Your cart is empty!
Our shopping cart requires the use of cookies. If you have your cookies disabled, please enable them for our site to place an order. If you have cookies enabled and have added an item to your cart, but you are still seeing this message, that could indicate that the cookie for our shopping cart is corrupted on your computer.You should be able to fix this by either:
Buy Details
Premium reproduction, near concours correct front emergency / parking brake cable for the Mercury Cougar or Ford Mustang. This cable hooks onto your inside foot activated brake assembly inside the car, through the floor board, and hooks to the brake equalizer cable under the car. This unit is very close to an OEM replacement, much better than our economy cable. ...
This used emergency / parking cable anchor bracket is spot welded to your passenger side (right hand) front floor pan and anchors the cable. Comes "as taken from parts car". *Customer Feedback* from mercurycougar.net: "Best guys to always talk to about Cougars..will take the time on the phone with you, call you back if you leave a message, got all the time in the world for you when your talkin 'cause your important to them. Greatest thing for our hobby. Thanks Lin and Don for making/getting...
Reproduction concours correct premium grade passenger side (right hand) emergency / parking brake cable for the 1970-73 Mercury Cougar and Ford Mustang with V-8 engines. This is the long one on the passenger side (right hand) and measures approximately 133-1/8 inches long.
Reproduction emergency / parking brake cable for the Mercury Cougar or Ford Mustang with V-8 engines, that is approximately 133 1/8" long. This unit fits from equalizer to rear brakes and one is required per vehicle.Replaces Ford part # D0ZZ-2A635-A.
Premium grade reproduction driver side (left hand) rear emergency / parking brake cable. This is the short one, 31 inches, located on the driver side and is an exact fit for 1970 - 1973 Mercury Cougar and Ford Mustangs. Ford Part # D0ZZ-2A635-B
Front emergency brake cable bracket that welds to the floor under the drivers side floor board. It is spot welded to the floor pan and frame rail and is often over looked when floor pans are replaced. The unit you receive will need clean up, but will not be heavily rusted. Fits all 1969-70 Mercury Cougar and Ford Mustang.
This used emergency / parking brake cable equalizer mounts to the end of the parking brake release assembly and captures the emergency brake cable. Replaces Ford part # C6OZ-2A602-A.
Keeps proper tension on emergency / parking brake cable by taking up the slack when the brake is off. Hook attaches to the bracket under the passenger side floor. Replaces Ford Part # C7ZZ-2A808-A.
Keeps proper tension on emergency / parking brake cable by taking up the slack when the brake is off. Hook attaches to the bracket under the passenger side floor. Replaces Ford part # C7ZZ-2A808-A.
Reproduction disc brake caliper insulators for a large array of FoMoCo products starting in 1968. 2 are required per caliper, 4 total per vehicle. Sold as a pair. Replaces Ford part # C8AZ-2B299-A.Check out our caliper tips and tricks video below: ...
Each kit contains the seals for one caliper assembly. Replaces Ford Part #: C8ZZ-2B120 and #C8ZZ-2B121Check out our caliper tips and tricks video below: ...
Reproduction disc brake master cylinder cap in gold cadmium for the Mercury Cougar or Ford Mustang. We have compared this cap to our originals, and the stamping does not match any of our originals, but the manufacturer claims that the scripting is correct. Also available in chrome! This cap will only fit master cylinder part# 15298Replaces Ford part # C7AZ-2162-B. Fits: 1967 Mercury Cougar1968 Mercury Cougar 1969 Mercury Cougar 1970 Mercury Cougar 1971 Mercury Cougar 1972 Mercury Cougar...
Reproduction premium quality disc brake master cylinder cap for the Mercury Cougar or Ford Mustang. These are considered concours correct and show quality. Check out the link below for some information on master cylinder caps: http://anghelrestorations.com/uploads/3/5/1/2/35122002/master_cylinder_caps_1.5.pdf Replaces Ford part # C7AZ-2162-B. Fits: 1969 Mercury Cougar1970 Mercury Cougar 1971 Mercury Cougar 1972 Mercury Cougar 1973 Mercury Cougar 1969 Ford Mustang / Torino1970...
Reproduction chrome master cylinder cap for the Mercury Cougar or Ford Mustang equipped with drum brakes. This quality reproduction has the correct lettering and is correct for 1970-73 Cougars and Mustangs. However, it fits and looks good on all 1967-73 Cougars and Mustangs with other under hood chromed goodies. Will also work fit any other 1967-73 Ford drum brake dual reservoir master cylinders.Replaces Ford part # C7AZ-2162, C9AZ-2162, and D3AZ-2162.*Customer Feedback from Mercurycougar.net*"...
Correct check valve for both power drum and power disc brake cars. Comes with grommet.
Clip or X-washer for attaching the emergency brake lever inside the rear brake drum. Fits 8 and 9 inch rear axles. Literally used on most all Ford products from 1965-73 and likely beyond. Also called a retainer for the parking brake lever pin. The long ears get squeezed with a good set of pliers for attaching. Replaces Ford number 91A-2106.
Exact copy of the hard to find original. This two piece clip is used to mount gas and/or brake line to floor pans.
Complete reproduction front drum brake spring kit for Ford Mustangs equipped with 9" drums. This kit contains all the replacement springs and hold downs required to do a professional brake job on front drum brakes. Kit includes enough parts for two wheels.
Reproduction Convertible Brake & Fuel Line Clamp Kit for the 1970 Mercury Cougar - 1970 Ford Mustang
Copper crush washer for all disc brake hoses and calipers 1968-73 Mercury Cougar and Ford cars like Mustang. Size 0.39" x 0.62" x 0.062". Four needed per car, two per side (one on each side of the disc brake hose end) sold indiividually.
Parking brake return spring cup for the 69 - 73 Cougar or Mustang. This cup sits at the end of the spring and is held in place by an adjusting nut. It's used to keep the spring from sliding off of the front emergency / parking brake cable.
Reproduction seal for the lid of the brake fluid reservoir for a power disc brake equipped Mercury Cougar or Ford Mustang.Fits: 1967 Mercury Cougar1968 Mercury Cougar 1969 Mercury Cougar 1970 Mercury Cougar 1971 Mercury Cougar 1972 Mercury Cougar 1973 Mercury Cougar 1967 Ford Mustang1968 Ford Mustang 1969 Ford Mustang 1970 Ford Mustang 1971 Ford Mustang 1972 Ford Mustang 1973 Ford Mustang ...
Reproduction rubber seal for the top of the brake fluid reservoir on the drum brake equipped Mercury Cougar or Ford Mustang. Also fits 1967-71 Ford or Mercury full and mid sized cars, and 1970-73 Maverick and Comet. Replaces Ford part # C9AZ-2167-B.
STOPFLEX?? incorporates a special 4 layer design for superior strength and virtually no volumetric expansion. It starts with a Teflon PTFE core (liner) which is wrapped first in a Kevlar braid, followed by an elastomer barrier and then it's strengthened further by the outer stainless steel braid. Replacing original equipment rubber hoses with STOPFLEX?? stainless steel braided hoses will increase braking performance by doing away with the soft spongy brake pedal. Rubber hoses expand, with the...
This kit is a must when redoing the disc brakes on a 1968-73 Cougar. Includes new brakets (caliper stabilizers), bolts, pins, and clips and rubber dust seals. Kit includes the pair.Check out our caliper tips and tricks video below: ...
Reproduction disc brake master cylinder cap for the Mercury Cougar or Ford Mustang. This unit has the correct stampings, rubber inner gasket, and is considered show quality. This cap will only fit master cylinder part # 15298.Replaces Ford part # C7AZ-2162.Fits: 1967 Mercury Cougar1968 Mercury Cougar 1969 Mercury Cougar 1970 Mercury Cougar 1971 Mercury Cougar 1972 Mercury Cougar 1973 Mercury Cougar 1967 Ford Mustang / Torino1968 Ford Mustang / Torino 1969 Ford Mustang / Torino 1970 Ford...
Reproduction adjustable disc brake push rod set for the Mercury Cougar or Ford Mustang. When you convert to manual disc brakes, this kit eliminates excess pedal travel and insures quicker braking response. NOT for power disc brakes. For Manual disc brake cars ONLY.
This is a much needed part for your disc brake car. It is the correct Proportioning Valve Distribution Block for a 1970-71 Torino, Cyclone, Ranchero, 1970-73 Mustang and Cougar, but can be used on any year with minor brake line changes. Unlike the earlier units the proportioning valve is located internally. Keep in mind we do have a rebuild kit for your original unit so if you have an original FoMoCo block it is a better idea to rebuild it. NOTE! The feedback on this item is that one of the O...
D0OZ-2B257-C Disc brake distribution block for 1970 through 1973 Cougar and Mustang with factory disc brakes. Mounts to the driver side fender apron with two nuts. Bare block without brake switch. Will need a rebuild kit installed prior to using. Ford casting number D0OA-2B328-D *NOTE* Starting in 1970 there was a built in proportioning valve. **NOTE** Sometime during the 1972 model year there was a change to a D2ZA-2B328-AA casting number distribution block. Here’s a video to help...
Kit for rebuilding your drum brake distribution block for Mercury Cougar and Ford Mustangs. Special O-rings are made from EPDM (Ethylene Propylene 70 Durometer) which is specifically designed to withstand chemical degradation caused by prolonged exposure to brake fluid.Here’s a video to help you rebuild the distribution block so that you can corral your Cat or Pony without fearing for your life. ...
Reproduction driver side concours correct vented dust shield for the 69 - 73 Cougar or Mustang. Painted and ready to bolt on.Side specific.
Reproduction passenger side concours correct vented dust shield for the 69 - 73 Cougar or Mustang. Painted and ready to bolt on.Side specific.
Reproduction emergency / parking brake cable return spring that goes underneath the car for the Mercury Cougar or Ford Mustang.
Reproduction emergency / parking brake assembly for the Mercury Cougar that is sold as a complete assembly. These units do look way better than our used crusty originals, but they will never hold up as well as original FoMoCo!Replaces Ford part # D0ZZ-2780-A
Reproduction parking brake lever that mounts between the parking brake cable and secondary brake shoe in your rear brake drum assembly. 1967-73 Mercury Cougar or most Fords including Mustang. Fits 10 inch drum rears. Replacement part number for LH or DRIVERS side original part Ford number is C9ZZ-2A638-A.
Used parking brake lever that mounts between the parking brake cable and secondary brake shoe in your rear brake drum assembly. Ford service replacement part number for LH or driver side is C9ZZ-2A638-A. This unit is from a solid Western parts car, so you won't be getting one of those rusty East Coast units! Ford part # C9ZZ-2A638-A.
Reproduction parking brake lever that mounts between the parking brake cable and secondary brake shoe in your rear brake drum assembly. 1967-73 Mercury Cougar or most Fords including Mustang. Fits 10 inch drum rears. Replacement part number for RH or passenger side original part Ford number is C9ZZ-2A637-A.
C9ZZ-2A637-A Parking brake lever that mounts between the parking brake cable and secondary brake shoe in your rear brake drum assembly. Ford service replacement part number for RH or passenger side is C9ZZ-2A637-A. Clean Western part with no heavy corrosion like you see on Eastern cars.
Reproduction 10" parking brake link. Spring included. Sold individually, two per car. Replaces part Ford Number C2OZ-2A642-A
Parking brake link. The spring (not included) is wound in a rectangular shape to fit the one end of the link. Ford part # C2OZ-2A642-A.
Cork gasket for the disc brake splash shield. Fits all 1968-73 Mercury Cougar and Mustang and 1968-71 Ford mid size including Torino, Cyclone, Ranchero, Fairlane.Replaces Ford part number C8OZ-2B160-A.
Reproduction grease cap for front wheels of the Mercury Cougar or Ford Mustang. 2 Required per car, sold individually. Replaces Ford part # B5A-1131.
This is a front brake grease dust cap tool. No more dented caps. These are milled from 6061 solid aluminum.
Brake line rubber grommets for any 1967-73 Mercury Cougar or Ford Mustang. These are the ones that go through the shock towers for the front brake lines. Drum or disc, all the same. Sold as a PAIR. Ford number 373624-S.
Pair of steel brake line rubber grommets for any 1969-70 Mercury Cougar or Ford Mustang. These grommets go into the shock towers. Sold as a pair. Inside hole diameter is 3/16"
New hairpin clip for attaching the brake light switch to the brake pedal. This clip was also used to attach the clutch rod to the clutch pedal on manual transmission cars. Fits all years 1967-73, Ford and Mercury.Replaces Ford part number 380699-S.
Reproduction brake booster hose for Mercury Cougar or Ford Mustang. Measures 12" long
Reproduction hose and clamp kit for the brake booster on the 1970 Cougar or MustangDate code 10/22/69