Your cart is empty!
Our shopping cart requires the use of cookies. If you have your cookies disabled, please enable them for our site to place an order. If you have cookies enabled and have added an item to your cart, but you are still seeing this message, that could indicate that the cookie for our shopping cart is corrupted on your computer.You should be able to fix this by either:
Buy Details
Clutch equalizer pivot mount, engine side. Fits all 1971 - 1973 Mercury Cougar with 351 Cleveland engine, and 1971 - 1973 Ford Mustangs with 302 or 351 Cleveland engine. Replaces Ford part #: D1ZZ-7A572-A.
C8AZ-7515-B Manual transmission clutch fork - 3 and 4 speed, stick shift transmissions. Fork measures 12-5/16 inches long. Alternate number C8AA-7515-B or C8AA-7541-B. Couple of variations of this fork. Most versions will not be stamped. Spring and side holes not needed for Mustang and Cougar applications. Originally for 1968 full sized cars with 289 or 302 engines and manual transmissions. Maybe 6 cylinders, not sure, but vert likely. Cougar 1971 - 1973, 351 Engines. Mustang 1971 - 1973,...
Clutch Fork Pivot for Cougars manufactured after 2/16/1968. Replaces Ford Part #: C8AZ-7522-A.
Manual transmission clutch kit for all 1967-73 Mercury Cougar or Ford Mustang with 3 or 4 speed transmissions and 289, 302, or 351 engines. This is a 10 inch disk, pressure plate, throw out bearing, pilot bearing, and alignment tool. The clutch disc is asbestos free.
These clutch pedals feature an improved design (removable pin) for easier installation. Compatible with existing hanger assembly even in automatics. Replaces Ford Part # D1ZZ-7519-B.
D1ZZ-7519-B Good used pedal but these pedals will no doubt show some wear around the clutch rod holes. Three and four speed pedals are all the same. Mustang is the same too.
These reproduction pads are high quality replacements for worn or missing original pads. Replaces Ford part number C9ZZ-7A624-A.
Manual transmission clutch throw out bearing for all 1967-73 Mercury Cougar or Ford Mustang with 3 or 4 speed transmissions and 289, 302, or 351 engines. This is with a 10 inch disc.
For all 1971 to 1973 Cougars and Mustangs with H code 351-2V and FMX automatic transmissions. Ford part number D1ZZ-6A023-B.*NOTE* Two notes - There is a difference between 1969-70 and 1971-73 FMX cross members. Additionally, Ford did produce H code 351-2V engines with C-6 transmissions. Triple check.
Reproduction clutch lever dust boot for the Mercury Cougar or Ford Mustang. This unit is used with the 429 in 1971 and in all Cougars and Mustangs in 1972 and 1973 equipped with manual transmissions and the 351 engine.Replaces Ford part #C5AZ-7513-A.
After being obsolete for years we have brought back another hard to find clutch equalizer component for 1971-3 Mustang and Cougar. Numerous other Ford application too. Replaces Ford part # C5AZ-7B545-A
Exact Copies Made From the Original Supplier to Ford Motor Co. U.S.A. Made. Ramp-Lok Features a Special Conical Washer Designed Specifically for Exhaust Manifolds.
Filter / screen for the C6 transmissions, for all 1967-73 and 1967-73 Mercury and Ford.
Replacement filter for FMX transmissions. Fits all Ford FMX transmissions for any 1969-73 Mercury Cougar or Ford Mustang with that X code FMX transmission.
Replacement transmission pan filter and pan gasket kit. For the C-6 (U Code) transmission. Replaces Ford Part Number: C7ZZ-7A098
Replacement transmission pan filter and pan gasket kit. For the FMX (X Code) transmission. Replaces Ford Part Number: C9ZZ-7A098
Replaces Ford Part # : D1ZZ-3513-A. For use only with 3 and 4 speed manual transmission cars.
All steel fitting for the lower radiator tank, found on all cars with automatic transmissions. The fine threads go to the radiator and the transmission cooling line screws onto the flared fitting after installation into the radiator. Two needed per car, sold individually. Fits all years 1967-73, and all automatic transmissions. 1/2" threads go to cooling lines. 3/8" threads go into the radiator. *Note - This is an original steel fitting, not a brass reproduction. ...
New flat nut, these attach both the shifter seal and shifter dial to the under side of the automatic shifter bezel. Check out our video on rebuilding your shifter below: ...
Good used OEM flex plate for all 69 - 73 Mercury Cougar and Ford Mustang with 302 / 351W engines, and C4 or FMX transmissions. Not for use on a 1968 with 302. The starter ring will show wear and some will choose to replace, others have removed the starter ring and just turned it around so the unused portion of the ring will now contact the starter drive gear. ...
Brand new flex plate for all 1970-71 Mercury and Ford with 429CJ engines, and C6 transmissions. Comes complete with new starter ring gear installed as shown.
Gasket, for the C6 transmission filter. Fits all c-6 transmissions 1967-73 Mercury Cougar and Ford and Mustang.
Fits 3 speed or 4 speed manual floor shifts. Sold individually. Check out our video on rebuilding your shifter below:
New hairpin clip for attaching the brake light switch to the brake pedal. This clip was also used to attach the clutch rod to the clutch pedal on manual transmission cars. Fits all years 1967-73, Ford and Mercury.Replaces Ford part number 380699-S.
1971 - 1973 Small block engine (351 cubic inch) and C-6 automatic transmission inspection cover. Transmission code 'U' found on select 1971-73 Cougars and 1971-73 Mustangs. Inspection plate for the flex plate and torque converters.Ford part number D1OZ-7986-A.
Reproduction dust and safety cover for 69 - 73 Cougars and Mustangs with the FMX (X code) automatic transmission. Access plate for the torque converter and flex-plate.NOTE - Although the FMX and the C4 inspection plate look similar visually, they are in fact different sizes with different bolt spacing.
Used dust and safety cover for all 69 - 73 Cougars and Mustangs with the FMX (code X) automatic transmission. Access plate for the torque converter and flex-plate.
This is the bolt to hold the battery onto the battery tray. Battery hold down bolt only. Sold individually. Replaces Ford Part # : D0AZ-10756-A
Used on both 351 2V and 4V motors equipped with the C6 transmission. Approximately 26-1/2" with red color code. The comparison picture with two rods side by side are the 71 - 73 FMX and C6 rods. *NOTE* Many assume the C6 was only available with a 351 equipped with a 4V but in fact you could get a C6 with a 351 2V in 1971 - 1973.
This rod was used on all Cougars 1971 - 1973 equipped with a 351 and FMX transmission both 4V and 2V. Approximately 27" Black color code.
Ford calls this part a 'mask'. This clamps to the chromed lever and holds the socket and bulb that are attached to the neutral safety switch, which are the shifter indicator light for the floor shifter. This cast piece will not have stripped treads or be corroded. It also fits 1971 and newer Maverick and Comet with floor shifters only. Ford part number C9ZZ-7B052-A. Check out our video on rebuilding your shifter below: ...
Manual control shift linkage assembly for a floor shift FMX transmission in any 1971-73 Mercury Cougar or Ford Mustang. Comes as shown. *Note - this will not work with a C6 transmission.
Rod used for locking the C-6 transmission in "Park". Connects to the lower tab of the steering column and the C-6 transmission shift arm. Prevents the transmission from shifting out of park when the ignition key is removed. Rod is about 13 inches long and was originally marked with a red paint mark or daub. Casting number stamped on the rod - D1ZA-7E330-BA. The C-6, automatic transmission, could be ordered with any engine from 1971 - 1973. Transmission code "U" on your door data tag.
Rod used for locking the FMX transmission in "Park". Connects to the lower tab of the steering column and the FMX transmission shift arm. Prevents the transmission from shifting out of park when the ignition key is removed. Rod is about 13 inches long and was originally marked with a yellow mark. Casting number stamped on rod - D1ZA-7E330-AA. The FMX, automatic transmission, was used on all 1971 - 1973 Cougars with the 351-2V engine (Letter "H" in the 5th position of your VIN). Transmission...
Ford manual transmission flywheel and automatic transmission flex plate mounting bolts. 6 bolts required, sold individually. Replaces Ford part # 378172-S
RAT-BZ1 Original equipment 3 speed top loader 3.03 transmission from a 1972 Mercury Cougar with engine code H - 351-2V only. This transmission was used after 12-1-1971 through the end of the 1972 model year. Ford master part number D2ZZ-7003-G.Percentages of Cougars equipped with a manual transmission by year1967 = 18.5%1968 = 13.2%1969 = 10.5%1970 = 7.8%1971 = 2.8%1972 = 1.5%1973 = 0.7%Total for 1967 to 1973 = 10.1% (Mustangs for the same time frame were 25.2%)Percentage of each...
RAT-BZ Original equipment 3 speed top loader 3.03 transmission from a 1972 Mercury Cougar with engine code H - 351-2V only. This transmission was used from the beginning of the model year through 12-1-1971. Ford master part number D2ZZ-7003-C.Percentages of Cougars equipped with a manual transmission by year1967 = 18.5%1968 = 13.2%1969 = 10.5%1970 = 7.8%1971 = 2.8%1972 = 1.5%1973 = 0.7%Total for 1967 to 1973 = 10.1% (Mustangs for the same time frame were 25.2%)Percentage of each transmission;X...
These little rivets are used to affix the ID tag to the passenger side of the 3 and 4 speed top-loader transmissions. Most tags are held in place by two rivets but on some only two are used from the factory.
Complete engine mounting hardware kit for the 72-73 351C 2-barrel engine. See below for list of included hardware. Click on images to enlarge.
Complete engine mounting hardware kit for the 72-73 351C 4-barrel engine. See below for list of included hardware. Click on images to enlarge.
Complete engine mounting kit for the 390 engine with standard exhaust. See list below for included hardware.Click on images to enlarge. ...
Designed as a direct-fit OE-style replacement, this modulator valve will fit directly into the factory location of your current Cougar or Mustang valve. Also known as the throttle valve, this valve controls vacuum to the transmission as you press the gas pedal, and it will apply higher control pressure for better quality shifts at higher RPMs.
Stainless Steel Modulator Vacuum Line for all V8 engines with a C6 transmission except 429CJ or the 351C with a 4 barrel carburetor.
Reproduction Stainless Steel FMX Transmission Modulator Line for the 1972-1973 Mercury Cougar or Ford Mustang
Reproduction OE Steel Transmission Modulator Line for the 1972-1973 Mercury Cougar or Ford Mustang with a 351 and a FMX Transmission.
Locking nut that attaches the shift lever to the shifter arm and support inside the shifter buckets. We normally see the course threaded nuts on the 1971-73 shifters. Please check your shift arm support for correct threads. Check out our video on rebuilding your shifter below: ...
Replaces Ford part # 55806-S
Replaces Ford part # C2DZ-6A529 Sold Individually.