Your cart is empty!
Our shopping cart requires the use of cookies. If you have your cookies disabled, please enable them for our site to place an order. If you have cookies enabled and have added an item to your cart, but you are still seeing this message, that could indicate that the cookie for our shopping cart is corrupted on your computer.You should be able to fix this by either:
Buy Details
Plain head, fine thread. Not concours, but meets or exceeds original specs. Sold individually.Ford part # 380328-S.
Phosphate & Oil finish. Sold individually. Replaces Ford part #: 378782-S
Sold individually, pivot stud for the aluminum power steering pump mounting bracket. fits all applications for small or big block. Also used on the 1970 Mercury Cougar with 428CJ. Phosphate & Oil (gray-black)
replaces Ford part # B-12764
Rear valance and 1967-70 windshield defroster attaching hardware. Sold individually. Zinc (dark silver)
Front retractor bolt, used in conjunction with two rubber spacer / washers and one washer. The two rubber washers go on either side of the re-tractor mounting hole and the metal washer is against the inner rocker.
Front inner bolt that attaches female portion of the lap belt to the transmission tunnel. Used in conjunction with a silver, fat washer that is slightly cupped.
Used early version of the long seat belt bolt for the Mercury Cougar or Ford Mustang. This early version has faint markings on the head of the bolt as where the later versions have more prominent markings. 13/16" hex head, two inch bolt with a 1/2 inch shoulder. Can be either smooth headed or have an "E".
Used early version short seat belt mounting bolt to mount the front retractor to the inner rocker panel and used in conjunction with a large washer. This is an early version of the the seat belt bolt with faint or no markings on the head, the later versions are longer, and have much more prominent head markings.13/16" hex head, 1-1/8inch bolt with a 3/16 inch shoulder.
Reproduction water pump bolt for the Mercury Cougar or Ford Mustang equipped with the small block engine. These are zinc (dark silver) plated and sold individually. This bolt is approximately 2-5/8" to the shoulder and an approximate overall length 2-3/4".
Replaces Ford part # 45964-S Sold individually
Reproduction steering gear box bolt. Sold individually
Reproduction water pump / timing chain cover for the Mercury Cougar or Ford mustang equipped with the 289 engine. This bolt has an approximate length of 2" to the shoulder and an approximate overall length of 2-1/4".
This is longer of the two with the + on the bolt head.
This is the shorter version of the top-loader with no "+" on the head. Sold individually
part# 372821-S
Reproduction Upper Control Arm To Shock Tower bolt. Sold individually. Replaces Ford part # 38049-S
NOS water pump bolt for the Mercury Cougar or Ford Mustang. This bolt is approximately 3-1/2" to the shoulder and an overall approximate length of 3-3/4".Replaces part # 376258-S.
Ford part #300958-S Sold individually
part # C9ZE-6345-A. Used on 289 / 302 / 351w 7/16" by 3" shaft. Sold individually
Four required per seat, eight per car equipped with bucket seats. Actual bolt length is 1-1/2 inches.Sold individually.
Alternator bolt and installation kit for 1967 Mercury Cougar and Ford Mustang with 390 engines. Includes spacer and pivot bolt and the other three bolts and washers as shown.
Bolt and nut for the clamping the coil into the coil bracket as found in 1967-73 Mercury Cougar and Ford Mustang. Fits all of the various coil brackets used 1967-73 on most all Ford engines. This is a 8-32x1-1/2, 1/4 hex headed fine thread bolt and nut. This is not the round headed slotted screw type that Ford also used.
Kit comes complete with J bolts and mounting nuts. Replaces Ford Part #: D0AZ-10756-K.
Oil pan bolt kit for all FE 390, 427, and 428 engines. Set is made by AMK and includes 20 OEM style bolts and washers. We sell them specifically for 1967-70 Mercury Cougar and Ford Mustang, but they will fit most all Ford "FE" engines including 352, 410, and 360 Ford engines. If you happen to have a 428CJ with windage tray, we also offer a set of bolts for that application too. ...
Fits 1967 - 1973 Standard or XR7
Concours correct for 67, but a nice dress-up item for 68-73. Replaces Ford Part # 382627 Four bolts, four washers and eight rubber washers in mounting kit.
Reproduction Vent Frame Bolt Kit 1967 and 1968 Mercury Cougar and Ford Mustang
This is the Water Pump Bolt Kit for 1968 Mercury Cougar and 1968 Ford Mustang with the 289 or 302 engines with air conditioning. Quality kit by AMK Products - F-305. This kit comes with an instruction sheet, and shows the correct placement of the bolts.
This is the Water Pump Bolt Kit for 1967 Mercury Cougar and 1967 Ford Mustang with the 289 engines with air conditioning. Quality kit by AMK Products - F-249. This kit comes with an instruction sheet, and shows the correct placement of the bolts.
New Bolt kit, for the installation of a water pump on any Ford 352, 390, or 428CJ engine. Fits all 1967-70 Mercury Cougar and Ford Mustang with 390-4V, 390-2V, and 428 Cobra Jet engines.
New valve cover bolts for all 289-2V, 289-4V, 302-2V, 302-4V, and 351W-2V, and 351W-4V Ford engines. These are the AMK bolts with original style Ford assembly line head markings. Correct 7/16 hex head and split tooth captured washer, sold in sets of 12.*Note - Excludes Boss 302 and 351C engines (see part number 8317)Replaces Ford part number 373071-S.
Reproduction valve cover bolts for all 390 / 427 / 428 Ford engines.
Cylinder head bolt set for any 1965-73 Ford 260, 289, or 302 engine. 10 short and 10 long, Grade 8 cylinder head bolts. Proper lengths for Ford small block engines. Not for 351W cylinder heads. See related items for individual long or short cylinder head bolts.* Note, excludes 351W cylinder heads.
Cylinder head bolt set for any 1967-70 Ford 390 or 428CJ engine. 10 short and 10 long, Grade 8 cylinder head bolts. Proper lengths for Ford FE engines. See related items for individual long or short cylinder head bolts.
Fastens the battery tray to the fender apron.
Reproduction bolts and washers for the C-4 automatic bell housing on any 1967-68 Cougar or Mustang equipped with a 289 / 302 engines and code W automatic transmissions. Bell housing to engine block bolts. Fits most all other Ford small block V-8's from 1965-68.
Reproduction bolts and washers for the C-6 automatic bell housing on any 1967-70 Cougar or Mustang equipped with a 390 / 428 engines and code U automatic transmissions. Bell housing to engine block bolts. Fits most all other Ford big block V-8's from 1966-70.
Reproduction bolts and washers for the manual transmission bell housing on any 1967-68 Cougar or Mustang equipped with a 289 / 302 engines and either 3 or 4 speed manual stick shift transmissions. Bell housing to engine block bolts. Fits most all other Ford small block V-8's from 1967-68.
Reproduction bolts and washers for the manual transmission bell housing on any 67 - until 2/1968 Cougar or Mustang equipped with a 390 / 428.
Reproduction bolts and washers for the manual transmission bell housing on mid , like Feb 1968 - 1970 Cougar or Mustang or other Ford car equipped with a 390 / 428 engines. Bell housing to engine block bolts.
Four of these bolts are used to secure the isolator portion of the engine mounts to the 289/302/351 blocks. Includes 351W and 351C engines. 5/8" hex head bolt. Sold as a set of 4. Concours phosphate & Oil (gray-black).
Concours bolt set for all 1968-70 Mercury Cougar and Ford products including Mustang, radiator fan clutch to radiator cooling fan. 1/2 inch hex head size. Threads are 5/16-18. Four bolts with captured split washers. Also sold individually. ...
Concours bolt set for all 1968-70 Mercury Cougar and Ford products including Mustang radiator fan clutch to water pump. 1/2 inch hex head size. Threads are 5/16-24. Also sold individually. These bolts have an approximate length of 7/8" to the shoulder and an approximate overall length of 1-1/8". ...
These reproduction fender to pillar bracket bolts fit both the Standard and XR7.
Reproduction set of idler arm bolts for the 1967 - 1968 Cougar or Mustang.
New set of bolts for fastening the transmission inspection cover on all 1967-70 Mercury Cougar, Ford Mustang, and Ford anything with 390, 428CJ, and 352 or any FE style Ford engine. Includes 3 and 4 speed transmissions.
Pair (2) Bolts for securing the inspection cover for any C-4 automatic transmission 1967-68 Mercury Cougar or 1965-70 Ford Mustang. Additionally also fits FMX transmissions 1969-73 Mercury Cougar.or Ford Mustang.