes with grommet for all 1971-73 Cougar and Mustangs. Ford part # D1ZZ-17496-B.
Sold as a pair. One long and one short bracket. Fits 1971-73 Mercury Cougar and Ford Mustangs that have original style radiators. Mounting bolts not included. Replaces Ford part number D0OB-8B359 RH, and D0AB-8K007 LH. Check out our video on Radiator and Fan upgrades below: ...
Sold as Set of Four, two lower, two upper.
This kit includes the 4 fine threaded "T" shaped studs (with nuts) that mount the backing plate to the spindle and the plate that goes on the inside of the backing plate. These are used parts that are not damaged or corroded, taken from a Western parts car.
Nut for attaching brake boosters in any 1967-73 Mercury Cougar or Ford anything, including Mustang. 3/8 - 16 zinc plated nut with serrations.
Locking nut that attaches the shift lever to the shifter arm and support inside the shifter buckets. We normally see the course threaded nuts on the 1971-73 shifters. Please check your shift arm support for correct threads. Check out our video on rebuilding your shifter below: ...
Replaces Ford part # 55806-S
Reproduction side view mirror screw. These screws are sold individually. Do you have riv-nut questions? Here are riv-nut answers!
Unique shouldered screw that keeps your switch in perfect alignment, using incorrect screws will damage the switch.Fixed columns require 3 screws. Tilt columns require 2 screws. *NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is the designer of all of our solid state sequential systems. There is no question he cannot answer! Here is a link to a great source of...
1/4-20x1 inch stud. Sold individually. Found on various years and parts of Cougars. Used for attaching 1967-68 grilles to the headlight buckets. Also as replacement mounting studs for front and rear fender and quarter extensions. Zinc Dichromate (yellow-rainbow)
10 of these are used to mount the 1968-71 Cougar hood scoop found on the 68 428 CJ, 1969-70 Eliminator, 1969-70 428 Ram Air equipped Cougars, and 1971 GT and 429CJ. Sold individually Zinc (dark silver).
Door window glass grommet or washer to protect the glass for the Mercury Cougar or Ford Mustang. These units are placed under the bolts for mounting the window stops and the channel bracket. Used on most full and mid sized Ford
The first in a series on production facts, this handy volume examines seven years of data from just about every imaginable statistical angle! Ever wonder how many cars were painted like yours? How about the rarest paint & trim combination...or the most common? You'll find those tidbits and many more, as we show you the figures for: * exterior color * interior trimset * color and trimset * engine * transmission * engine and trans. This book also provided the total production for RPOs -...
[No Description Provided]
Replaces Ford Part # 381985-S Sold individually
Bumper bolt nuts sold individually. Also available in our bumper bolt kit.Please know that chrome cracking from the installation of bumper bolts on our rechromed bumpers is not covered under warranty. We have observed that some reproduction wavy washers are of a thicker material than original and require more torque to flatten out properly for a good fit. We suggest that no matter what thickness your repro wavy washer is that you flatten them out in a vise prior to installation so as not to...
383278-S 1/4-20 Nut with spinning or captured washer, sometimes called a swivel nut, for attaching various door window components for 1970-1973 Cougar and Mustang bolt-in door glass. This nut was used to fasten the guides into the 1970 bolt in glass. Additionally this nut was used for attaching the window channel bracket to door and quarter glass on the 1971-73 Cougar and Mustangs. This is a new or reproduction part from AMK.
383278-S Nut with spinning or captured washer, sometimes called a swivel nut, for attaching various door window components for 1970-1973 Cougar and Mustang bolt-in door glass. This nut was used to fasten the guides into the 1970 bolt in glass. Additionally this nut was used for attaching the window channel bracket to door and quarter glass on the 1971-73 Cougar and Mustangs.
Reproduction exhaust pipe to exhaust manifold nut for the Mercury Cougar or Ford Mustang and they are sold individually.Ford part # 376420-S.
Used bezel retaining nut for the headlight switch on any 1971-73 Mercury Cougar or 1971-72Ford Mustang. These are much better quality than those found in the 1969-70 cars. Good threads and very good chrome on the front as shown. Check the length for the 1973 Ford Mustang, we've had an owner that found one to be over 2 inches in length. Unfortunately, we do not have the longer length version.Replaces Ford part number D1ZB-11650-BA.
Reproduction exterior convertible boot moulding / trim nuts for the Mercury Cougar or Ford Mustang and Torino. Here's another great reproduction brought to you by WCCC! Each vehicle will require 20 nuts. Sold individually.
Reproduction nut that replaces Ford part # 34033-S. This is the nut that secures the pitman arm to the steering box. Has correct 7/8"-14 threads. Split washer also needed, not included, nut only.
This is our reproduction quarter panel extension nut for the Mercury Cougar or Ford Mustang. These are sold individually.Replaces Ford part # 373556-S. Fits: 1967 Mercury Cougar1968 Mercury Cougar1969 Mercury Cougar1970 Mercury Cougar 1967 Ford Mustang1968 Ford Mustang1969 Ford Mustang1970 Ford Mustang ...
Replaces Ford part # C2DZ-6A529 Sold Individually.
Course threaded nut for most 1969-73 automatic shift arms. This is the nut that sticks down from the bottom of your automatic floor shifter and the nut connects the shift rod that goes to your FMX transmission. 3/8-16 locking flange head nut.
Perfect fit.
Correct nut that is designed not to come undone.
New torque converter nuts for connecting torque converters to flex plates on 1967-73 Mercury Cougar or 1967-73 Ford Mustang or other Ford Lincoln Mercury that is not metric. 3/8-24 threads, Grade 8 nut with a 9/16 inch hex. 0.79" OD and 0.39" thick. Torque converters use 4 nuts for attachment.Ford number 377704-S
Used bezel retaining nut for the windshield wiper switch on any 1971-73 Mercury Cougar or Ford Mustang. Good threads and very good chrome on the front as shown. Replaces Ford part number D1ZB-17512-A.
380771-S100 Good original used nut and washer for mounting all pitman arms. Has correct 7/8"-14 threads. Ford master part number for the washer is 34814-S.
Set of 4 reproduction torque converter nuts for the Mercury Cougar or Ford Mustang.
Nuts and washers for attaching the rear differential carrier or pumpkin or third member to the rear axle housing. Correct for all 1969-73 Mercury Cougar and 1969-73 Ford Mustang. 8 inch or 9 inch third members, all the same.
Correct size and style white square plastic insert that clips onto front or rear license plate bracket on any 1967-73 Mercury Cougar. Each kit allows one license plate to be mounted. The actual screw has a large head which is made for license plates, but is not the factory Ford style of fastener for Concours judged cars. We also sell an accepted original style of screw, see item 8286.